缝合复合材料II型层间断裂特性研究

分别采用测量ENF试样加载点位移与测量其端部剪切位移CSD(Crack Shear Displacement)的试验方法,研究了缝合复合材料层合板的II型层间断裂韧性以及缝合密度,缝合线的直径等缝合参数对于缝合复合材料层合板II型层间断裂韧性和分层模式的影响。结果表明,缝合降低了层合板初始分层韧性G_IIi,但对于分层的扩展有良好的抑制作用。缝合参数对此有较大影响。      

CF/EP composite laminates with carbon black and copper chloride for improved electrical conductivity and interlaminar fracture toughness

An experimental study was conducted to improve the electrical conductivity of continuous carbon fibre/epoxy (CF/EP) composite laminate, with simultaneous improvement in mechanical performance, by incorporating nano-scale carbon black (CB) particles and copper chloride (CC) electrolyte into the epoxy matrix. CF/EP laminates of 65 vol.% of carbon fibres were manufactured using a vacuum-assisted resin infusion (VARI) technique. The effects of CB and the synergy of CB/CC on electrical resistivity, tensile strength and elastic modulus and fracture toughness (K_IC) of the epoxy matrix were experimentally characterised, as well as the transverse tensile modulus and strength, Mode I and Mode II interlaminar fracture toughness of the CF/EP laminates. The results showed that the addition of up to 3.0 wt.% CB in the epoxy matrix, with the assistance of CC, noticeably improved the electrical conductivity of the epoxy and the CF/EP laminates, with mechanical performance also enhanced to a certain extent.     

DCB test simulation of stitched CFRP laminates using interlaminar tension test results

A simulation model for the delamination extension of stitched CFRP laminates and 3-D orthogonal interlocked fabric composites (3-D OIFC) has been developed using a 2-D finite element method incorporating interlaminar tension test results to simulate the experimental results of their DCB tests. The mechanical properties of through-the-thickness fiber were determined from the results of interlaminar tension tests in which the specimen included only one through-the-thickness yarn. The fracture phenomena around the through-the-thickness thread, such as debonding from the in-plane layer, slack absorption, fiber bridging, and the pull-out of broken threads from the in-plane layers, are also introduced into the FEM model. The present FEM simulation results were compared to DCB test results for certain stitched laminates and a 3-D OIFC, and the simulation results showed good agreement with the experimental results of DCB tests, including the load–displacement curve and Mode I strain energy release rate (GI). While it was difficult to estimate GI accurately when the DCB test specimen included different types of z-fiber fracture modes, the present model of FEM analysis can simulate the experimental results of DCB tests of stitched laminates and 3-D OIFC. It is suggested that the GI of CFRP with arbitrary z-fiber densities can be predicted by using this FEM analysis model together with interlaminar tension test results.     

Influence of silane coupling agents on interlaminar fracture in glass fibre fabric reinforced unsaturated polyester laminates

The relationship between the adhesive properties of the interphase of glass fibre/resin and the resultant composite Mode I delamination fracture toughness in glass fibre fabric laminate (GFFL) was studied. The Mode I interlaminar fracture toughness of GFFL was obtained by using a double cantilever beam (DCB) specimen. The delamination resistance of GFFLs which have two silane coupling agents and three concentration finishes is discussed on the basis of interlaminar fracture toughness. The crack propagation behaviour of DCB testing was mainly divided into stable and unstable manners. The fracture toughness and the crack propagation behaviour were dependent on the types and concentration of silane coupling agents.     

