Characterization of indium zinc oxide thin films prepared by pulsed laser deposition using a Zn3In2O6 target

Using a Zn₃In₂O₆ target, indium-zinc oxide films were prepared by pulsed laser deposition. The influence of the substrate deposition temperature and the oxygen pressure on the structure, optical and electrical properties were studied. Crystalline films are obtained for substrate temperatures above 200°C. At the optimum substrate deposition temperature of 500°C and the optimum oxygen pressure of 10⁻³ mbar, both conditions that indeed lead to the highest conductivity, Zn₃In₂O₆ films exhibit a transparency of 85% in the visible region and a conductivity of 1000 S/cm. Depositions carried out in oxygen and reducing gas, 93% Ar/7% H₂, result in large discrepancies between the target stoichiometry and the film composition. The Zn/In (at.%) ratio of 1.5 is only preserved for oxygen pressures of 10⁻²–10⁻³ mbar and a 93% Ar/7% H₂ pressure of 10⁻² mbar. The optical properties are basically not affected by the type of atmosphere used during the film deposition, unlike the conductivity which significantly increases from 80 to 1400 S/cm for a film deposited in 10⁻² mbar of O₂ and in 93% Ar/7% H₂, respectively.     

The optical and electrical properties of copper indium di-selenide thin films

Thin films of copper indium di-selenide (CIS) with a wide range of compositions near stoichiometry have been formed on glass substrates in vacuum by the stacked elemental layer (SEL) deposition technique. The compositional and optical properties of the films have been measured by proton-induced X-ray emission (PIXE) and spectrophotometry (photon wavelength range of 300–2500 nm), respectively. Electrical conductivity (σ), charge-carrier concentration (n), and Hall mobility (μ_H) were measured at temperatures ranging from 143 to 400 K. It was found that more indium-rich films have higher energy gaps than less indium-rich ones while more Cu-rich films have lower energy gaps than less Cu-rich films. The sub-bandgap absorption of photons is minimum in the samples having Cu/In ≈ 1 and it again decreases, as Cu/In ratio becomes less than 0.60. Indium-rich films show n-type conductivities while near-stoichiometric and copper-rich films have p-type conductivities. At 300 K σ, n and μ_H of the films vary from 2.15 × 10⁻³ to 1.60 × 10⁻¹ (Ω cm)⁻¹, 2.28 × 10¹⁵ to 5.74 × 10¹⁷ cm⁻³ and 1.74 to 5.88 cm² (V s)⁻¹, respectively, and are dependent on the composition of the films. All the films were found to be non-degenerate. The ionization energies for acceptors and donors vary between 12 and 24, and 3 and 8 meV, respectively, and they are correlated well with the Cu/In ratios. The crystallites of the films were found to be partially depleted in charge carriers.     

Highly conducting indium tin oxide (ITO) thin films deposited by pulsed laser ablation

Highly conducting and transparent indium tin oxide (ITO) thin films were prepared on SiO₂ glass and silicon substrates by pulsed laser ablation (PLA) from a 90 wt.% In₂O₃-10 wt.% SnO₂ sintered ceramic target. The growths of ITO films under different oxygen pressures (P_O2) ranging from 1×10⁻⁴–5×10⁻² Torr at low substrate temperatures (T_s) between room temperature (RT) and 200°C were investigated. The opto-electrical properties of the films were found to be strongly dependent on the P_O2 during the film deposition. Under a P_O2 of 1×10⁻² Torr, ITO films with low resistivity of 5.35×10⁻⁴ and 1.75×10⁻⁴ Ω cm were obtained at RT (25°C) and 200°C, respectively. The films exhibited high carrier density and reasonably high Hall mobility at the optimal P_O2 region of 1×10⁻² to 1.5×10⁻² Torr. Optical transmittance in excess of 87% in the visible region of the solar spectrum was displayed by the films deposited at Po₂≥1×10⁻² Torr and it was significantly reduced as the P_O2 decreases.     

