PBT/PA6/CYD-011共混体系的力学性能及形态结构的研究

通过熔融共混制备了环氧树脂CYD-011增容的PA6/PBT共混物。实验结果表明:环氧树脂可以明显改善PBT/PA6共混体系相容性,降低了分散相粒子尺寸,提高了界面强度,力学性能得到显著提高。通过对试样进行热处理,探讨了不同热处理温度对PA6/PBT共混体系力学性能的影响,表明经长时间高温处理,通过环氧树脂增容,共混物力学性能仍得到了明显提高。     

剪切作用下POE-g-MAH和PP-g-MAH对PA1010/PP共混物的增容作用

采用熔融共混的方法制备了聚酰胺1010/聚丙烯（PA1010/PP）共混物,通过扫描电镜、力学性能和差示扫描量热等方法研究了剪切作用下马来酸酐接枝乙烯-辛烯共聚物（POE-g-MAH）和马来酸酐接枝聚丙烯（PP-g-MAH）对PA1010/PP共混物的增容作用。结果表明,同样条件下,PP-g-MAH增容体系的相区尺寸较小,相界面更模糊,PP相的结晶温度和结晶度明显提高,共混物的拉伸强度和冲击强度均高于非增容体系。而POE-g-MAH增容体系的相区尺寸相对较大,PP相的结晶温度和结晶度明显降低,共混物只有冲击强度明显高于非增容体系,拉伸强度略低于非增容体系。     

PP-g-MAH对PA6/PP共混体系性能的影响

以PP-g-MAH为相容剂,研究了PP-g-MAH对PA6/PP共混体系性能的影响。探讨了PP-g-MAH对PA6/PP共混物增容作用,提高共混物的各项性能指标。当PP-g-MAH为4份时,共混物的力学性能最好,当PA6/PP=90/10时,其力学性能有最大值;SEM照片显示,未加PP-g-MAH时,PP在PA6基体上分散不均,颗粒大,当加入适量的PP-g-MAH(4份)时,PP分散比较均匀,颗粒尺寸明显降低。以PP-g-MAH4份,PA6/PP=80/20制备的共混物,吸水率约是PA6的15%:冲击强度、热变形温度分别比PA6、PP提高了72%和106%,13.5℃和5.5℃。     

增容剂对PP/PA66共混物力学性能和结晶行为的影响

采用熔融共混法制备了聚丙烯(PP)/聚酰胺66(PA66)共混物,研究了聚丙烯接枝马来酸酐(PP-g-MAH)和乙烯-辛烯共聚物接枝马来酸酐(POE-g-MAH)作为增容剂对PP/PA66共混物力学性能和非等温结晶行为的影响。结果表明:PP-g-MAH提高了共混体系的拉伸强度,加入5份POE-g-MAH能显著提高共混物的断裂伸长率;PA66可起到异相成核作用,使PP的结晶峰温度升高;加入PP-g-MAH进一步提高了PP的结晶峰温度;PA66使PP的结晶活化能增大,增容剂的加入则使共混体系中PP的结晶活化能降低。     

接枝聚丙烯增容改性PP/PA合金性能的研究

用PP接枝物增容PP/PA6共混体系,观察分析了共混合金的形态结构特点,测试了共混物的力学性能.结果表明：单独加入PP-g-MAH,力学性能均呈现先升后降的趋势,峰值时拉伸强度比未加接枝物时可提高20%,弯曲强度比未加接枝物时提高了54%,冲击强度比不添加接枝物时提高了3.6%.添加PP-g-MAH对不同比例PP/PA6共混物力学性能的影响不同,固定PP-g-MAH用量为4%,PA6质量分数为30%时共混物的综合力学性能达到最好.用PP-g-MAH和PP-g-GMA两种接枝物共同作为相容剂加入到PP/PA6共混物中比单独使用一种的效果要好,拉伸、弯曲和冲击强度都得到显著的提高.由共混物的SEM照片可以看到,PP-g-MAH使分散相的粒径变小,分布均匀,界面相互作用加强,所以是PP/PA6共混物的有效增容剂.     

PC/PBT改性聚丙烯的研究

以聚碳酸酯(PC)和聚对苯二甲酸丁二醇酯(PBT)并用且以马来酸酐接枝聚丙烯(PP-g-MAH)作为相容剂来改性聚丙烯(PP),详细研究了PC/PBT改性PP的工艺条件以及不同结构对PP共混物性能的影响。结果表明,当PC与PBT的质量分数分别为5.0%和2.5%时,改性PP共混物的拉伸强度为24.0 MPa,缺口冲击强度达到28.9kJ/m~2,比未改性PP的冲击强度提高了7倍。同时研究了PP-g-MAH的用量对PP共混物性能影响,当PC与PBT的质量分数分别为10.0%和5.0%时,PP-g-MAH的质量分数为2.0%时,共混物的缺口冲击强度达到27.8kJ/m~2。PP-g-MAH可有效提高PC/PBT与PP之间的相容性。     

