Microwave Dielectric Properties and Low-Temperature Sintering of Ba0.60Sr0.40TiO3 Ceramics

In the present work, the sintering behaviors and dielectric properties of Ba_0.60Sr_0.40TiO₃ (BST) ceramics with the addition of BaCu(B₂O₅) were investigated in detail. The results indicated that the addition reduced the sintering temperature of BST by about 500°C. It was suggested that a liquid phase BaCu(B₂O₅) assisted the densification of BST ceramics at lower temperatures. For a low-level BaCu(B₂O₅) addition (2.0 mol%), the BST sample sintered at 950°C for 5 h displayed good dielectric properties, with a moderate dielectric constant (ɛ=2553) and a low dielectric loss (tan δ=0.00305) at room temperature and at 10 kHz. The sample showed 45.9% tunability at 10 kHz under a dc electric field of 30 kV/cm. At the frequency of 0.984 GHz, BST-added 2.0 mol% BaCu(B₂O₅) possessed a dielectric constant of 2204 and a Q value of 146.7.     

Microwave Dielectric Properties of Li2TiO3 Ceramics Doped with ZnO–B2O3 Frit

A type of new low sintering temperature ceramic, Li₂TiO₃ ceramic, has been found. Although it is difficult for the Li₂TiO₃ compound to be sintered compactly at temperatures above 1000°C for the volatilization of Li₂O, dense Li₂TiO₃ ceramics were obtained by conventional solid-state reaction method at the sintering temperature of 900°C with the addition of ZnO–B₂O₃ frit. The sintering behavior and microwave dielectric properties of Li₂TiO₃ ceramics with less ZnO–B₂O₃ frit (≤3.0 wt%) doping were investigated. The addition of ZnO–B₂O₃ frit can lower the sintering temperature of the Li₂TiO₃ ceramics, but it does not apparently degrade the microwave dielectric properties of the Li₂TiO₃ ceramics. Typically, the good microwave dielectric properties of ɛ_r=23.06, Q × f =32 275 GHz, τ_f = 35.79 ppm/°C were obtained for 2.5 wt% ZnO–B₂O₃ frit-doped Li₂TiO₃ ceramics sintered at 900°C for 2 h. The porosity was 0.08%. The Li₂TiO₃ ceramic system may be a promising candidate for low-temperature cofired ceramics applications.     

Synthesis of BaCu(B2O5) Ceramics and their Effect on the Sintering Temperature and Microwave Dielectric Properties of Ba(Zn1/3Nb2/3)O3 Ceramics

BaCu(B₂O₅) ceramics were synthesized and their microwave dielectric properties were investigated. BaCu(B₂O₅) phase was formed at 700°C and melted above 850°C. The BaCu(B₂O₅) ceramic sintered at 810°C had a dielectric constant (ɛ_r) of 7.4, a quality factor ( Q × f ) of 50 000 GHz and a temperature coefficient of resonance frequency (τ_f) of −32 ppm/°C. As the BaCu(B₂O₅) ceramic had a low melting temperature and good microwave dielectric properties, it can be used as a low-temperature sintering aid for microwave dielectric materials for low temperature co-fired ceramic application. When BaCu(B₂O₅) was added to the Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramic, BZN ceramics were well sintered even at 850°C. BaCu(B₂O₅) existed as a liquid phase during the sintering and assisted the densification of the BZN ceramic. Good microwave dielectric properties of Q × f =16 000 GHz, ɛ_r=35, and τ_f=22.1 ppm/°C were obtained for the BZN+6.0 mol% BaCu(B₂O₅) ceramic sintered at 875°C for 2 h.     

