Simulated economics assessment of hollow fiber CO<Subscript>2</Subscript> separation modules

Various conditions under which the hollow fiber membrane separation system would be the optimal selection are investigated in terms of cost effectiveness. Numerical simulation is carried out to examine the effects of different configurations such as single-stage, two-stage and three-stage CO₂ separation processes. In particular, the hollow fiber membrane processes for CO₂ separation with vacuum pumps, heat exchangers, coolers and compressors to provide pressurized feed streams are analyzed. Operating costs are evaluated and compared numerically for the processes with and without recycle streams to compare feasibility for commercial implementation while maintaining the purity and recovery ratio as high as possible.     

Effect of water pretreatment on CO<Subscript>2</Subscript> capture using a potassium-based solid sorbent in a bubbling fluidized bed reactor

A bubbling fluidized bed reactor was used to study CO₂ capture from flue gas by using a potassium-based solid sorbent, sorbKX35 which was manufactured by the Korea Electric Power Research Institute. A dry sorbent, sorbKX35, consists of K₂CO₃ for absorption and supporters for mechanical strength. To increase initial CO₂ removal, some amount of H₂O was absorbed in the sorbent before injecting simulated flue gas. It was possible to achieve 100% CO₂ removal for more than 10 minutes at 60°C and a residence time of 2 s with H₂O pretreatment. When H₂O pretreatment time was long enough to convert K₂CO₃ of sorbKX35 into K₂CO₃ · 1.5H₂O, CO₂ removal was excellent. The results obtained in this study can be used as basic data for designing and operating a large scale CO₂ capture process with two fluidized bed reactors. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Performance of Ni catalyst supported on La-hexaaluminate in CO<Subscript>2</Subscript> reforming of CH<Subscript>4</Subscript>

CO₂ reforming of CH₄ was performed using Ni catalyst supported on La-hexaaluminate which has been an well-known material for high-temperature combustion. La-hexaaluminate was synthesized by sol-gel method at various conditions where different amount of Ni (5–20 wt%) was loaded. Ni/La-hexaaluminate experienced 72 h reaction and its catalytic activity was compared with that of Ni/Al₂O₃, Ni/La-hexaaluminate shows higher reforming activity and resistance to coke deposition compared to the Ni/Al₂O₃ model catalyst. Coke deposition increases proportionally to Ni content. Consequently, Ni(5)/La-hexaaluminate(700) is the most efficient catalyst among various Ni/La-hexaaluminate catalysts regarding the cost of Ni in Ni(X)/La-hexaaluminate catalysts. BET surface area, XRD, EA, TGA and TPO were performed for surface characterization. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Optimization of CO2 capture process with aqueous amines using response surface methodology

Amine is one of candidate solvents that can be used for CO₂ recovery from the flue gas by conventional chemical absorption/desorption process. In this work, we analyzed the impact of different amine absorbents and their concentrations, the absorber and stripper column heights and the operating conditions on the cost of CO₂ recovery plant for post-combustion CO₂ removal. For each amine solvent, the optimum number of stages for the absorber and stripper columns, and the optimum absorbent concentration, i.e., the ones that give the minimum cost for CO₂ removed, is determined by response surface optimization. Our results suggest that CO₂ recovery with 48 wt% DGA requires the lowest CO₂ removal cost of $43.06/ton of CO₂ with the following design and operating conditions: a 20-stage absorber column and a 7-stage stripper column, 26 m³/h of solvent circulation rate, 1903 kW of reboiler duty, and 99°C as the regenerator-inlet temperature.     

Techno-economic evaluation of a PVAm CO2-selective membrane in an IGCC power plant with CO2 capture

Published data for an operating power plant, the ELCOGAS 315 MWe Puertollano plant, has been used as a basis for the simulation of an integrated gasification combined cycle process with CO₂ capture. This incorporated a fixed site carrier polyvinylamine membrane to separate the CO₂ from a CO-shifted syngas stream. It appears that the modified process, using a sour shift catalyst prior to sulphur removal, could achieve greater than 85% CO₂ recovery at 95 vol% purity. The efficiency penalty for such a process would be approximately 10% points, including CO₂ compression. A modified plant with CO₂ capture and compression was calculated to cost €2320/kW, producing electricity at a cost of 7.6 € cents/kWh and a CO₂ avoidance cost of about €40/tonne CO₂.     

