不同热化学还原LiNbO3∶Ti或Mn晶体杂质电荷态和点缺陷

采用光学吸收和电子顺磁共振（ＥＳＲ）技术表征不同热化学还原ＬｉＮｂＯ３∶Ｔｉ，Ｍｎ（ＬＮ∶Ｔｉ，Ｍｎ）和纯的Ｌｉ／Ｎｂ＝０．９４５一致熔化ＬｉＮｂＯ３（ＬＮ）晶体的热力学还原习性。将ＬＮ∶Ｔｉ（厚度为１ｍｍ）样品放在Ｌｉ２ＣＯ３中、６００℃、保温７ｈ，产生６９０ｎｍ（～１．８ｅＶ，Ｔ＝６７％）和峰值靠近７８５ｎｍ（Ｔ＝７１％）的７７０～８１０ｎｍ光学吸收带，它们分别对应于Ｔｉ＾３＋的＾２Ｔ→＾２Ｅ     

金红石TiO2晶体中F和F+心电子结构及其吸收光谱研究

本文运用嵌入原子簇的电荷自洽离散变分方法（ＳＣＣ－ＤＶＭ－Ｘα方法）分别对ＴｉＯ２晶体中Ｆ和Ｆ＾＋心的能级结构进行计算,得到了Ｆ和Ｆ＾＋心的光学吸收跃迁模式,其跃迁能量分别是０．９８,１．７８ｅＶ,我们认为,经还原后的ＴｉＯ２晶体,在光吸收实验中测到的１．２μｍ（１．０２ｅＶ）,７６０ｎｍ（１．７５ｅＶ）两个峰分别是由于还原过程中形成的Ｆ和Ｆ＾＋心的吸收峰,并存在着Ｆ→Ｆ＾＋的转型过程。     

Li1+2x+yAlxNdyTi2-x-ySixP3-xO12系统的锂快离子导体研究

Ｌｉ１＋２ｘ＋ｙＡｌｘＮｄｙＴｉ２－ｘ－ｙＳｉｘＰ３－ｘＯ１２锂快离子导体可以用精选的天然高岭石Ａｌ４「Ｓｉ４Ｏ１０」（ＯＨ）８为起始原料，经与Ｌｉ２Ｃｏ３、ＴｉＯ２、ＮＨ４Ｈ２ＰＯ４进行高温（８００－１０００℃固相反应约２０ｈ而制得，一个空间群属于Ｒ３Ｃ的固溶体导电相可在ｙ＝０．５，ｘ≤０．３和ｙ＝１．０，ｘ≤０．４的组成范围内发现，该盯具有较好的电导性较低的活化能，起始组成ｙ＝１．０，ｘ＝０．     

BaMnZnCoTi-W型铁氧体微波吸收剂的制备和特性研究

对用Ｃｏ２＋、Ｔｉ４＋部分置换Ｆｅ３＋的Ｂａ（ＭｎＺｎ）ａＣｏｂＦｅ１６－ｙＣｏ２＋０．５ｙＴｉ４＋０．５ｙＯ２７－Ｗ型平面六角晶系微波铁氧体吸收剂的制备和特性进行了研究,并对其复介电常数的实部ε′和虚部ε″、磁导率的实部μ′和虚部μ″、损耗随微波频率、Ｃｏ２＋、Ｔｉ４＋含量、涂层厚度的变化作了测试和分析,发现当ｙ＝１．０时铁氧体的吸收性能最佳,其最佳厚度为１．４０ｍｍ,吸收衰减最大达２７．５ｄＢ。     

Fe73.5Cu1Mo3Si13.5B9微晶软磁合金的结构及其对磁性的影响

对Ｆｅ７３．５Ｃｕ１Ｍｏ３Ｓｉ１３．５Ｂ９微晶软磁合金的结构及其对合金磁性的影响了研究，结果表明，在最佳磁性能下，晶相点阵常数ａ＝０．２８４３ｎｍ，相当于Ｆｅ（Ｓｉ）固溶体中含Ｓｉ％（ｍｏｌ／ｍｏｌ）：１８－２０，体积百分数Ｖ＝７４．８％，晶粒尺寸Ｄ＝１４．６ｎｍ；残余非晶层厚度δ＝１．２３ｎｍ；当Ｔ退火≥５６０℃时明显有Ｆｅ－Ｂ化合物析出。Ｆｅ７３．５Ｃｕ１Ｍｏ３Ｓｉ１３．５Ｂ９合金的磁性不仅与     