增容剂对PP/r-PET共混体系结构与性能影响

采用熔融接枝法制备了聚丙烯(PP)接枝甲基丙烯酸缩水甘油酯接枝物(PP-g-GMA)和聚丙烯接枝马来酸酐接枝物(PP-g-MAH),并用PP-g-GMA和PP-g-MAH作为PP/回收聚对苯二甲酸乙二醇酯(PP/r-PET)共混体系(质量份之比100/12)的增容剂。通过对共混体系进行分析,研究了PP-g-GMA和PP-g-MAH对PP/r-PET共混体系结构与性能的影响。结果表明:成功制备了PP-g-GMA和PP-g-MAH;PP-g-GMA的MFR(熔体流动速度)低于PP-g-MAH的;PP-g-GMA质量份为6份时,共混体系的拉伸强度和冲击强度较未增容体系提高了54.8%和21.8%,增强与增韧效果较明显;当PP-g-MAH质量份为6份时,共混体系的拉伸强度提高了52.1%,但冲击强度稍有降低;PP-g-GMA使得r-PET在PP中分布更均匀。     

PA6/SMA/N-PMI共混物的制备及其性能研究

采用熔融共混法制备了尼龙6/苯乙烯-马来酸酐共聚物/N-苯基马来酰亚胺共混物(PA6/SMA/N-PMI),并利用DSC、TGA及力学性能测试等手段研究了SMA用量对PA6/SMA/N-PMI共混物熔融结晶行为、热学性能以及力学性能的影响。结果表明,共混物的最大分解温度较纯PA6有较大提高;SMA用量的增加,共混物的结晶温度、结晶度以及熔融焓均先降低再升高;当SMA用量为5份时,共混物的弯曲强度、弯曲模量以及热变形温度均达到最大值,分别为113.8、3 053 MPa及61.3℃,较纯PA6分别提高了25.1%、28.0%及19.0%;拉伸强度在SMA用量为7.5份时达到最大值81.4 MPa,较纯PA6提高了17.1%。     

玻璃纤维增强PA 6/PBT低吸湿共混物的力学性能

以马来酸酐接枝乙烯-辛烯共聚物(POE-g-MAH)和乙烯-甲基丙烯酸丁酯-丙烯酸缩水甘油酯三元共聚物(PTW)为复合相容剂,在平行同向双螺杆挤出机上熔融共混,制备了玻璃纤维增强聚酰胺(PA)6/聚对苯二甲酸丁二酯(PBT)共混物。考察了复合相容剂对增强共混材料力学性能的影响,并探讨了共混物的吸湿性与力学性能的关系。结果表明:相容剂的复合使用有协同作用;PA 6/PBT共混体系随w(PBT)增加,力学性能下降,w(PBT)增加到32.0%时,拉伸强度、弯曲强度、简支梁缺口冲击强度分别下降25.2%,15.8%,45.3%;并且随w(PBT)增加,共混体系对吸湿的敏感性降低。     

PTT/PP共混物的性能研究

通过熔融共混制备了聚对苯二甲酸丙二酯/聚丙烯(PTT/PP=75/25)及其马来酸酐接枝PP(PP-g-MAH)增容共混物,研究了PTT/PP及其增容共混物的结晶性能、力学性能、流变性能和结晶形态。研究结果表明,PTT与PP共混能提高PP、PTT组分的结晶温度;对于增容共混物,随PP-g-MAH用量的增加,PP和PTT的结晶温度基本不变。加入PP使PTT拉伸强度降低,冲击强度提高;PP-g-MAH增容使共混物的拉伸和冲击强度都提高。增容共混物的熔体粘度明显降低,存在明显的剪切变稀现象,但熔体粘度与PP-g-MAH用量无关。在一定用量范围内,随PP-g-MAH用量的增加,PP分散相的尺寸变小。     

Preparation and properties of poly(Nε,Nε-dicarboxymethyl-l-lysine)