Mode II interlaminar fracture properties of Moso bamboo

Bamboo is a kind of biological composites reinforced by unidirectional long fiber. Once there exists crack, the propagation of delamination is controlled by the interlaminar fracture toughness instead of by strength. In this paper, the end notched flexure (ENF) beam specimen was used to test the Mode II interlaminar fracture toughness G_IIC along grain of Moso bamboo internode and the fracture surface was analyzed. The results were obtained that the Mode II interlaminar fracture toughness G_IIC calculated by the experiment parameter substitution method was more accurate and the value was 1303.18 J/m² (coefficient of variation = 8.96%) which was about three times higher than the value of Mode I interlaminar fracture toughness; the crack propagation of Mode II interlaminar fracture was mainly self-similar cracking, but the fracture surface was rougher. Ground tissue in the zone of Mode II crack propagation was characterized by hackle shearing deformation. The SEM photos showed that ground tissue separated from fiber along middle lamella under shear stress and as the increasing of the dislocation of upper and lower layer, the thin-walled ground tissue would fracture transversely by tension, while to thick-walled fiber cell, only middle lamella and primary wall were torn then debonded, fragments remained.     

Role of Interface Modification on the Mode I and Mode II Fracture Behavior of Glass Fabric / Vinyl Ester Composites

The objective of this study was to determine the influence of five different combinations of silane coupling agents on the Mode I and Mode II fracture toughness and strength of woven glass fabric / vinyl ester composite laminates. Double Cantilever Beam (DCB) and End Notch Flexure (ENF) tests were conducted to estimate the influence of surface treatment of glass fabric wilh methacryl silane and methanol washing, on the Mode I and Mode II fracture toughness, respectively. The results were compared with those of a conventional epoxy silane coated composite. It was found that an increasing content of methacryl silane (0.01 wt.% to 1.0 wt.%) reduced the Model fracture toughness and enhanced the Mode II fracture toughness values. Methanol washing after treatment with melhacryl sitane resulted in an increase of both Mode I and Mode II fracture toughness values.     

微胶囊层间增韧碳纤维/环氧树脂复合材料力学性能的超声导波评价

选用微胶囊作为改性材料,采用热压机层压成型工艺制备出微胶囊层间增韧T300碳纤维/环氧树脂(CF/EP)复合材料。通过双悬臂梁(DCB)Ⅰ型层间断裂试验评估了CF/EP复合材料的增韧效果。利用超声导波技术对普通CF/EP复合材料和增韧CF/EP复合材料层间力学性能进行评价。通过SEM对CF/EP复合材料层间断面微观形貌进行观察,以揭示微胶囊的增韧机制,同时对超声导波检测结果进行辅助说明。结果表明,微胶囊以团聚形式分布在层间基体中,可以有效提高CF/EP复合材料的层间断裂韧性。微胶囊的填充改变了CF/EP复合材料层间基体特性,增加了导波传播过程中的衰减,导致响应信号峰值降低。同时,团聚的微胶囊改变了CF/EP复合材料对于中心频率125 kHz五峰波激励的振动响应,导致中心频率在信号频谱中的幅值低于普通CF/EP复合材料。      

Numerical investigation to prevent crack jumping in Double Cantilever Beam tests of multidirectional composite laminates

During the experimental characterization of the mode I interlaminar fracture toughness of multidirectional composite laminates, the crack tends to migrate from the propagation plane (crack jumping) or to grow asymmetrically, invalidating the tests.The aim of this study is to check the feasibility of defining the stacking sequence of Double Cantilever Beam (DCB) specimens so that these undesired effects do not occur, leading to meaningful onset and propagation data from the tests. Accordingly, a finite element model using cohesive elements for interlaminar delamination and an intralaminar ply failure criterion are exploited here to thoroughly investigate the effect of specimen stiffness and thermal residual stresses on crack jumping and asymmetric crack growth occurring in multidirectional DCB specimens.The results show that the higher the arm bending stiffness, the lower the tendency to crack jumping and the better the crack front symmetry. This analysis raises the prospect of defining a test campaign leading to meaningful fracture toughness results (onset and propagation data) in multidirectional laminates.     

