Using passive air samplers to assess urban-rural trends for persistent organic pollutants. 1. Polychlorinated biphenyls and organochlorine pesticides

Passive air samplers were used to investigate urban-rural differences of polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) over an integrated time period. Samplers consisting of polyurethane foam (PUF) disks and semi-permeable membrane devices (SPMDs) were housed in protective chambers and deployed at six sites for a 4 month duration in the summer of 2000. The sampling transect originated in downtown Toronto and extended approximately 75 km northward into a rural region. Results for the two types of samplers agreed well with one another. Higher blank levels were encountered for the SPMDs, especially for the OCPs, whereas blanks were very low for the PUF disks. Passive sampler-derived air concentrations were consistent with previous measurements of PCBs and OCPs in the region. The largest urban-rural gradient was observed for PCBs (approximately 5-10 times). Chlordanes also showed an urban-rural gradient, possibly reflecting past usage of chlordane on residential lawns and emissions from treated house foundations. Other OCPs exhibited a rural-urban gradient (dieldrin, endosulfan 1, and DDT isomers), which was attributed either to off-gassing from previously treated agricultural soils (dieldrin and DDTs) or to continued usage in agriculture (endosulfan 1). The results of this study demonstrated the feasibility of using such devices to determine air concentrations of persistent organic pollutants (POPs) and to assess their spatial distribution for time-integrated samples. Data such as this is essential for: model validation and for process research and addressing international monitoring strategies on POPs.     

Characterization and comparison of three passive air samplers for persistent organic pollutants

The accumulation of persistent organic pollutants by three passive sampling media--semipermeable membrane devices (SPMDs), polyurethane foam (PUF) disks, and an organic-rich soil--was investigated. The media were exposed to contaminated indoor air over a period of 450 days, and concentrations in the air and in the media were monitored for individual polychlorinated biphenyl (PCB) congeners and polychlorinated naphthalene homologue groups. Uptake was initially linear and governed by the surface area of the sampler and the boundary layer airside mass transfer coefficient (MTC). Mean values of the MTC were 0.13, 0.11, and 0.26 cm s-1 for SPMD, PUF, and soil, respectively. As the study progressed, equilibrium was established between ambient air and the passive sampling media for the lower molecular weight PCB congeners. This information was used to calculate passive sampler-air partition coefficients, KPSM-A. These were correlated to the octanol-air partition coefficient, and the resulting regressions were used to predict KPSM-A for the full suite of PCBs. Information on MTC, KPSM-A, surface area, and effective thickness of each sampler was used to estimate times to equilibrium for each medium. These ranged from tens of days for the lower molecular weight congeners to tens of years for the higher molecular weight PCBs. Expressions were also developed to relate the amount of chemical accumulated by the passive sampling media to average ambient air concentrations over the integration period of the sample.     

Field deployment of thin film passive air samplers for persistent organic pollutants: a study in the urban atmospheric boundary layer

This paper reports on the first field deployment of rapidly equilibrating thin-film passive air samplers under ambient conditions. The POlymer-coated Glass (POG) samplers have a coating of ethylene vinyl acetate (EVA) less than 1 microm thick applied to a glass surface. This can be dissolved off after exposure and prepared for the quantification of persistent organic pollutants (POPs) that have partitioned into the film during field exposure. In this study, POGs were deployed at various heights on the CN Tower in Toronto, Canada, to investigate the vertical distribution of selected compounds (PCBs, PAHs, organochlorine pesticides) in the atmospheric boundary layer of an urban area. The feasibility of the method to detect POPs from a few cubic meters of air was demonstrated, indicating the potential for rapid, low-volume sampling of air for ambient levels of POPs. PAH levels declined sharply with height, confirming ground-level emissions in urban areas as sources of these compounds; PCBs did the same, although less strongly. Different sampling events detected different vertical distributions of OC pesticides which could be related to local or distantsources, and variations in POPs on the samplers in these different events/heights demonstrate the dynamic nature of sources and atmospheric mixing of POPs.     

