A 900-mV low-power ΔΣ A/D converter with 77-dB dynamicrange

The design of a low-voltage and low-power ΔΣ analog-to-digital (A/D) converter is presented. A third-order single-loop ΔΣ modulator topology is implemented with the differential modified switched op-amp technique. The modulator topology has been transformed as to accommodate half-delay integrators. Dedicated low-voltage circuit building blocks, such as a class AB operational transconductance amplifier, a common-mode feedback amplifier, and a comparator are treated, as well as low-voltage design techniques. The influence of very low supply voltage on power consumption is discussed. Measurement results of the 900-mV ΔΣ A/D converter show a 77-dB dynamic range in a 16-kHz bandwidth and a 62-dB peak signal-to-noise ratio for a 40-μW power consumption     

A 1.8-V MOSFET-only ΣΔ modulator using substrate biaseddepletion-mode MOS capacitors in series compensation

A low-voltage high-linearity MOSFET-only ΣΔ modulator for speech band applications is presented. The modulator uses substrate biased MOSFETs in the depletion region as capacitors, linearized by a series compensation technique. A second-order fully differential single-loop architecture has been realized in a conventional 0.25-μm digital n-well CMOS process without extra layers for capacitors. An SNDR of 72 dB and an SNR of 77 dB is obtained with 8-kHz signal bandwidth at an oversampling ratio of 64. The circuit consumes about 1 mW from a single 1.8-V power supply and occupies a core area of 0.08 mm²     

标准数字工艺下16位精度低压低功耗ΣΔ模数调制器设计

针对输入信号频率在20 Hz～24 kHz范围的音频应用,该文采用标准数字工艺设计了一个1.2 V电源电压16位精度的低压低功耗ΣΔ模数调制器。在6 MHz采样频率下,该调制器信噪比为102.2 dB,整个电路功耗为2.46 mW。该调制器采用一种伪两级交互控制的双输入运算放大器构成各级积分器,在低电源电压情况下实现高摆率高增益要求的同时不会产生更多功耗。另外,采用高线性度、全互补MOS耗尽电容作为采样、积分电容使得整个电路可以采用标准数字工艺实现,从而提高电路的工艺兼容性、降低电路成本。与近期报道的低压低功耗ΣΔ模数调制器相比,该设计具有更高的品质因子FOM。     

A 3.3-V CMOS 10.7-MHz sixth-order bandpass ΣΔ modulatorwith 74-dB dynamic range

A 3.3-V bandpass ΣΔ modulator for IF sampling at 10.7 MHz in digital radio applications has been developed. The modulator presents a sixth-order single-loop architecture and features a 74-dB dynamic range in a 2OO-kHz signal bandwidth (FM signal), while for a 9-kHz signal bandwidth (AM signal) the dynamic range is 88 dB. The modulator has been integrated in a standard 0.35-μm CMOS technology using switched-capacitor technique and consumes 76 mW from a single 3.3V supply     

Design and realization of a digital ΔΣ modulator forfractional-n frequency synthesis

The basic operation of a fractional-n frequency synthesizer has been published, but to date little has been presented on the digital ΔΣ modulators which are required to drive such synthesizers. This paper provides a tutorial overview, which relates digital ΔΣ modulation to other applications of ΔΣ modulation where the literature is more complete. The paper then presents a digital ΔΣ modulator architecture which is economical and efficient and which is practical to realize with commercially available components in comparison with other possible implementations which require extensive custom very large-scale integration (VLSI). A demonstration is made of a 28-b modulator using the architecture presented, which provides a 25-MHz tuning bandwidth and <1-Hz frequency resolution. The modulator is demonstrated in an 800-MHz frequency synthesizer having phase noise of -90 dBC/Hz at a 30-kHz offset     

A 1.5-V-100-μW ΔΣ modulator with 12-b dynamic rangeusing the switched-opamp technique

