A quantitative evalution of the photocatalytic performance of TiO2 slurries

This paper reports the results of a comparison between two TiO₂ photocatalysts that differ for particle size and absorption/scattering optical properties. The catalyst with larger particles and lower surface area performed better in the degradation of phenol than the specimen with smaller particles and larger surface area. Following carefully designed experiments, it is possible to assess the relative role of light absorption/scattering properties and catalyst-related efficiency by means of a basic kinetic model for the rate of photocatalytic reactions. Explicit relationships are derived in the framework of the steady-state approximation for the quantum yield as a function of one a-dimensional number collecting surface kinetic constants for charge carrier reactions at the interface, absorbed light and surface substrate concentrations. The dimensionality change to volume-defined quantities allows derivation of the explicit dependence of the quantum yield on substrate concentration and partition constants, catalyst concentration, and the rate of volumetric light absorption. Following this approach, the rate expression for slurry systems, valid in the absence of back reactions, is directly derived. Some further simplification of the rate equation for the case of low quantum yield regime leads to analytical relationships able to account for the dependence of the rate on catalyst concentration and absorbed light in the case of stirred and unstirred conditions. The reported properly designed experiments allow the estimation of catalyst-specific micro-kinetic constants.     

Photocatalytic activity of Cu2O/TiO2, Bi2O3/TiO2 and ZnMn2O4/TiO2 heterojunctions

Cu₂O/TiO₂, Bi₂O₃/TiO₂ and ZnMn₂O₄/TiO₂ heterojunctions were studied for potential applications in water decontamination technology and their capacity to induce an oxidation process under VIS light. UV–vis spectroscopy analysis showed that the junctions-based Cu₂O, Bi₂O₃ and ZnMn₂O₄ are able to absorb a large part of visible light (respectively, up to 650, 460 and 1000 nm). This fact was confirmed in the case of Cu₂O/TiO₂ and Bi₂O₃/TiO₂ by photocatalytic experiments performed under visible light. A part of the charge recombination that can take place when both semiconductors are excited was observed when a photocatalytic experiment was performed under UV–vis illumination. Orange II, 4-hydroxybenzoic and benzamide were used as pollutants in the experiment. Photoactivity of the junctions was found to be strongly dependent on the substrate. The different phenomena that were observed in each case are discussed.     

Charge transfer properties and photoelectrocatalytic activity of TiO2/MWCNT hybrid

The vertically aligned multiwalled carbon nanotube (MWCNT) arrays on tantalum foils were successfully coated with TiO₂ nanoparticles by a hydrothermal process. The prepared TiO₂/MWCNT hybrid was characterized by scanning electron microscopy and transmission electron microscopy. The charge transfer properties and photocatalytic degradation of rhodamine B with and without bias potential under UV irradiation were investigated. The MWCNTs promoted the separation of photoinduced carriers in the TiO₂, thus enhanced photocatalytic activity. Applying bias potential on the photoanode further enhanced its catalytic activity. The efficient charge transportation and high photoelectrocatalytic activity towards degradation of rhodamine B made this hybrid material promising for photocatalyst and for the development of photoelectrical devices.     

Preparation of polyaniline-modified TiO2 nanoparticles and their photocatalytic activity under visible light illumination

Titanium dioxide nanoparticles were modified by polyaniline (PANI) using ‘in situ’ chemical oxidative polymerization method in hydrochloric acid solutions. Powder X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infrared spectra (FT-IR), X-ray photoelectron spectroscopy spectrum (XPS) and UV–vis spectra were carried out to characterize the composites with different PANI contents. The photocatalytic degradation of phenol was chosen as a model reaction to evaluate the photocatalytic activities of the modified catalysts. Results show that TiO₂ nanoparticles are deposited by PANI to mitigate TiO₂ particles agglomeration. The modification does not alter the crystalline structure of the TiO₂ nanoparticles according to the X-ray diffraction patterns. UV–vis spectra reveal that PANI-modified TiO₂ composites show stronger absorption than neat TiO₂ under the whole range of visible light. The resulting PANI-modified TiO₂ composites exhibit significantly higher photocatalytic activity than that of neat TiO₂ on degradation of phenol aqueous solution under visible light irradiation (λ ≥ 400 nm). An optimum of the synergetic effect is found for an initial molar ratio of aniline to TiO₂ equal to 1/100.     