Passive and active air samplers as complementary methods for investigating persistent organic pollutants in the Great Lakes Basin

Data obtained using passive air samplers (PAS) are compared to active high-volume air sampling data in order to assess the feasibility of the PAS as a method, complementary to active high-volume air sampling (AAS), for monitoring levels of organochlorine (OC) pesticides, polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs) in the Laurentian Great Lakes. PAS were deployed at 15 of the Integrated Atmospheric Deposition Network (IADN) sites on a quarterly basis between July 2002 and June 2003, and PAS and AAS results are compared. Levels for the OC pesticides are typically highest in agricultural areas, with endosulfan I dominating air concentrations with values ranging between 40 and 1090 pg x m(-3), dieldrin values between 15 and 165 pg x m(-3), and gamma-HCH values between 13 and 100 pg x m(-3). alpha-HCH was seen to be relatively uniform across the Great Lakes Basin with values ranging between 15 and 73 pg x m(-3). Large urban centers, such as Chicago and Toronto, have the highest levels of PCBs and PBDEs that range between 400 and 1200 pg x m(-3) and 10 and 70 pg x m(-3), respectively. Comparison of the AAS and the PAS data collected during this study shows good agreement, within a factor of 2 or 3, suggesting that the two sample methods produce comparable results. It is suggested that PAS networks, while providing data that are different in nature from AAS, can provide a cost-effective and complementary approach for monitoring the spatial and temporal trends of persistent organic pollutants.     

Field validation of polyethylene passive air samplers for parent and alkylated PAHs in Alexandria, Egypt

Polyethylene samplers (PEs) were deployed at 11 locations in Alexandria, Egypt during summer and winter to test and characterize them as passive samplers for concentrations, sources, and seasonal variations of atmospheric concentrations of polycyclic aromatic hydrocarbons (PAHs). PE-air equilibrium was attained faster for a wider range of PAHs during the winter season possibly due to increased wind speeds. Calculated PE-air partitioning constants, K(PE-A), in our study [Log K(PE-A) = 0.9426 × Log K(OA) - 0.022 (n = 12, R(2) = 0.99, Std error = 0.053)] agreed with literature values within <46%. For parent (except naphthalene), mono- and dialkylated PAHs, active sampling based concentrations of PAHs were within an average factor of 1.4 (1.0-5.6) compared to the PE based values. For C(3-4) alkylated PAHs, K(PE-A) values were lower than predicted, on average by ~0.8 log units per carbon in the alkylation. Enthalpies of vaporization (ΔH(vap)) accurately corrected K(PE-A)s for temperature differences between winter and summer sampling. PAH profiles were dominated by naphthalene, phenanthrene, and alkylated phenanthrenes. Calculated diagnostic ratios indicated that PAHs originated mainly from vehicle emissions.     

Evaluation of passive samplers for assessment of community exposure to toxic air contaminants and related pollutants

The precision, accuracy, and sampling rates of Radiello and Ogawa passive samplers were evaluated in the laboratory using a flow-through chamber and under field conditions prior to their use in the 2007 Harbor Community Monitoring Study (HCMS), a saturation monitoring campaign in the communities adjacent to the Ports of Los Angeles and Long Beach. Passive methods included Radiello samplers for volatile organic compounds (benzene, toluene, ethylbenzene, xylenes, 1,3-butadiene), aldehydes (formaldehyde, acetaldehyde, acrolein) and hydrogen sulfide, and Ogawa samplers for nitrogen oxides and sulfur dioxide. Additional experiments were conducted to study the robustness of the passive sampling methods under variable ambient wind speed, sampling duration, and storage time before analysis. Our experimentally determined sampling rates were in agreement with the rates published by Radiello and Ogawa with the following exceptions: we observed a diffusion rate of 22.4 ± 0.1 mL/min for benzene and 37.4 ± 1.5 mL/min for ethylbenzene compared to the Radiello published values of 27.8 and 25.7 mL/min, respectively. With few exceptions, the passive monitoring methods measured one-week average ambient concentrations of selected pollutants with sensitivity and precision comparable to conventional monitoring methods averaged over the same period. Radiello Carbograph 4 VOC sampler is not suitable for the collection of 1,3-butadiene due to backdiffusion. Results for the Radiello aldehyde sampler were inconclusive due to lack of reliable reference methods for all carbonyl compounds of interest.     

