Phase transition and piezoelectric properties of K0.48Na0.52NbO3-LiTa0.5Nb0.5O3-NaNbO3 lead-free ceramics

Plate-like NaNbO₃ (NN) particles were used as the raw material to fabricate (1 − x)[0.93 K_0.48Na_0.52Nb O₃-0.07Li(Ta_0.5Nb_0.5)O₃]-xNaNbO₃ lead-free piezoelectric ceramics using a conventional ceramic process. The effects of NN on the crystal structure and piezoelectric properties of the ceramics were investigated. The results of X-ray diffraction suggest that the perovskite phase coexists with the K₃Li₂Nb₅O₁₅ phase, and the tilting of the oxygen octahedron is probably responsible for the evolution of the tungsten-bronze-typed K₃Li₂Nb₅O₁₅ phase. The Curie temperature (T_C) is shifted to lower temperature with increasing NN content. (1 − x)[0.93 K_0.48Na_0.52NbO₃-0.07Li(Ta_0.5Nb_0.5)O₃]-xNaNbO₃ ceramics show obvious dielectric relaxor characteristics for x > 0.03, and the relaxor behavior of ceramics is strengthened by increasing NN content. Both the electromechanical coupling factor (k_p) and the piezoelectric constant (d₃₃) decrease with increasing amounts of NN. 0.01-0.03 mol of plate-like NaNbO₃ in 0.93 K_0.48Na_0.52NbO₃-0.07Li(Ta_0.5Nb_0.5)O₃ gives the optimum content for preparing textured ceramics by the RTGG method.     

Enhanced piezoelectric properties of Ta substituted-(K0.5Na0.5)NbO3 films: A candidate for lead-free piezoelectric thin films

Piezoelectric (K_0.5Na_0.5)NbO₃ (KNN) and (K_0.5Na_0.5)(Nb_0.7Ta_0.3)O₃ (KNNT) thin films were prepared via chemical solution deposition. An analysis of X-ray diffraction revealed that Ta⁵⁺ diffuses into the KNN to form a single perovskite structure. Compared to KNN films, KNNT films exhibited a low leakage current density due to their fine-grain nonporous structures. The partial substitution of Ta⁵⁺ for the B-site ion Nb⁵⁺ in the KNNT films decreased the Curie temperature (T_C). This in turn led to the existence of a polymorphic phase transition near room temperature and further improvement in the piezoelectric properties. Lead-free KNNT films exhibited a well-saturated piezoelectric hysteresis loop with a effective piezoelectric coefficient (d_33,eff) value of 61 pm/V, comparable to that of PZT thin films.     

Effect of addition of Ba(W0.5Cu0.5)O3 in Pb(Mg1/3Nb2/3)O3-Pb(Zn1/3Nb2/3)O3-Pb(Zr0.52Ti0.48)O3 ceramics on the sintering temperature, electrical properties and phase transition

In this work, we report on the Pb(Mg_1/3Nb_2/3)O₃-Pb(Zn_1/3Nb_2/3)O₃-Pb(Zr_0.52Ti_0.48)O₃ (PMN-PZN-PZT) ceramics with Ba(W_0.5Cu_0.5)O₃ as the sintering aid that was manufactured in order to develop the low-temperature sintering materials for piezoelectric device applications. The phase transition, microstructure, dielectric, piezoelectric properties, and the temperature stability of the ceramics were investigated. The results showed that the addition of Ba(W_0.5Cu_0.5)O₃ significantly improved the sintering temperature of PMN-PZN-PZT ceramics and could lower the sintering temperature from 1005 to 920 °C. Besides, the obtained Ba(W_0.5Cu_0.5)O₃-doped ceramics sintered at 920 °C have optimized electrical properties, which are listed as follows: (K_p = 0.63, Q_m = 1415 and d₃₃ = 351 pC/N), and high depolarization temperature above 320 °C. These results indicated that this material was a promising candidate for high-power multilayer piezoelectric device applications.     