Low temperature preparation and visible light photocatalytic activity of mesoporous carbon-doped crystalline TiO2

A visible-light-active TiO₂ photocatalyst was prepared through carbon doping by using glucose as carbon source. Different from the previous carbon-doped TiO₂ prepared at high temperature, our preparation was performed by a hydrothermal method at temperature as low as 160 °C. The resulting photocatalyst was characterized by XRD, XPS, TEM, nitrogen adsorption, and UV–vis diffuse reflectance spectroscopy. The characterizations found that the photocatalyst possessed a homogeneous pore diameter about 8 nm and a high surface area of 126 m²/g. Comparing to undoped TiO₂, the carbon-doped TiO₂ showed obvious absorption in the 400–450 nm range with a red shift in the band gap transition. It was found that the resulting carbon-doped TiO₂ exhibits significantly higher photocatalytic activity than the undoped counterpart and Degussa P25 on the degradation of rhodamine B (RhB) in water under visible light irradiation (λ > 420 nm). This method can be easily scaled up for industrial production of visible-light driven photocatalyst for pollutants removal because of its convenience and energy-saving.     

Effect of formate and methanol on photoreduction/removal of toxic cadmium ions using TiO2 semiconductor as photocatalyst

Photoreduction/removal of cadmium was studied at pH 7 using TiO₂ Degussa as photocatalyst, and either formate or methanol as hole scavengers. In the absence of organic additives, approximately 60% of cadmium was found to be removed from the solution by adsorption. Addition of formate resulted in the photoreduction of cadmium to its metallic form. No cadmium reduction was observed when methanol was added as the hole scavenger. Zeta potential measurements of the catalyst suspensions and studies on the extent of organic additive adsorption and mineralisation were used to prove the photoreduction process. It was found that the adsorption of both cadmium and the organic hole scavenger is crucial for the photoreduction of cadmium. It is postulated that to be an effective hole scavenger the organic additive needs to be easily photooxidised under an anoxic environment. In addition, the presence of formate radicals could be responsible for the Cd photoreduction.     

The kinetics of photocatalytic degradation of trichloroethylene in gas phase over TiO2 supported on glass bead

In this investigation, a packed bed filled with coated titanium dioxide glass beads to study the kinetics of photocatalytic degradation of trichloroethylene under irradiation of 365 nm UV light. In the range of 100–500 ml/min of flowrate, the reaction rate for 6 μM TCE increased with an increasing flowrate upto 300 ml/min, while was not affected by the flowrate at the values higher than 300 ml/min. For moisture in the range of 9.4–1222.2 μM, the reaction rate of TCE was decreased with an increasing humidity. The adsorbed water on the catalyst surface could compete with the adsorption of TCE on the sites. The reaction rate of 6 μM TCE increased as the light intensity increased, and was proportional to the 0.61 order of the light intensity. Among the three L–H bimolecular form models, the experimental data had the best fit for one of models:

     

HIPed TiO2 dense pellets with improved photocatalytic performance

The effects of heating method and temperature on physical, structural and photocatalytic behaviors of TiO₂ pellets prepared by conventional heating and hot isostatic pressing have been evaluated. The pellets of submicron TiO₂ powders were heated to 600, 650, 700, 750 and 1000 °C using both processing methods in order to compare anatase to rutile phase transformation and densification behaviors. Bulk densities and porosities were calculated using the Archimedes method. XRD analysis were performed to calculate anatase/rutile ratios. Microstructures were characterized using SEM. Photocatalytic experiments have been performed under full spectrum irradiation. Degraded methylene blue samples were periodically monitored through UV–vis spectrophotometer to determine degradation kinetics. Anatase to rutile transformation is slightly faster and densification is better for lower temperatures for conventional heating, however HIPing gives better densification above 750 °C as it also retards rutile transformation. Mixed phase structures and HIPed samples showed the best photocatalytic performance which makes this method advantageous.     

Carbon-modified TiO2 photocatalyst by ethanol carbonisation

The new photocatalysts based on commercially available titanium dioxide powders: Tytanpol A11 (Police, Poland), pure anatase and P-25 (Degussa, Germany) containing about 20% rutile were modified by carbon via ethanol carbonisation. Titanium dioxides were heated at different temperature from 150 to 400 °C for 1 h in an atmosphere of ethanol vapour. The photocatalytic activity of carbon-modified TiO₂ was studied by oxidation of phenol in water under UV and artificial solar light irradiation. With increasing of carbon content in TiO₂ photocatalysts the activity for phenol decomposition under UV light was decreasing but that under visible light was stable. Turbidity of the slurry solution decreased with increasing of carbon content for all prepared photocatalysts because of the change of their surface character from hydrophilic to hydrophobic.     