Sintering and Microwave Dielectric Properties of the LiNb0.63Ti0.4625O3 Ceramics with the B2O3–SiO2 Liquid-Phase Additives

The effect of B₂O₃–SiO₂ liquid-phase additives on the sintering, microstructure, and microwave dielectric properties of LiNb_0.63Ti_0.4625O₃ ceramics was investigated. It was found that the sintering temperature could be lowered easily, and the densification and dielectric properties of LiNb_0.63Ti_0.4625O₃ ceramics could be greatly improved by adding a small amount of B₂O₃–SiO₂ solution additives. No secondary phase was observed for the ceramics with B₂O₃–SiO₂ additives. With the addition of 0.10 wt% B₂O₃–SiO₂, the ceramics sintered at 900°C showed favorable microwave dielectric properties with ɛ_r=71.7, Q × f =4950 GHz, and τ_f=−2.1 ppm/°C. The energy dispersive spectra analysis showed an excellent co-firing interfacial behavior between the LiNb_0.63Ti_0.4625O₃ ceramic and the Ag electrode. It indicated that LiNb_0.63Ti_0.4625O₃ ceramics with B₂O₃–SiO₂ solution additives have a number of potential applications on passive integrated devices based on the low-temperature co-fired ceramics technology.     

Effect of Glass Additions on BaO–TiO2–WO3 Microwave Ceramics

The effect of glass addition on the properties of BaO–TiO₂-WO₃ microwave dielectric material N-35, which has Q = 5900 and K = 35 at 7.2 GHz for samples sintered at 1360°C, was investigated. Several glasses including B₂O₃, SiO₂, 5ZnO–2B₂O₃, and nine other commercial glasses were selected for this study. Among these glasses, one with a 5 wt% addition of B₂O₃ to N-35, when sintered at 1200°C, had the best dielectric properties: Q = 8300 and K = 34 at 8.5 GHz. Both Q and K increased with firing temperature as well as with density. The Q of N-35, when sintered with a ZnO–B₂O₃ glass system, showed a sudden drop in the sintering temperature to about 1000°C. The results of XRD, thermal analysis, and scanning electron microscopy indicated that the chemical reaction between the dielectric ceramics and glass had a greater effect on Q than on the density. The effects of the glass content and the mixing process on the densification and microwave dielectric properties are also presented. Ball milling improved the densification and dielectric properties of the N-35 sintered with ZnO–B₂O₃.     

Effects of B2O3 on the Phase Stability of Ba2Ti9O20 Microwave Ceramic

Preparation of dense and phase-pure Ba₂Ti₉O₂₀ is generally difficult using solid-state reaction, since there are several thermodynamically stable compounds in the vicinity of the desired composition and a curvature of Ba₂Ti₉O₂₀ equilibrium phase boundary in the BaO–TiO₂ system at high temperatures. In this study, the effects of B₂O₃ on the densification, microstructural evolution, and phase stability of Ba₂Ti₉O₂₀ were investigated. It was found that the densification of Ba₂Ti₉O₂₀ sintered with B₂O₃ was promoted by the transient liquid phase formed at 840°C. At sintering temperatures higher than 1100°C, the solid-state sintering became dominant because of the evaporation of B₂O₃. With the addition of 5 wt% B₂O₃, the ceramic yielded a pure Ba₂Ti₉O₂₀ phase at sintering temperatures as low as 900°C, without any solid solution additive such as SnO₂ or ZrO₂. The facilities of B₂O₃ addition to the stability of Ba₂Ti₉O₂₀ are apparently due to the eutectic liquid phase which accelerates the migration of reactant species.     

Low-Temperature Sintering and Microwave Dielectric Properties of the Zn2SiO4 Ceramics

B₂O₃ was added to nominal composition Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature for application to low-temperature cofired ceramic (LTCC) devices. B₂O₃ reacted with SiO₂ to form a liquid phase containing SiO₂ and B₂O₃. The composition and melting temperature of the liquid phase depended on the sintering temperature and the B₂O₃ content. The specimen containing 20.0 mol% of B₂O₃ sintered at 900°C exhibited high microwave dielectric properties of Q × f =53 000 GHz, ɛ _r=5.7, and τ_f=−16 ppm/°C, confirming the promising potential of the B₂O₃-added ZS ceramics as candidate materials for the LTCC devices.     

