Symmetric three-guide optical coupler with nonidentical center and outside guides

To obtain maximum power transfer efficiency from one outside guide to another in a three-guide coupler, the differences among the propagation constants of the three propagating modes must be equal, i.e.,beta_{A} - beta_{C}must equalbeta_{C} - beta_{B}. This is not the case when all three guides are identical. By increasing either the width or index of the center guide relative to the outside guides, the differences between the propagation constants can be made equal. This can result in a significant increase in power transfer from one outside guide to the other. With equal spacing between the propagation constants of the modes, overall power transfer efficiency is limited only by radiation losses at the input and output of the three-guide coupler, due to the imperfect match between the mode shape of the input and output guides and the shape of the linear combination of the three modes of the coupler which best matches it. For couplers with reasonable guide spacing to guide width ratiosSand reasonable confinement, this loss is usually small, and power transfer efficiencies for power transfer from one outside guide to another can approach 100 percent. For example, with correctly adjusted β's, power transfer efficiency in a three-guide coupler withS = 1can be as high as 99.8 percent. Even withS = 0.5, efficiencies can be as high as 97.8 percent.     

Single-mode optical waveguides and phase modulators in the InP material system

The characteristics of several different single-mode optical waveguides in the InP material system are discussed. Slab-coupled rib waveguides in GaInAsP (lambda_{gap} approx 1 mum) epitaxial layers grown on InP have shown propagation losses as low as 1.7 cm^-1at 1.3 μm and 2.7 cm^-1at 1.15 μm. Oxide-confined InP rib guides fabricated using a lateral overgrowth technique have losses of about 1.5 cm^-1at 1.15 μm. Three-guide couplers have been made by fabricating three parallel oxide-confined guides in close proximity. InP p+-n-n+ guides capable of modulating TE-polarized radiation have been fabricated using epitaxial techniques and Be-ion implantation. By measuring the phase difference between the TE-like and TM-like modes as a function of applied voltage, an estimate of the r41electrooptic coefficient in InP at 1.3 μm that is in good agreement with a previously reported value was obtained. Guides of this type should find use as the active components in InP switches and interferometers.     

Limitations on power-transfer efficiency in three-guide optical couplers

The eigenvalue equations for a slab three-guide coupler were solved and the power-transfer efficiency was calculated when the coupler is used as 1) a power divider and 2) to transfer power from one outside guide to another. In the first case, two modes take part in the power transfer, and unless the guides are very tightly coupled, periodic beats with high power transfer are obtained at multiples of the coupling length as in a two-guide coupler. In the second case, three modes take part in the power transfer, and periodic beats and high power-transfer efficiency can only be obtained if the propagation velocities of the three modes are related to each other in a simple way. This condition will occur only if the guides of a three-guide coupler made up of identical guides are much more loosely coupled than guides generally used in a two-guide coupler.     

The design of a mode selective directional coupler for a high power gyroklystron†

The design method of mode selective directional couplers from a transverse electric mode in a circular waveguide to the fundamental mode in a rectangular wave guide is presented in this paper. The design results for a TE₀₁ circular mode coupler intended for use in the output power measurement of a high power gyroklystron are reported; these results indicate that more than 50-80dB directivity and sufficient suppression of unwanted modes can be obtained with a coupler less than 07m in length. The effects of frequency and rectangular wave guide size on coupler parameters are also discussed in this paper     

Top-Wall and Branch-Waveguide Hybrids for Millimeter Wavelengths (Correspondence)

Top-wall and multiple-branch waveguide couplers were developed as hybrid junctions for millimeter wavelengths, and their electrical characteristics were measured. For construction of the 55-GHz top-wall coupler, electroforming techniques were used; for the 94-GHz branch-guide coupler, the branch lines were cut directly into the wall of the main guide. Copper losses were less than 0.2 dB for the two types of couplers.     

