Fabrication and effective thermal conductivity of multi-walled carbon nanotubes reinforced Cu matrix composites for heat sink applications

A novel particles-compositing method was used for the first time to disperse different contents of multi-walled carbon nanotubes (CNTs) in micron sized copper powders, which were subsequently consolidated into CNT/Cu composites by spark plasma sintering (SPS). Microstructural observations showed that the homogeneous distribution of CNTs and dense composites could be obtained for 0–10 vol.% CNT contents. The CNT clusters were appeared in the powder mixture with 15 vol.% CNTs, which resulted in an insufficient densification of the composites. The effective thermal conductivity of the composites was analyzed both theoretically and experimentally. The addition of CNTs showed no enhancement in overall thermal conductivity of the composites due to the interface thermal resistance associated with the low phase contrast of CNT to copper and the random tube orientation. Besides, the composite containing 15 vol.% CNTs led to a rather low thermal conductivity due possiblely to the combined effect of unfavorable factors induced by the presence of CNT clusters, i.e. large porosity, lower effective conductivity of CNT clusters themselves and reduction of SPS cleaning effect. The CNT/Cu composites may be a promising thermal management material for heat sink applications.     

Poly(vinyl alcohol) reinforced with large-diameter carbon nanotubes via spray winding

For practical application of carbon nanotube (CNT)/polymer composites, it is critical to produce the composites at high speed and large scale. In this study, multi-walled carbon nanotubes (MWNTs) with large diameter (∼45 nm) and polyvinyl alcohol (PVA) were used to increase the processing speed of a recently developed spraying winding technique. The effect of the different winding speed and sprayed solution concentration to the performance of the composite films were investigated. The CNT/PVA composites exhibit tensile strength of up to 1 GPa, and modulus of up to 70 GPa, with a CNT weight fraction of 53%. In addition, an electrical conductivity of 747 S/cm was obtained for the CNT/PVA composites. The good mechanical and electrical properties are attributed to the uniform CNTs and PVA matrix integration and the high degree of tube alignment.     

In situ polymerized nanocomposites: Polystyrene/CNT and Poly(methyl methacrylate)/CNT composites

Carbon nanotubes (CNTs) were incorporated into polystyrene (PS) and poly(methyl methacrylate) (PMMA) matrices via in situ emulsion and emulsion/suspension polymerization methods. The polymerizations were carried out using various initiators, surfactants, and carbon nanotubes to determine their influence on polymerization and on the properties of the composites. The loading of CNTs in the composites varied from 0 to 15 wt.%, depending on the CNTs used. Morphology and dispersion of the CNTs were analyzed by transmission and scanning electron microscopy techniques. The dispersion of multi-walled carbon nanotubes (MWCNT) in the composites was excellent, even at high CNT loading. The mechanical properties, and electrical and thermal conductivities, of the composites were also analyzed. Both electrical and thermal conductivities were improved.     

Mechanical and electrical property improvement in CNT/Nylon composites through drawing and stretching

The excellent mechanical properties of carbon nanotubes (CNTs) make them the ideal reinforcements for high performance composites. The misalignment and waviness of CNTs within composites are two major issues that limit the reinforcing efficiency. We report an effective method to increase the strength and stiffness of high volume fraction, aligned CNT composites by reducing CNT waviness using a drawing and stretching approach. Stretching the composites after fabrication improved the ultimate strength by 50%, 150%, and 190% corresponding to stretch ratios of 2%, 4% and 7%, respectively. Improvement of the electrical conductivities exhibited a similar trend. These results demonstrate the importance of straightening and aligning CNTs in improving the composite strength and electrical conductivity.     