Techno-economic assessment of pulverized coal boilers and IGCC power plants with CO<Subscript>2</Subscript> capture

The current studies on power plant technologies suggest that Integrated Gasification Combined Cycle (IGCC) systems are an effective and economic CO₂ capture technology pathway. In addition, the system in conventional configuration has the advantage of being more “CO₂ capture ready” than other technologies. Pulverized coal boilers (PC) have, however, proven high technical performance attributes and are economically often most practical technologies. To highlight the pros and cons of both technologies in connection with an integrated CO₂ capture, a comparative analysis of ultrasupercritical PC and IGCC is carried out in this paper. The technical design, the mass and energy balance and the system optimizations are implemented by using the ECLIPSE chemical plant simulation software package. Built upon these technologies, the CO₂ capture facilities are incorporated within the system. The most appropriate CO₂ capture systems for the PC system selected for this work are the oxy-fuel system and the postcombustion scheme using Monoethanolamine solvent scrubber column (MEA). The IGCC systems are designed in two configurations: Water gas shift reactor and Selexol-based separation. Both options generate CO₂-rich and hydrogen rich-gas streams. Following the comparative analysis of the technical performance attributes of the above cycles, the economic assessment is carried out using the economic toolbox of ECLIPSE is seamlessly connected to the results of the mass and energy balance as well as the utility usages. The total cost assessment is implemented according to the step-count exponential costing method using the dominant factors and/or a combination of parameters. Subsequently, based on a set of assumptions, the net present value estimation is implemented to calculate the breakeven electricity selling prices and the CO₂ avoidance cost.     

Techno-economic optimization of IGCC integrated with utility system for CO2 emissions reduction—Maximum power production in IGCC

Environmental legislation, with its increasing pressure on the energy sector to control greenhouse gases, is a driving force to reduce CO₂ emissions. In this paper, pre-combustion CO₂ capture through integration of a site utility system with an integrated gasification combined cycle (IGCC) is investigated as an option to provide a compressed CO₂-rich stream from a process site for sequestration. This work presents a two-step procedure for integration and optimization of a site utility system with an IGCC plant: (i) screening and optimization of IGCC plant performance parameters; (ii) integration and optimization of the utility system of the site with the IGCC plant. In the first step, an optimization approach applies the results of screening studies based on rigorous simulation of the IGCC. Having fixed the inlet fuel flow rate, the IGCC design parameters (including oxygen consumption, diluent flow rate and turbine exit pressure) are optimized for maximum power generation. Energy flows between the IGCC and CO₂ compression train are considered. In the second step, the economic and operating performance of the utility system integrated with the IGCC plant are modeled and optimized for minimum operating cost to find the most appropriate level of integration. In a case study illustrating the approach, 94% of the fuel is gasified; additional power generation offsets the operating costs of pre-combustion CO₂ capture.     

A Single Stage Membrane Process for CO2 Capture from Flue Gas by a Facilitated Transport Membrane

Carbon dioxide is the most important anthropogenic greenhouse gas and it accounts for about 80% of all greenhouse gases (GHG). The global atmospheric CO₂ concentrations have been increased significantly and have become the major source responsible for global warming; the greatest environmental challenge the world is facing now. The efforts to control the GHG emissions include the recovery of CO₂ from flue gas. In this work, feasibility analysis, based on a single stage membrane process, has been carried out with an in-house membrane program interfaced within process simulation program (AspenHysys) to investigate the influence of process parameters on the energy demand and flue gas processing cost. A novel CO₂-selective membrane with the facilitated transport mechanism has been employed to capture CO₂ from the flue gas mixtures. The results show that a membrane process using the facilitated transport membrane can also be considered as an alternative CO₂ capture process and it is possible to achieve more than 90% CO₂ recovery and 90% CO₂ purity in the permeate with reasonable energy consumption compared to amine absorption and other capture techniques.     

Efficient pressure swing adsorption for improving H<Subscript>2</Subscript> recovery in precombustion CO<Subscript>2</Subscript> capture

An efficient design for pressure swing adsorption (PSA) operations is introduced for CO₂ capture in the pre-combustion process to improve H₂ recovery and CO₂ purity at a low energy consumption. The proposed PSA sequence increases the H₂ recovery by introducing a purge step which uses a recycle of CO₂-rich stream and a pressure equalizing step. The H₂ recovery from the syngas can be increased over 98% by providing a sufficient purge flow of 48.8% of the initial syngas feeding rate. The bed size (375m³/(kmol CO₂/s)) and the energy consumption for the compression of recycled CO₂-rich gas (6 kW/(mol CO₂/s)) are much smaller than those of other PSA processes that have a CO₂ compression system to increase the product purity and recovery.     