Simultaneous binding and ex situ toughening concept for textile reinforced pCBT composites: Influence of preforming binders on interlaminar fracture properties

A new concept consisting of binding and ex situ toughening is proposed for manufacturing and toughening of textile reinforced pCBT composites. The present study assesses the influence of various preforming binders on interlaminar fracture properties. Interlaminar fracture toughness of textile reinforced pCBT composites was investigated under mode I and mode II deformation. A standard double cantilever beam (DCB) test and an end notched flexure (ENF) test based on a three-point bending test were applied to evaluate the interlaminar fracture toughness in mode I and mode II, respectively. The effect of binder type, filling content and preparation concept on fracture properties under the mentioned two deformation modes were discussed on the basis of morphology analysis of fracture sections with scanning electric microscopy. Flexural properties of the textile reinforced pCBT laminates prepared using the selected preforming binder were characterized for further verification of the performance of the proposed concept.     

Interlaminar fracture toughness of CFRP in Mode I and Mode II determined by Raman spectroscopy

Fracture toughness of multidirectional Carbon Fiber Reinforced Plastics (CFRP) for Mode I and Mode II was investigated using Double Cantilever Beam (DCB), End Notched Flexure (ENF) specimens and Raman Coating Method. The distribution of strain near the crack tip of CFRP was measured by Raman spectroscopy. Thin films of PbO on the measured surface of the DCB and ENF specimens were deposited by physical vapor deposition as the pretreatment to measure the strain by Raman spectroscopy. The fracture toughness of multidirectional CFRP in both Mode I and Mode II was determined using the results measured by Raman spectroscopy. This result coincided with those measured by conventional methods.     

Influence of electrospun Nylon 6,6 nanofibrous mats on the interlaminar properties of Gr-epoxy composite laminates

The present work aims at investigating the influence of electrospun Nylon 6,6 nanofibrous mat to interlaminar strength. Mode I and the Mode II fracture mechanics of virgin and nanomodified laminates are investigated. Nanomodified laminates are fabricated by interleaving an electrospun nanofibrous mats in laminate mid-plane. Double Cantilever Beam (DCB) and End Notched Flexure (ENF) tests are performed on both virgin and nanomodified configuration. Results show that electrospun nanofibrous mat is able to increase by 23.2% the mechanical energy absorbing capability and by about 5% the G_IC. ENF tests reveal that the nanofibrous mats contribute to improve the maximum stress before the material crisis (6.5% of increment) and a measurable increment of (8.1%) the maximum mechanical energy that can be absorbed by the material during the crack propagation is registered. The acoustic emission (AE) technique is used to monitor both DCB and ENF tests. The AE information highlight that the nanofibrous mats mitigate the interlaminar matrix failure on both the fracture modes.     

Characterization of transverse tensile, interlaminar shear and interlaminate fracture in CF/EP laminates with 10 wt% and 20 wt% silica nanoparticles in matrix resins

The transverse tensile properties, interlaminar shear strength (ILSS) and mode I and mode II interlaminar fracture toughness of carbon fibre/epoxy (CF/EP) laminates with 10 wt% and 20 wt% silica nanoparticles in matrix were investigated, and the influences of silica nanoparticle on those properties of CF/EP laminates were characterized. The transverse tensile properties and mode I interlaminar fracture toughness (G_IC) increased with an increase in nanosilica concentration in the matrix resins. However, ILSS and the mode II interlaminar fracture toughness (G_IIC) decreased with increasing nanosilica concentration, especially for the higher nanosilica concentration (20 wt%). The reduced G_IIC value is attributed to two main competing mechanisms; one is the formation of zipper-like pattern associated with matrix microcracks aligned 45° ahead of the crack tip, while the other is the shear failure of matrix. The ratio of G_IIC/G_IC decreased with the concentration of silica nanoparticles, comparable with similar CF/EP laminates with dispersed CNTs in matrix. Fractographic studies showed that interfacial failure between carbon fibre and epoxy resin occurred in the neat epoxy laminate, whereas a combination of interfacial failure and matrix failure occurred in the nanosilica-modified epoxy laminates, especially those with a higher nanosilica concentration (20 wt%).     