Formation and mechanical characterisation of SU8 composite films reinforced with horizontally aligned and high volume fraction CNTs

Carbon nanotube (CNT) reinforced composites have been identified as promising structural materials for the mechanical components of microelectromechanical systems (MEMS), potentially leading to advanced performance. High alignment and volume fraction of CNTs in the composites are the prerequisites to achieve such desirable mechanical characteristics. In particular, horizontal CNT alignment in composite films is necessary to enable high longitudinal moduli of the composites which is crucial for the performance of microactuators. A practical process has been developed to transfer CNT arrays from vertical to horizontal alignment which is followed by in situ wetting, realign and pressurized consolidation processes, which lead to a high CNT volume fraction in the range of 46-63%. As a result, SU8 epoxy composite films reinforced with horizontally aligned CNTs and a high volume faction of CNTs have been achieved with outstanding mechanical characteristics. The transverse modulus of the composite films has been characterised through nanoindentation and the longitudinal elastic modulus has been investigated. An experimental transverse modulus of 9.6 GPa and an inferred longitudinal modulus in the range of 460-630 GPa have been achieved, which demonstrate effective CNT reinforcement in the SU8 matrix.     

Electrical conductivity of ion-doped graphite/polyethersulphone composites

The electrical conductivity of polyethersulphone (PES) insulating polymer was improved by incorporation of electrically conductive graphite and ions. An initial conducting pathway of the PES/graphite composites was formed at lower than 3 wt.% of the filler content. LiCl was found to be an effective dopant for the improvement of the electrical conductivities of the PES/graphite composites. By doping with 0.06 wt.% of LiCl the electrical conductivity was enhanced by two orders of magnitude. The enhancement resulted from intercalation of Li⁺ ions into interlayer spaces of the graphite. Upon intercalation, an acceptor GIC, Li-GIC, was consequently formed. The stability of the improved electrical conductivities of the composites contributed with doped-ions was assessed. The electrical conductivity of both un-doped and doped graphite/PES composites slightly increased with increasing temperature and slightly decreased by physical ageing. The enhancement of the electrical conductivities by doping ions was stable at the high temperatures.     

Multifunctional properties of high volume fraction aligned carbon nanotube polymer composites with controlled morphology

Advanced composites, such as those used in aerospace applications, employ a high volume fraction of aligned stiff fibers embedded in high-performance polymers. Unlike advanced composites, polymer nanocomposites (PNCs) employ low volume fraction filler-like concepts with randomly-oriented and poorly controlled morphologies due to difficult issues such as dispersion and alignment of the nanostructures. Here, novel fabrication techniques yield controlled-morphology aligned carbon nanotube (CNT) composites with measured non-isotropic properties and trends consistent with standard composites theories. Modulus and electrical conductivity are maximal along the CNT axis, and are the highest reported in the literature due to the continuous aligned-CNTs and use of an unmodified aerospace-grade structural epoxy. Rule-of-mixtures predictions are brought into agreement with the measured moduli when CNT waviness is incorporated. Waviness yields a large (10×) reduction in modulus, and therefore control of CNT collimation is seen as the primary limiting factor in CNT reinforcement of composites for stiffness. Anisotropic electron transport (conductivity and current-carrying capacity) follows expected trends, with enhanced conductivity and Joule heating observed at high current densities.     

Highly strong and conductive carbon nanotube/cellulose composite paper

Carbon nanotube (CNT)/cellulose composite materials were fabricated in a paper making process optimized for a CNT network to form on the cellulose fibers. The measured electric conductivity was from 0.05 to 671 S/m for 0.5–16.7 wt.% CNT content, higher than that for other polymer composites. The real permittivities were the highest in the microwave region. The unique CNT network structure is thought to be the reason for these high conductivity and permittivity values. Compared to other carbon materials, our carbon CNT/cellulose composite material had improved parameters without decreased mechanical strength. The near-field electromagnetic shielding effectiveness (EMI SE) measured by a microstrip line method depended on the sheet conductivity and qualitatively matched the results of electromagnetic field simulations using a finite-difference time-domain simulator. A high near-field EMI SE of 50-dB was achieved in the 5–10 GHz frequency region with 4.8 wt.% composite paper. The far-field EMI SE was measured by a free space method. Fairly good agreement was obtained between the measured and calculated results. Approximately 10 wt.% CNT is required to achieve composite paper with 20-dB far-field EMI SE.     

