2.5Gb/s 0.18μm CMOS时钟数据恢复电路

采用TSMC公司标准的0.18μm CMOS工艺,设计并实现了一个全集成的2.5Gb/s时钟数据恢复电路.时钟恢复由一个锁相环实现.通过使用一个动态的鉴频鉴相器,优化了相位噪声性能.恢复出2.5GHz时钟信号的均方抖动为2.4ps,单边带相位噪声在10kHz频偏处为-111dBc/Hz.恢复出2.5Gb/s数据的均方抖动为3.3ps.芯片的功耗仅为120mW.     

A 40 Gb/s Clock and Data Recovery Module with Improved Phase‐Locked Loop Circuits

A 40 Gb/s clock and data recovery (CDR) module for a fiber‐optic receiver with improved phase‐locked loop (PLL) circuits has been successfully implemented. The PLL of the CDR module employs an improved D‐type flip‐flop frequency acquisition circuit, which helps to stabilize the CDR performance, to obtain faster frequency acquisition, and to reduce the time of recovering the lock state in the event of losing the lock state. The measured RMS jitter of the clock signal recovered from 40 Gb/s pseudo‐random binary sequence (2³¹‐1) data by the improved PLL clock recovery module is 210 fs. The CDR module also integrates a 40 Gb/s D‐FF decision circuit, demonstrating that it can produce clean retimed data using the recovered clock.     

PLL design technique by a loop-trajectory analysis taking decision-circuit phase margin into account for over-10-Gb/s clock and data recovery circuits

A design technique for an over-10-Gb/s clock and data recovery (CDR) IC provides good jitter tolerance and low jitter. To design the CDR using a PLL that includes a decision circuit with a certain phase margin affecting the pull-in performance, we derived a simple expression for the pull-in range of the PLL, which we call the "limited pull-in range," and used it for the pull-in performance evaluation. The method allows us to quickly and easily compare the pull-in performance of a conventional PLL with a full-rate clock and a PLL with a half-rate clock, and we verified that the half-rate PLL is advantageous because of its wider frequency range. For verification of the method, we fabricated a half-rate CDR with a 1:16 DEMUX IC using commercially available Si bipolar technology with f/sub T/=43 GHz. The half-rate clock technique with a linear phase detector, which is adopted to avoid using the binary phase detector often used for half-rate CDR ICs, achieves good jitter characteristics. The CDR IC operates reliably up to over 15 Gb/s and achieves jitter tolerance with wide margins that surpasses the ITU-T specifications. Furthermore, the measured jitter generation is less than 0.4 ps rms, which is much lower than the ITU-T specification. In addition, the CDR IC can extract a precise clock signal under harsh conditions, such as when the bit error rate of input data is around 2/spl times/10/sup -2/ due to a low-power optical input of -24 dBm.     

A 10-Gb/s CMOS CDR and DEMUX IC With a Quarter-Rate Linear Phase Detector

This paper presents a 10-Gb/s clock and data recovery (CDR) and demultiplexer IC in a 0.13-mum CMOS process. The CDR uses a new quarter-rate linear phase detector, a new data recovery circuit, and a four-phase 2.5-GHz LC quadrature voltage-controlled oscillator for both wide phase error pulses and low power consumption. The chip consumes 100 mA from a 1.2-V core supply and 205 mA from a 2.5-V I/O supply including 18 preamplifiers and low voltage differential signal (LVDS) drivers. When 9.95328-Gb/s 2³¹-1 pseudorandom binary sequence is used, the measured bit-error rate is better than 10^-15 and the jitter tolerance is 0.5UIpp, which exceeds the SONET OC-192 standard. The jitter of the recovered clock is 2.1 psrms at a 155.52MHz monitoring clock pin. Multiple bit rates are supported from 9.4 Gb/s to 11.3 Gb/s     

