Characterization of Supported NiSO4 and Effect of TiO2–ZrO2 Composition on Catalytic Activity for Acid Catalysis

A series of catalysts, NiSO₄/TiO₂–ZrO₂ having different TiO₂–ZrO₂ composition, for acid catalysis was prepared by the impregnation method using an aqueous solution of nickel sulfate. The addition of TiO₂ to ZrO₂ improved the surface area of the catalyst and enhanced its acidity remarkably because of the formation of new acid sites through the charge imbalance of Ti–O–Zr bonding. The binary oxide, TiO₂–ZrO₂ calcined above 600 °C resulted in the formation of crystalline orthorhombic phase of ZrTiO₄. Therefore, NiSO₄/TiO₂–ZrO₂ calcined at 500 °C exhibited a maximum catalytic activity for acid catalysis, and then the catalytic activity decreased with the calcination temperature. The correlation between catalytic activity and acidity held for both reaction, 2-propanol dehydration and cumene dealkylation. NiSO₄ supported on 50TiO₂–50ZrO₂ (TiO₂/ZrO₂ ratio = 1) among TiO₂–ZrO₂ binary oxides exhibited the highest catalytic activity for acid catalysis.     

The Effects of Al2O3 Addition and WO3 Modification on Catalytic Activities of NiO/TiO2 for Acid Catalysis

NiO/Al₂O₃–TiO₂/WO₃ catalysts for acid catalysis were prepared by the addition of Al₂O₃ and the modification with WO₃. The strong acid sites were formed through the bonding between dispersed WO₃ and TiO₂. The larger the dispersed WO₃ amount, the higher both the acidity and catalytic activity. The addition of Al₂O₃ up to 5 mol% enhanced acidity and catalytic activity of NiO/Al₂O₃–TiO₂/WO₃ gradually due to the interaction between Al₂O₃ and TiO₂ and consequent formation of Al–O–Ti bond. The presence of NiO may attract reactants and enhance the local concentration of reactants near acid sites and consequently increase catalytic activity.     

Catalytic Properties of Cr2O3 Doped with MgO Supported on MgF2 and Al2O3

Catalytic properties of Cr₂O₃ supported on MgF₂ or Al₂O₃ have been modified by magnesium oxide. The catalysts have been obtained by the co-impregnation method and characterised by: BET, XRD and TPR. As follows from the results, the oxides supported on magnesium fluorine react with each other already at 400 °C, leading to formation of an amorphous spinel-like phase. On the Al₂O₃ support such an MgCr₂O₄ spinel has appeared at much higher temperatures. The addition of magnesium oxide has a significant effect on the activity and selectivity of the catalysts studied in the CO oxidation reaction at room temperature and in the reaction of cyclohexane dehydrogenation. The magnesium–chromium catalysts supported on MgF₂ have been found to show much higher activity and selectivity than the analogous systems supported on Al₂O₃.     

Novel Sn–Ce/Al2O3 Catalyst for the Selective Catalytic Reduction of NOx Under Lean Conditions

Effect of additives, Ce and Mn, on the catalytic performance of Sn/Al₂O₃ catalyst prepared by sol–gel method for the selective reduction of NO_x with propene under lean conditions was studied. Sn–Ce/Al₂O₃ catalysts exhibited higher activity than Sn/Al₂O₃ catalyst and the optimum Ce loading is 0.5–1%. The promoting effect of Ce is to enhance the oxidation of NO to NO₂ and facilitate the activation of propene, both of which are important steps for the NO_x reduction. The presence of oxygen contributes to the oxidation of NO and shows a promoting effect.     

