共查询到19条相似文献,搜索用时 93 毫秒
1.
金属挤压用圆(扁)挤压筒优化设计与制造实践 总被引:1,自引:0,他引:1
针对挤压筒结构设计、有限元强度计算、原材料选择、热处理及多层挤压筒过盈量的选定等影响挤压筒寿命的诸多问题,结合近三十年挤压筒设计制造实践进行了详尽的论述。 相似文献
2.
3.
4.
3 在金属挤压成形过程的数值模拟与物理模拟方面取得的主要成果3.1 铝合金挤压时温升有限元分析利用工程计算法可计算出热能的发生源和发生量,用微分方程式和有限元法可计算出发生热的热传导。基于上述原理建立了数学模型,选择和处理边界条件、单元及其划分,围绕坯料、挤压筒、模具等,计算和确定了坯料温升的热源、坯料内的热传导、挤压筒壁周围发热产生的温升和模孔周围发热引起的温升、向模具和挤压筒扩散的热、挤压温升与挤压速度的关系问题,为合理设计挤压工艺和挤压工模具提供了依据。3.2 挤压模内温度场的有限元分析在铝型材热挤压… 相似文献
5.
扁挤压筒型腔有限元应力分析及形线优化 总被引:2,自引:0,他引:2
本文对850x320mm扁挤压筒内套进行了有限元分析计算,运用优化设计理论对扁挤压筒型腔进行计算机辅助形状优化设计,确定了使应力集中系数降为最小的最优形线,为延长扁挤压筒使用寿命提供了一条有效途径。 相似文献
6.
7.
本着研究自制使挤压筒立足省内 ,降低成本为目的。通过研究、探索、实践 ,经生产使用证明 ,基本接近国外制造、组装的技术水平。本文就挤压筒的选材、设计计算、组装、脱套更换等关键技术问题都作了具体的阐述 相似文献
8.
9.
目前,用于计算反向挤压力的公式,都是根据相应的正向挤压力计算公式,直接令金属与挤压筒内壁间的摩擦为零得来的,其它参数的确定基本上与正向挤压时相同。在实践中发现,按照这些公式计算出的挤压力往往与其实测值有较大差异。本文结合对比实验,分析了造成这种差异的主要原因:只注意了反向挤压时挤压筒内壁上无摩擦,而忽略了反向挤压时金属的变形流动规律与正向挤压时不同;塑性变形区和死区的形状、位置与正向挤压不同,其体积远比正向挤压时小;变形区中的温升比正向挤压时小得多;加工硬化程度比正向挤压时大;制订工艺时锭坯的加热温度比正向挤压时低,挤压速度比正向挤压时快,等等。计算反向挤压的挤压力时,如果直接采用这些公式,应选用不同于正向挤压时的变形抗力值。 相似文献
10.
11.
12.
13.
B. I. Kamenetskii Yu. N. Loginov N. A. Kruglikov 《Russian Journal of Non-Ferrous Metals》2017,58(2):124-129
A new cold deformation method of cast magnesium is proposed. The method includes the implementation of the upsetting technique under lateral pressure. The billet is initially placed into a jacket made of ductile metal and then into a container. The billet is affected with a puncheon placed into the container with a gap. Under the press force, the jacket metal flows into the gap and forms the pressure. This results in an increase in the level of compressing stresses, which increases the ductility of magnesium. Deformation tests of cast magnesium samples showed that the relative reduction without destruction can be increased from 12?18 to 60–70%. Such an increase in ductility makes it possible to produce deformed magnesium billets without heating. A simplified removal procedure of the samples from jackets after the completion of deformation is foreseen. It is revealed that the process can be performed at average upsetting pressures of 820–830 MPa, which is acceptable for modern tool materials. 相似文献
14.
In this paper, the Navier-Stokes equation of fluid, which is incompressible, viscous, changeful, and free surface, is solved by the method of volume of fluid to obtain the dynamic liquid pressure in a rectangular container. The simplified simulating calculation formulas are given in order to apply the method in engineering on the basis of calculation results and analysis. 相似文献
15.
16.
根据普通碳素钢的反弯矫直计算方法,对高速钢棒材的反弯矫直压下量进行了修正,并通过矫直实验进行了验证。 相似文献
17.
结合生产实际,分析了现行中小型卧式挤压机用挤压轴结构设计上的不足,通过校核计算验证了挤压轴失效形式的原因,提出了建议及措施。 相似文献
18.
S. V. Samusev A. V. Lyuskin A. I. Romantsov K. L. Zhigunov A. N. Fortunatov 《Steel in Translation》2014,44(3):196-198
A method is developed for determining the ratio of the contact and noncontact zones in the deformation region on a stepwise-shaping press. Two histograms express the calculation results for biradial and triradial billet profiles in the deformation region with permissible reduction. 相似文献
19.
分析了现行大型卧式挤压机用中250挤压针设计缺陷,提出了分段选材、分段设计以及适当增大挤压针根部螺纹断面的有效面积等优化方案,通过模拟校核计算和实际改进,获得了挤压针关键部位硬度、强度更为经济合理的搭配设计方案。 相似文献