A 2.5-3.125-Gb/s quad transceiver with second-order analog DLL-based CDRs

This paper describes a 2.5-3.125-Gb/s quad transceiver with second-order analog delay-locked loop (DLL)-based clock and data recovery (CDR) circuits. A phase-locked loop (PLL) is shared between receive (RX) and transmit (TX) chains. On each RX channel, an amplifier with user-programmable input equalization precedes the CDR. Retimed data then goes to an 1:8/1:10 deserializer. On the TX side, parallel data is serialized into a high-speed bitstream with an 8:1/10:1 multiplexer. The serial data is introduced off-chip through a high-speed CML buffer having single-tap pre-emphasis. Proposed DLL-based CDR can tolerate large frequency offsets with no jitter tolerance degradation due to its second-order PLL-like nature. Also, this study introduces an improved charge-pump and an improved phase-interpolator. Fabricated in a 0.15-/spl mu/m CMOS process, the 1.9-mm/sup 2/ transceiver front-end operates from a single 1.2-V supply and consumes 65-mW/channel of which 32 mW is due to the CDR. CDR jitter generation and high-frequency jitter tolerance are 5.9 ps-rms and 0.5 UI, respectively, for 3.125 Gb/s, 2/sup 23/-1 PRBS input data with 800-ppm frequency offset.     

Clock and data recovery IC for 40-Gb/s fiber-optic receiver

The integrated clock and data recovery (CDR) circuit is a key element for broad-band optical communication systems at 40 Gb/s. We report a 40-Gb/s CDR fabricated in indium-phosphide heterojunction bipolar transistor (InP HBT) technology using a robust architecture of a phase-locked loop (PLL) with a digital early-late phase detector. The faster InP HBT technology allows the digital phase detector to operate at the full data rate of 40 Gb/s. This, in turn, reduces the circuit complexity (transistor count) and the voltage-controlled oscillator (VCO) requirements. The IC includes an on-chip LC VCO, on-chip clock dividers to drive an external demultiplexer, and low-frequency PLL control loop and on-chip limiting amplifier buffers for the data and clock I/O. To our knowledge, this is the first demonstration of a mixed-signal IC operating at the clock rate of 40 GHz. We also describe the chip architecture and measurement results.     

A Wide-Tracking Range Clock and Data Recovery Circuit

A hybrid analog-digital quarter-rate clock and data recovery circuit (CDR) that achieves a wide-tracking range and excellent frequency and phase tracking resolution is presented in this paper. A split-tuned analog phase-locked loop (PLL) provides eight equally spaced phases needed for quarter-rate data recovery and the digital CDR loop adjusts the phase of the PLL output clocks in a precise manner to facilitate plesiochronous clocking. The CDR employs a second-order digital loop filter and combines delta-sigma modulation with the analog PLL to achieve sub-picosecond phase resolution and better than 2 ppm frequency resolution. A test chip fabricated in a 0.18 mum CMOS process achieves BER <10^-12 and consumes 14 mW power while operating at 2 Gb/s. The tracking range is greater than plusmn5000 ppm and plusmn2500 ppm at 10 kHz and 20 kHz modulation frequencies, respectively, making this CDR suitable for systems employing spread-spectrum clocking.     

Prescaled clock recovery based on small timing misalignment of datapulses

A simple and robust prescaled clock recovery technique is analyzed and demonstrated. An electrical clock is extracted from an ultra-high-speed time-division multiplexed (TDM) RZ signal using a “classic” approach to clock recovery with a detector and a bandpass filter (BPF). A subharmonic tone at the base rate frequency is generated by inducing a small misalignment between adjacent pulses in the transmitted data. The subharmonic tone is recovered as a clock signal at the receiver. Numerical calculations clarify the effect of filter bandwidth, word length, and strength of timing shift on the received timing jitter. Furthermore, it is found numerically that correlated TDM channels will decrease the jitter of the recovered clock considerably. A clock recovery circuit is implemented into an experimental 40 Gb/s and 80 Gb/s optical TDM (O-TDM) system without any observed penalty. Measurements of the timing jitter of the recovered prescaled clock have been performed to verify the numerical results. A 10 GHz clock signal with subpicosecond root-mean-square timing jitter is recovered from a 40-Gb/s O-TDM sequence without a phase-locked loop (PLL) configuration. By using a PLL-configuration, the timing jitter is reduced further by 50%. A discussion on the influence on transmission capacity is performed in general and for nonlinear optical communication systems in particular     