Influence of Al2O3 support on the activity of Ag/Al2O3 catalysts for SCR of NO with decane

The role of the Al₂O₃ support on the activity of supported Ag catalyst towards the selective catalytic reduction (SCR) of NO with decane is elucidated. A series of Ag/Al₂O₃ catalysts were prepared by impregnation method and characterized by N₂ pore size distribution, XRD, UV–Vis, in-situ FT-IR and acidity measurement by NH₃ and pyridine adsorption. The catalytic activity differences of Ag/Al₂O₃ are correlated with different properties of Al₂O₃ supports and the active Ag species formed. 4wt% Ag supported on sol-gel prepared Al₂O₃ (Ag/Al₂O₃ (SG), showed higher NO _x conversion (65% at 400 °C), compared with the respective catalysts made from commercial Al₂O₃ (Ag/Al₂O₃ (GB), Ag/Al₂O₃ (ALO), (∼26 and 7% at 400 °C). The higher surface area, acidity and pore size distribution in sol–gel prepared Al₂O₃ (SG) results in higher NO and hydrocarbon conversion. Based on the UV–vis characterization, the activity of NO reduction is correlated to the presence of Ag_n^δ+ clusters and acidity of Al₂O₃ support was found to be one of the important parameter in promoting the formation and stabilization of Ag_n^δ+ clusters. Furthermore from pyridine adsorption results, presence of more number of Bronsted acid sites in Ag/Al₂O₃ (SG) is confirmed, which could also contribute to low temperature hydrocarbon activation and improve NO conversion. In situ FT-IR measurements revealed the higher rate of –CN and –NCO intermediate species formation over 4wt% Ag/Al₂O₃ (SG). We conclude that the physico–chemical properties of Al₂O₃ play a crucial role in NO _x conversion over Ag/Al₂O₃ catalysts. Thus, the activity of the Ag/Al₂O₃ catalyst can be tailored by using a proper type of Al₂O₃ support.     

Preparation and characterisation of closed-pore Al2O3-MgAl2O4 refractory aggregate utilising superplasticity

ABSTRACT

A novel high closed porosity Al₂O₃-MgAl₂O₄ refractory aggregate has been successfully fabricated by utilising superplasticity with Al₂O₃ and MgO as raw materials, SiC as high temperature pore-forming agent. The effects of the addition amounts of MgO and SiC on porosity, sintering behaviours, phase composition, pore size distribution and microstructure of the refractory aggregate have been investigated. The formation mechanism of the closed pore in the refractory aggregate has been discussed. The results showed that the MgO can improve the superplastic deformation ability of Al₂O₃-based ceramic at high temperature. With the content of MgO and SiC increased, the closed porosity and the pore size increased. The oxidation of SiC improved the sinterability of materials at the initial stage of sintering, and then the released gases due to the further oxidation of SiC promoted the formation of closed pores by motivating the superplastic deformation ability of Al₂O₃-based materials.     

A Novel Catalyst Pt/CoAl2O4/Al2O3 for Combination CO2 Reforming and Partial Oxidation of CH4

Pt/CoAl₂O₄/Al₂O₃, Pt/CoO_x/Al₂O₃, CoAl₂O₄/Al₂O₃ and CoO_x/Al₂O₃ catalysts were studied for combination CO₂ reforming and partial oxidation of CH₄. The results indicate that Pt/CoAl₂O₄/Al₂O₃ is the most effective, and XRD results indicate that Pt species are well dispersed over the Pt/CoAl₂O₄/Al₂O₃. High dispersion is related to the presence of CoAl₂O₄, formed during calcining at high temperature before Pt addition. In the presence of Pt, CoAl₂O₄ in the catalyst could be reduced partially at 973 K. Based on these results, it appears that zerovalent platinum with high dispersion and zerovalent cobalt resulting from CoAl₂O₄ reduction are responsible for high activity in the Pt/CoAl₂O₄/Al₂O₃ catalyst.     