Application of sorbent impregnated polyurethane foam (SIP) disk passive air samplers for investigating organochlorine pesticides and polybrominated diphenyl ethers at the global scale

As part of continued efforts under the Global Atmospheric Passive Sampling (GAPS) Network to develop passive air samplers applicable to a wide-range of compounds, sorbent-impregnated polyurethane foam (SIP) disk samplers were codeployed and tested against conventional polyurethane foam (PUF) disk samplers. The SIP disk sampler has a higher sorptive capacity compared to the PUF disk sampler, due to its impregnation with ground XAD resin. The two sampler types were codeployed at 20 sites during the 2009, 3-month long spring sampling period of the GAPS Network. Air concentrations for chlordanes (trans-chlordane, cis-chlordane, and trans-nonachlor) and endosulfans (endosulfan I, endosulfan II, and endosulfan sulfate) derived from PUF disk and SIP disk samplers showed near 1:1 agreement and confirmed previous results for polychlorinated biphenyls (PCBs). Discrepancies observed for α-HCH and γ-HCH in PUF disk versus SIP disk are attributed to lack of "comparability" of the PUF and SIP data sets, due to differences in effective air sampled by the two devices caused by saturation of these higher volatility compounds in the lower capacity PUF disk samplers. Analysis of PBDEs in PUF and SIP disks showed relatively good agreement but highlighted challenges associated with high blanks levels for PBDEs. The higher capacity SIP disk samplers allowed for the analysis of pentachlorobenzene (PeCBz) and hexachlorobenzene (HCBz) and revealed a relatively uniform global distribution of these compounds. The results of this study further validate the SIP disk sampler as a complement to the PUF disk sampler, with capabilities for a broad range of POPs targeted under international POPs treaties such as the Stockholm Convention on POPs and its Global Monitoring Plan.     

PAHs,PCBs, PCNs,organochlorine pesticides,synthetic musks,and polychlorinated n-alkanes in U.K. sewage sludge: survey results and implications

A survey of the digested sludge from 14 U.K. wastewater treatment plants was carried out to obtain contemporary U.K. data on the concentrations of certain classes of persistent organic compounds for which data are scarce and to assess whether U.K. sludge was likely to comply with the sludge limits for PCBs and PAHs proposed by the European Union. Total PAH (24 compounds) concentrations ranged from 67 to 370 mg/kg dw, in line with data from other countries; all the samples would exceed the proposed EU limit. Total PCB concentrations were 110-440 microg/kg dw, well below the proposed EU limit. Total PCN concentrations ranged from 50 to 190 microg/kg. Total synthetic musk concentrations ranged from 2.1 to 86 mg/kg dw; there were a few very high concentrations of HHCB and AHTN in the samples. Total concentrations of the short- and medium-chained polychlorinated alkanes ranged between 7 and 200 mg/kg and between 30 and 9700 mg/kg, respectively. These very high concentrations are indicative of chemicals with numerous and ongoing diffuse sources.     

Further studies on the latitudinal and temporal trends of persistent organic pollutants in Norwegian and U.K. background air

Data are presented for PBDEs, PCBs, and selected organochlorine compounds, measured at background locations by passive air samplers (semipermeable membrane devices, SPMDs) along a latitudinal transect from the south of the U.K. to the north of Norway during 2000-2002. This work is part of an ongoing air sampling campaign in which PCB data were previously obtained in 1994-1996 and 1998-2000. Comparisons of the masses of chemicals sequestered by the SPMDs during these different time intervals are used to investigate spatial and temporal trends. The study yielded examples of compounds that increase, decrease, or remain uniform with latitude, suggestive of differences in the relative importance of deposition versus atmospheric reaction in controlling their long-range atmospheric transport potential. The main constituents of the penta-BDE product were detected at amounts equivalent to 2.0 (range 1.1-2.5) and 1.1 (0.8-1.6) pg m(-3) for the U.K. and Norway background sites, respectively. Fractionation of PBDEs was observed, because the amounts of lighter BDEs decreased with latitude, while the heavier molecular weight congeners were quite uniformly distributed. In contrast, the sequestered amounts of the lighter PCBs were uniformly distributed with latitude, with heavier PCBs decreasing. Sequestered amounts of hexachlorobenzene increased with latitude. Preliminary PCB atmospheric clearance rates were derived using the 1994-1996, 1998-2000, and 2000-2002 data. They averaged ca. 3.5 years for all congeners/locations. No systematic differences in congeners or locations were noted, supporting the hypothesis that the underlying trends in European background air are still controlled by primary, rather than secondary, sources.     

