The preparation of high performance and conductive poly (vinyl alcohol)/graphene nanocomposite via reducing graphite oxide with sodium hydrosulfite

Sodium hydrosulfite is used to reduce graphite oxide in current study. The preparation of poly (vinyl alcohol) (PVA)/graphene nanocomposites is realized using two simple steps: the synthesis of PVA/graphite oxide (GO) nanocomposites film and immersion of such a film in the reducing agent aqueous solution. This method prohibits the agglomeration of GO during direct reduction in PVA/GO aqueous solution, and opens a new way to scale up the production of graphene nanocomposites using a simple reducing agent. A 40% increase in tensile strength and 70% improvement in elongation at break have been obtained with only the addition of 0.7 wt.% of reduced graphite oxide. Furthermore, a good level of conductivity and a variation in the surface property of the prepared films have been observed for the composites containing graphene.     

Graphite oxide/poly(methyl methacrylate) nanocomposites prepared by a novel method utilizing macroazoinitiator

Graphite oxide (GO)/poly(methyl methacrylate) (PMMA) nanocomposites were prepared by a novel method utilizing macroazoinitiator (MAI). The MAI, which has a poly(ethylene oxide) (PEO) segment, was intercalated between the lamellae of GO to induce the inter-gallery polymerization of methyl methacrylate (MMA) and exfoliate the GO. The morphological, conductivity, thermal, mechanical and rheological properties of these nanocomposites were examined and compared with those of intercalated nanocomposites prepared by polymerization with the normal radical initiator, 2,2′-azobisisobutyronitrile. The improvement in conductivity by GO was more evident in exfoliated nanocomposites compared to that of intercalated nanocomposites. For example, a conductivity of 1.78 × 10⁻⁷ S/cm was attained in the exfoliated nanocomposite prepared with 2.5 parts GO per 100 parts MMA, which was about 50-fold higher than that of the intercalated nanocomposite. The thermal, mechanical and rheological properties also indicate that thin GO with a high aspect ratio is finely dispersed and effectively reinforced the PMMA matrix in both exfoliated and intercalated nanocomposites.     

In situ thermal reduction of graphene oxide for high electrical conductivity and low percolation threshold in polyamide 6 nanocomposites

Electrically conductive and thermally stable polyamide 6 (PA 6) nanocomposites were prepared through one-step in situ polymerization of ε-caprolactam monomer in the presence of electrically insulating and thermally unstable graphene oxide (GO) nanosheets. These nanocomposites show a low percolation threshold of ∼0.41 vol.% and high electrical conductivity of ∼0.028 S/m with only ∼1.64 vol.% of GO. Thermogravimetric analysis and X-ray photoelectron spectroscopy results of GO before and after thermal treatment at the polymerization temperature indicate that GO was reduced in situ during the polymerization process. X-ray diffraction patterns and scanning electron microscopy observation confirm the exfoliation of the reduced graphene oxide (RGO) in the PA 6 matrix. The low percolation threshold and high electrical conductivity are attributed to the large aspect ratio, high specific surface area and uniform dispersion of the RGO nanosheets in the matrix. In addition, although GO has a poor thermal stability, its PA 6 nanocomposite is thermally stable with a satisfactory thermal stability similar to those of neat PA 6 and PA 6/graphene nanocomposite. Such a one-step in situ polymerization and thermal reduction method shows significant potential for the mass production of electrically conductive polymer/RGO nanocomposites.     

Preparation of graphene nanosheets/SnO2 composites by pre-reduction followed by in-situ reduction and their electrochemical performances

The Graphene nanosheets/SnO₂ composites were synthesized using stannous chloride to restore the semi-reduction graphene oxide (SRGO) under a simple hydrothermal reduction procedure. First graphene oxide was pre-reduced by glucose for a certain time to get SRGO, which keeps the good water-solubility of graphite oxide (GO) and has a good conductivity like graphene nanosheets. The higher electrostatic attraction between SRGO and Sn²⁺ makes SnO₂ nanoparticles tightly anchor on the graphene sheets in the hydrothermal reduction process. The formation mechanism of the composite was investigated by SEM, TEM, XRD, AFM and Raman. Moreover, the electrochemical behaviors of the Graphene nanosheets/SnO₂ nanocomposites were studied by cyclic voltammogram, electrical impedance spectroscopy (EIS) and chronopotentiometry. Results showed that the Graphene nanosheets/SnO₂ composites have excellent supercapacitor performances: the specific capacitance reached 368 F g⁻¹ at a current density of 5 mA cm⁻², and the energy density was much improved to 184 Wh kg⁻¹ with a power density of 16 kW kg⁻¹, and capacity retention was more than 95% after cycling 500 cycles with a constant current density of 50 mA cm⁻². The experimental results and the thorough analysis described in this work not only provide a potential electrode material for supercapacitors but also give us a new way to solve the reunification of the graphene sheets.     