Microwave Dielectric Properties of 5Li2O–0.583Nb2O5–3.248TiO2 Ceramics with V2O5

The effects of V₂O₅ addition on the sintering behavior, microstructure, and the microwave dielectric properties of 5Li₂O–0.583Nb₂O₅–3.248TiO₂ (LNT) ceramics have been investigated. With addition of low-level doping of V₂O₅ (≤2 wt%), the sintering temperature of the LNT ceramics could be lowered down to around 920°C due to the liquid phase effect. A secondary phase was observed at the level of 2 wt% V₂O₅ addition. The addition of V₂O₅ does not induce much degradation in the microwave dielectric properties but lowers the τ_f value to near zero. Typically, the excellent microwave dielectric properties of ɛ_r=21.5, Q × f =32 938 GHz, and τ_f=6.1 ppm/°C could be obtained for the 1 wt% V₂O₅-doped sample sintered at 920°C, which is promising for application of the multilayer microwave devices using Ag as an internal electrode.     

Effects of Heating Rate on the Sintering Behavior and the Dielectric Properties of Ba0.7Sr0.3TiO3 Ceramics Prepared by Boron-Containing Liquid-Phase Sintering

The effects of heating rate on the sintering behavior and the dielectric properties of Ba_0.7Sr_0.3TiO₃ ceramics prepared by boron-containing liquid-phase sintering were investigated. When 0.5 wt% B₂O₃ was added to Ba_0.7Sr_0.3TiO₃, sintering was achieved at ∼1150°C, and the overdoped B₂O₃ did not form an adequate amount of liquid phase or volatilize; it remained in the samples and formed a secondary phase. A transition broadening was observed as the heating rate increased. As the heating rate increased, the Curie temperature increased and the maximum dielectric constant ( k _max) at the Curie temperature decreased. This result is attributable to a decrease in the diffuseness parameter (δ) and the tetragonality ( c / a ).     

Influence of V2O5 Additions to 5Li2O–1Nb2O5–5TiO2 Ceramics on Sintering Temperature and Microwave Dielectric Properties

The effects of the addition of V₂O₅ on the sintering behavior, microstructure, and microwave dielectric properties of 5Li₂O–1Nb₂O₅–5TiO₂ (LNT) ceramics have been investigated. With low-level doping of V₂O₅ (≤3 wt%), the microstructure of the LNT ceramic changed from a special two-level intergrowth structure into a two-phase composite structure with separate grains. And the sintering temperature of the LNT ceramics could be lowered to around 900°C by adding a small amount of V₂O₅ without much degradation in microwave dielectric properties. Typically, better microwave dielectric properties of ɛ_r=41.7, Q × f =7820 GHz, and τ _f =45 ppm/°C could be obtained for the 1 wt% V₂O₅-doped ceramics sintered at 900°C.     

Low-Temperature Firing and Microwave Dielectric Properties of Ca[(Li1/3Nb2/3)0.84Ti0.16]O3−δ Ceramics for LTCC Applications

The effects of LiF and ZnO–B₂O₃–SiO₂ (ZBS) glass combined additives on phase composition, microstructures, and microwave dielectric properties of Ca[(Li_1/3Nb_2/3)_0.84Ti_0.16]O_3−δ (CLNT) ceramics were investigated. The LiF and ZBS glass combined additives lowered the sintering temperature of CLNT ceramics effectively from 1150° to 880°C. The main diffraction peaks of all the specimens split due to the coexistence of the non-stoichiometric phase (A) and stoichiometric phase (B), which all possess CaTiO₃-type perovskite structures. The transformation from A into B became accelerated with the increase of LiF or ZBS content. ZBS glass restrained the volatilization of lithium salt, which greatly affected the microstructures and microwave dielectric properties. CLNT ceramics with 2 wt% LiF and 3 wt% ZBS sintered at 900°C for 2 h show excellent dielectric properties: ɛ_r=34.3, Q × f =17 400 GHz, and τ_f=−4.6 ppm/°C. It is compatible with Ag electrodes, which makes it a promising ceramic for low-temperature cofired ceramics technology application.     