Coupling passive air sampling with emission estimates and chemical fate modeling for persistent organic pollutants (POPs): a feasibility study for Northern Europe

Passive air samplers (polyurethane foam disks) were deployed at 23 background locations along a broadly west-east transect in 8 northern European countries and analyzed for PCBs, PBDEs, PAHs, and a range of organochlorine pesticides (HCB, DDTs, and DDEs). PCBs and PAHs were highest at the center of the transect (Denmark) and lowest in northern Norway. HCB was relatively uniformly distributed, reflecting its persistence and high degree of mixing in air. Higher DDE and DDT levels occurred in Eastern Europe and at several sites in Central Europe. PBDE levels were generally similar at all sites, but lower for some locations in Eastern Europe and Ireland. Emissions information for PCBs, HCB, and PBDEs was used as input for a multi-media chemical fate model, to generate predicted air concentrations and compare with these measured values. Different scenarios were highlighted by this exercise: (i) country and compound combinations where the national inventory gave predicted air concentrations in close agreement with those measured (e.g., PCBs in the UK); (ii) country and compound combinations where predicted concentrations were well below those measured, but where advection of emissions from elsewhere is likely to be important (e.g., PCBs in Norway); (iii) consistent underestimation of compound concentrations by the emissions modeling (i.e., HCB); and (iv) general overestimation of ambient concentrations (i.e., PBDEs). Air mass trajectory analysis showed the likely role of long-range atmospheric transport (LRAT) on national levels. In general, advection from the south and west of Europe appeared to contribute to ambient POPs levels for countries in the center and northeast of the transect. Guidelines are presented as to how countries that want to assess their POPs source inventories can do so with this relatively cheap initial screening approach.     

Single-laboratory validation of a GC/MS method for the determination of 27 polycyclic aromatic hydrocarbons (PAHs) in oils and fats.

A protocol for the measurement of 27 polycyclic aromatic hydrocarbons (PAHs) in vegetable oils by GC/MS has undergone single-laboratory validation. PAHs were measured in three oils (olive pomace, sunflower and coconut oil). Five samples of each oil (one unfortified, and four fortified at concentrations between 2 and 50 microg kg(-1)) were analysed in replicate (four times in separate runs). Two samples (one unfortified and one fortified at 2 microg kg(-1)) of five oils (virgin olive oil, grapeseed oil, toasted sesame oil, olive margarine and palm oil) were also analysed. The validation included an assessment of measurement bias from the results of 120 measurements of a certified reference material (coconut oil BCR CRM458 certified for six PAHs). The method is capable of reliably detecting 26 out of 27 PAHs, at concentration <2 microg kg(-1) which is the European Union maximum limit for benzo[a]pyrene, in vegetable oils, olive pomace oil, sunflower oil and coconut oil. Quantitative results were obtained that are fit for purpose for concentrations from <2 to 50 microg kg(-1) for 24 out of 27 PAHs in olive pomace oil, sunflower oil and coconut oil. The reliable detection of 2 microg kg(-1) of PAHs in five additional oils (virgin olive oil, grapeseed oil, toasted sesame oil, olive margarine and palm oil) has been demonstrated. The method failed to produce fit-for-purpose results for the measurement of dibenzo[a,h]pyrene, anthanthrene and cyclopenta[c,d]pyrene. The reason for the failure was the large variation in results. The likely cause was the lack of availability of (13)C isotope internal standards for these PAHs at the time of the study. The protocol has been shown to be fit-for-purpose and is suitable for formal validation by inter-laboratory collaborative study.     

Proximity of field distribution of polycyclic aromatic hydrocarbons to chemical equilibria among air, water, soil, and sediment and its implications to the coherence criteria of environmental quality objectives

The proximity of PAHs distribution to the equilibrium states among air, soil, water, and bottom sediment was assessed for future risk management and coherence test among environmental quality objectives (EQOs) in these media. Concurrently measured concentration data in the four media were used. In the study areas (Seoul, Shihwa/Banwol, and Taegu), nonequilibrium states prevailed among air, soil, and water except for some light PAHs between air and water. Elevated concentration in soil particularly caused significant deviation from equilibrium between soil and other media. Coherence criteria among these media should be determined based on steady state (not equilibrium) conditions. Sediment was in or near equilibrium with soil for all PAHs, indicating that sediment quality is closely related to soil quality and that the coherence between the EQOs of the two media is required in the study areas. As the concentration ratio of individual PAHs for a given medium pair was found to vary up to 4 orders of magnitude across the study areas, a factor of 10 as a threshold criterion for incoherence is apparently too strict to apply to the national scale of Korea.