Effect of Pt Incorporation into Ni/ZrO2–SO 4 = /Al2O3 Catalyst for n-Butane Isomerization

Three Ni/ZrO₂–SO₄⁼/Al₂O₃ catalysts with different concentrations of platinum (0.2, 0.3 and 0.4 wt%) were prepare and tested for n-butane isomerization reaction at 338 K, in absence and in presence of hydrogen. The results shown that, at low temperature, platinum contributes to the olefin or butyl ion formation and the reaction follows a bimolecular pathway. However, when the reaction occurs in the presence of hydrogen, the formation of butyl ions is inhibited. The main feature of platinum addition is the stabilization of the catalytic activity, which is indicated by the slow deactivation constants compared to that of the unpromoted catalyst.     

Effect of Modifiers on the Reactivity of Cr2O3/Al2O3 and Cr2O3/TiO2 Catalysts for the Oxidative Dehydrogenation of Propane

Chromium oxide supported on alumina and titania supports was modified with oxides of sodium, vanadium and molybdenum. The modified and unmodified chromium oxide catalysts were characterized by several techniques. The presence of surface chromium oxide and surface molybdenum and vanadium oxide species was detected in the unmodified and molybdenum and vanadium oxide modified supported chromium oxide catalysts. The reducibility (T_max and H/Cr ratio) of the surface chromium species was not affected for the vanadium and molybdenum oxide modified catalysts; however, the reducibility changed noticeably for sodium modified supported chromium oxide catalysts. Studies of the reactivity of the ODH of propane revealed the effect of modifiers on the reactivity properties of the surface chromium oxide species. The activity and propene selectivity decreased for sodium modified supported chromium oxide catalysts. However, the activity increased for vanadium oxide modified catalysts and was similar for molybdenum oxide modified catalysts irrespective of the support. The propene selectivity was higher for molybdenum oxide modified chromium oxide catalysts. However, the propene selectivity for vanadium oxide modified catalysts depends on the support since it appears that the inherent selectivity of the surface vanadium oxide species is reflected.     

Water Denitration over a Pd–Sn/Al2O3 Catalyst

Bimetallic Pd–Sn catalysts were synthesized by incipient-wetness impregnation of the metals on alumina and employed for the reduction of nitrates from aqueous solutions. The catalysts were characterized by FTIR spectroscopy of adsorbed CO, X-ray diffraction (XRD), transmission electron microscopy (TEM), and H₂ chemisorption. The influence of the metal ratio was evaluated in reaction measurements. The bimetallic Pd–Sn catalysts exhibited high selectivity for nitrate removal forming less NO₂⁻ and NH₄⁺ than the Pd–Cu catalysts.     

The reduction behavior of Mo/TiO2-Al2O3 catalyst

The effect of TiO₂ modified Al₂O₃ surface on the reducibility of MoO₃ has been studied by TPR and XPS. The results show that Mo⁶⁺ in Mo/TiO₂-Al₂O₃ can be reduced to much lower valency, especially at low Mo loading. The influence of the calcination temperature on the reduction of Mo⁶⁺ on Al₂O₃ and TiO₂-Al₂O₃ carriers is different. The data reveals that the reducibility of Mo⁶⁺ on Al₂O₃ slightly decreased, while that on TiO₂-Al₂O₃ increased when the calcination temperature was raised. It is suggested that the stronger tetrahedral site of the Al₂O₃ surface was first occupied by TiO₂ and main octahedral Mo⁶⁺ in polymeric species-; and a small crystalline MoO₃ formed on TiO₂-Al₂O₃, whereas the formation of tetrahedral Mo⁶⁺ species and Al₂(MoO₄)₃ phase was inhibited.     

Surface acidity investigation of A12O3 supports and Ni-Mo/Al2O3 catalysts using the temperature-programmed desorption oftert-butylamine

The relative acid site densities of a range of Ni-Mo/Al₂O₃ based catalysts were measured by the temperature-programmed desorption of tert-butylamine. The catalysts investigated possessed different surface areas and active species loadings. The effect of active species impregnation on the acidity of blank aluminas was also determined. Similarly the effect of sulphiding on catalyst acidity was also addressed.     