Fracture toughness improvement of CFRP laminates by dispersion of cup-stacked carbon nanotubes

Several techniques are introduced to enhance the interlaminar fracture toughness of CFRP laminates using cup-stacked carbon nanotubes (CSCNTs). Prepared CSCNT-dispersed CFRP laminates are subject to Double Cantilever Beam (DCB) and End Notched Flexure (ENF) tests in order to obtain mode-I and mode-II interlaminar fracture toughness. The measured fracture toughnesses are compared to that of CFRP laminates without CSCNT to evaluate the effectiveness of CSCNT dispersion for the improvement of fracture toughness. All CSCNT-dispersed CFRP laminates exhibit higher fracture toughness, and specifically, CSCNT-dispersed CFRP laminates with thin epoxy interlayers containing short CSCNTs have three times higher fracture toughness than CFRP laminates without CSCNT. SEM observation of fracture surfaces is also conducted to investigate the mechanisms of fracture toughness improvement. Crack deflection mechanism is recognized in the CSCNT-dispersed CFRP laminates, which is considered to contribute the enhancement of interlaminar fracture toughness.     

Experimental investigation on test methods for mode II interlaminar fracture testing of carbon fiber reinforced composites

In this paper, experimental investigation on the test methods for mode II interlaminar fracture testing of carbon fiber reinforced composites are carried out. Mode II interlaminar fracture testing of unidirectional composite of carbon fiber reinforced epoxy (T800/#3631) are conducted using four kinds of test methods, namely end notched flexure (ENF) test, end loaded split (ELS) test, four-point bend end notched flexure (4ENF) test, and over notched flexure (ONF) test. An analytical model based on a point-friction assumption and classical beam theory is proposed to evaluate the effect of friction between crack faces on the mode II interlaminar fracture toughness in the 4ENF and ONF tests. The analytical model is validated by the comparison of analytical results with previous ones obtained from finite element analysis. Experimental results show that the ENF test gives reliable initiation value of fracture toughness with a small scatter and that the average value of fracture toughness obtained from 4ENF test is about 2% higher than that obtained from the ENF test. The effect of friction in the 4ENF test is much lower than that in the ONF test in which the effect of friction increases with the crack growing. It is concluded that the 4ENF test method is an effective test method for the experimental evaluation of mode II propagation interlaminar fracture toughness of carbon fiber reinforced composites.     

缝合层合板的I型层间断裂韧性研究

通过缝合的方法改善织物增强复合材料层合板的层间断裂韧性.采用双悬臂梁(DCB)试验测试和研究了缝合层合板的层间断裂韧性与断裂行为.为了评价缝合工艺参数(缝合密度)对层间断裂韧性的影响, 用改进的插入型夹具在实测不同缝合工艺层合板的I型层间断裂韧性值(GIC)的基础上, 分析和阐明了缝合工艺参数(缝合密度)与GIC间的关系; 以提高层合板的平均层间断裂韧性值为目标, 以拉伸和弯曲强度为约束条件优化了缝合工艺; 采用摄影显微镜对分层断裂面进行了观察, 分析和考察了缝合对其它性能的影响.结果表明 改进的插入型夹具可方便地完成缝合层合板的I型层间断裂韧性测试; 缝合后裂纹不连续扩展, 缝合密度对裂纹扩展行为有较大影响; 随着缝合密度的增大, 层间断裂韧性值增大, 但拉伸和弯曲强度降低, 缝合密度存在最佳值.     

Mode I and Mode II interlaminar fracture toughness of composite laminates interleaved with electrospun nanofibre veils

In this study, the effects of interleaved nanofibre veils on the Mode I and Mode II interlaminar fracture toughness (ILFT) of autoclave cured unidirectional carbon/epoxy composite laminates were investigated. Various electrospun nanofibre veils consisting of a range of different polymer types, fibre diameters and veil architectures were placed in the laminate mid-planes, which were subsequently subjected to double cantilever beam and end-notch flexure tests. It was found that the polymer type and veil areal weight were the most important factors contributing to laminate performance. A 4.5 g/m² PA66 veil provided the best all-round performance with fracture toughness improvements of 156% and 69% for Mode I and Mode II, respectively.     