RTM processing and electrical performance of carbon nanotube modified epoxy/fibre composites

This investigation focuses on nanoparticle filtration in the processing of multiscale carbon and glass fibre composites via resin transfer moulding. Surface modified and unmodified carbon nanotubes (CNTs) were incorporated into a commercial epoxy resin. The dispersion quality was evaluated using electrical measurements of the liquid suspensions. The manufacturing process was adapted to the challenges posed by the modified rheological behaviour of the CNT loaded resin. Nanoparticle filtration was observed; with some of the unmodified systems following so called ‘cake filtration’ behaviour. This resulted in nonlinear flow behaviour that deviated from the ideal response observed in RTM filling in conventional composites. The electrical conductivity of relatively high fibre volume fraction multiscale carbon and glass laminates increased by less than an order of magnitude with the addition of the nanotubes.     

A novel approach to fabricate high volume fraction nanocomposites with long aligned carbon nanotubes

Conventional micro-fiber-reinforced composites provide insight into critical structural features needed for obtaining maximum composite strength and stiffness: the reinforcements should be long, well aligned in a unidirectional orientation, and should have a high reinforcement volume fraction. It has long been a challenge for researchers to process CNT composites with such structural features. Here we report a method to quickly produce macroscopic CNT composites with a high volume fraction of millimeter long, well aligned CNTs. Specifically, we use the novel method, shear pressing, to process tall, vertically aligned CNT arrays into dense aligned CNT preforms, which are subsequently processed into composites. Alignment was confirmed through SEM analysis while a CNT volume fraction in the composites was calculated to be 27%, based on thermogravimetric analysis data. Tensile testing of the preforms and composites showed promising mechanical properties with tensile strengths reaching 400 MPa.     

The effects of carbon nanotubes on mechanical and thermal properties of woven glass fibre reinforced polyamide-6 nanocomposites

This paper presents a preliminary investigation on the effects of incorporating carbon nanotubes (CNT) into polyamide-6 (PA6) on mechanical, thermal properties and fire performance of woven glass reinforced CNT/PA6 nanocomposite laminates. The samples were characterized by tensile and flexural tests, thermal gravimetric analysis (TGA), heat distortion temperature (HDT) measurements, thermal conductivity and cone calorimeter tests. Incorporation of up to 2 wt% CNT in CNT/PA6/GF laminates improved the flexural stress of the laminates up to 36%, the thermal conductivity by approximately 42% and the ignition time and peak HRR time was delayed by approximately 31% and 118%, respectively.     

Hybrid multi-scale epoxy composite made of conventional carbon fiber fabrics with interlaminar regions containing electrospun carbon nanofiber mats

Herein we report the development and evaluation of hybrid multi-scale epoxy composite made of conventional carbon fiber fabrics with interlaminar regions containing mats of electrospun carbon nanofibers (ECNs). The results indicated that (1) the interlaminar shear strength and flexural properties of hybrid multi-scale composite were substantially higher than those of control/comparison composite without ECNs; in particular, the interlaminar shear strength was higher by ∼86%; and (2) the electrical conductivities in both in-plane and out-of-plane directions were enhanced through incorporation of ECNs, while the enhancement of out-of-plane conductivity (∼150%) was much larger than that of in-plane conductivity (∼20%). To validate the data reduction procedure, a new shear stress formula was formulated for composite laminates, which took into account the effect of layup and inter-layers. The study suggested that ECNs could be utilized for the development of high-performance composites, particularly with the improved out-of-plan properties (e.g., interlaminar shear strength).     