Low temperature selective catalytic reduction of NO by NH3 over V2O5 supported on TiO2–SiO2–MoO3

The V₂O₅ catalysts supported on TiO₂–SiO₂–MoO₃ (TSM) prepared by the coprecipitation method were investigated for the selective catalytic reduction (SCR) of NO by NH₃ at low temperatures. The V₂O₅/TSM catalyst with 7–13 wt% SiO₂ was found to exhibit a superior SCR activity and a good sulfur tolerance at low temperatures (<250 °C). The presence of highly active polymeric vanadates formed by the incorporation of MoO₃ to TiO₂–SiO₂ and superior redox properties seems to enhance SCR activity, and furthermore the very lower SO₂ oxidation activity due to the higher acidity leads to the remarkable improvement of sulfur tolerance.     

Metal oxide catalysts for DME steam reforming: Ga2O3 and Ga2O3–Al2O3 catalysts

The steam reforming of dimethyl ether (DME) was performed on Ga₂O₃–Al₂O₃ mixed oxides prepared by sol–gel method. Ga₂O₃ significantly affects the catalytic performance with respect to the DME conversion and H₂ yield. The catalytic activity increases with the Ga concentration in Ga₂O₃–Al₂O₃ mixed oxides. It is very interesting that without the aid of an additional transition metal component, Ga₂O₃ and Ga₂O₃ containing Al₂O₃ mixed oxide system exhibit good activity in the reforming reaction. To the best of our knowledge, this is the first report that reveals the reforming ability of Ga₂O₃ for the production of H₂ from DME and/or methanol.     

Gadolinium oxide nanocrystal nonvolatile memory with HfO2/Al2O3 nanostructure tunneling layers

In this study, Gd₂O₃ nanocrystal (Gd₂O₃-NC) memories with nanostructure tunneling layers are fabricated to examine their performance. A higher programming speed for Gd₂O₃-NC memories with nanostructure tunneling layers is obtained when compared with that of memories using a single tunneling layer. A longer data retention (< 15% charge loss after 10⁴ s) is also observed. This is due to the increased physical thickness of the nanostructure tunneling layer. The activation energy of charge loss at different temperatures is estimated. The higher activation energy value (0.13 to 0.17 eV) observed at the initial charge loss stage is attributed to the thermionic emission mechanism, while the lower one (0.07 to 0.08 eV) observed at the later charge loss stage is attributed to the direct tunneling mechanism. Gd₂O₃-NC memories with nanostructure tunneling layers can be operated without degradation over several operation cycles. Such NC structures could potentially be used in future nonvolatile memory applications.     

Pulse studies of CH4 interaction with NiO/Al2O3 catalysts

Pulse studies of the interaction of CH₄ and NiO/Al₂O₃ catalysts at 500°C indicate that CH₄ adsorption on reduced nickel sites is a key step for CH₄ oxidative conversion. On an oxygen-rich surface, CH₄ conversion is low and the selectivity of CO₂ is higher than that of CO. With the consumption of surface oxygen, CO selectivity increases while the CO₂ selectivity falls. The conversion of CH₄ is small at 500°C when a pulse of CH₄/O₂ (CH₄O₂=21) is introduced to the partially reduced catalyst, indicating that CH₄ and O₂ adsorption are competitive steps and the adsorption of O₂ is more favorable than CH₄ adsorption     

In situ synthesis,mechanical and cyclic oxidation properties of Ti3AlC2/Al2O3 composites