A Jitter-Tolerance-Enhanced CDR Using a GDCO-Based Phase Detector

A jitter-tolerance-enhanced 10 Gb/s clock and data recovery (CDR) circuit is presented. The proposed architecture cascades 2 half-rate CDRs with different loop bandwidth to relax the design bottleneck and the predicted jitter tolerance can be enhanced without sacrificing the jitter transfer. By using a gated digital-controlled oscillator (GDCO), the proposed GDCO-based phase detector may reduce the cost of this architecture and achieve a wide linear range. This CDR circuit has been fabricated in a 0.13 mum CMOS technology and consumes 60 mW from a 1.5 V supply. It occupies an active area of 0.36 mm². The measured rms jitter is 0.96 ps and the peak-to-peak jitter is 7.11 ps for a 10 Gb/s 2⁷-1 PRBS. The measured bit error rate for a 10 Gb/s 2⁷-1PRBS is less than 10^-12.     

A 10-gb/s CMOS clock and data recovery circuit with an analog phase interpolator

This paper presents a 10-Gb/s clock and data recovery (CDR) circuit for use in multichannel applications. The module aligns the phase of a plesiochronous system clock to the incoming data by use of phase interpolation. Thus, coupling between voltage-controlled oscillators (VCOs) in adjacent channels can be avoided. The controller for the phase interpolator is realized with analog circuitry to overcome the speed and phase resolution limitations of digital implementations. Fabricated in a 0.11-/spl mu/m CMOS technology the module has a size of 0.25/spl times/1.4 mm/sup 2/. The power consumption is 220 mW from a supply voltage of 1.5 V. The CDR exceeds the SDH/SONET jitter tolerance specifications with a pseudo random bit sequence of length 2/sup 23/-1 and a bit-error rate threshold of 10/sup -12/. The re-timed and demultiplexed data has an rms jitter of 3.2 ps at a data rate of 2.7 Gb/s.     

A 33-mW 8-Gb/s CMOS clock multiplier and CDR for highly integrated I/Os

A 0.622-8-Gb/s clock and data recovery (CDR) circuit using injection locking for jitter suppression and phase interpolation in high-bandwidth system-on-chip solutions is described. A slave injection locked oscillator (SILO) is locked to a tracking aperture-multiplying DLL (TA-MDLL) via a coarse phase selection multiplexer (MUX). For the fine timing vernier, an interpolator DAC controls the injection strength of the MUX output into the SILO. This 1.2-V 0.13-/spl mu/m CMOS CDR consumes 33 mW at 8Gb/s. Die area including voltage regulator is 0.08 mm/sup 2/. Recovered clock jitter is 49 ps pk-pk at a 200-ppm bit-rate offset.     

A 10-Gb/s CMU/CDR chip-set in SiGe BiCMOS commercial technology with multistandard capability

A 10-Gb/s CMU/CDR chip-set presenting multistandard compliance with SDH/SONET and 10-GbE specifications has been fabricated in a commercial SiGe BiCMOS technology. The clock multiplier unit (CMU) features dual reference clock frequency, and the phase tracking loop uses a charge pump with low common-mode current to minimize frequency ripple; the output jitter is below 80 mUIpp. The clock and data recovery (CDR) features a 20-mV-sensitivity limiting amplifier, a 2-DFF-based decision circuit to maximize clock phase margin (CPM) and a dual-loop phase-locked loop (PLL) architecture with external reference clock. A novel phase detector topology featuring a transition density factor compensation loop has been exploited to minimize jitter. Power consumption is 480 mW and 780 mW, respectively, for the two ICs, from 3.3-V and 2.5-V power supplies     

