Silver nanowire layer-by-layer films as substrates for surface-enhanced Raman scattering

In this paper, the fabrication of highly stable, surface-enhanced Raman scattering (SERS) active dendrimer/silver nanowire layer-by-layer (LBL) films is reported. Ag nanowires, approximately 100 nm in diameter, were produced in solution and transferred, using the LBL technique, onto a single fifth-generation DAB-Am dendrimer layer on a glass substrate. The Ag nanowires, and the resulting LBL films were characterized using UV-visible surface plasmon absorbance, while the LBL films were further characterized by atomic force microscopy measurements and surface-enhanced Raman and resonance Raman scattering of several analytes. The dendrimer was found to effectively immobilize the Ag nanowires with increased control over spacing and aggregation of the particles. These films are shown to be excellent substrates for SERS/SERRS measurements, demonstrating significant enhancement, and trace detection capability. Several trial analytes were tested using a variety of excitation energies, and results confirmed effective enhancement of Raman signals throughout the visible range (442-785 nm) with different molecules. Analytes were deposited onto the enhancing Ag nanowire LBL films surface using both casting and Langmuir-Blodgett monolayer transferring techniques.     

Silver clusters onto nanosized colloidal silica as novel surface-enhanced Raman scattering active substrates

A new method is proposed for obtaining surface-enhanced Raman scattering (SERS)-active substrates by photochemical reduction of silver nitrate onto colloidal silica. Transmission electron microscopy (TEM) and UV-visible absorption spectroscopy are employed to investigate the nanoscale structure of the materials. High quality SERS spectra are obtained from different organic ligands to check the efficiency of these substrates. A marked stability of the colloidal suspension is ensured by the scarce tendency of the Ag-doped silica particles to aggregate by either aging or adsorption of ligand.     

Silver-embedded zeolite crystals as substrates for surface-enhanced Raman scattering

This paper reports the preparation of a type of Ag-embedded zeolite crystals as surface-enhanced Raman spectroscopy (SERS) substrates by chemical reduction of Ag⁺-exchanged ZSM-5. Ag⁺ ions were loaded into the zeolite framework by ion exchange. Then the exchanged-Ag⁺ ions were reduced and metallic silver clusters formed inside the zeolite channel. The resulting Ag-embedded zeolite crystals are characterized by using a number of techniques including X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy to confirm silver formed inside the crystal channel. The fabricated Ag-embedded ZSM-5 zeolite substrates displayed strong and reproducible SERS activity for different Raman probe molecules such as Tris(2,2′-bipyridyl) ruthenium(II) chloride (RuBpy) and rhodamine 6G (R6G). Since silver embedded into the zeolite channel without changing the crystal surface property, the Ag–ZSM-5 zeolite crystal can be used to prepare different SERS-active substrate (SERS-tags), in which different probe molecules may be detected. Such Ag-embedded zeolite substrate would be useful in chemical and biological sensing and in the development of SERS-based analytical devices.     

Novel Ag-Cu substrates for surface-enhanced Raman scattering

Ag dendrites were deposited on rough Cu plate by a simple galvanic displacement process between Ag ion and Cu under room temperature. Surface-enhanced Raman scattering (SERS) performances have been studied using Rhodamine 6G (R6G) probe molecules on this kind of Ag-Cu substrates. The high SERS enhancements are attributed to the highly branched Ag dendritic nanostructures and Ag nanoparticles formed on the trunks, branches, and even leaves.     

Silver-coated zeolite crystal films as surface-enhanced Raman scattering substrates

Silver-coated zeolite A and zeolite NaX crystal films prepared by vacuum deposition were investigated as surface-enhanced Raman scattering (SERS) substrates. The substrates were active for the enhancement of Raman scattering from uranyl ions. A detection limit of 10(-5) M for uranyl was obtained using silver-coated zeolite A films. One advantage of these zeolite-based substrates is that the negatively charged microporous framework provides the selectivity for adsorption based on static electric charges. The SERS effects of positively charged uranyl ions and neutrally charged benzoic acid were compared. For the zeolite A substrate, there was a 100-times-greater sensitivity.     