ABSTRACT

Ti₃AlC₂/Al₂O₃ composite materials were successfully fabricated from TiO₂/TiC/Ti/Al powders by the in situ reactive hot pressed technique. The microstructure, mechanical and oxidation properties of the composites were investigated in the paper. Vickers hardness increased with the Al₂O₃ content. The relative density of Ti₃AlC₂/Al₂O₃ composites exhibits a declining tendency with Al₂O₃ content especially exceeds 10 vol.?%. The Ti₃AlC₂/Al₂O₃ composites show excellent electrical conductivity. The flexural strength and fracture toughness of Ti₃AlC₂/10 vol. % Al₂O₃ are 461 ± 20?MPa and 6.2?±?0.2?MPa m^1/2, respectively. The cyclic oxidation behaviour of resistance of Ti₃AlC₂/10 vol. % Al₂O₃ composites at 800–1000°C generally obeys a parabolic law. The oxide scale of sample consists of a mass of α-Al₂O₃ and TiO₂, forming a dense and adhesive protect layer. The result indicates that the Al₂O₃ can greatly improve the oxidation resistance of Ti₃AlC₂.     

Investigation of the sulfidation of Mo/TiO2-Al2O3 catalysts by TPS and LRS

A series of Mo/Al₂O₃ and Mo/TiO₂-Al₂O₃ catalysts were investigated by temperature programmed sulfiding (TPS) and laser Raman spectroscopy (LRS). The effect of TiO₂ on the sulfidability of molybdena was studied in detail. It is found that Mo/Al₂O₃ catalysts can be partially sulfided by O-S exchange at low temperature, forming molybdenum oxysulfide. The Mo-S bond subsequently ruptures in the presence of H₂ to produce H₂S. At 530–550 K deep sulfiding of molybdenum oxysulfide occurs forming crystalline MoS₂. When the surface of Al₂O₃ was covered by a monolayer of TiO₂, the sulfiding rate of molybdena at low temperature was not only greatly increased, but H₂S produced in the reduction of Mo-S species caused deep sulfiding of the catalyst which resulted in a decrease of the TPS peak temperature by 80–100 K. The results indicate that this promotion of the sulfiding of molybdena is enhanced with TiO₂ loading. The function of TiO₂ is explained by the weakened interaction between MoO₃ and Al₂O₃ due to the coverage of the Al₂O₃ surface by TiO₂.     

Activity and stability of Cu/ZnO/Al2O3 catalyst promoted with B2O3 for methanol synthesis

The addition of B₂O₃ to a Cu/ZnO/Al₂O₃ catalyst increased the activity of the catalyst for methanol synthesis after an induction period during the reaction. The stability of the B₂O₃-containing Cu/ZnO/Al₂O₃ catalyst was greatly improved by the addition of a small amount of colloidal silica to the catalyst. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation and characterization of SO42-/TiO2 and S2O82-/TiO2 catalysts

Nanosized solid superacids SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂, as well as MCM-41-supported SO₄ ²⁻/ZrO₂, were prepared. Their structures, acidities, and catalytic activities were investigated and compared using XRD, N₂ adsorption-desorption, and in situ FTIR-pyridine adsorption, as well as an evaluation reaction with pseudoionone cyclization. The results showed that SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ possess not only nanosized particles with diameters < 7.0 nm, a BET surface greater than 140 cm²/g and relatively regular mesostructures with pores around 4.0 nm, but also a pure anatase phase and strong acidity. Different from the Lewis acid nature of SO₄ ²⁻/ZrO₂/MCM-41, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibit mainly Bronsted acidities. The strongest Bronsted acid sites were produced on SO₄ ²⁻/TiO₂ promoted with H₂SO₄, while Lewis acid sites on S₂O₈ ²⁻/TiO₂ even stronger than those on SO₄ ²⁻/ZrO₂/MCM-41 were generated when persulfate solution was used as sulfating agent. Because of their distinct acid natures, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibited catalytic activities for the cyclization of pseudoionone that were much higher than that of SO₄ ²⁻/ZrO₂/MCM-41. It can be concluded that the existence of more Br?nsted acid sites was favorable for proton participation in the cyclization reaction. Translated from Journal of Chemical Engineering of Chinese Universities, 2006, 20(2): 239–244 [译自: 高校化学工程学报]