The effect of ethane on the performance of commercial polyphenylene oxide and Cardo-type polyimide hollow fiber membranes in CO<Subscript>2</Subscript>/CH<Subscript>4</Subscript> separation applications

Impurities such as hydrogen sulfide, water vapor and heavy hydrocarbons in natural gas have considerable effects on the membrane performance. Small amounts of condensable and polymer soluble components in the feed gas cause swelling or plasticization of glassy membranes, leading to a reduction in membrane selectivity. In the present research the influence of ethane was investigated on the permeance and selectivity of two commercially available hollow fiber membranes, namely Cardo-type polyimide and PPO hollow fibers for CO₂/CH₄ separations. It was concluded that the gas mixture permeation rate was increased in the presence of C₂H₆. However, the CO₂/CH₄ separation factors remained almost the same in the presence and absence of the C₂H₆.     

Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hollow spheres and their activity in methylene blue photodecomposition

PSA [poly-(styrene-methyl acrylic acid)] latex particle has been taken into account as template material in SiO₂ hollow spheres preparation. TiO₂-doped SiO₂ hollow spheres were obtained by using the appropriate amount of Ti(SO₄)₂ solution on SiO₂ hollow spheres. The photodecomposition of the MB (methylene blue) was evaluated on these TiO₂-doped SiO₂ hollow spheres under UV light irradiation. The catalyst samples were characterized by XRD, UV-DRS, SEM and BET. A TiO₂-doped SiO₂ hollow sphere has shown higher surface area in comparison with pure TiO₂ hollow spheres. The 40 wt% TiO₂-doped SiO₂ hollow sphere has been found as the most active catalyst compared with the others in the process of photodecomposition of MB (methylene blue). The BET surface area of this sample was found to be 377.6 m²g⁻¹. The photodegradation rate of MB using the TiO₂-doped SiO₂ catalyst was much higher than that of pure TiO₂ hollow spheres.     

Absorption of SO<Subscript>2</Subscript> using PVDF hollow fiber membranes with PEG as an additive

In this study, removal of SO₂ from gas stream was carried out by using microporous polyvinylidene fluoride (PVDF) asymmetric hollow fiber membrane modules as gas-liquid contactor. The asymmetric hollow fiber membranes used in this study were prepared polyvinylidene fluoride by a wet phase inversion method. Water was used as an internal coagulant and external coagulation bath for all spinning runs. An aqueous solution containing 0.02 M NaOH was used as the absorbent. This study attempts to assess the influence of PEG additive, absorbent flow rate, SO₂ concentration, gas flow rate and gas flow direction on the SO₂ removal efficiency and overall mass transfer coefficient. The effect of liquid flow rate on SO₂ removal efficiency shows that at very low liquid flow rate, the NaOH available at the membrane surface for reacting with SO₂ is limited due to the liquid phase resistance. As liquid flow rate is above the minimum flow rate which overcomes the liquid phase resistance, the SO₂ absorption rate is controlled by resistance in the gas phase and the membrane. The SO₂ absorption rate with inlet SO₂ concentration was sharply increased by using hollow fiber membranes compared to a conventional wetted wall column because the former has higher gas liquid contacting area than the latter. The mass transfer coefficient is independent of pressure. When the gas mixture was fed in the shell side, the removal efficiency of SO₂ declined because of channeling problems on the shell side. Also, the addition of PEG in polymer dopes increased SO₂ removal efficiency. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Conceptual feasibility studies of a CO<Subscript><Emphasis Type="Italic">X</Emphasis></Subscript>-free hydrogen production from ammonia decomposition in a membrane reactor for PEM fuel cells

CO_X-free hydrogen production from ammonia decomposition in a membrane reactor (MR) for PEM fuel cells was studied using a commercial chemical process simulator, Aspen HYSYS®. With process simulation models validated by previously reported kinetics and experimental data, the effect of key operating parameters such as H₂ permeance, He sweep gas flow, and operating temperature was investigated to compare the performance of an MR and a conventional packed-bed reactor (PBR). Higher ammonia conversions and H₂ yields were obtained in an MR than ones in a PBR. It was also found that He sweep gas flow was favorable for X_NH3 enhancement in an MR with a critical value (5 kmol h^-1), above which no further effect was observed. A higher H₂ permeance led to an increased H₂ yield and H₂ yield enhancement in an MR with the reverse effect of operating temperature on the enhancement. In addition, lower operating temperature resulted in higher X_NH3 enhancement and H₂ yield enhancement as well as NG cost savings in a MR compared to a conventional PBR.     