A facile assembly of polyimide/graphene core–shell structured nanocomposites with both high electrical and thermal conductivities

Polyimide/reduced graphene oxide (PI/r-GO) core–shell structured microspheres were fabricated by in-situ reduction of graphene oxide (GO), which was coated on the surface of PI microspheres via hydrogen bonding and π–π stacking interaction. The highly ordered 3D core–shell structure of PI/r-GO microspheres with graphene shell thickness of 3 nm was well characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM) and Raman spectra. The glass transition temperature (T_g) of PI/r-GO microspheres was slightly increased because of the interaction of r-GO and PI matrix while the temperature at 5% weight loss (T_5%) of PI/r-GO microspheres was decreased due to the side effect of reductant hydrazine hydrate. The PI/r-GO nanocomposites exhibited highly electrical conductivity with percolation threshold of 0.15 vol% and ultimate conductivity of 1.4 × 10⁻² S/m. Besides, the thermal conductivity of PI/r-GO nanocomposites with 2% weight content of r-GO could reach up to 0.26 W/m K.     

Effects of functional groups on the graphene sheet for improving the thermomechanical properties of polyurethane nanocomposites

Dispersibility of graphene sheets in polymer matrices and interfacial interaction are challenging for producing graphene-based high performance polymer nanocomposites. In this study, three kinds nanofillers; pristine graphene nanoplatelets (GNPs), graphene oxide (GO), and functionalized graphene sheet (FGS) were used to prepare polyurethane (PU) composite by in-situ polymerization. To evaluate the efficacy of functional groups on the graphene sheets, PU reinforced with GNPs, GO, and FGS were compared through tensile testing and dynamic mechanical thermal analysis. The Young's moduli of 2 wt% GO and FGS based PU nanocomposites were found significantly higher than that of same amount of GNPs loading as an evidence of the effect of functional groups on graphene sheets for the mechanical reinforcement. The strong interaction of FGS with PU was responsible to exhibit notably high modulus (25.8 MPa) of 2 wt% FGS/PU composite than the same amount of GNPs and GO loading even at elevated temperature (100 °C).     

Crystallization,mechanical performance and hydrolytic degradation of poly(butylene succinate)/graphene oxide nanocomposites obtained via in situ polymerization

Poly(butylene succinate) (PBS)/graphene oxide (GO) nanocomposites were fabricated via in situ polymerization with very low GO content (from 0.03 to 0.5 wt%). The microstructures of the nanocomposites were characterized with Raman spectroscopy, fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), sedimentation experiments and atomic force microscopy (AFM). The results showed that PBS chains have been successfully grafted onto GO sheets during in-situ polymerization, accompanied by the thermo-reduction from GO to graphene. The grafted GO displayed a great nucleating effect on PBS crystallization, resulting in largely improved crystallization temperature and decreased spherules size. A simultaneous enhancement in tensile strength and elongation was achieved for PBS/GO nanocomposites fiber. Meanwhile, increase in hydrolytic degradation rate was also observed for these nanohybrids. Our result indicates that using very low content GO is a simple way to achieve good dispersion yet with remarkable property enhancement for polymer/GO nanocomposites.     

Novel surfactant-stabilized graphene-polyaniline composite nanofiber for supercapacitor applications

