聚丙烯改性无卤阻燃复合材料的研究

以聚丙烯(PP)为基材,探讨了不同用量的氢氧化镁(Mg(OH)_2)、微胶囊化红磷(MRP)对PP阻燃性能和力学性能的影响。实验结果表明:随着Mg(OH)_2用量的增加,PP/Mg(OH)_2复合材料的阻燃性能随之升高而力学性能下降。当Mg(OH)_2与MRP复配使用时,MRP的加入可减少Mg(OH)_2的用量,PP/Mg(OH)_2/MRP(100:100:12)与PP/Mg(OH)_2(100:150)的复合材料相比可以看出,拉伸强度、断裂伸长率、冲击强度分别提高了23.73%、38.52%、189%,表明Mg(OH)_2和MRP在PP无卤阻燃复合材料中具有很好的协效阻燃作用。相容剂PP-g-MAH的加入可以提升PP无卤阻燃复合材料的力学性能,PP-g-MAH用量为8份时,PP无卤阻燃复合材料的冲击强度和拉伸强度分别可达4.23kJ/m~2和25.6MPa,同时拥有良好的阻燃性能和加工性能。     

表面改性方法对PP/Mg(OH)2无卤阻燃体系性能的影响

以聚丙烯(PP)为基体树脂,加入采用不同表面改性方法处理的氢氧化镁[Mg(OH)2]制备无卤阻燃PP复合材料。探讨了化学法和辐射法对PP/Mg(OH)2无卤阻燃复合材料阻燃性能和力学性能的影响。结果表明,用烷烃类偶联剂Ao-03进行表面改性的PP/Mg(OH)2具有较好的阻燃性能和力学性能,氧指数可以达到23.8%;拉伸强度变化不大,断裂伸长率达20%,是未处理PP/Mg(OH)2的9.5倍;冲击强度也最高,为未处理PP/Mg(OH)2的7倍。     

PP/Al(OH)_3/Mg(OH)_2/ZB复合材料阻燃性能的研究

测试了PP/Al(OH)3/Mg(OH)2/ZB、PP/Al(OH)3/Mg(OH)2/ZB/CaCO3和PP/Al(OH)3/Mg(OH)2/ZB/CaCO3/POE复合材料的阻燃性能。结果表明:随着阻燃剂用量的增加,氧指数升高,而燃烧速率和烟密度下降,且阻燃剂的加入对延缓燃烧速率的作用效果十分显著;相同配方下试件越厚燃烧速度越慢,且随阻燃剂用量的增加,试件越厚燃烧速率下降的幅度越慢;纳米CaCO3及POE的加入可以增大氧指数,降低烟密度,有利于阻燃,但同时也会使水平燃烧速率略微增大。     

PP/纳米SiO2复合材料的非等温结晶动力学

采用差示扫描量热法研究了聚丙烯（PP）/纳米SiO2复合材料的非等温结晶动力学,研究了纳米粒子的成核活性及复合材料的结晶有效能垒。研究结果表明,纳米SiO2起到异相成核的作用,使PP的结晶峰温升高,结晶总速率增大;增容剂马来酸酐接枝聚丙烯(PP-g-MAH)提高了纳米SiO2的成核活性;添加纳米SiO2使复合材料的结晶有效能垒降低,PP-g-MAH使复合材料的结晶有效能垒增大,但低于纯PP的结晶有效能垒。     

PP-g-MAH对PP/纳米SiO_2复合材料性能的影响

采用熔融共混法制备了聚丙烯(PP)/纳米SiO2复合材料,研究了相容剂马来酸酐接枝聚丙烯(PP-g-MAH)对复合材料力学性能、结晶性能及界面作用的影响。结果表明:PP-g-MAH能有效地增强纳米SiO2与PP基体间的界面作用,提高复合材料的力学性能;同时,PP-g-MAH增强了纳米SiO2的成核活性,使PP的结晶温度升高,球晶细化。     

无卤阻燃聚烯烃弹性体的研究

采用无机阻燃剂Mg（OH）2制备了阻燃聚烯烃弹性体POE,着重考察了Mg（OH）2用量对复合材料力学性能、阻燃性能、耐热性能、结晶性能和加工性能的影响。结果表明：Mg（OH）2用量的增加能够提高复合材料的氧指数,改善其水平燃烧和垂直燃烧效果,但仅在Mg（OH）：质量分数为65％时才能达到最佳的阻燃效果。大量填充未改性Mg（OH）2会导致复合材料力学性能的急剧恶化,适当的表面改性可提高其力学性能。Mg（OH）2能够显著提高复合材料的耐热性能,Mg（OH）2对POE具有异相成核作用。Mg（OH）2用量较大时,复合材料的储能模量和黏度都显著提高。     