Transparent conductive In2O3:Mo thin films prepared by reactive direct current magnetron sputtering at room temperature

An amorphous transparent conductive oxide thin film of molybdenum-doped indium oxide (IMO) was prepared by reactive direct current magnetron sputtering at room temperature. The films formed on glass microscope slides show good electrical and optical properties: the low resistivity of 5.9 × 10^− 4 Ω cm, the carrier concentration of 5.2 × 10²⁰ cm^− 3, the carrier mobility of 20.2 cm² V^− 1 s^− 1, and an average visible transmittance of about 90.1%. The investigation reveals that oxygen content influences greatly the carrier concentration and then the photoelectrical properties of the films. Atomic force microscope evaluation shows that the IMO film with uniform particle size and smooth surface in terms of root mean square of 0.8 nm was obtained.     

Temperature dependence of the growth of gallium oxide on CoGa(100)

The oxidation of a CoGa(100) surface at high temperatures has been studied by scanning tunnelling microscopy (STM) and auger electron spectroscopy (AES). When CoGa(100) is oxidised at a sufficiently high temperature (>600 K), an ordered Ga₂O₃ film is formed. The stability of the film depends on the sample temperature and partial oxygen pressure of the ambient gas. At negligible oxygen pressure (<10⁻¹¹ mbar) the oxide is stable up to 850 K. At an oxygen pressure of 10⁻⁶ mbar the oxide is stable up to 930 K and some of the oxide remains present up to 970 K. The oxide film is found to be very uniform. The thickness of the film is constant and independent of the oxidation temperature (600 K<T<930 K), oxygen pressure (<10⁻⁶ mbar), and exposure (10⁻⁴–10⁻² mbar.s≈10²–10⁴ L). We find a clear improvement of the order of the oxide film surface with increasing oxidation temperature. In STM images, a domain structure of the oxide film is observed. The size of the domains increases by a factor of 5–10 when the oxidation temperature is increased from 700 to 900 K.     

New transparent conducting MgIn2O4---Zn2In2O5 thin films prepared by magnetron sputtering

New materials for a transparent conducting oxide film are demonstrated. Highly transparent Zn₂In₂O₅ films with a resistivity of 3.9 × 10⁻⁴ Ω cm were prepared on substrates at room temperature using a pseudobinary compound powder target composed of ZnO (50 mol.%) and In₂O₃ (50 mol.%) by r.f. magnetron sputtering. MgIn₂O₄---Zn₂In₂O₅ films were prepared using MgIn₂O₄ targets with a ZnO content of 0–100 wt.%. The resistivity of the deposited films gradually decreased from 2 × 10⁻³ to 3.9 × 10⁻⁴ Ω cm as the Zn/(Mg + Zn) atomic ratio introduced into the films was increased. The greatest transparency was obtained in a MgIn₂O₄ film. The optical absorption edge of the films decreased as the Zn/(Mg + Zn) atomic ratio was increased, corresponding to the bandgap energy of their materials. It was found that the resistance of the undoped Zn₂In₂O₅ films was more stable than either the undoped MgIn₂O₄, ZnO or In₂O₃ films in oxidizing environments at high temperatures.     

The oxidation kinetics of magnesium at low temperatures and low oxygen partial pressures

The initial oxidation of magnesium at oxygen partial pressures between 1.3 × 10^− 8 Pa and 1.3 × 10^− 5 Pa and at temperatures just above room temperature has been investigated in situ with X-ray photoelectron spectroscopy (XPS) and ellipsometry. Quantitative analysis of the XPS spectra showed that the initially formed oxide has a higher Mg/O ratio (> 1.3) than bulk MgO. Ellipsometry measurements indicated that the band gap values of the oxide layers are considerably smaller than the value expected for bulk MgO ( 2.5 eV vs. 7.8 eV). From the XPS and ellipsometry data recorded as a function of oxidation time the oxidation kinetics have been determined. The kinetics has been described quantitatively with a coupled currents model, involving simultaneous transport of electrons and ions through the oxide layer.     