In this work, we present a new synthesis method for surfactant stabilized graphene (SSG) combined with polyaniline nanofiber (PANI-Nf) and apply the composite material as supercapacitor (SC) electrodes by screen-printing technique. Surfactant stabilized graphene polyaniline nanofiber composite (PANI-SSG) was synthesized by electrolytic exfoliation of graphite and subsequent interfacial polymerization. Firstly, graphite was electrolytically exfoliated in an electrolyte containing anionic surfactant. Next, ammonium peroxydisulfate initiator and hydrochloric acid were added to the graphene dispersion to form the aqueous phase for interfacial polymerization of polyaniline nanofiber. This dispersion was then added to the water-insoluble solvent phase containing aniline monomer. The polymerization only occurred at the interface of the two immiscible phases leading to polyaniline nanofiber decorated graphene structures. Characterizations by scanning electron microscopy, transmission electron microscopy, atomic force microscopy and Raman spectroscopy suggested nanocomposite formation with intermolecular π-π bonding of graphene with polyaniline nanofibers. Pastes of the materials were screen printed on stainless steel current collectors and tested for SC performance by cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) measurements with 2 M H₂SO₄ electrolyte using a home-built two-electrode test-cell. CV results showed redox peaks of polyaniline with wide cyclic loop, indicating large pseudocapacitance of the nanocomposite. From GCD measurement, a high specific capacitance of 690 Fg⁻¹ at 1 Ag⁻¹ was achieved. Therefore, PANI-SSG nano-composite prepared by electrolytic exfoliation and interfacial polymerization is a promising candidate for SC applications.     

Facile preparation,characterization and performance of noncovalently functionalized graphene/epoxy nanocomposites with poly(sodium 4-styrenesulfonate)

Graphene was noncovalently functionalized with poly(sodium 4-styrenesulfonate) (PSS) and then successfully incorporated into the epoxy resin via in situ polymerization to form functional and structural nanocomposites. The morphology and structure of PSS modified graphene (PSS-g) were characterized with transmission electron microscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The effects of PSS-g additions on tensile, electrical and thermal properties of the epoxy/graphene nanocomposites were studied. Noncovalent functionalization improved interfacial bonding between the epoxy matrix and graphene, leading to enhanced tensile strength and modulus of resultant nanocomposites. The PSS-g additions also enhanced electrical properties of the epoxy/PSS-g nanocomposites, resulting in a lower percolation threshold of 1.2 wt%. Thermogravimetric and differential scanning calorimetric results showed the occurrence of a two-step decomposition process for the epoxy/PSS-g nanocomposites.     

Highly conducting poly(methyl methacrylate)/carbon nanotubes composites: Investigation on their thermal, dynamic-mechanical, electrical and dielectric properties

Nanocomposites of poly(methyl methacrylate) (PMMA) containing various multi-walled carbon nanotubes (MWCNT) contents were prepared using melt mixing. Several techniques were employed to study the influence of the MWCNT addition on the thermal, mechanical, electrical and dielectric properties of the PMMA matrix. The electrical percolation threshold (p_c) was found to be 0.5 vol.% by performing AC and DC conductivity measurements. Significantly high conductivity levels (σ_dc) were achieved: σ_dc exceeds 10⁻² S/cm already at 1.1 vol.%, the criterion for EMI shielding (σ_dc > 10⁻¹ S/cm) is fulfilled at 2.9 vol.%, and the highest loaded sample (5.2 vol.%) gave a maximum value of 0.5 S/cm. Dielectric relaxation spectroscopy measurements in broad frequency (10⁻¹−10⁶ Hz) and temperature ranges (−150 to 170 °C) indicated weak polymer-filler interactions, in consistency with differential scanning calorimetry and dynamic-mechanical analysis findings. Weak polymer-filler interactions and absence of crystallinity facilitate the achievement of high conductivity levels in the nanocomposites.     

Influence of multi-walled carbon nanotubes on electrochemical performance of transparent graphene electrodes

In this work, carbon-carbon nanocomposites as transparent electrodes were prepared by a chemical reduction of graphite oxide (GO) and multi-walled carbon nanotubes (MWNTs). The electric, optical, and electrochemical properties of graphene-MWNT nanocomposites (G-MCs) were investigated as a function of the MWNT content. It was found that chemically bonded G-MCs were successfully formed with a reduction of the functional groups of the GO and acid-treated MWNTs, resulting in the conjugation of 1D MWNTs onto a 2D graphene surface. The electrical conductivity of the graphene was significantly enhanced by introducing the MWNTs. In addition, the G-MCs showed improved current density and high efficiency compared with graphene alone. This indicated that the improved electrochemical performance of the G-MCs can be attributed to the increase in the activity and electrical conductivity enhanced by π-π interaction between graphene and MWNTs.     