β晶型PP/纳米CaCO3/短切PET纤维复合材料的制备

通过熔融挤出共混制备β晶型聚丙烯(PP)/纳米CaCO3/对苯二甲酸乙二酯(PET)纤维复合材料,并用马来酸酐(MAH)接枝PP(PP-g-MAH)改善材料的相容性。研究了PET纤维、β成核剂和相容剂对材料力学性能、相容性和结晶熔融行为的影响。结果表明:CaCO3和PET纤维对PP的结晶具有异相成核作用,能协同诱导形成β晶型PP。加入PET纤维可提高材料的刚性和韧性,但会损坏拉伸性能。PP-g-MAH能改善PP和PET纤维之间的相容性,并能促进成核剂在材料中的分散,形成更多的β晶。     

新型复合成核剂对PP/POE共混物结晶行为的影响

以低分子量聚酰胺6为主体制备了新型复合成核剂,采用高级流变仪、差示扫描量热仪、偏光显微镜等分析手段研究了几种成核剂对聚丙烯/乙烯-1-辛烯共聚物(PP/POE)共混物结晶温度、结晶形态及流变行为的影响。结果表明:新型复合成核剂均可以提高PP/POE共混物的结晶温度、结晶度和结晶速率,减小共混物的球晶尺寸,增加晶核密度,显著提高了PP/POE共混物的结晶性能。     

聚丙烯/蒙脱土纳米复合材料的结晶性能研究

采用差示扫描量热法研究蒙脱土(MMT)对聚丙烯(PP)等温结晶性能的影响。结果表明：加入MMT后提高了PP的结晶速率，使结晶度增大，但对PP熔点的影响不大；加入相容剂PP-g-MAH后，使有机MMT对PP的成核作用更加明显，从而提高了PP／MMT。纳米复合材料的结晶度；PP／MMT纳米复合材料的n值在3左右，其成核方式是异相成核方式。     

废旧丁腈橡胶粉/聚丙烯复合材料的非等温结晶行为

采用熔融共混法制备了废旧丁腈橡胶粉/聚丙烯(WNBR/PP)和废旧丁腈橡胶粉/聚丙烯接枝马来酸酐/聚丙烯(WNBR/PP-g-MAH/PP)复合材料,采用差示扫描量热仪研究了PP、WNBR/PP及WNBR/PP-g-MAH/PP复合材料的非等温结晶过程,并通过Jeziorny方程研究了复合材料的非等温结晶动力学。结果表明,随降温速率的增大,所有试样的结晶峰温和结晶起始温度均向低温偏移,结晶度减小,结晶速率增大。WNBR能起到异相成核的作用,提高了PP的结晶速率,并且导致PP结晶成核和生长机理发生改变。     

Vinyl polysiloxane microencapsulated ammonium polyphosphate and its application in flame retardant polypropylene

Vinyl polysiloxane microencapsulated ammonium polyphosphate (MAPP) was prepared by a sol-gel method using vinyltrimethoxysilane as a precursor to improve its thermal stability and hydrophobicity. The MAPP was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and thermogravimetric analyzer (TGA). The results showed that ammonium polyphosphate (APP) was successfully coated with vinyl polysiloxane. MAPP and pentaerythritol (PER) were used together to improve the flame retardancy of polypropylene (PP). The flame retardant properties of PP composites were investigated by limiting oxygen index (LOI), UL-94 test, TGA and SEM. When the MAPP was added as a flame retardant, with PER as a char forming agent, the LOI of PP/MAPP/PER composites was 33.1%, and it reached the UL-94 V-0 level. The results also demonstrated that the flame retardant properties of PP/MAPP/PER composites were better than those of PP/APP/PER composites at the same loading. Moreover, the addition of flame retardant and carbon forming agent could promote the crystallization behavior of PP.     