Phase transition and electrical properties of (1 − x)K0.02Na0.98NbO3-xBaTiO3 ceramics

(1 − x)K_0.02Na_0.98NbO₃-xBaTiO₃ ceramics were prepared by the solid state reaction method, and their electrical properties were investigated. The samples showed crystal structure changing from monoclinic to orthorhombic, and then to tetragonal, with an increase in BaTiO₃ content. The addition of BaTiO₃ markedly enhanced ferroelectric and piezoelectric properties of K_0.02Na_0.98NbO₃ ceramics. Remnant polarization increased and coercive field decreased only in the samples with small amount of BaTiO₃. Piezoelectric properties were improved with the addition of BaTiO₃. The 0.9K_0.02Na_0.98NbO₃-0.1BaTiO₃ ceramics showed maximum piezoelectric constant (d₃₃ = 160 pC/N), which was even comparable with that of (1 − x)K_0.5Na_0.5NbO₃-xBaTiO₃ ceramics. Their good piezoelectric properties, along with a low ferroelectric-ferroelectric transition temperature (T_F-F), made the 0.9K_0.02Na_0.98NbO₃-0.1BaTiO₃ ceramics a potential candidate for lead-free piezoelectric applications.     

Piezoelectric and dielectric properties of Dy2O3-doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ + x wt% Dy₂O₃ with x = 0-0.3 ceramics were synthesized by conventional solid-state processes. The effects of Dy₂O₃ on the microstructure, the piezoelectric and dielectric properties were investigated. X-ray diffraction pattern confirmed that the coexistence of tetragonal and rhombohedral phases in the (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition was not changed by adding 0.05-0.3 wt% Dy₂O₃. SEM images indicate that all the ceramics have pore-free microstructures with high density, and that doping of Dy₂O₃ inhibits the grain growth of the ceramics. The addition of Dy₂O₃ shows the double effects on decreasing the piezoelectric and dielectric properties for 0 < x < 0.15 when Dy³⁺ ions substitute B-site Ti⁴⁺ ions, and increasing the properties for 0.15 < x < 0.3 when Dy³⁺ ions enters into A-site of the perovskite structure. The optimum electric properties of piezoelectric constant d₃₃ = 170 pC/N and the dielectric constant ?_r = 1900 (at a frequency of 1 kHz) are obtained at x = 0.3.     

Polymorphic phase transition-induced electrical behavior of BiCoO3-modified (K0.48Na0.52)NbO3 lead-free piezoelectric ceramics

(1 − x)(K_0.48Na_0.52)NbO₃-xBiCoO₃ [KNN-xBC] lead-free piezoelectric ceramics were prepared by the conventional solid-state sintering method. The effects of the BiCoO₃ addition on the phase structure, dielectric, piezoelectric and ferroelectric properties of KNN-xBC ceramics were systematically investigated. The polymorphic phase transition (PPT) from rhombohedral to orthorhombic phase around room temperature was identified in the composition range of 0.01 ≤ x ≤ 0.02, and the improved electrical properties were induced by this PPT. The KNN-0.01BC ceramics near PPT exhibit optimum electrical properties: d₃₃ ∼ 165 pC/N, k_p ∼ 0.40, P_r ∼ 31.0 μC/cm², and E_c ∼ 12.6 kV/cm. These results indicate that the enhanced piezoelectric properties for alkali niobate can be achieved by forming the coexistence of rhombohedral and orthorhombic phases.     

Preparation and electrical properties of Bi0.5Na0.5TiO3-BaTiO3-KNbO3 lead-free piezoelectric ceramics

Lead-free (1 − x)Bi_0.47Na_0.47Ba_0.06TiO₃-xKNbO₃ (BNBT-xKN, x = 0-0.08) ceramics were prepared by ordinary ceramic sintering technique. The piezoelectric, dielectric and ferroelectric properties of the ceramics are investigated and discussed. The results of X-ray diffraction (XRD) indicate that KNbO₃ (KN) has diffused into Bi_0.47Na_0.47Ba_0.06TiO₃ (BNBT) lattices to form a solid solution with a pure perovskite structure. Moderate additive of KN (x ≤ 0.02) in BNBT-xKN ceramics enhance their piezoelectric and ferroelectric properties. Three dielectric anomaly peaks are observed in BNBT-0.00KN, BNBT-0.01KN and BNBT-0.02KN ceramics. With the increment of KN in BNBT-xKN ceramics, the dielectric anomaly peaks shift to lower temperature. BNBT-0.01KN ceramic exhibits excellent piezoelectric properties and strong ferroelectricity: piezoelectric coefficient, d₃₃ = 195 pC/N; electromechanical coupling factor, k_t = 58.9 and k_p = 29.3%; mechanical quality factor, Q_m = 113; remnant polarization, P_r = 41.8 μC/cm²; coercive field, E_c = 19.5 kV/cm.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting Mg with Ni