A new ampholytic homopolypeptide, $\text{poly}\text{(N}{}^{\mathrm{\epsilon }}\text{,N}{}^{\mathrm{\epsilon }}\text{-}\text{dicarboxy-methyl-}\text{l}\text{-lysine}\text{)}$, which has one tertiary amino and two carboxyl groups in the side chain has been derived from a hydrochloride salt of poly(L-lysine). The polymer in aqueous solution seems to be in the coil form with locally extended structure (LES) at neutral pH. In both the acidic and alkaline regions, the molar ellipticity of the polymer changes as a result of change in net charge on the side chain. The conformational changes may be from the coil with LES to other coiled forms. 5–7 M NaClO₄ and 80% aqueous methanol induce the α-helix in the polymer at neutral pH. Divalent cations, Cu²⁺ and Ca²⁺, do not induce any remarkably ordered structures such as α-helix or β-structure in the polymer in aqueous solution at any pH. Ultraviolet absorption studies show an absorption peak of the polymer-Cu²⁺ complex near 240 nm. Dependence of the peak intensity on pH at various q values ($\text{q =}\text{[}\text{Cu}{}^{\mathrm{2+}}\text{]}\text{[}\text{residue}\text{]}$) indicates the two steps of the complex formation. At q less than 0.64, the formation is described only with the first step. An average coordination number for Cu²⁺ at the first step was calculated to be about 2 by the method of Mandel and Leyte. The association constant of Cu²⁺ with the residue at the step was determined from the absorption data to be far smaller than that for the Cu²⁺-EDTA complex. The second step of the formation occurs in the case of large q but the absorption data for the second step cannot be obtained exactly due to precipitation.     

Wet Milling of Fe/Al/Al2O3 and Fe2O3/Al/Al2O3 Powder Mixtures

Wet milling of Al₂O₃-aluminide alloy (3A) precursor powders in acetone has been investigated by milling Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixtures. The influence of the milling process on the physical and chemical properties of the milled powders has been studied. Particle refinement and homogenization were found not to play a dominant role, whereas plastic deformation of the metal particles leads to the formation of dislocations and a highly disarranged polycrystalline structure. Although no chemical reactions among the powder components in Fe₂O₃/Al/Al₂O₃ powder mixtures were observed, the formation of a nanocrystalline, ordered intermetallic FeAl phase in Fe/Al/Al₂O₃ powder mixtures caused by mechanical alloying was detected. Chemical reactions of Fe and Al particle surfaces with the atmosphere and the milling media lead to the formation of highly porous hydroxides on the particle surfaces. Hence the specific surface area of the powders increases, while the powder density decreases during milling. The fraction of Fe oxidized during milling was determined to be 0.13. The fraction of Al oxidized during milling strongly depends on the metal content of the powder mixture. It ranges between 0.4 and 0.8.     

Sintering of Si3N4-Y2O3-Al2O3

Sintering kinetics of the system Si₃N4-Y2O₃-Al₂O3 were determined from measurements of the linear shrinkage of pressed disks sintered isothermally at 1500° to 1700°C. Amorphous and crystalline Si₃N₄ were studied with additions of 4 to 17 wt% Y₂O₃ and 4 wt% A1₂O₃. Sintering occurs by a liquid-phase mechanism in which the kinetics exhibit the three stages predicted by Kingery's model. However, the rates during the second stage of the process are higher for all compositions than predicted by the model. X-ray data show the presence of several transient phases which, with sufficient heating, disappear leaving mixtures of β ' -Si₃N₄ and glass or β '-Si₃N₄, α '-Si₃N₄, and glass. The compositions and amounts of the residual glassy phases are estimated.     

Participation of lewis base on vinyl chloride polymerization with Al(C2H5)3CCl4 catalyst system

The polymerization of vinyl chloride has been investigated using an $\text{Al}\text{(}\text{C}{}_2\text{H}{}_5\text{)}{}_3\text{CCl}{}_4$ catalyst system in the presence of various Lewis bases. Effective Lewis bases are γ-butyrolactone, diglyme and diethylenetriamine which are multidentate. The rate of polymerization is dependent not only on the basicity of the Lewis base used but also on a coordination number of one. The latter is the predominant factor. For the effect of polymeric amines, a tentative hypothesis is discussed.     

Synthesis and Characterization of Ti0.33Ta0.33Nb0.33C and Ti0.33Ta0.33Nb0.33CxN1-x Whiskers

Ta_0.33Ti_0.33Nb_0.33C and Ta_0.33Ti_0.33Nb_0.33C _x N_{1− x} whiskers were synthesized via a carbothermal vapor-liquid-solid growth mechanism in the temperature range 900°-1450°C in Ar or N₂. The optimum temperature was 1250°C. Whiskers were obtained in a yield of 70-90 vol%. The whiskers were 0.5–1 µm in diameter and 10–30 µm in length. The starting materials that produced the highest whisker yield were: TiO₂, Ta₂O₅, Nb₂O₅, C, Ni, and NaCl. C was added to reduce the oxides, and Ni to catalyze whisker growth. NaCl was used as a source of Cl for vapor-phase transportation of Ta and Nb oxochlorides and Ti chlorides to the catalyst. The catalyst metal was recycled several times during the synthesis and was transported as NiCl₂( g ) according to thermodynamic calculations. The rate of formation and the chemical composition of the whiskers depended on the synthesis temperature, the choice of catalyst, and the atmosphere. At low temperatures, the whiskers were enriched in Nb and Ta, whereas the Ti content increased with increased synthesis temperature.