Electrical and optical properties of reduced graphene oxide and multi-walled carbon nanotubes based nanocomposites: A comparative study

Graphene and multi-walled carbon nanotubes have attracted interest for a number of potential applications. One of the most actively pursued applications uses graphene and carbon nanotubes as a transparent conducting electrode in solar cells, displays or touch screens. In this work, in situ reduced graphene oxide/Poly (vinyl alcohol) and multi-walled carbon nanotubes/Sodium Dodecyl Sulfate/Poly (vinyl alcohol) composites were prepared by water dispersion and different reduction treatments. Comparative studies were conducted to explore the electrical and optical properties of nanocomposites based on graphene and multi-walled carbon nanotubes. A thermal reduction of graphene oxide was more effective, producing films with sheet resistances as low as 10²–10³ Ω/square with 80% transmittance for 550 nm light. The percolation threshold of the thermally reduced graphene oxide composites (0.35 vol%) was much lower than that of the chemically reduced graphene oxide composites (0.57 vol%), and than that of the carbon nanotubes composites (0.47 vol%). The Seebeck coefficient of graphene oxide films changes from about 40 μV/K to −30 μV/K after an annealing of three hours at 200 °C. The optical absorption of the nanocomposites showed a high absorbance in near UV regions and the photoluminescence enhancement was achieved at 1 wt% graphene loading, while the carbon nanotubes based composite presents a significant emission at 0.7 wt% followed with a photoluminescence quenching at higher fraction of the nanofillers 1.6 wt% TRGO and 1 wt% MWCNTs.     

Thermo-mechanical properties of poly(vinylidene fluoride) modified graphite/poly(methyl methacrylate) nano composites

Poly(methyl methacrylate) (PMMA) nano composites were synthesized by melt compounding technique. Different graphite loadings were investigated, including some treated with poly(vinylidene fluoride) (PVDF). A homogeneous dispersion of graphite throughout the PMMA matrix was observed under microscopic analysis. Thermo-gravimetric analysis showed the incorporation of graphite resulted in improvement of thermal stability of neat PMMA. Dynamic mechanical thermal analysis also showed a significant improvement in the storage modulus over the temperature range of 25–150 °C. Coating the graphite with a small amount of PVDF was found to further extend the improvement in the modulus of the PMMA nano composite at 1 wt.% graphite loading.     

Functionalized graphene sheets filled isotactic polypropylene nanocomposites

The graphene oxide sheets (GOs) reacted with 4,4′-diphenylmethane diisocyanate (MDI) and then stearic acid to form the functionalized graphene sheets (FGs), in order to improve their compatibility with isotactic polypropylene (iPP). The iPP incorporated with FGs were adequately mixed in a Haaker mixer and then compression molded to obtain the iPP/FGs nanocomposites. The crystallization, thermal stability and mechanical properties of the nanocomposites together with iPP/graphite sheets (Gs) and iPP/GOs composites were investigated by differential scanning calorimetry (DSC), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and tensile test. The FGs achieved good dispersion with exfoliated and intercalated nanostructure and strong interfacial adhesion with iPP, which made the nanocomposites have a significant enhancement of thermal stability and mechanical properties at low FGs loadings.     

Graphene sheets anchored with ZnO nanocrystals as electrode materials for electrochemical capacitors

An efficient approach consisted of modified Hummers' method, pulse microwave heating, and homogenizing dispersion has been demonstrated to prepare ZnO/graphene hybrid as electrode material for electrochemical capacitors (ECs). Highly-crystalline ZnO nanoparticles are anchored with graphene sheets, forming three-dimensional framework. The electrochemical properties of ZnO/graphene hybrids are characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge cycling. The EC equipped with ZnO/graphite hybrid (1:5 in w/w) exhibit the improved performance in terms of specific capacitance, high rate capability, and excellent cycling stability, as compared with blank graphene electrode. The maximum energy and power densities of ZnO/graphite capacitor can be obtained as high as 66 Wh kg⁻¹ and 15.2 kW kg⁻¹, respectively. The improved performance can be ascribed to the insertion of ZnO nanocrystals between individual graphite sheets, creating a conducting framework that provides more active sites for the formation of electric double layer. The unique framework allows the electrolyte ions to diffuse easily into the interior channels, leading to small inner resistance.     