The microwave dielectric properties of La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method at various sintering temperatures. The X-ray diffraction patterns of the La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.71 g/cm³, dielectric constant (?_r) of 20.19, quality factor (Q × f) of 74,600 GHz, and temperature coefficient of resonant frequency (τ_f) of −85 ppm/°C were obtained for La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

The temperature-dependent electrical properties of Bi0.5Na0.5TiO3-BaTiO3-Bi0.5K0.5TiO3 near the morphotropic phase boundary

Bi_0.5Na_0.5TiO₃-BaTiO₃-Bi_0.5K_0.5TiO₃ (BNT-BT-BKT) lead-free piezoceramics with compositions near the rhombohedral-tetragonal morphotropic phase boundary (MPB) were prepared and investigated. At room temperature, all ceramics show excellent electrical properties. In this study, the best properties were observed in 0.884BNT-0.036BT-0.08BKT, with the remnant polarization, bipolar total strain, unipolar strain, piezoelectric constant, and planar electromechanical coupling factor being 34.4 μC cm⁻², 0.25%, 0.15%, 122 pC N⁻¹, and 0.30, respectively. Detailed analysis of the temperature dependence of polarization-electric field (P-E) loops and bipolar/unipolar strain-electric field (S-E) curves of this composition revealed a ferroelectric-antiferroelectric phase transition around 100 °C. Around this temperature, there is a significant shape change in both P-E and S-E curves, accompanied by enhanced strain and decreased polarization; the largest recoverable strain reaches 0.42%. These results can be explained by the formation of antiferroelectric order and the contribution of field-induced antiferroelectric-ferroelectric phase transition to piezoelectric response. Our results indicate that BNT-BT-BKT lead-free piezoceramics can have excellent electrical properties in compositions near the MPB and also reveal some insight into the temperature dependence of the electrical performance with the MPB composition.     

Characterization of sol-gel synthesised lead-free (1 − x)Na0.5Bi0.5TiO3-xBaTiO3-based ceramics

The crystal structure, microstructure, dielectric and ferroelectric properties of (1 − x)Na_0.5Bi_0.5TiO₃-xBaTiO₃ ceramics with x = 0, 0.03, 0.05, 0.07 and 0.1 are investigated. A structural variation according to the system composition was investigated by X-ray diffraction (XRD) analyses. The results revealed that the synthesis temperature for pure perovskite phase powder prepared by the present sol-gel process is much lower (800 °C), and a rhombohedral-tetragonal morphotropic phase boundary (MPB) is found for x = 0.07 composition which showing the highest remanent polarization value and the smallest coercive field. The optimum dielectric and piezoelectric properties were found with the 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃ composition. The piezoelectric constant d₃₃ is 120 pC/N and good polarization behaviour was observed with remanent polarization (P_r) of 12.18 pC/cm², coercive field (E_c) of 2.11 kV/mm, and enhanced dielectric properties ?_r > 1500 at room temperature. The 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃-based ceramic is a promising lead-free piezoelectric candidate for applications in different devices.     

Microstructure, ferroelectric, and piezoelectric properties of (1 − x − y)Bi0.5Na0.5TiO3-xBaTiO3-yBi0.5Ag0.5TiO3 lead-free ceramics

Lead-free (1 − x − y)Bi_0.5Na_0.5TiO₃-xBaTiO₃-yBi_0.5Ag_0.5TiO₃ (BNT-BT-BAT-x/y, x = 0-0.10, y = 0-0.075) piezoelectric ceramics were synthesized by conventional oxide-mixed method. The microstructure, ferroelectric, and piezoelectric properties of the ceramics were investigated. Results show that a morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases of BNT-BT-BAT-x/0.04 ceramics is formed at x = 0.06-0.08. The addition of BAT has no obvious change on the crystal structure of BNT-BT ceramics while it causes the grain size of the ceramics to become more homogenous. Near the MPB, the ceramics with x = 0.06 and y = 0.05-0.06 possess optimum electrical properties: P_r ∼ 42.5 μC/cm², E_c ∼ 32.0 kV/cm, d₃₃ ∼ 172 pC/N, k_p ∼ 32.6%, and k_t ∼ 52.6%. The temperature dependences of k_p and polarization versus electric hysteresis loops reveal that the depolarization temperature (T_d) of BNT-BT-BAT-0.06/y ceramics decreases with increasing y. In addition, the polar and non-polar phases may coexist in the BNT-BT-BAT-x/y ceramics above T_d.     