Indium-doped ZnO thin films deposited by the sol–gel technique

Conducting and transparent indium-doped ZnO thin films were deposited on sodocalcic glass substrates by the sol–gel technique. Zinc acetate and indium chloride were used as precursor materials. The electrical resistivity, structure, morphology and optical transmittance of the films were analyzed as a function of the film thickness and the post-deposition annealing treatments in vacuum, oxygen or argon. The obtained films exhibited a (002) preferential growth in all the cases. Surface morphology studies showed that an increase in the films' thickness causes an increase in the grain size. Films with 0.18 μm thickness, prepared under optimal deposition conditions followed by an annealing treatment in vacuum showed electrical resistivity of 1.3 × 10^− 2 Ωcm and optical transmittance higher than 85%. These results make ZnO:In thin films an attractive material for transparent electrodes in thin film solar cells.     

Characterization of activated reactive evaporated MoO3 thin films for gas sensor applications

Thin films of molybdenum trioxide (MoO₃) were prepared by activated reactive evaporation technique on Pyrex glass substrates. The influence of oxygen partial pressure, substrate temperature and glow power on the structure, surface morphology and optical properties of MoO₃ thin films was studied. The MoO₃ films deposited in an oxygen partial pressure of 1×10⁻³ Torr, glow power of 10 W and substrate temperature of 573 K exhibited predominantly a (0 k 0) orientation corresponding to the orthorhombic layered structure of -MoO₃. The evaluated optical band gap was 3.24 eV. The sensing property of these MoO₃ films for gases like NH₃ and CO was also studied to see the applicability for environmental monitoring. We have observed that the MoO₃ thin films of -phase are capable of detecting NH₃ and CO gases at concentrations lower than 10 ppm in dry air.     

Investigation of optical and electrical properties of ZnO thin films

Zinc oxide (ZnO) thin films were deposited on Si substrates using various working pressures by magnetron sputter. The resistivity of the deposited ZnO films decreases with working pressure, and the resistivity of 4.3 × 10⁻³ Ω cm can be obtained without post annealing. According to the optical transmittance measurements, the optical transmittance above 90% in the wavelength longer than 430 nm and about 80% in the wavelength of 380 nm can be found. Using time-resolved photoluminescence measurement, the carrier lifetime increases with working pressure due to the reduction of nonradiative recombination rate. The reduction of nonradiative recombination rate is originated from the decrease of oxygen vacancies in the ZnO films deposited at a higher working pressure. This result is verified by the photoluminescence measurements. Besides, by increasing the working pressure, the absorption coefficient was decreased and the associated optical energy gap of ZnO thin films was increased.     

Normal metal, ohmic contacts to high-temperature superconducting YBa2Cu3O7-δ thin films suitable for multichip modules

Normal metal, ohmic contacts to high-temperature superconductor (HTSC) materials will be used to form via structures between HTSC interconnect levels, and also, substrate bonding pads in a superconducting multichip module (SMCM). Specific contact resistivities below 10⁻⁸ Ω cm² will be required for such contacts to control signal attenuation and local contact heating of the LN₂cooled SMCM. Previous work on normal metal/superconducting contacts has not focused on metallization schemes which will be stable during subsequent high-temperature processing. Metal contacts of gold, silver, and palladium were formed on superconducting thin films of YBa₂Cu₃O_7-δ via evaporation and sputtering through a shadow mask followed by annealing in various ambients and at several temperatures. Palladium contacts oxidized readily during anneal, and sputtered gold contacts required additional processing and exhibited higher specific contact resistivities. The best contacts were obtained by a controlled-cooling oxygen anneal of evaporated gold or silver, as indicated by normal-state specific contact resistivities of 3 × 10⁻⁵ Ω cm² and 4 × 10⁻⁵ Ω cm², respectively. This work differs from previously published results by describing contacts which required no extensive preparation of the HTSC surface and were stable to 700 °C, indicating these contacts would be compatible with subsequent high-temperature processing of the additional HTSC layers required in a multi-level SMCM.     