Mechanical,electrical and thermal properties of aligned carbon nanotube/polyimide composites

Carbon nanotubes (CNTs) have high strength and modulus, large aspect ratio, and good electrical and thermal conductivities, which make them attractive for fabricating composite. The poly(biphenyl dianhydride-p-phenylenediamine) (BPDA/PDA) polyimide has good mechanical and thermal performances and is herein used as matrix in unidirectional carbon nanotube composites for the first time. The strength and modulus of the composite increase by 2.73 and 12 times over pure BPDA–PDA polyimide, while its electrical conductivity reaches to 183 S/cm, which is 10¹⁸ times over pure polyimide. The composite has excellent high temperature resistance, and its thermal conductivity is beyond what has been achieved in previous studies. The improved properties of the composites are due to the long CNT length, high level of CNT alignment, high CNT volume fraction and good CNT dispersion in polyimide matrix. The composite is promising for applications that require high strength, lightweight, or high electrical and thermal conductivities.     

Synthesis,microstructure and mechanical properties of Yttria Stabilized Zirconia (3YTZP) – Multi-Walled Nanotube (MWNTs) nanocomposite by direct in-situ growth of MWNTs on Zirconia particles

In this research, Yttria Stabilized Zirconia (3YTZP) – carbon nanotube (CNT) composites are fabricated by direct in-situ growth of CNTs on the Zirconia particles, followed by densification via the Spark Plasma Sintering (SPS) technique. Scanning electron microscopy analysis of the 3YTZP-CNT powders shows uniform distribution of CNTs without the formation of agglomerates frequently seen with the traditional ex-situ mixing of CNTs in ceramic compositions. The samples were sintered to nearly 100% theoretical density and with a finer grain size microstructure. High Resolution Transmission Electron Microscopy (HRTEM) and Raman Spectroscopy confirm CNT retention in the sintered nanocomposites up to 1600 °C. The flexural strength increases from ∼260 MPa for samples without CNTs sintered at 1600 °C to ∼312 MPa for samples with ∼4 wt.% CNTs sintered at the same temperature. A corresponding increase in the indentation fracture toughness is also observed for samples with ∼4 wt.% CNTs sintered at 1600 °C as compared to samples sintered at the same temperature without CNTs.     

Synergetic effect of conducting polymer composites reinforced E-glass fabric for the control of electromagnetic radiations

The use of fibril materials as substrate for reinforcing polymers has wide industrial applications. In this article, we discuss polyaniline and polypyrrole as conducting polymers to provide electronic conductivity in E-glass fabric reinforced conducting composite with varied degree of composition and conductivity using industrially important polymers polymethylmethacrylate and polyvinyl chloride as a host matrix. Aromatic sulphonic acids such as PXSA, OXSA, PSA, PDSA, RDSA, OCPSA and MCSA were used as a dopant. The influence of the aromatic ring substituents in these dopants over the conductivity and processibility due to various interactions has been studied. The study shows that due to bulk nature of conductivity, shielding effectiveness (SE) increases with increase in conductivity and thickness of a composite. The test samples were characterized by conductivity and electromagnetic shielding effectiveness (EMI SE). The electromagnetic shielding effectiveness was measured by co-axial transmission line method in the frequency range of 0.01–1000 MHz. These composites with both side shielded by polypyrrole offered a uniform shielding effectiveness of 69 dB.     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

Hybrid network structure and thermal conductive properties in poly(vinylidene fluoride) composites based on carbon nanotubes and graphene nanoplatelets