Relationship between structure and properties in high-temperature Bi(Al0.5Fe0.5)O3-PbTiO3 piezoelectric ceramics

Ceramic samples of xBi(Al_0.5Fe_0.5)O₃-(1 − x)PbTiO₃ (BAF-PT, x = 0.05-0.5) solid solutions were fabricated using the conventional solid state reaction method. X-ray diffraction analysis revealed that all compositions can form single perovskite phase with tetragonal symmetry. The relationship between the tetragonal lattice parameters, tetragonality c/a, cell volume, and ferro-piezoelectric characterization as a function of x was systematically investigated. The BAF modification can effectively improve the poling condition at a proper BAF content. A combination of piezoelectric constant of d₃₃ (50-60 pC/N), electromechanical planar coupling coefficients of k_p (20.3-22.5%), and high Curie temperature T_c (>478 °C) suggested that BAF-PT could be a good candidate for high-temperature piezoelectric applications.     

Sol-gel auto-combustion synthesis of KxNa1-xNbO3 nanopowders and ceramics: Dielectric and piezoelectric properties

The K_xNa_1-xNbO₃ nanopowders with cubic-like morphology and an average size of about 50 nm were synthesized by sol-gel auto-combustion method. And then, the ceramics were prepared and the phase transition, microstructure and electrical properties of the K_xNa_1-xNbO₃ ceramics were investigated. Pure perovskite phases of the K_xNa_1-xNbO₃ ceramics were confirmed by XRD patterns and the K_0.50Na_0.50NbO₃ ceramics show the coexistence of orthorhombic and monoclinic structures. SEM micrographs show that all samples have bimodal grain size distributions and the number of the small grains decrease with increasing K⁺ content in the bimodal grain size distribution system. The K_0.50Na_0.50NbO₃ ceramics with the uniform grain size and the maximum density show excellent electrical properties with ε_r=467.40, tan δ=0.020, d₃₃=128 pC/N and k_p=0.32 at the room temperature, demonstrating that the properties of the K_0.50Na_0.50NbO₃ powers prepared by sol-gel auto-combustion are excellent and the ceramics are promising lead-free piezoelectric materials.     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

Study of structural, dielectric and electrical behavior of (1 − x)Ba(Fe0.5Nb0.5)O3-xSrTiO3 ceramics

Polycrystalline samples of BaFe_0.5Nb_0.5O₃ and (1 − x)Ba(Fe_0.5Nb_0.5)O₃-xSrTiO₃ [referred as BFN and BFN-ST respectively] (x = 0.00, 0.15 and 0.20) have been synthesized by a high-temperature solid-state reaction technique. The XRD patterns of the BFN and BFN-ST at room temperature show a monoclinic phase. The microstructure of the ceramics was examined by the scanning electron microscopy (SEM) and shows the polycrystalline nature of the samples with different grain sizes, which are inhomogeneously distributed through the sample surface. Detailed studies of dielectric and impedance properties of the materials in a wide range of frequency (100 Hz-5 MHz) and temperatures (30-270 °C) showed that properties are strongly temperature and frequency dependent. Complex Argand plane plot of ?″ against ?′, usually called Cole-Cole plots is used to check the polydispersive nature of relaxation phenomena in above mentioned compounds. Relaxation phenomena of non-Debye type have been observed in the BFN and BFN-ST ceramics, as confirmed by the Cole-Cole plots.     