Tubular V-free and V-doped TiO2 derived from H2Ti12O25 hollow spheres: Vapour-thermal synthesis,morphology evolution,and photocatalytic performance

Vanadium (V)-free and V-doped H₂Ti₁₂O₂₅ hollow spheres (HTOHSs) were first synthesised via vapour-thermal method at 290?°C using common chemicals and solvents, over super-critical temperature (243?°C) of ethanol (vapour source). Then, they were annealed at 600?°C under different processing conditions to obtain titanium dioxide (TiO₂) photocatalysts. All catalysts were characterised by means of XRD, SEM, TEM, XPS, UV–vis DRS, FT-IR, N₂ adsorbtion-desorbtion and fluorescence lifetime. Results indicated that after the treatment in air, V-free HTOHSs were transformed into open-ended hollow tubes with uniform length of ~5?µm and diameter of ~1?µm, and walls of hollow tubes consisted of aggregated nanosheets. Furthermore, HTOHS crystallised into anatase TiO₂ (white) phase. The treatment in N₂ atmosphere led to the breaking of longer tubes into shorter ones. In contrast, after the treatment in N₂ atmosphere or by reduction using NaBH₄ as a reductant, V-doped HTOHS resulted in the formation of anatase TiO₂ (black) samples and consisted of fewer tubes and more deformed spheres. In this study, fluorescence lifetime (τ) of photo-generated carriers corresponded well with the ratio of oxygen vacancy, indicating that oxygen vacancy dominates the lifetime even though it is very sensitive to many factors. The evolution of structure and morphology and photocatalytic mechanism were analysed and discussed.     

Photocatalytic degradation of Chromotrope 2R using nanocrystalline TiO2/activated-carbon composite catalysts

Composite catalysts made of nanocrystalline TiO₂ and carbon were prepared by a modified sol–gel method over activated carbon (AC). The composite catalysts were characterized by N₂ adsorption–desorption isotherm, TG, diffuse reflectance UV–vis spectroscopy, XRD and SEM. The photocatalytic activity was tested on the degradation of Chromotrope 2R (C2R) in aqueous medium under UV radiation. The composite catalysts exhibited higher activities than commercial Degussa P25 alone and the photocatalytic process was more efficient than the pure photolytic degradation. A modified Langmuir–Hinshelwood approach was used to study the kinetics and to determine the adsorption equilibrium constant and the reaction rate constant. Two different mechanisms are proposed and discussed in order to explain the observed synergy.     

Conversion of benzoic acid during TiO2-mediated photocatalytic degradation in water

The photocatalytic degradation of benzoic acid in water over Degussa P-25 TiO₂ suspensions was studied. UVA irradiation at 365 nm was supplied by a medium pressure mercury lamp providing 25 mW cm⁻² light intensity. Experiments were conducted at benzoic acid initial concentrations between 25 and 150 mg L⁻¹, catalyst loadings between 0.2 and 1 g L⁻¹ and initial solution pH values between 2 and 10.6. Conversion increased with increasing catalyst loading up to about 0.6 g L⁻¹ and it was favored at alkaline or neutral conditions but impeded at extremely acidic conditions. Increasing initial substrate concentration led to decreased benzoic acid conversion, which was found to follow a Langmuir–Hinshelwood kinetic expression. High performance liquid chromatography (HPLC) was employed to follow benzoic acid concentration profiles as well as to identify reaction by-products, while chemical oxygen demand (COD) and total organic carbon (TOC) analyses were carried out to assess the extent of mineralization. Benzoic acid hydroxylation by-products, namely 2-, 3- and 4-hydroxybenzoic acids as well as phenol were identified as reaction intermediates, although these contributed only a small fraction of the residual organic content. Although benzoic acid at 50 mg L⁻¹ was not ecotoxic to marine photobacteria Vibrio fischeri, its photodegraded solution exhibited substantial toxicity, which, however, proved not to be due to the identified intermediates.     

Photocatalytic reduction of selenium ions using different TiO2 photocatalysts

Comparative performance studies between different photocatalysts for reduction reactions are scarce. Here, Millennium PC500 and PC50 photoreactivities were investigated for selenite (Se(IV)) and selenate (Se(VI)) reduction to their elemental form (Se(0)) and compared with that of Degussa P25 TiO₂. Millennium PC500, with the highest surface area demonstrated the fastest photoreduction of Se(IV) and Se(VI), compared to P25 and Millennium PC50. Millennium PC50 and P25, which have comparable surface areas, showed similar photoreactivities. UV-Vis reflectance measurements and XRD characterisation revealed that the Se(0) deposits underwent phase transformation from amorphous to stable crystalline Se(0) during the drying and ageing process. Overall, the Millennium PCs appear to be promising photocatalysts for the photoreduction process.     