Influence of polyamide 6 as a charring agent on the flame retardancy,thermal, and mechanical properties of polypropylene composites

In this work, polyamide 6 (PA6) as a charring agent has been used in combination with thermoplastic polyurethane (TPU)‐microencapsulated ammonium polyphosphate (MTAPP) forming intumescent flame retardants (IFRs) which applies in polypropylene (PP). The effects of the IFRs on the flame retardancy, morphology of char layers, water resistance, thermal properties and mechanical properties of flame‐retardant PP composites are investigated by limiting oxygen index (LOI), UL‐94 test, scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and mechanical properties test. The results show that the PP/MTAPP/PA6 composites exhibit much better flame‐retardant performances than the PP/MTAPP composites. The higher LOI values and UL‐94 V‐2 of the PP/MTAPP composites with suitable amount of PA6 are obtained, which is attributed to the thick and compact char layer structure evidenced by SEM. The results from TGA and DSC demonstrate that the introduction of PA6 into PP/MTAPP composites has a great effect on the thermal stability and crystallization behaviors of the composites. Furthermore, the mechanical properties of PP/MTAPP/PA6 composites are also improved greatly due to the presence of PA6 as a charring agent. POLYM. ENG. SCI., 55:1355–1360, 2015. © 2015 Society of Plastics Engineers     

有机-金属杂化化合物阻燃聚丙烯的研究

将有机-金属杂化三嗪化合物（SCTCFA-ZnO）与聚磷酸铵（APP）复配制备了膨胀型阻燃剂（IFR）,通过极限氧指数测试、垂直燃烧测试、锥形量热分析、热失重分析和扫描电子显微镜分析等表征方法研究了SCTCFA-ZnO/APP的协同作用对PP复合材料阻燃性能的影响。结果表明,APP与SCTCFA-ZnO复配可以有提高PP材料的阻燃性能,当IFR的添加量为25 %（质量分数,下同）,且APP/SCTCFA-ZnO的质量比为2/1时,复合材料的极限氧指数最高,达到31.1 %,达到UL 94 V-0级;IFR可提高复合体系的温热稳定性,阻燃复合材料燃烧后会形成一层致密、连续的炭层,从而起到良好的阻燃效果。     

苯基聚硅氧烷微胶囊化聚磷酸铵的制备及其在PP中阻燃性能研究

采用苯基三甲氧基硅烷为前驱体,通过溶胶凝胶法制备出苯基聚硅氧烷微胶囊化聚磷酸铵（MAPP）。将MAPP作为阻燃剂,季戊四醇（PER）作为成炭剂,制备阻燃聚丙烯（PP）。用傅里叶红外光谱、扫描电子显微镜、能谱仪及热重分析仪对MAPP进行表征。结果表明,聚磷酸铵（APP）被苯基聚硅氧烷成功包覆;较之APP,MAPP的热稳定性和疏水性显著提高;MAPP的阻燃性能优于APP,PP/MAPP/PER复合材料达到V-0级别;阻燃剂及成炭剂的加入对PP的结晶行为有促进作用。     

Study on surface modification and flame retardants properties of ammonium polyphosphate for polypropylene

Microencapsulation ammonium polyphosphate used as flame‐retardant in polypropylene was prepared with hydroxyl silicone oil (HSO) and melamine‐formaldehyde (MF) resin in this article. Fourier transform infrared and energy dispersive spectrometer were used to identify the structure of HSO‐MFAPP. For the HSO‐MFAPP/polypropylene (PP) composites, the flame retardant effect was evaluated by the limiting oxygen index and UL‐94 testing, the compatibility was observed with scanning electron microscope, and the thermal stability was studied by thermogravimetric analysis. The results showed that the microencapsulation of ammonium polyphosphate (APP) with HSO‐MF was prepared by in situ polymerization, and the flame retardant properties and water resistance of the PP/HSO‐MFAPP/pentaerythritol (PER) composites were much better than the ones of the PP/APP/PER composites. Moreover, the compatibility of HSO‐MFAPP with PP was better than that of unmodified APP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Structure and properties of polypropylene composites filled with magnesium hydroxide

Silane and silicone oil modified superfine magnesium hydroxide (MH) was filled into polypropylene (PP) as a flame retardant. The PP and flame‐retarded PP composites were studied for their mechanical properties and rheological behaviors by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), limiting oxygen index (LOI), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The results showed that the addition of MH improved flame retardancy of PP/MH composites, but seriously deteriorated mechanical properties of the composites. Surface treatment of MH could significantly improve tensile and impact strength of PP/MH composite because of its enhanced interfacial adhesion between MH and PP matrix. DSC results showed that MH had heterogeneous nucleation effect on PP. Surface treatment of MH weakened its heterogeneous nucleation effect. POM results showed that the dispersion of MH particles played an important role in the crystalline morphology and spherulite size of PP crystals. TGA indicated that MH greatly enhanced the thermal stability of PP. The introduction of treatment agent further improved the thermal oxidative stability of the composite. According to LOI, silane‐treated MH greatly enhanced flame retardancy of PP/MH composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4943–4951, 2006     