A small quantity of carbon nanotubes (CNTs) and graphene nanoplatelets (GNPs) were introduced into the poly(vinylidene fluoride) (PVDF)/GNP and PVDF/CNT composites, respectively, to prepare the corresponding ternary PVDF/CNT/GNP and PVDF/GNP/CNT composites. The results demonstrated that adding CNTs into the PVDF/GNP composites greatly promoted the formation of the hybrid network structure of fillers. This was much different from the scenario that adding GNPs into the PVDF/CNT composites. GNPs and CNTs exhibited excellent nucleation effects for the crystallization of PVDF matrix; however, the variation of the PVDF crystallinity was small. Adding CNTs into the PVDF/GNP composites greatly enhanced the electrical conductivity of the PVDF/CNT/GNP composites. This was also different from the scenario of the PVDF/GNP/CNT composites. Furthermore, the PVDF/CNT/GNP composites exhibit higher thermal conductivity and higher synergistic efficiency compared with the PVDF/GNP/CNT composites. The conductive mechanisms and the synergistic effects of the ternary composites were then analyzed.     

Complementary percolation characteristics of carbon fillers based electrically percolative thermoplastic elastomer composites

Electrically percolative composites of thermoplastic elastomers (TPE) filled with different concentrations of carbon nanotubes (CNT), carbon black (CB) and (CNT–CB) hybrid fillers were fabricated by melt blending. The effects of filler type and composition on the electrical properties of the percolative TPE composites were studied. Percolation threshold for CB-, CNT- and (CNT–CB)-based composites was found to be 0.06, 0.07 and 0.07 volume fraction respectively. Compared to CB-based composites and earlier reported results, CNT- and (CNT–CB)-based ones revealed an unexpectedly high percolation threshold, which otherwise considered an unwelcome phenomenon, lead to distinct and rare percolation characteristics of CNT filled percolative composites like per-percolation conductivity and a relatively steep percolation curves. CB-based composites showed a comparatively sharp insulator–conductor transition curve complementing the percolation characteristics CNT- and (CNT–CB)-based composites. Percolation threshold conductivity of the fillers was in the order of CB > CNT > (CNT–CB), while maximum attained conductivities followed the order of CNT > (CNT–CB) > CB. Conductivity order of fillers not only denied much reported synergic effect in (CNT–CB) filler but also highlighted the effect of percolation characteristics on the outcome of conductivity values. Results obtained were of theoretical as well as practical importance and were explained in the context of filler morphology and different dispersion characteristics of the carbon based fillers.     

Elevated temperature tensile properties and thermal expansion of CNT/2009Al composites

1.5 vol.% and 4.5 vol.% carbon nanotubes reinforced 2009Al (CNT/2009Al) composites with homogeneously dispersed CNTs and refined matrix grains, were fabricated using powder metallurgy (PM) followed by 4-pass friction stir processing (FSP). Tensile properties of the composites between 293 and 573 K and the coefficient of thermal expansion (CTE) from 293 to 473 K were tested. It was indicated that load transfer mechanism still takes effect at temperatures elevated up to 573 K, thus the yield strength of the 1.5 vol.% CNT/2009Al composite at 423–573 K, was enhanced compared with the 2009Al matrix. However, for the 4.5 vol.% CNT/2009Al composite, the yield strength at 573 K was even lower than that for the matrix, due to the quicker softening of ultrafine-grained matrix. Compared with the 2009Al matrix, the CTEs of the composites were greatly reduced for the zero thermal expansion and high modulus of the CNTs and could be well predicted by the Schapery’s model.     

Evaluation and modelling of electrically conductive polymer nanocomposites with carbon nanotube networks

Superior electrical, thermal, and mechanical properties of carbon nanotubes (CNTs) have made them effective filler for multifunctional polymer nanocomposites (PNCs). In particular, electrically conductive PNCs filled with CNTs have been researched extensively. These studies aimed to increase the PNCs' electrical conductivity (σ) and to minimize the percolation thresholds (ϕ_c). In this work, we have developed an improved model to describe the CNT networks and thereby evaluate the PNCs' ϕ_c and σ. The new model accounts for the electrical conductance contributed by the continued CNT network across the boundary of adjacent representative volume elements. It more realistically represents the interconnectivity among CNTs and enhances the evaluation of the structure-to-property relationship of PNCs' σ.