The design and implementation of a very low supply voltage/low power ΔΣ modulator is presented. It is based on the switched-opamp technique, which allows low voltage operation with a standard process and without voltage multiplication. The design methodology is illustrated with a second-order single-loop ΔΣ modulator. The chip is implemented in a 0.7-μm CMOS process with standard threshold voltages. The power supply is 1.5 V and the power dissipation is only 100 μW. The measured dynamic range in the speech bandwidth of 300-3400 Hz is 12 b. The total harmonic distortion (THD) is lower than -72 dB     

A 0.2-mW CMOS ΣΔ modulator for speech coding with 80 dBdynamic range

A CMOS ΣΔ modulator for speech coding with continuous-time loopfilter is presented. Compared to switched-capacitor implementations, the relaxed bandwidth requirements of the active elements of the loopfilter reduce the power consumption. Furthermore, the need for an antialiasing filter at the modulator input is eliminated. A fourth-order, 64× oversampling ΣΔ modulator for application in portable telephones was designed and shows 80 dB dynamic range over the 300-3400 Hz voice bandwidth. Its input is directly connected to the microphone (maximum 40 mV_RMS). Total harmonic distortion (THD) is below -70 dB at 95 μA current consumption from a 2.2 V supply voltage. The active die area of the modulator is 0.5 mm² in a standard 0.5-μm CMOS process     

A switched-capacitor delta-sigma modulator with reduced sensitivityto op-amp gain

Low operational amplifier (op-amp) gain can degrade the performance of a switched-capacitor delta-sigma modulator (ΔΣM). A ΔΣM that incorporates a new gain-compensated switched-capacitor integrator is described. The resulting ΔΣM topology has reduced sensitivity to op-amp gain. Simulation and measurement results for an experimental ΔΣM that demonstrate the advantages of the new architecture are presented     

A 1.8-mW CMOS ΣΔ modulator with integrated mixer forA/D conversion of IF signals

In this paper, the design of a continuous-time baseband sigma-delta (ΣΔ) modulator with an integrated mixer for intermediate-frequency (IF) analog-to-digital conversion is presented. This highly linear IF ΣΔ modulator digitizes a GSM channel at intermediate frequencies up to 50 MHz. The sampling rate is not related to the input IF and is 13.0 MHz in this design. Power consumption is 1.8 mW from a 2.5-V supply. Measured dynamic range is 82 dB, and third-order intermodulation distortion is -84 dB for two -6-dBV IF input tones. Two modulators in quadrature configuration provide 200-kHz GSM bandwidth. Active area of a single IF ΣΔ modulator is 0.2 mm² in 0.35-μm CMOS     

A CMOS 0.8-μm transistor-only 1.63-MHz switched-current bandpassΣΔ modulator for AM signal A/D conversion

This paper presents a CMOS 0.8-μm switched-current (SI) fourth-order bandpass ΣΔ modulator (BP-ΣΔM) IC capable of handling signals up to 1.63 MHz with 105-bit resolution and 60-mW power consumption from a 5-V supply voltage. This modulator Is intended for direct A/D conversion of narrow-band signals within the commercial AM band, from 530 kHz to 1.6 MHz. Its architecture is obtained by applying a low-pass-to-bandpass transformation (z^-1 →-z^-2) to a 1-bit second-order low-pass ΣΔ modulator (LP-ΣΔM). The design of basic building blocks is based upon a detailed analysis of the influence of SI errors on the modulator performance, followed by design optimization. Memory-cell errors have been identified as the dominant ones. In order to attenuate these errors, fully differential regulated-folded cascode memory cells are employed. Measurements show a best SNR peak of 65 dB for signals of 10-kHz bandwidth and an intermediate frequency (IF) of 1.63 MHz. A correct noise-shaping filtering is achieved with a sampling frequency of up to 16 MHz     