Photocatalytic degradation kinetics of di- and tri-substituted phenolic compounds in aqueous solution by TiO2/UV

In this study, photocatalytic degradation of 2,4,6-trimethylphenol (TMP), 2,4,6-trichlorophenol (TCP), 2,4,6-tribromophenol (TBP), 2,4-dimethylphenol (DMP), 2,4-dichlorophenol (DCP) and 2,4-dibromophenol (DBP) has been studied by TiO₂/UV. Although degraded phenolic compound concentration increased by increasing initial concentration photocatalytic decomposition rates of di- and tri-substituted phenols at 0.1–0.5 mM initial concentrations decreased when the initial concentration increased. The fastest degradation observed for TCP and the slowest for TMP. Photodegradation kinetics of the compounds has been explained in terms of Langmuir–Hinshelwood kinetics model. Degradation rate constants have been observed to be extremely depended on electronegativity of the substituents on phenolic ring. Degradation rate constant and adsorption equilibrium constant of TCP were calculated as k 0.0083 mM min⁻¹ and K 9.03 mM⁻¹. For TBP and TMP the values of k and K were obtained as 0.0040 mM min⁻¹, 19.20 mM⁻¹, and 0.0017 mM min⁻¹, 51.68 mM⁻¹, respectively. Degradation rate constant of DBP was similar as DCP (0.0029 mM min⁻¹ for DBP and 0.0031 mM min⁻¹ for DCP) whereas adsorption equilibrium constants differed (48.40 mM⁻¹ for DBP and 30.52 mM⁻¹ for DCP). K and k of DMP found as 83.68 mM⁻¹ and 0.0019 mM min⁻¹, respectively. The adsorption equilibrium constants in the dark were ranged between 1.11 and 3.28 mM⁻¹ which are lower than those obtained in kinetics. Adsorption constants have inversely proportion with degradation rate constants for all phenolic compounds studied.     

Photocatalytic transformations of aminopyrimidines on TiO2 in aqueous solution

In this paper, the effect of the presence of humidity and molecular oxygen on the low temperature oxidation of carbon monoxide on a Co₃O₄ powder surface was studied. The interaction between the probe molecules and the Co₃O₄ surface was investigated by means of diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy and quadrupolar mass spectrometry (QMS).

Carbon monoxide interacts with the Co₃O₄ surface and is converted to carbon dioxide at rather low temperature (T≥323 K); the formation of carbonate species is also evident. The reactivity of Co₃O₄ is strongly depressed by humidity: as a matter of fact, in steam conditions carbon monoxide oxidation is significant at temperatures higher than 523 K. Moreover, the formation of carbonate species is more evident than in dry conditions. The Co₃O₄ powder surface interacts with oxygen molecules at T≥323 K to originate several activated surface oxygen species. The activation with oxygen does not appear to facilitate significantly the formation of carbon dioxide.     

Influence of operating parameters on photocatalytic degradation of phenol in UV/TiO2 process

The use of hydrogen peroxide (H₂O₂) for improved photocatalytic degradation of phenol in aqueous suspension of commercial TiO₂ powders (Degussa P-25) was investigated. Photodegradation was compared using direct photolysis (UV alone), H₂O₂/UV, TiO₂/UV, and H₂O₂/TiO₂/UV processes in a batch reactor with high-pressure mercury lamp irradiation. The effects of operating parameters such as catalyst dosage, light intensity, pH of the solution, the initial phenol, and H₂O₂ concentrations on photodegradation process were examined. It was shown that photodegradation using H₂O₂/TiO₂/UV process was much more effective than using either H₂O₂/UV or TiO₂/UV process. The effect of the initial phenol concentration on TOC removal was also studied, demonstrating that more than 8 h was required to completely mineralize phenol into water and carbon dioxide. For all the four oxidation processes studied, photodegradation followed the first-order kinetics. The apparent rate constants with 400-W UV ranged from 5.0 × 10⁻⁴ min⁻¹ by direct photolysis to 1.4 × 10⁻² min⁻¹ using H₂O₂/TiO₂/UV process. The role of H₂O₂ on such enhanced photodegradation of phenol in aqueous solution was finally discussed.