缝合层合板的Ⅰ型层间断裂韧性研究

通过缝合的方法改善织物增强复合材料层合板的层间断裂韧性.采用双悬臂梁(DCB)试验测试和研究了缝合层合板的层间断裂韧性与断裂行为.为了评价缝合工艺参数(缝合密度)对层间断裂韧性的影响,用改进的插入型夹具在实测不同缝合工艺层合板的Ⅰ型层间断裂韧性值(G_IC)的基础上,分析和阐明了缝合工艺参数(缝合密度)与G_IC间的关系;以提高层合板的平均层间断裂韧性值为目标,以拉伸和弯曲强度为约束条件优化了缝合工艺;采用摄影显微镜对分层断裂面进行了观察,分析和考察了缝合对其它性能的影响.结果表明:改进的插入型夹具可方便地完成缝合层合板的Ⅰ型层间断裂韧性测试;缝合后裂纹不连续扩展,缝合密度对裂纹扩展行为有较大影响;随着缝合密度的增大,层间断裂韧性值增大,但拉伸和弯曲强度降低,缝合密度存在最佳值.     

Interlaminar fracture of CF/EP composite containing a dual-component microencapsulated self-healant

We present an experimental study of the self-healing ability of carbon fibre/epoxy (CF/EP) composite laminates with microencapsulated epoxy and its hardener (mercaptan) as a healing agent. Epoxy- and hardener-loaded microcapsules (average size large: 123 μm; small: 65 μm) were prepared by in situ polymerisation in an oil-in-water emulsion and were dry-dispersed at the ratio 1:1 on the surface of unidirectional carbon fabric layer. The CF/EP laminates were fabricated using a vacuum-assisted resin infusion (VARI) process. Width-tapered double cantilever beam (WTDCB) specimens were used to measure mode-I interlaminar fracture toughness of the CF/EP composites with a pre-crack in the centre plane where the microcapsules were placed. Incorporation of the dual-component healant stored in the fragile microcapsules provided the laminates with healing capability on delamination damage by recovering as much as 80% of its fracture toughness. It was also observed that the recovery of fracture toughness was directly correlated with the amount of healant covering the fracture plane, with the highest healing efficiency obtained for the laminate with large capsules.     

平纹织物结构对织物增强复合材料层间断裂韧性影响的研究

本文采用粘贴片式双悬臂梁(DCB)试件和端部切口弯曲(ENF)试件研究了平纹织物的经纬纱密度对玻璃平纹织物/环氧树脂复合材料的Ⅰ型和Ⅱ型层间断裂韧性的影响。实验结果表明织物的密度对层间断裂韧性有显著的影响。提出了在织物增强复合材料层合板中,基体在织物孔洞中形成层间铆接,并且就其与层间G_IC和G_IC的关系进行了研究。      

Influence of adsorption behaviour of a silane coupling agent on interlaminar fracture in glass fibre fabric-reinforced unsaturated polyester laminates

The relationship between the interphase consisting of physisorbed and chemisorbed silane on glass fibres and the resultant composite Mode I delamination fracture toughness in glass fibre fabric laminate, was studied. The Mode I interlaminar fracture toughness of the laminate specimen was obtained by using a double cantilever beam (DCB) specimen. The delamination resistance of the laminate specimen finished with two silane concentrations and washed in methanol solvent, is discussed on the basis of the interlaminar fracture toughness. In order to determine the amount of physisorbed and chemisorbed silane on the glass fibre, the amount of total carbon was determined using an analysis instrument. The physisorbed silane migrated into the resin matrix and influenced the mechanical properties and interlaminar fracture of the laminate specimen. The amount of unsaturated polyester resin blended with a silane coupling agent was measured using dynamic mechanical spectroscopy, and a DCB specimen for mechanical properties and fracture toughness.