Broad-band high-silica optical waveguide star coupler withasymmetric directional couplers

A broadband optical waveguide star coupler with asymmetric directional couplers is proposed. A coupling or splitting ratio of the coupler is flattened with respect to wavelength by choosing appropriate values for Δβ and complete power transfer length. The wavelength characteristics of uniform and alternating Δ&thetas;b directional couplers are investigated, and their broadband operation is shown theoretically. To demonstrate the feasibility of the new proposal, 8×8 star couplers composed of such asymmetric directional couplers are fabricated by using high-silica waveguides on a silicon chip. A star coupler composed of asymmetric directional couplers exhibited 2-dB loss variation in the wavelength range of 1.3-1.55 μm, and this value was almost one fourth of that of a star coupler composed of symmetric directional couplers     

Characteristics of S-shaped waveguide structures by the annealedproton exchange process in LiNbO3

The loss of S-shaped waveguide bends in annealed proton-exchanged LiNbO₃ integrated optical devices is found to be dependent on the length of thermal annealing time. The minimum transition length required in order to have losses as low as 0.2 dB is 2.0 mm for a 0.1-mm lateral offset. Intersecting waveguides based on S-shaped structures have been characterized for passive crossovers. An angle greater than 6° is required to provide a crosstalk of less than -30 dB. At a particular angle, intersecting waveguides offer the possibility of making a 3-dB coupler if an insertion loss of 1.2 dB is not a big concern. Zero-gap couplers based on S-shaped structures have been characterized for applications as 3-dB couplers as well. This type of 3-dB coupler has a much lower insertion loss of roughly 0.4-0.5 dB. Both 3-dB intersecting waveguides and 3-dB zero-gap couplers are less sensitive to wavelength variations     

Power switching in hybrid coherent couplers

We report on a theoretical and numerical investigation of the switching of power in new hybrid models of nonlinear coherent couplers consisting of optical slab waveguides with various orders of nonlinearity. The first model consists of two guides with second-order instead of the usual third-order susceptibilities as typified by the Jensen coupler. This second-order system is shown to have a power self-trapping transition at a critical power greater than the third-order susceptibility coupler. Next, we consider a mixed coupler composed of a second-order guide coupled to a third-order guide and show that, although it does not display a rigorous self-trapping transition, for a particular choice of parameters it does show a fairly abrupt trapping of power at a lower power than in the third-order coupler. By coupling this mixed nonlinear pair to a third, purely linear guide, the power trapping can be brought to even lower levels and in this way a satisfactory switching profile can be achieved at less than one sixth the input power needed in the Jensen coupler     

硅基波导光栅耦合器与波导传输损耗的研究

对硅(Si)基波导光栅耦合器的设计与耦合性能进 行了研究。采用本征模展开法对光栅耦合器进行设计与 优化,通过实验测量了光栅的耦合性能,并对均匀光栅、自聚焦光栅和反射光栅等3种光栅 耦合器的耦合 性能进行了比较,耦合效率分别达到了达到47.86、56. 36和48.98%,自聚焦光栅可以有效改善光纤到 光纤的传输效果,耦合效率提高了8.5%。通过实验测量了基于耦合光 栅技术的Si基条形波导和槽型波导的 传输损耗,结果显示,条形波导和槽型波导的传输损耗分别为2.34d B/cm和6.31dB/mm。     

The design of triple rib waveguide couplers by the discretespectral index method

The operations of three-guide couplers are usually controlled by the width and refractive index of the guides. However, when rib waveguides are used in three-guide couplers and power dividers, we propose to use the dimensions of the ribs as the governing parameters instead. Formulating a new transcendental equation using the discrete spectral index (DSI) method, triple rib waveguide couplers are accurately analyzed for the first time. The new accurate and fast analysis of triple rib waveguides shows that the propagation constants of the various modes are dominantly controlled by the height of the middle rib. A systematic and simple procedure is consequently introduced to design quasi-transverse electric (TE) polarized triple rib waveguide couplers, which ensures maximum power transfer from one outermost guide to the other outermost guide. For triple rib power dividers, the height of the middle rib is found to control the amount of power that can be transferred from the excited middle rib waveguide to the two outer rib waveguides. Maximum power division is achieved when the three ribs of the waveguide are identical     

Antennas and waveguides for far-infrared integrated circuits

Antennas and waveguides for the wavelength range 0.1-3 mm are considered. Emphasis is placed on those designs which lend themselves to integration with each other and with other components such as diodes. The general properties of FIR antennas are reviewed. A novel silicon waveguide antenna is discussed, and its design, simulation, fabrication, and performance at 119 μm are described. This antenna has a highly symmetrical, single-lobed beam with 3 dB beamwidths of 35 and 38° in theE- andH-planes, respectively. The gain (measured in microwave simulation) is 12.8 dB. This antenna is well suited for integration with Schottky diodes. The related subject of FIR waveguides is discussed. Experiments with metal transmission lines at 119 μm are described and dielectric guides related to the waveguide antenna are also considered. Using components such as these it may soon be possible to construct receiver front ends for this wavelength range in integrated-circuit form.     