Techno-economic evaluation of gas separation processes for long-term operation of CO<Subscript>2</Subscript> injected enhanced coalbed methane (ECBM)

Energy source diversification through development of coalbed methane (CBM) resources is one of the key strategies to make a country less dependent on simple energy resources (e.g., crude oil, natural gas, nuclear energy etc.). Especially, enhanced coalbed methane (ECBM) technology can be expected to secure the resources as well as environmental benefits. However, the raw CBM gas obtained from CO₂ ECBM contains a considerable amount of CO₂, and the CO₂ content increases depending on the operation time of the facility. Considering the changes of the CBM composition, we developed process simulations of the CBM separation & purification processes based on the amine absorption to meet the design specifications (CH₄ purity of product stream: 99%, CH₄ recovery rate: 99%) with different CBM feed gas conditions. Using the developed simulation model, we performed an economic evaluation using unit methane production cost (MPC) considering coal-swelling types and facility operation time, and established an operation strategy under different natural gas market scenarios.     

Dynamic modeling of CO2 absorption from coal-fired power plants into an aqueous monoethanolamine solution

Among carbon capture and storage (CCS), the post-combustion capture of carbon dioxide (CO₂) by means of chemical absorption is actually the most developed process. Steady state process simulation turned out as a powerful tool for the design of such CO₂ scrubbers. Besides steady state modeling, transient process simulations deliver valuable information on the dynamic behavior of the system. Dynamic interactions of the power plant with the CO₂ separation plant can be described by such models. Within this work a dynamic process simulation model of the absorption unit of a CO₂ separation plant was developed. For describing the chemical absorption of CO₂ into an aqueous monoethanolamine solution a rate based approach was used. All models were developed within the Aspen Custom Modeler^® simulation environment. Thermo physical properties as well as transport properties were taken from the electrolyte non-random-two-liquid model provided by the Aspen Properties^® database. Within this work two simulation cases are presented. In a first simulation the inlet temperature of the flue gas and the lean solvent into the absorber column was changed. The results were validated by using experimental data from the CO₂SEPPL test rig located at the Dürnrohr power station. In a second simulation the flue gas flow to the separation plant was increased. Due to the unavailability of experimental data a validation of the results from the second simulation could not be achieved.     

Optimal operation of the pressure swing adsorption (PSA) process for CO<Subscript>2</Subscript> recovery

The operation of PSA (Pressure Swing Adsorption) processes is a highly nonlinear and challenging problem. We propose a systematic procedure to achieve the optimal operation of a PSA process. The model of the PSA process for CO₂ separation and recovery is developed first and optimization is performed to identify optimal operating conditions based on the model. The effectiveness of the model developed is demonstrated by numerical simulations and experiments using CO₂ and N₂ gases and zeolite 13X. Breakthrough curves and temperature changes in the bed are computed from the model and the results are compared with those of experiments. The effects of the adsorption time and reflux ratio on the product purity and the recovery are identified through numerical simulations. The optimization problem is formulated based on nonlinear equations obtained from simulations. The optimal operating conditions identified are applied to experiments. The results show higher recovery of CO₂ under optimal operating conditions.     

Influence of operating temperature on CO<Subscript>2</Subscript>-NH<Subscript>3</Subscript> reaction in an aqueous solution

Although aqueous ammonia solution has been focused on the removal of CO₂ from flue gas, there have been very few reports regarding the underlying analysis of the reaction between CO₂ and NH₃. In this work, we explored the reaction of CO₂-NH₃-H₂O system at various operating temperatures: 40 °C, 20 °C, and 5 °C. The CO₂ removal efficiency and the loss of ammonia were influenced by the operating temperatures. Also, infrared spectroscopy measurement was used in order to understand the formation mechanism of ion species in absorbent, such as NH₂COO⁻, HCO₃⁻, CO₃²⁻, and NH₄⁺, during CO₂, NH₃, and H₂O reaction. The reactions of CO₂-NH₃-H₂O system at 20 °C and 40 °C have similar reaction routes. However, a different reaction route was observed at 5 °C compared to the other operating temperatures, showing the solid products of ammonium bicarbonates, relatively. The CO₂ removal efficiency and the formation of carbamate and bicarbonate were strongly influenced by the operating temperatures. In particular, the analysis of the formation carbamate and bicarbonate by infrared spectroscopy measurement provides useful information on the reaction mechanism of CO₂ in an aqueous ammonia solution.     