A 10-Gb/s 16:1 multiplexer and 10-GHz clock synthesizer in0.25-μm SiGe BiCMOS

A 10-Gb/s 16:1 multiplexer, 10-GHz clock generator phase-locked loop (PLL), and 6 × 16 b input data buffer are integrated in a 0.25-μm SiGe BiCMOS technology. The chip multiplexes 16 parallel input data streams each at 622 Mb/s into a 9.953-Gb/s serial output stream. The device also produces a 9.953-GHz output clock from a 622- or 155-MHz reference frequency. The on-board 10-GHz voltage-controlled oscillator (VCO) has a 10% tuning range allowing the chip to accommodate both the SONET/SDH data rate of 9.953 Gb/s and a forward error correction coding rate of 10.664 Gb/s. The 6 × 16 b input data buffer accommodates ±2.4 ns of parallel input data phase drift at 622 Mb/s. A delay-locked loop (DLL) in the input data buffer allows the support of multiple input clocking modes. Using a clock generator PLL bandwidth of 6 MHz, the 9.953-GHz output clock exhibits a generated jitter of less than 0.05 UI_P-P over a 50-kHz to 80-MHz bandwidth and jitter peaking of less than 0.05 dB     

A 2.5-Gb/s clock and data recovery IC with tunable jittercharacteristics for use in LANs and WANs

A 2.5-Gb/s monolithic clock and data recovery (CDR) IC using the phase-locked loop (PLL) technique is fabricated using Si bipolar technology. The output jitter characteristics of the CDR can be controlled by designing the loop-gain design and by using the switched-filter PLL technique. The CDR IC can be used in local-area networks (LANs) and in long-haul backbone networks or wide-area networks (WANs). Its power consumption is only 0.4 W. For LANs, the jitter generation of the CDR when the loop gain is optimized is 1.2 ps (0.003 UI). The jitter characteristics of the CDR optimized for WANs meet all three types of STM-I6 jitter specifications given in ITU-T Recommendation G.958. This is the first report on a CDR that can be used for both LAN's and WAN's. This paper also describes the design method of the jitter characteristics of the CDR for LANs and WANs     

A 10-Gb/s CDR/DEMUX with LC delay line VCO in 0.18-/spl mu/m CMOS

A monolithic 10-Gb/s clock/data recovery and 1:2 demultiplexer are implemented in 0.18-/spl mu/m CMOS. The quadrature LC delay line oscillator has a tuning range of 125 MHz and a 60-MHz/V sensitivity to power supply pulling. The circuit meets SONET OC-192 jitter specifications with a measured jitter of 8 ps p-p when performing error-free recovery of PRBS 2/sup 31/-1 data. Clock and data recovery (CDR) is achieved at 10 Gb/s, demonstrating the feasibility of a half-rate early/late PD (with tri-state) based CDR on 0.18-/spl mu/m CMOS. The 1.9/spl times/1.5 mm/sup 2/ IC (not including output buffers) consumes 285 mW from a 1.8-V supply.     

Loop-parameter optimization of a PLL for a low-jitter 2.5-Gb/sone-chip optical receiver IC with 1: 8 DEMUX

A loop parameter optimization method for a phase-locked loop (PLL) used in wide area networks (WANs) is proposed as a technique for achieving good jitter characteristics. It is shown that the jitter characteristics of the PLL, especially jitter transfer and jitter generation, depend strongly on the key parameter ζω_n (ζ is a damping factor and ω_n is the natural angular frequency of the PLL), and that the optimization focusing on the ω_n dependence of the jitter characteristics make it possible to comprehensively determine loop parameters and loop filter constants for a PLL that will fully comply with ITU-T jitter specifications. Using the optimization method with the low-jitter circuit design technique, a low-jitter and low-power 2.5-Gb/s optical receiver IC integrated with a limiting amplifier, clock and data recovery (CDR), and demultiplexer (DEMUX) is fabricated using 0.5-μm Si bipolar technology (f_T = 40 GHz). The jitter characteristics of the IC meet all three types of jitter specifications given in ITU-T recommendation G.783. In particular, the measured jitter generation is 3.2 ps rms, which is lower than that of an IC integrated with only a CDR in our previous work. In addition, the pull-in range of the PLL is 50 MHz and the power consumption of the IC is only 0.68 W (limiting amplifier: 0.2 W, CDR (PLL): 0.3 W, DEMUX: 0.18 W) at a supply voltage of -3.3 V and only 0.35 W at a supply voltage of -2.5 V (without output buffers)     