Silver nanoparticles deposited on porous silicon as a surface-enhanced Raman scattering (SERS) active substrate

Silver nanoparticles were deposited spontaneously from their aqueous solution on a porous silicon (PS) layer. The PS acts both as a reducing agent and as the substrate on which the nanoparticles nucleate. At higher silver ion concentrations, layers of nanoparticle aggregates were formed on the PS surface. The morphology of the metallic layers and their SERS activity were influenced by the concentrations of the silver ion solutions used for deposition. Raman measurements of rhodamine 6G (R6G) and crystal violet (CV) adsorbed on these surfaces showed remarkable enhancement of up to about 10 orders of magnitude.     

A nanoforest structure for practical surface-enhanced Raman scattering substrates

A nanoforest structure for surface-enhanced Raman scattering (SERS) active substrates is fabricated and analyzed. The detailed morphology of the resulting structure can be easily controlled by modifying the process parameters such as initial gold layer thickness and etching time. The applicability of the nanoforest substrate as a label-free SERS immunosensor is demonstrated using influenza A virus subtype H1N1. Selective binding of the H1N1 surface antigen and the anti-H1 antibody is directly detected by the SERS signal differences. Simple fabrication and high throughput with strong in-plane hot-spots imply that the nanoforest structure can be a practical sensing component of a chip-based SERS sensing system.     

Silver nanoparticle-doped polyvinyl alcohol coating as a medium for surface-enhanced Raman scattering analysis

A simple polymer substrate for inducing Surface-Enhanced Raman Scattering (SERS) has been investigated. This SERS substrate consists of a solid support, such as a glass slide covered with polyvinyl alcohol (PVA) impregnated with fine silver nanoparticles. The preparation simply involves mixing aqueous PVA polymer with solid AgNO3 to produce a solution that can be easily spin coated on the glass substrate and dried to obtain a hard translucent coating. Aqueous solution of FeSO4.7H2O was used to reduce Ag+ ions to silver nanoparticles. The effects of various experimental conditions of sample preparation were investigated in order to improve the Raman enhancement efficiency of the substrate. The overall substrate performance was evaluated with the use of biologically important compounds: benzoic acid, p-amino benzoic acid, pyridine and dopamine. The spectral features of these compounds closely matched with those reported in literature. The use of the polymer matrix made the SERS substrate resistant to scratching, therefore, improving it to be more suitable for field applications. The hydrophilic nature of the polymer provides additional advantages for probing biological samples. The shelf-life of the dried, unreduced substrates is at least one month.     

Self-assembly nanoparticle based tripetaloid structure arrays as surface-enhanced Raman scattering substrates

This paper reports a novel highly ordered tripetaloid structure array (TPSA) which performs very well as an active surface-enhanced Raman scattering (SERS) substrate. The TPSA is easily fabricated by anisotropic etching of a self-assembly silica-nanoparticle bilayer and a subsequent metal deposition step, with notable uniformity and reproducibility. Electromagnetic simulation indicates that the narrow inter-gaps and edge protrusions in the TPSA act as hot spots. In addition, the peak electromagnetic field intensity in the inter-gaps changes slightly and periodically as the polarization of the incident light varies from 0°?to 360°. SERS experiments show that the SERS enhancement factor (EF) of a Au-film-covered TPSA is 12 times higher than that of regular Au-film-over-nanoparticles, and not sensitive to the polarization of the incident light. The spatially averaged EF of the TPSA is as high as 5.7?×?10(6), and the local EF of its hot spots is much higher.     