Microstructure evolution and texture development during high-temperature uniaxial compression of magnesium alloy AZ31

Texture development in magnesium alloy AZ31 was studied by uniaxial compression tests at temperatures, strain rates and final strains ranging from 573 to 773 K, 1.0 × 10⁻³ to 5.0 × 10⁻⁵ s⁻¹ and −0.2 to −1.5, respectively. Fiber texture was formed in all of the deformation conditions. The main component of the texture varied depending on deformation conditions; it appeared about 33–38° away from the basal pole after the deformation at higher temperatures and lower strain rates. This can be attributed to the increased activity of the secondary pyramidal slip system. With a decrease in temperatures and an increase in strain rate, the tilting angle of the main component (compression plane) from the basal pole decreased down to about 20°. Construction of a basal fiber texture was detected after deformations at the lowest temperature and high strain rates.     

Optically active Er–Yb codoped Y2O3 films produced by pulsed laser deposition

Optically active Er³⁺:Yb³⁺ codoped Y₂O₃ films have been produced on c-cut sapphire substrates by pulsed laser deposition from ceramic Er:Yb:Y₂O₃ targets having different rare-earth concentrations. Stoichiometic films with very high rare-earth concentrations (up to 5.5 × 10²¹ at cm^− 3) have been achieved by using a low oxygen pressure (1 Pa) during deposition whereas higher pressures lead to films having excess of oxygen. The crystalline structure of such stoichiometric films was found to worsen the thicker the films are. Their luminescence at 1.53 μm and up-conversion effects have been studied by pumping the Yb³⁺ at 0.974 μm. The highest lifetime value (up to 4.6 ms) is achieved in films having Er concentrations of ≈ 3.5 × 10²⁰ at cm^− 3 and total rare-earth concentration ≈ 1.8 × 10²¹ at cm^− 3. All the stoichiometric films irrespective of their rare-earth concentration or crystalline quality have shown no significant up-conversion.     

A comparative study of Co thin film deposited on GaAs (1 0 0) and glass substrates

The structural, magnetic and transport properties of Co/GaAs (1 0 0) and Co/glass thin films have been investigated. The structural measurements reveal the crystalline nature of Co thin film grown on GaAs, while microcrystalline nature in case of glass substrate. The film grown on GaAs shows higher coercivity (49.0 G), lower saturation magnetization (3.65 × 10⁻⁴) and resistivity (8 μΩ cm) values as compared to that on glass substrate (22 G, 4.77 × 10⁻⁴ and 18 μΩ cm). The grazing incidence X-ray reflectivity and photoemission spectroscopy results show the interaction between Co and GaAs at the interface, while the Co layer grown on glass remains unaffected. These observed results are discussed and interpreted in terms of different growth morphologies and structures of as grown Co thin film on both substrates.     

Infrared optical properties of Bi2Ti2O7 thin films by spectroscopic ellipsometry

Bi₂Ti₂O₇ thin films have been grown directly on n-type GaAs (1 0 0) by the chemical solution decomposition technique. X-ray diffraction analysis shows that the Bi₂Ti₂O₇ thin films are polycrystalline. The optical properties of the thin films are investigated using infrared spectroscopic ellipsometry (3.0–12.5 μm). By fitting the measured ellipsometric parameter (Ψ and Δ) data with a three-phase model (air/Bi₂Ti₂O₇/GaAs), and Lorentz–Drude dispersion relation, the optical constants and thickness of the thin films have been obtained simultaneously. The refractive index and extinction coefficient increase with increasing wavelength. The fitted plasma frequency ω_p is 1.64×10¹⁴ Hz, and the electron collision frequency γ is 1.05×10¹⁴ Hz, and it states that the electron average scattering time is 0.95×10⁻¹⁴ s. The absorption coefficient variation with respect to increasing wavelength has been obtained.     