非对称GNRD波导耦合特性的计算

本文将两种尺寸不同的波导相互耦合可实现宽带耦合器的原理用于GNRD波导定向耦合器的设计。根据对非对称GNRD波导耦合特性的理论分析,定性讨论了各种非对称情况对耦合特性的影响;并设计了3dB GNRD波导非对称定向耦合器。计算结果表明其在8mm波段,耦合频带比原对称时的明显平坦。     

Cross power and crosstalk in waveguide couplers

The operation of two-guide couplers is re-examined to include the effects of cross power. Two two-guide coupler structures that operate as on-off switches are analyzed using both the exact eigenmodes of a slab model of the coupler and a coupled-mode theory that takes cross-power effects into account. The two coupler configurations analyzed are with the output guide on the same side as the input guide and on the side of the coupled guide. For the proper choice of the length of the coupler in the first case, the waveguide detuning can be adjusted so that ideal switching behavior can be achieved. For the second case, full on-off switching is not possible. Excellent agreement is found between results of the coupled-mode theory and exact slab analyses     

Design of Dielectric Ridge Waveguides for Millimeter-Wave Integrated Circuits

All-dielectric ridge waveguides may be useful as elements of millimeter- and submillimeter-wave integrated circuits; A planar metallic V-coupler can be used to couple energy between the guide and small circuit elements such as diodes. Desirable characteristics in such a guide/coupler system are a) quasi-single mode propagation; b) low radiation loss in bendy c) low coupling loss between guide and devices and d) adequate physical strength. In this paper, we discuss the general problem of designing guides and couplers to obtain the desired characteristics. The principal method used is simulation in the range 2-7 GHz. We find that with good compromise designs, typical coupling loss between waveguide and a small device is about 1.4 dB, exclusive of dielectric loss and ohmic loss in the coupler.     

Folded Half Mode Substrate Integrated Waveguide 3 dB Coupler

In this letter, novel compact 3 dB double-slot and single-slot couplers are proposed and implemented based on folded half mode substrate integrated waveguide (FHMSIW). The size of the FHMSIW coupler is reduced by nearly 50% and 75% compared with half-mode substrate integrated waveguide coupler and substrate integrated waveguide coupler, respectively. Prototype couplers at X-band are fabricated and measured and good performance in bandwidth, insertion loss, and balance are achieved.      

Narrow-band directional couplers made of dissimilar single-modefibers with different cladding refractive indexes

A wavelength-selective directional coupler, consisting of two polished single-mode fibers with different cladding refractive indexed, has been fabricated. In contrast to symmetrical couplers, where the power transfer characteristic is a quasiperiodic function of the wavelength, couplers made of dissimilar fibers show a true bandpass-filter characteristic. They consist of two fibers with different core diameters and refractive-index profiles, having the same cladding refractive index. The parameters of the fibers must be chosen in such a way that if their propagation constants β₁, β₂ are plotted over the wavelength, the curves intersect at a cross-over wavelength λ₀ equal to the center wavelength of the filter. The 3-dB bandwidth of the coupler's power transfer characteristic is 13.6 nm, the best value achieved up to now     

新型圆形槽波导定向耦合器

圆形槽波导是一种新型的高功率毫米波、亚毫米波传输线.为了实现圆形槽波导之间的耦合,本文根据双槽波导的耦合机理,设计出了新型圆形槽波导走向耦合器,并计算了3dB圆形槽波导定向耦合器的频率特性.     

Coupling ratio control of polymeric waveguide couplers by bending

Directional couplers are successfully fabricated on acrylic substrates using polymers synthesised from deuterated methacrylate and deuterated fluoromethacrylate monomers. The excess loss of a 50 mm long coupler is about 0.7 dB including waveguide and fibre coupling losses. A novel method is proposed for tuning the coupling ratio. By bending the coupler, high precision control of within 1% is attained without optical polarisation dependence.<>     

Milled-groove method for fiber-to-waveguide couplers

We report a simple milled-groove process integrated with a two-step ion-diffused waveguide fabrication for efficient coupling between single-mode fibers and integrated optical waveguides andY- branches. We demonstrate such a coupling technique using a) a multimode transition to single-mode waveguide coupler, and b) an integrated optical 3-dB branching waveguide coupler from a single-mode fiber to silver/sodium ion-enchanged waveguide components. The coupling loss was about 1-2 dB over a propagation length of 2 cm at an operating wavelength of 633 nm.