Silver nanorod arrays as a surface-enhanced Raman scattering substrate for foodborne pathogenic bacteria detection

Surface-enhanced Raman scattering (SERS) using novel silver nanorod array substrates has been used for the detection of pathogenic bacteria. The substrate consists of a base layer of 500 nm silver film on a glass slide and a layer of silver nanorod array with a length of approximately 1 microm produced by the oblique angle deposition method at a vapor incident angle of 86 degrees . Spectra from whole cell bacteria, Generic Escherichia coli, E. coli O157:H7, E. coli DH 5alpha, Staphylococcus aureus, S. epidermidis, and Salmonella typhimurium, and bacteria mixtures have been obtained. This SERS active substrate can detect spectral differences between Gram types, different species, their mixture, and strains. Principal component analysis (PCA) has been applied to classify the spectra. Viable and nonviable cells have also been examined, and significantly reduced SERS responses were observed for nonviable cells. SERS detection of bacteria at the single cell level, excited at low incident laser power (12 micro W) and short collection time (10 s), has also been demonstrated. These results indicate that the SERS-active silver nanorod array substrate is a potential analytical sensor for rapid identification of microorganisms with a minimum of sample preparation.     

High pressure Raman scattering of silicon nanowires

We study the high pressure response, up to 8 GPa, of silicon nanowires (SiNWs) with ～ 15 nm diameter, by Raman spectroscopy. The first order Raman peak shows a superlinear trend, more pronounced compared to bulk Si. Combining transmission electron microscopy and Raman measurements we estimate the SiNWs' bulk modulus and the Grüneisen parameters. We detect an increase of Raman linewidth at ～ 4 GPa, and assign it to pressure induced activation of a decay process into LO and TA phonons. This pressure is smaller compared to the ～ 7 GPa reported for bulk Si. We do not observe evidence of phase transitions, such as discontinuities or change in the pressure slopes, in the investigated pressure range.     

Preparation of tetrapod-like nanostructure array and used as the surface-enhanced Raman scattering substrates

Nanostructure surface composed of tetrapod-like structure with the period of about 2 microm has been made by simple nanoprinted method, the collodion was poured directly on the surface of the template and tore off after it became solidification, and then a layer of gold was sputtered on the collodion surface. The electric field distributions of the tetrapod-like structure with different size and period have been simulated using finite element method. Surface-enhanced Raman spectra mapping image gotten from the substrates illustrated the uniform enhancement property of it. The diluted aqueous solution of Rhodamine 6G (50 nM) was used to test the enhanced property of substrates for trace detection and good quality spectra has been gotten. The spectra of melamine with the concentration of 1 mg/L (7.9 microM) on the substrates were gotten to show the enhanced ability for molecule with small Raman scattering cross section.     

Integrate silver colloids with silicon nanowire arrays for surface-enhanced Raman scattering

A facile method to prepare uniform and reproducible surface-enhanced Raman scattering (SERS) substrates is presented. Quasi-spherical silver colloids prepared by microwave heating and wafer-scale uniform silicon nanowire (SiNW) arrays fabricated via wet chemical etching were united together as SERS substrates. The novel SERS substrates displayed stronger Raman enhancement than conventional silver colloids as well as outstanding uniformity and reproducibility in our experiments. In addition, it was found that the cross section of SiNW arrays possessed stronger enhancement activity than the front side. The enhancement effects of two adjacent SiNWs (as a simplification of SiNW arrays) were evaluated by the finite difference time domain (FDTD) method.     

Silver nanocrystals of various morphologies deposited on silicon wafer and their applications in ultrasensitive surface-enhanced Raman scattering

Silver nanostructures with dendritic, flower-like and irregular morphologies were controllably deposited on a silicon substrate in an aqueous hydrogen fluoride solution at room temperature. The morphology of the Ag nanostructures changed from dendritic to urchin-like, flowerlike and pinecone-like with increasing the concentration of polyvinyl pyrrolidone (MW = 55,000) from 2 to 10 mM. The Ag nanostructures were characterized by transmission electron microscopy, high-resolution transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray, and X-ray diffraction. Through a series of time-dependent morphological evolution studies, the growth processes of Ag nanostructures have been systematically investigated and the corresponding growth mechanisms have been discussed. In addition, the morphology-dependent surface-enhanced Raman scattering of as-synthesized Ag nanostructures were investigated. The results indicated that flower-like Ag nanostructure had the highest activity than the other Ag nanostructures for Rhodamine 6G probe molecules.     