Ordered Langmuir-Blodgett films of a substituted lutetium bisphthalocyanine

High-quality LB multilayers have been prepared from the Lu(III) sandwich complex of 2,3,9,10,16,17,23,24-octa (n-butoxy)phthalocyanine (LuPc₂(OBu)₁₆). Surface pressure-area isotherms were characterized and indicate that a stable monolayer is formed corresponding to an area per molecule of 2.4 nm² at 30 mN m⁻¹. The LB films were highly birefringent, and polarized spectra gave dichroic ratios of 3.3 for the 670 nm absorption band and between 0.5 and 2.8 for infrared absorptions. The results indicate that the phthalocyanine rings were highly oriented perpendicular to the dipping direction but somewhat tilted from the substrate normal. The order was shown to be absent when (i) unsubstituted LuPc₂ was used for LB films, or (ii) the horizontal lifting method of film deposition was used, or (iii) the surface pressure was increased to 50 mN m⁻¹, causing a molecular rearrangement. The ordering was improved at 100 °C and finally lost at 280 °C by annealing on a hot stage. The d.c. electrical conductivity of LB films of LuPc₂(OBu)₁₆ was low (σ ≈ 2 × 10⁻⁷ Ω⁻¹ m⁻¹), in contrast with unsubstituted LuPc₂ (σ ≈ 10⁻¹ Ω⁻¹ m⁻¹) and showed no evidence for anisotropy. The findings are in broad agreement with related studies and illustrate some of the many factors involved in improving the structure of phthalocyanine LB films for possible applications.     

Excited-state absorption at 1.57 μm in U:CaF2 and Co:ZnSe saturable absorbers

Appreciable excited-state absorption (ESA) in U²⁺:CaF₂ and Co²⁺:ZnSe saturable absorbers was measured at λ=1.573 μm by optical transmission versus light fluence curves of 30–40 ns long pulses. The ground- and excited-state absorption cross-sections obtained were (9.15±0.3)×10⁻²⁰ and (3.6±0.2)×10⁻²⁰ cm², respectively, for U²⁺:CaF₂, and (57±4)×10⁻²⁰ and (12.5±1)×10⁻²⁰ cm² for Co²⁺:ZnSe. Thus, ESA is not negligible in U²⁺:CaF₂ and Co²⁺:ZnSe, as previously estimated.     

Effects of reduction treatment on the photorefractive properties of Pb0.5Ba0.5Nb2O6

Lead barium niobate is a new photorefractive material of high interest for a variety of applications including holographic storage. Pb_0.5Ba_0.5Nb₂O₆ crystals have been grown by the Bridgman method, and the effects of heat treatments on their photorefractive properties were investigated using Ar ion laser at λ=514.5 nm. The color and absorption spectrum of the crystals varied depending on the oxygen partial pressure during heat treatment. The oxygen diffusivity was estimated to be in the order of 10⁻⁶ and 10⁻⁵ cm²/h at 425 and 550 °C, respectively. Reduction treatment at an oxygen pressure of 215 mTorr increased the effective density of photorefractive charges about three times from 8.0×10¹⁵ to 2.2×10¹⁶ cm⁻³ and made the charge transport more electron-dominant. As a result, the maximum gain coefficient improved from 5.5 to 13.8 cm⁻¹. A diffraction efficiency as high as 70% was achieved in a reduced crystal.     

A parametric study of AlN thin films grown by pulsed laser deposition

High quality AlN thin films were grown at 200–450°C on sapphire substrates by laser ablation of Al targets in nitrogen reactive atmosphere. The nitrogen pressure was varied between 10⁻³ and 10⁻¹ mbar. The reactive gas pressure during irradiation and the temperature of the substrate were found to essentially influence the quality of the layers. X-ray diffraction analysis evidenced the formation of highly orientated layers for a very restrictive set of parameters. Other analysis techniques, like X-ray photoelectron spectroscopy, secondary ion mass spectroscopy, optical transmission spectroscopy have been used to evidence the good stoichiometry and purity of the films. The characteristics of these films were compared with those of AlN thin films deposited in similar experimental conditions, on Si (100) and Si (111) substrates.     

Atomic layer deposition growth of zirconium doped In2O3 films

Zirconium doped indium oxide thin films were deposited by the atomic layer deposition technique at 500 °C using InCl₃, ZrCl₄ and water as precursors. The films were characterised by X-ray diffraction, energy dispersive X-ray analysis and by optical and electrical measurements. The films had polycrystalline In₂O₃ structure. High transparency and resistivity of 3.7×10⁻⁴ Ω cm were obtained.