Modelling of multicomponent gas separation with asymmetric hollow fibre membranes—methane enrichment from biogas

A mathematical model for the dynamic performance of gas separation with high flux, asymmetric hollow fibre membranes was developed considering the permeate pressure build‐up inside the fibre bore and cross flow pattern with respect to the membrane skin. The solution technique provides reliable examination of pressure and concentration profiles along the permeator length (both residue/permeate streams) with minimal effort. The proposed simulation model and scheme were validated with experimental data of gas separation from literature. The model and solution technique were applied to investigate dynamic performance of several membrane module configurations for methane recovery from biogas (landfill gas or digester gas), considering biogas as a mixture of CO₂, N₂ and CH₄. Recycle ratio plays a crucial role, and optimum recycle ratio vital for the retentate recycle to permeate and permeate recycle to feed operation was found. From the concept of two recycle operations, complexities involved in the design and operation of continuous membrane column were simplified. Membrane permselectivity required for a targeted separation to produce pipeline quality natural gas by methane‐selective or nitrogen‐selective membranes was calculated. © 2012 Canadian Society for Chemical Engineering     

Reactivity of a CaSO<Subscript>4</Subscript>-oxygen carrier in chemical-looping combustion of methane in a fixed bed reactor

Chemical-looping combustion (CLC) is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO₂. A reactivity study of CaSO₄ oxygen carrier in CLC of methane was conducted in a laboratory scale fixed bed reactor. The oxygen carrier particles were exposed in six cycles of alternating reduction methane and oxidation air. A majority of CH₄ reacted with CaSO₄ to form CO₂ and H₂O. The oxidation was incomplete, possibly due to the CaSO₄ product layer. The reactivity of CaSO₄ oxygen carrier increased for the initial cycles but slightly decreased after four cycles. The product gas yields of CO₂, CH₄, and CO with cycles were analyzed. Carbon deposition during the reduction period was confirmed with the combustible gas (CO+H₂) in the product gas and slight CO₂ formed during the early stage of oxidation. The mechanism of carbon deposition and effect was also discussed. SO₂ release behavior during reduction and oxidation was investigated, and the possible formation mechanism and mitigation method was discussed. The oxygen carrier conversion after the reduction decreased gradually in the cyclic test while it could not restore its oxygen capacity after the oxidation. The mass-based reaction rates during the reduction and oxidation also demonstrated the variation of reactivity of CaSO₄ oxygen carrier. XRD analysis illustrated the phase change of CaSO₄ oxygen carrier. CaS was the main reduction product, while a slight amount of CaO also formed in the cyclic test. ESEM analysis demonstrated the surface change of particles during the cyclic test. The reacted particles tested in the fixed bed reactor were not uniform in porosity. EDS analysis demonstrated the transfer of oxygen from CaSO₄ to fuel gas while leaving CaS as the dominant reduced product. The results show that CaSO₄ oxygen carrier may be an interesting candidate for oxygen carrier in CLC. This work was presented at the 7 ^th China-Korea Workshop on Clean Energy Technology held at Taiyuan, China, June 26–28, 2008.     

Adsorption characteristics analysis of CO<Subscript>2</Subscript> and N<Subscript>2</Subscript> in 13X zeolites by molecular simulation and N<Subscript>2</Subscript> adsorption experiment

The adsorption characteristics of CO₂ and N₂ in 13X zeolites have been studied by the molecular simulation and N₂ adsorption experiment. It is found that the simulation results by Dreiding force fields are in an agreement with the published data. The influence of the σ and ε parameters of O_Z and Na⁺ on the adsorption performance is discussed. Then the optimized force field parameters are obtained. Specific surface area (S _B ) is calculated by simulation and experiment. Its relative error is just only 4.3 %. Therefore, it is feasible that S _B of 13X zeolites is obtained by the simulation methods. Finally, the impacts of pressure and temperature on adsorption characteristics are investigated. At low pressure, CO₂ adsorption in 13X zeolites belongs to the surface adsorption. As the pressure increase, the partial multilayer adsorption appears along with the surface adsorption. N₂ adsorption in 13X zeolites is different from that of CO₂. At low temperature of 77 K, two primary peaks are caused by the surface adsorption and multilayer adsorption respectively regardless of pressure variation. When the temperature is 273 K, the energy distribution curve appears undulate at low pressures. Then it becomes stable with the pressure increase. The surface adsorption plays an important role at the relative high pressures. The results will help to provide the theory guide for the optimization of force field parameters of adsorbents, and it is very important significance to understand the adsorption performance of zeolites.