2.5-Gb/s low-jitter low-power monolithically integrated optical receiver

A high-scale integrated optical receiver including a preamplifier, a limiting amplifier, a clock and data recovery (CDR) block, and a 1:4 demultiplexer (DEMUX) has been realized in a 0.25???m CMOS technology. Using the loop parameter optimization method and the low-jitter circuit design technique, the rms and peak-to-peak jitter of the recovered 625-MHz clock are 9.4 and 46.3?ps, respectively, which meet the jitter specifications stipulated in ITU-T recommendation G.958. The recovered and frequency divided 625?MHz clock has a phase noise of ?83.8 dBc/Hz at 20?kHz offset in response to 2.5?Gb/s PRBS input data (2²³?C1), and the 2.5?Gb/s PRBS data has been demultiplexed into four 625?Mb/s data. The power dissipation is only 0.3?W under a single 3.3 V supply (excluding output buffers).     

1.25～3.125 Gb/s连续数据速率CDR设计

设计了一款工作速率为1.25～3.125 Gb/s的连续可调时钟数据恢复(CDR)电路,可以满足多种通信标准的设计需求.CDR采用相位插值型双环路结构,使系统可以根据应用需求对抖动抑制和相位跟踪能力独立进行优化.针对低功耗和低噪声的需求,提出一种新型半速率采样判决电路,利用电流共享和节点电容充放电技术,数据速率为3.125 Gb/s时,仅需要消耗50 μA电流.芯片采用0.13 μm工艺流片验证,面积0.42 m㎡,功耗98 mw,测试结果表明,时钟数据恢复电路接收PRBS7序列时,误码率小于10-12.     

10 GHz full-rate clock and data recovery circuit in 0.18 /spl mu/m CMOS without external reference clock

The design of a fully monolithic integrated 10 GHz full-rate clock and data recovery (CDR) circuit in 0.18 /spl mu/m digital CMOS technology, which employs an injection phase-locked loop (PLL) technique is presented. The CDR operating without the external reference exhibits a capture range of 200 MHz while consuming 205 mA current from 1.8 V supply including the output buffer. The recovered clock signal with 250 mV/sub pp/ pseudorandom bit Sequence input data of length 2/sup 31/-1 exhibits 7.9 ps of peak-to-peak (p-p) and 1.1 ps of root-mean-square (RMS) jitter. The measured clock phase noise at 1 MHz offset is approximately -109 dBc/Hz.     

一种适用于内嵌时钟串行链路的5Gbps小面积CDR

本文提出了一种支持多标准的具有系数可调的均衡器和宽跟踪能力的时钟数据恢复电路。基于对系统参数和一阶 bang-bang 时钟数据恢复电路的环路特性分析,推导出电路设计参数。考虑到抖动性能,追踪能力以及芯片面积,文中采用了一阶数字滤波器和6-bit DAC以及高线性度的相位插值器实现了高相位调整精度和小面积的时钟恢复电路,同时该结构实现了±2200ppm的频偏跟踪能力,使得该结构适用于不同源的高速串行传输系统,尤其是内嵌时钟结构。该设计已经在55nm CMOS工艺上流片验证,测试结果显示符合误码率的要求以及抖动容忍规范。该测试芯片整体面积是0.19mm2,其中时钟恢复电路只占0.0486mm2 而且该电路工作在5Gbps,供电电压为1.2V时,只消耗30mW。