Thermoelectric behavior of aerogels based on graphene and multi-walled carbon nanotube nanocomposites

In this work, we presented that the Seebeck coefficient and electrical conductivity can be increased simultaneously in aerogels based on graphene and multi-walled carbon nanotube (graphene-MWCNT) nanocomposites, and at the same time the thermal conductivity is depressed due to 3D porous skeleton structure. As a result, graphene-MWCNT aerogels possess ultra-low thermal conductivities (∼0.056 W m⁻¹ K⁻¹) and apparent density (∼24 kg m⁻³), thereafter the figure of merit (ZT) of ∼0.001 is achieved. Although the ZT value is too low for practical application as a thermoelectric (TE) material, the unique structure in this project provides a potential way to overcome the challenge in bulk semiconductors that increasing electrical conductivity generally leads to decreased Seebeck coefficient and enhanced thermal conductivity.     

Effect of polymer modifier chain length on thermal conductive property of polyamide 6/graphene nanocomposites

The influence of polymer modifier chain length on the thermal conductivity of polyamide 6/graphene (GA) nanocomposites, including through-plane (λ_z) and in-plane (λ_x) directions were investigated. Here, three chain lengths of double amino-terminated polyethylene glycol (NH₂–PEG–NH₂) were used to covalently functionalize graphene with graphene content of 5.0 wt%. Results showed that λ_z was enhanced with the chain length of NH₂–PEG–NH₂ increased, but λ_x reached a maximum value at a certain chain length of NH₂–PEG–NH₂. The maximum λ_z and λ_x of GA are 0.406 W m⁻¹ K⁻¹ and 9.710 W m⁻¹ K⁻¹, respectively. This study serves as a foundation for further research on the thermal conductive property of graphene nanocomposites using different chain lengths of polymer modifier to improve the λ_z and λ_x of the thermal conductive materials.     

Facile preparation and thermal degradation studies of graphite nanoplatelets (GNPs) filled thermoplastic polyurethane (TPU) nanocomposites

A facile method with the advantage of using only one single solvent throughout the whole processing was introduced to prepare graphite nanoplatelet (GNP) filled thermoplastic polyurethane (TPU) nanocomposites. Morphological studies showed that the employed method could provide the uniform dispersion of GNPs in the TPU matrix. Storage modulus of the nanocomposites was increased with increasing GNP content, and the improvement was more obvious at temperatures below the glass transition temperature (T_g) of TPU. For the nanocomposite that contains 3.9 vol% (the maximum loading employed in this study) of GNP, it still showed a long elongation at break of over 600%. Thermogravimetric analysis (TGA) showed that the incorporation of GNPs could improve the thermal stability of the nanocomposites. In addition, cone calorimetry results showed that the GNPs could act as intumescent flame retardant and significantly reduced the heat release rate (HRR), thus improved the flame retardancy of the TPU matrix.     

Highly conductive graphene oxide/polyaniline hybrid polymer nanocomposites with simultaneously improved mechanical properties

Graphene oxide (GO) was added to a polymer composites system consisting of surfactant-wrapped/doped polyaniline (PANI) and divinylbenzene (DVB). The nanocomposites were fabricated by a simple blending, ultrasonic dispersion and curing process. The new composites show higher conductivity (0.02–9.8 S/cm) than the other reported polymer system filled with PANI (10⁻⁹–10⁻¹ S/cm). With only 0.45 wt% loading of GO, at least 29% enhancement in electric conductivity and 29.8% increase in bending modulus of the composites were gained. Besides, thermal stability of the composites was also improved. UV–Vis spectroscopy, X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) revealed that addition of GO improves the dispersion of PANI in the polymer composite, which is the key to realize high conductivity.     

Transparent and flexible ultraviolet photodetectors based on colloidal ZnO quantum dot/graphene nanocomposites formed on poly(ethylene terephthalate) substrates

Transparent colloidal ZnO quantum-dot (QD)/graphene nanocomposites were formed on poly(ethylene terephthalate) (PET) substrates. Ultraviolet (UV)–visible absorption spectra showed a shoulder peak around 350 nm corresponding to the absorption of ZnO QDs. Optical transmittance of the ZnO QD/graphene/PET multilayer was approximately 80%. High-resolution transmission electron microscopy images showed that the ZnO QDs were distributed along the circumferences of the surfaces on the graphene layers. Current–voltage and current–time measurements on the UV photodetector after bending at 300 K exhibited the ON/OFF switching states and stability resulting from the light-induced conductivity of the flexible graphene layer.