Phase structure and electrical properties of (0.8 − x) BaTiO3-0.2Bi0.5Na0.5TiO3-xBaZrO3 lead-free piezoceramics

Lead-free piezoelectric ceramics (0.8 − x)BaTiO₃-0.2Bi_0.5Na_0.5TiO₃-xBaZrO₃ (BT-BNT-xBZ, 0 ≤ x ≤ 0.08) doped with 0.3 wt% Li₂CO₃ were prepared by conventional solid-state reaction method. With the Li₂CO₃ doping, all the ceramics can be well sintered at 1170-1210 °C. The phase structure, dielectric, ferroelectric and piezoelectric properties of the ceramics were investigated. Results show that a morphotropic phase boundary (MPB) between tetragonal and pseudocubic phases exists at x = 0.03-0.04. The addition of Zr can improve the piezoelectric properties of BT-BNT ceramics. Furthermore, a relaxor behavior is induced and the tetragonal-cubic phase transition shifts towards lower temperatures after the addition of Zr. The ceramics with x = 0.03 possess the optimum electrical properties: d₃₃ = 72 pC/N, k_p = 15.4%, ?_r = 661, P_r = 18.5 μC/cm², E_c = 34.1 kV/cm, T_c = 150 °C.     

Improving the piezoelectric thermal stability by tailoring phase transition behavior in the new (1 − x)[0.65PbMg1/3Nb2/3O3-0.35PbTiO3]-xBiZn1/2Ti1/2O3 perovskite solid solutions

The phase transition behavior and its effect on thermal stability of the piezoelectric properties of the (1 − x)[0.65PbMg_1/3Nb_2/3O₃-0.35PbTiO₃]-xBiZn_1/2Ti_1/2O₃ ceramics with 0 ≤ x ≤ 0.06 were investigated. The phase transition from the monoclinic to tetragonal phase was determined by the dielectric constant and elastic constant measurements. The temperature independent piezoelectric response with −d₃₁ = 188 pC/N was obtained from 175 to 337 K for the composition with x = 0.02. The enhanced thermal stability of piezoelectric response was achieved by shifting the monoclinic-tetragonal phase transition to the lower temperature.     

Role of alkali carbonate and salt in topochemical synthesis of K1/2Na1/2NbO3 and NaNbO3 templates

Since the properties of lead-free piezoelectric materials have thus far failed to meet those of lead-based materials, either chemical doping or morphological texturing should be employed to improve the piezoelectric properties of lead-free piezoelectric ceramics. The goal of this study was to synthesize plate-like K_1/2Na_1/2NbO₃ and NaNbO₃ particles, which are the most favorable templates for morphological texturing of K_1/2Na_1/2NbO₃ ceramics. To achieve this goal, Bi_2.5Na_3.5Nb₅O₁₈ precursors in a plate-like shape were first synthesized and subsequently converted into K_1/2Na_1/2NbO₃ or NaNbO₃ particles that retain the morphology of Bi_2.5Na_3.5Nb₅O₁₈. In this study, we found that sodium or potassium carbonate does not play a major role in converting the Bi_2.5Na_3.5Nb₅O₁₈ precursor to K_1/2Na_1/2NbO₃ or NaNbO₃, on the contrary to previous reports; however, the salt contributes to the conversion reaction. All synthesis processes have been performed via a molten salt method, and scanning electron microscopy, scanning probe microscopy, and inductively coupled plasma mass spectroscopy were used to characterize the synthesized K_1/2Na_1/2NbO₃ or NaNbO₃ templates.     

Effect of CuO on the sintering temperature and piezoelectric properties of MnO2-doped 0.75Pb(Zr0.47Ti0.53)O3-0.25Pb(Zn1/3Nb2/3)O3 ceramics

The sintering temperature of 0.75Pb(Zr_0.47Ti_0.53)O₃-0.25Pb(Zn_1/3Nb_2/3)O₃ ceramics containing 1.5 mol% MnO₂ was decreased from 930 to 850 °C with the addition of CuO. The CuO reacted with the PbO and formed a liquid phase during the sintering, which assisted the densification of the specimens. Most of the Cu²⁺ ions existed in the CuO second phase, thereby preventing any possible hardening effect from the Cu²⁺ ions. Variations of the k_p, Q_m, ?₃^T/?₀ and d₃₃ values with CuO were similar to that of the relative density. The specimen containing 0.5 mol% CuO sintered at 850 °C showed the good piezoelectric properties of k_p = 0.5, Q_m = 1000, ?₃^T/?₀ = 1750 and d₃₃ = 300 pC/N.