氧缺位铁酸盐MFe2O4—δ的制备条件研究

使用ＸＲＤ、Ｍｏｓｓｂａｕｅｒ谱结合化学分析考查了５７３Ｋ下还原时间对空气氧化碱性悬浮液合成的铁酸盐ＭＦｅ２Ｏ４＋δ（δ≥０）的物相、晶格常数及化学组成的影响，得出了制备氧缺位铁酸盐ＭＦｅ２Ｏ４－δ（δ＞０）的最佳条件。结果表明，在５７３Ｋ下制备ＭＦｅ２Ｏ４－δ的最佳还原时间按Ｆｅ、Ｃｏ、Ｍｎ、Ｎｉ顺序分别为１０ｈ、３ｈ、４０ｍｉｎ和３０ｍｉｎ，氧缺位程度及晶格常数在最佳还原时间之前随还原时间增长而增大，在接近最佳还原时间时达到极大值。ＭＦｅ２Ｏ４－δ的极大值δ按Ｆｅ、Ｃｏ、Ｍｎ、Ｎｉ顺序减小，超过最佳还原时间ＭＦｅ２Ｏ４－δ将分解为α－Ｆｅ（Ｍ＝Ｆｅ）或ＭＯ－ＦｅＯ（Ｍ＝Ｃｏ、Ｍｎ、Ｎｉ）。     

八种新功能晶体的比热及其与相变掺杂物关系的实验研究

本文对八种新型功能晶体Ｌｉ２Ｂ４Ｏ７、Ｂｉ１２ＴｉＯ２０、Ｂｉ１２ＧｅＯ２０、Ｂｉ１２ＧｅＯ２０、Ｂｉ４Ｇｅ３Ｏ１２、Ｓｒ１－ｘＢａｘＮｂ２Ｏ６（ｘ＝０．３３，０．４８）、ＬｉＴａＯ３等在１３０～９７３Ｋ范围内的比热行为及其与相变、组分之间的关系进行了实验研究，给出了比热的多项式拟合方程，并与用纽曼－卡普定律及用Ｗｉｋｅｌｍａｎｎ经验方程的比热计算值作了对比，为晶体比热的估算提供了依据和方法。     

Al—5Fe—2Ni合金析出相的Mossbauer谱

用Ｍｏｓｓｂａｕｅｒ谱学和ＸＲＤ方法研究了快速凝固Ａｌ－５Ｆｅ－２Ｎｉ（原子百分数）合金的析出相，结果表明，析出相为三元化合物Ａｌ９ＦｅｘＮｉ２－ｘ（０〈ｘ〈２）属于单斜晶系，晶格参数ａ＝０．８５８ｎｍ，ｂ＝０．６３１ｎｍ，ｃ＝０．６２１ｎｍ，β＝９４．８，它的Ｍｏｓｓｂａｕｅｒ谱为一套双线，同质异能移位ＩＳ＝０．１２ｍｍ．ｓ＾－１，四极分别ＱＳ＝０．３２ｍｍ．ｓ＾－１，线宽Г＝０．２６ｍｍ．ｓ＾     

LiNiO2热分解反应动力学研究

用ＤＴＡ和ＸＲＤ研究了ＬｉＮｉＯ_２在空气中的热分解过程为：ＬｉＮｉＯ_２（ｓ）→(６５０～７２０℃)Ｌｉ_２Ｎｉ_８Ｏ_{１０（ｓ）}＋４Ｌｉ_２Ｏ_（ｓ）＋Ｏ_２（ｇ）→(８５０～９５０℃)Ｌｉ_２Ｏ_（ｓ）＋８ＮｉＯ_（ｓ）＋１／２Ｏ_２（ｇ） →(１０００～１１５０℃)ＮｉＯ（ｓ）＋Ｌｉ_２Ｏ_（ｇ）用 Ｄｏｙｌｅ－Ｏｚａｗａ法和 Ｋｉｓｓｉｎｇｅｒ法计算了各反应阶段的表观活化能分别为 ７４７．１８±１．０ ｋＪ·ｍｏｌ^－１、９３２．４６±１．０ ｋＪ·ｍｏｌ^－１和 １１２６．９７±１．０ ｋＪ·ｍｏｌ^－１．用 Ｋｉｓｓｉｎｇｅｒ法确定了反应级数和频率因子,确定了三个阶段的动力学方程分别为 ｄα／ｄt＝１．７３６ｘ１０３９ｅ^{－９００００／Ｔ}（１－α）^{１．０５７}; ｄα／ｄｔ＝１８０６×１０^３９ｅ^{－１１１５００／Ｔ}（１－α）^{０．８４４};ｄα／ｄｔ＝４．２６２×１０４２ｅ^{－１３５０００／Ｔ}（１－α）^{１．２７５}     

THE ORDERING OF THE α-Fe(Si)PHASE IN Fe_(73.5)Cu_1Nb_3Si_(13.5)B_9 ANNEALED ALLOY

用ＸＲＤ法研究了退火Ｆｅ７３．５Ｃｕ１Ｎｂ３Ｓｉ１３．５Ｂ９合金中α－Ｆｅ（Ｓｉ）晶化相的有序化过程，结果表明，Ｆｅ７３．５Ｃｕ１Ｎｂ３Ｓｉ１３．５Ｂ９非晶合金在４９０℃，１ｈ退火后，α－Ｆｅ（Ｓｉ）晶化相是具有ＤＯ３结构的有序相，有序畴为球形，直径为７．０ｎｍ，它随退炎温度的升颃是长大，在５９０℃退火后达１０．９ｎｍ，与α－Ｆｅ（Ｓｉ）的尺寸相当，此时α－Ｆｅ（Ｓｉ）的有序度为０．８，在８５０℃     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.