Component ratio effects of hyperbranched triazine compound and ammonium polyphosphate in flame‐retardant polypropylene composites

A hyperbranched derivative of triazine group (EA) was synthesized by elimination reaction between ethylenediamine and cyanuric chloride. The different‐mass‐ratio EA and ammonium polyphosphate (APP) were mixed and blended with polypropylene (PP) in a constant amount (25%) to prepare a series of EA/APP/PP composites. The component ratio effect of EA/APP on the flame‐retardant property of the EA/APP/PP composites was investigated using the limiting oxygen index (LOI), vertical burning (UL‐94), and cone calorimetry tests. Results indicated that the EA/APP/PP (7.50/17.50/75.00) composite with the appropriate EA/APP mass ratio had the highest LOI, UL94 V‐0 rating, lowest heat release rate, and highest residue yield. These results implied that the appropriate EA/APP mass ratio formed a better intumescent flame‐retardant system and adequately exerted their synergistic effects. Furthermore, average effective combustion heat values revealed that EA/APP flame retardant possessed the gaseous‐phase flame‐retardant effect on PP. Residues of the EA/APP/PP composites were also investigated by scanning electron microscopy, Fourier‐transform infrared, and X‐ray photoelectron spectroscopy. Results demonstrated that the appropriate EA/APP mass ratio can fully interact and lock more chemical constituents containing carbon and nitrogen in the residue, thereby resulting in the formation of a dense, compact, and intumescent char layer. This char layer exerted a condensed‐phase flame‐retardant effect on EA/APP/PP composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41006.     

不同粒径成炭剂阻燃聚丙烯体系的性能研究

以自制的三嗪系成炭发泡剂(CFA)为原料,采用球磨机对CFA进行研磨处理,制得不同粒径的CFA。成炭剂与其他阻燃剂复配加入到聚丙烯(PP)中制备阻燃PP材料,通过氧指数和垂直燃烧测定了材料的阻燃性能,同时还研究了材料的力学性能。结果表明:当CFA的粒径为10μm时,阻燃PP材料显示出最好的阻燃性能;随着CFA粒径的减小,材料的力学性能逐渐提高。同时利用扫描电镜测得了炭层的表面形貌,并对阻燃机理进行了研究。     

The flame retardancy and mechanical properties of jute/polypropylene composites enhanced by ammonium polyphosphate/polypropylene powder

Surface flame retarded jute/polypropylene composites (J/P/A) were prepared via a modified strategy: the mixture of PP and APP powder was spread over the surface of jute/PP nonwoven felts, and then transformed into the flame retarded layer by the hot pressing process. The flame retardancy and thermal properties of composites were analyzed by limit oxygen index (LOI), horizontal burning rate (HBR), thermogravimetric analyses (TGA), and differential scanning calorimetry (DSC). We demonstrated that the flame retardancy and mechanical properties of composites was significantly improved compared with those obtained by presoaking the nonwoven fiber felts in flame retardant (FR) solvent before hot pressing. The mechanism of thermal degradation of jute fiber and flame‐retardant mechanism of composites were analyzed by Fourier transform infrared (FTIR), nuclear magnetic resonance (NMR), and scanning electron microscope (SEM). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43889.     

MOS阻燃动态硫化PP/EPDM性能研究

结合碱式硫酸镁晶须（MOS）的补强和阻燃功能，以微胶囊红磷（MRP）为协效剂，制备了无卤阻燃型PP（聚丙烯）／EPDM（三元乙丙橡胶）／MOS／MRP共混物，并与PP／EPDM／Mg（OH）2／MRP共混物进行比较。氧指数（LOI）及垂直燃烧（UL-94）测试表明MOS的阻燃效果优于Mg（OH）2。力学性能测试表明，MOS对PP／EPDM热塑性雌性体具有一定的增强作用，PP／EPDM／MOS／MRP阻燃体系的力学性能明显优于PP／EPDM／／MRP阻燃体系。而PP／EPDM热塑性弹性体的动态硫化进一步提高了PP／EPDM／MOS／MRP阻燃体系的力学与阻燃性能。