CMOS fully-differential bandpass ΣΔ modulator usingswitched-current circuits

The authors present a fourth-order bandpass ΣΔ switched-current modulator IC in 0.8 μm CMOS single-poly technology. It is the first reported integrated circuit realisation of a bandpass ΣΔ modulator using switched-current circuits. Its architecture is obtained by applying a lowpass to bandpass transformation (z¹→-z²) to a second-order lowpass modulator. It has been realised using fully-differential circuitry with common-mode feedback. Measurements show 8 bit dynamic range up to 5 MHz clock frequency     

A 1-V 10-MHz clock-rate 13-bit CMOS ΔΣ modulator usingunity-gain-reset op amps

The problem of low-voltage operation of switched-capacitor circuits is discussed, and several solutions based on using unity-gain-reset of the opamps are proposed. Due to the feedback structure, the opamps do not need to be switched off during the reset phase of the operation, and hence can be clocked at a high rate. A low-voltage ΔΣ modulator, incorporating pseudodifferential unity-gain-reset opamps, is described. A test chip, realized in a 0.35-μm CMOS process and clocked at 10.24 MHz, provided a dynamic range of 80 dB and a signal-to-noise+distortion (SNDR) ratio of 78 dB for a 20-kHz signal bandwidth, and a dynamic range of 74 dB and SNDR of 70 dB for a 50-kHz bandwidth, with a 1-V supply voltage     

Multi-bit cascade ΣΔ modulator for high-speed A/Dconversion with reduced sensitivity to DAC errors

The authors present a ΣΔ modulator (ΣΔM) which combines single-bit and multi-bit quantisation in a cascade architecture to obtain high resolution with a low oversampling ratio. It is less sensitive to the nonlinearity of the digital-to-analogue (DAC) than those previously reported, thus enabling the use of very simple analogue circuitry with neither calibration nor trimming required     

Signal adaptive control architecture for ΔΣ modulatordesign

A signal adaptive control architecture for a second-order ΔΣ modulator design is presented. This architecture effectively reduces the power dissipation and the distortion of the first stage in the modulator. The function of this architecture is to switch off the DAC feedback signal to the first stage during some iterations, and to compensate the signal at the second stage, in an adaptive manner     

Quadrature bandpass ΔΣ modulation for digital radio

A quadrature bandpass ΔΣ modulator IC facilitates monolithic digital-radio-receiver design by allowing straightforward “complex A/D conversion” of an image reject mixer's I and Q, outputs. Quadrature bandpass ΔΣ modulators provide superior performance over pairs of real bandpass ΔΣ modulators in the conversion of complex input signals, using complex filtering embedded in ΔΣ loops to efficiently realize asymmetric noise-shaped spectra. The fourth-order prototype IC, clocked at 10 MHz, converts narrowband 3.75-MHz I and Q inputs and attains a dynamic range of 67 dB in 200-kHz (GSM) bandwidth, increasing to 71 and 77 dB in 100- and 30-kHz bandwidths, respectively. Maximum signal-to-noise plus distortion ratio (SNDR) in 200-kHz bandwidth is 62 dB. Power consumption is 130 mW at 5 V. Die size in a 0.8-μm CMOS process is 2.4×1.8 mm²      

Triangularly weighted zero-crossing detector providingΣΔ frequency-to-digital conversion

It is shown that for delta-sigma (ΣΔ) frequency-to-digital conversion (FDC) there is no need for a ΣΔ modulator, since a limited FM signal itself may be considered as an asynchronous ΣΔ bit-stream. By feeding the limited FM signal directly to a sinc² ΣΔ decimator, a triangularly weighted zero-crossing counter FDC is introduced, providing ΣΔ noise shaping. The results measured confirm the theory     