Gold/palladium and silver/palladium colloids as novel metallic substrates for surface-enhanced Raman scattering

New surface-enhanced Raman scattering (SERS) substrates, composed of gold or silver colloidal nanoparticles doped with palladium, were prepared. These novel colloids are stable and maintain a satisfactory SERS efficiency, even after long aging. The interest in doping the coinage metal nanoparticles with palladium is due to the well-known catalytic activity of this metal. Transmission electron microscopy (TEM) and ultraviolet-visible absorption spectroscopy were used to characterize the shape and size of the metal particles. It was found that these bimetallic colloidal nanoparticles have a core-shell structure, with gold or silver coated with palladium clusters.     

Plasma reduction of silver compounds for fabrication of surface-enhanced Raman scattering substrates

Several silver compounds were reduced by low-pressure air plasma to produce porous nanostructured surfaces as surface-enhanced Raman scattering (SERS) substrates. This method is advantageous because substrates are easy to prepare and the silver metal surface is inherently clean without spectroscopic background. Silver compounds were melted into 1-2 mm slugs on quartz slides and plasma treated for different lengths of time. Silver chloride was found to be the best compound to make reproducible and stable SERS substrates. SERS activity of the substrates was tested using L-tryptophan, 4-mercaptobenzoic acid, and adenine.     

New strategy for ready application of surface-enhanced resonance Raman scattering/surface-enhanced Raman scattering to chemical analysis of organic films on dielectric substrates

Dropping of appropriately concentrated AgNO3 and NaBH4 solutions, as well as laser-ablated Ag sols, onto organic molecules results in the formation of aggregated Ag nanoparticles that can induce surface-enhanced Raman scattering (SERS) for the molecules. The addition of flocculating agents such as alkali halides can further increase the Raman signals. We demonstrate in this work that Raman spectra can be obtained even for 0.01 monolayers of R6G on Si simply by spreading silver nanoparticles and/or fabricating Ag nanoparticles and nanoaggregates at the gaps and vacant sites of R6G molecules. The application prospect of the present methodology is extremely high, not only because of its simplicity but also because of the fact that the observation of vibrational spectra is one of the most incisive methods for understanding the chemical and physical phenomena on a variety of surfaces.     

A novel method for fabricating the surface-enhanced Raman scattering substrates and its enhanced properties

We have got large area surface-enhanced Raman scattering (SERS) substrates with uniform high enhancement factors by the so-called moulage method for the first time. A silver film (99.99%) with several millimeters thickness was thermally evaporated on the porous anodic alumina templates and the SERS substrate was got after moving off the templates. Surface-enhanced Raman scattering spectra of pyridine (0.01 Mol/L) were measured under 632.8 nm excitation. The experimental enhancement factors were more than 10(5) and S/N(p-p) around 100 was obtained. We have compared the SERS spectra of pyridine collected from different locations on the same SERS substrate and different substrates, which illustrate the well uniform enhance properties and the reproducibility of this method, respectively. The comparison of the SERS spectra, obtained from the SERS substrates and Ag film evaporated directly on glass slide, have proved that the electromagnetic coupling between two adjacent nanoparticles was important to the SERS effect. We also used rhodamine 6G as the probe molecules and found that the different molecules were very sensitive to the morphology of the SERS substrates.     

Enhanced first-order Raman scattering from arrays of vertical silicon nanowires

Vertical ordered silicon nanowire arrays with diameters ranging from 30 to 60 nm are fabricated and display enhanced Raman scattering. The first-order 520 cm(-1) phonon mode shows no significant shift or peak broadening with increasing laser power, suggesting that the excellent defect-free diamond crystalline structure and thermal properties of bulk silicon are maintained. The Raman enhancement per unit volume of the first-order phonon peak increases with increasing nanowire diameter, and has maximum enhancement factors of 7.1 and 70 when compared to the original silicon on insulator (SOI) and bulk silicon wafers, respectively. For the array with 60 nm diameter nanowires, the total Raman intensity is larger than that of the SOI wafer. The results are understood using a model based on the confinement of light and are supported by finite difference time domain (FDTD) simulations.