A two-path bandpass ΣΔ modulator for digital IFextraction at 20 MHz

Oversampled bandpass A/D converters based on sigma-delta (ΣΔ) modulation can be used to robustly digitize the types of narrowband intermediate frequency (IF) signals that arise in radios and cellular systems. This paper proposes a two-path architecture for a fourth-order, bandpass modulator that is more tolerant of analog circuit limitations at high sampling speeds than conventional implementations based on the use of switched-capacitor biquadratic filters. An experimental prototype employing the two-path topology has been integrated in a 0.6-μm, single-poly, triple-metal CMOS technology with capacitors synthesized from a stacked metal structure. Two interleaved paths clocked at 40 MHz digitize a 200-kHz bandwidth signal centered at 20 MHz with 75 dB of dynamic range while suppressing the undesired mirror image signal by 42 dB. At low input signal levels, the mixing of spurious tones at DC and f_s/2 with the input appears to degrade the performance of the modulator; out-of-band sinusoidal dither is shown to be an effective means of avoiding this degradation. The experimental modulator dissipates 72 mW from a 3.3 V supply     

Architecture, design, and test of continuous-time tunableintermediate-frequency bandpass delta-sigma modulators

This paper examines the architecture, design, and test of continuous-time tunable intermediate-frequency (IF) fourth-order bandpass delta-sigma (BP ΔΣ) modulators. Bandpass modulators sampling at high IFs (~100 MHz) allow direct sampling of the RF signal-reducing analog hardware and make it easier to realize completely software programmable receivers. This paper presents circuit design of and test results from continuous-time fourth-order BP ΔΣ modulators fabricated in AlInAs/GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f_T) of 80 GHz and a maximum frequency of oscillation (f_MAX) of about 130 GHz. Operating from ±5-V power supplies, a fabricated 180-MHz IF fourth-order ΔΣ modulator sampling at 4 GS/s demonstrates stable behavior and achieves 75.8 dB of signal-to-(noise+distortion)-ratio (SNDR) over a 1-MHz bandwidth. Narrowband performance (~1 MHz) performance of these modulators is limited by thermal/device noise while broadband performance (~60 MHz), is limited by quantization noise. The high sampling frequency (4 GS/s) in this converter is dictated by broadband (60 MHz) performance requirements     

CMOS oversampling ΔΣ magnetic-to-digital converters

In this paper, two CMOS oversampling delta-sigma (ΔΣ) magnetic-to-digital converters (MDCs) are proposed. The first MDC consists of the magnetic operational amplifier (MOP) and a first-order switched-capacitor (SC) ΔΣ modulator. The second one directly uses the MOP to realize a first-order SC ΔΣ modulator. They can convert the external magnetic field into digital form. Both circuits were fabricated in a 0.5-μm CMOS double-poly double-metal (DPDM) process and operated at a 5-V supply voltage and the nominal sampling rate of 2.5 MHz. The dynamic ranges of these converters are at least ±100 mT. The gain errors within ±100 mT are less than 3% and the minimum detectable magnetic field can reach as small as 1 mT. The resolutions are 100 μT for both of the two MDCs. The measured sensitivities are 1.327 mv/mT and 0.45 mv/mT for the first and the second MDC, respectively     

A 3.2-GHz second-order delta-sigma modulator implemented in InP HBTtechnology

This paper presents a second-order delta-sigma (ΔΣ) modulator fabricated in a 70 GHz (f_T), 90 GHz (f_max) AlInAs-GaInAs heterojunction bipolar transistor (HBT) process on InP substrates. The modulator is a continuous time, fully differential circuit operated from ±5 volt supplies and dissipates 1 W. At a sample rate of 3.2 GHz and a signal bandwidth of 50 MHz (OSR=32100 MSPS Nyquist rate) the modulator demonstrates a Spur Free Dynamic Range (SFDR) of 71 dB (12-b dynamic range). The modulator achieves the ideal signal-to-noise ratio (SNR) of 55 dB for a second-order modulator at an oversampling ratio (OSR) of 32. The design of a digital decimation filter for this modulator is complete and the filter is currently in fabrication in the same technology. This work demonstrates the first ΔΣ modulator in III-V technology with ideal performance and provides the foundation for extending the use of ΔΣ modulator analog-to-digital converters (ADC's) to radio frequencies (RF)