Microwave Dielectric Properties of Low-Fired Ba5Nb4O15

The effect of B₂O₃ on the sintering temperature and microwave dielectric properties of Ba₅Nb₄O₁₅ has been investigated using X-ray powder diffraction, scanning electron microscopy, and a network analyzer. Interactions between Ba₅Nb₄O₁₅ and B₂O₃ led to formation of second phases, BaNb₂O₆ and BaB₂O₄. The addition of B₂O₃ to Ba₅Nb₄O₁₅ resulted in lowering the sintering temperature from 1400° to 925°C. Low-fired Ba₅Nb₄O₁₅ could be interpreted by measuring changes in the quality factor ( Q × f ), the relative dielectric constant (ɛ_r), and the temperature coefficient of resonant frequency (τ_f) as a function of B₂O₃ additions. More importantly, the formation of BaNb₂O₆ provided temperature compensation. The microwave dielectric properties of low-fired Ba₅Nb₄O₁₅ had good dielectric properties: Q × f = 18700 GHz, ɛ_r= 39, and τ_f= 0 ppm/°C.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Low-Temperature Sintering Barium Titanate-Based X8R Ceramics with Nd2O3 Dopant and ZnO–B2O3 Flux Agent

To demonstrate that barium titanate-based ceramics could be sintered at a low temperature thus reducing the cost of capacitor production, systematic investigation has been made on the structure and dielectric properties of barium titanate-based X8R ceramics, doped with various Nd₂O₃ content and different ZnO–B₂O₃ solution as the sintering aids. The dielectric ceramic powder with good permittivity and low dielectric loss were obtained at a sintering temperature of 900°C, meeting X8R specifications. Transmission electron microscopy and EDS analysis shows a high concentration of Nd element in the boundary regions, which verifies the beneficial role of Nd in facilitating the formation of core-shell structure. The results also suggest that the developed BaTiO₃-based ceramics may serve as a promising candidate for fabricating cheap multilayer capacitors with pure Ag as inner electrode.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Densification of Cr2O3-ZrO2 Ceramics by Sintering

Cr₂O₃ and ZrO₂ were mixed in various ratios and pressed to form compacts, which were then sintered in carbon powder. Compacts with >30 wt% Cr₂O₃ were sintered to densities >98% of true density at 1500°C. This method of sintering in carbon powder can be used to prepare very dense Cr₂O₃-ZrO₂ ceramics at a relatively low temperature, (∼1500°C) without additives.     

Effect of Excess PbO on the Sintering Characteristics and Dielectric Properties of Pb(Mg1/3Nb2/3)O3–PbTiO3-Based Ceramics

Additions of excess PbO to the perovskite Pb[(Mg_1/3Nb_2/3)_0.92Ti_0.08]O₃ solid solution enhanced the formation of a liquid phase at 840°C, which served as a densification aid for the ceramics. The liquid phase allowed elimination of pores and promoted grain growth during sintering. With additions of 1 to 2 wt% excess PbO, densities in excess of 97% of theoretical were obtained at a sintering temperature of 950°C. The peak dielectric constants of the resulting ceramics were over 18 000 at 30°C and dissipation factors less than 1%. Additions of PbO in excess of 2 wt% resulted in inferior dielectric properties due mainly to the dilution of the ferroelectric phase.     

Microwave Dielectric Properties and Chemical Resistance of Low-Temperature-Sintered CaZrB2O6 Ceramics

Dolomite-type borate ceramics consisting of CaZrB₂O₆ were synthesized via a conventional solid-state reaction route; low-temperature sintering was explored using Bi₂O₃–CuO additives of 1–7 wt% for low-temperature co-fired ceramics applications. For several sintering temperatures, the microwave dielectric properties and chemical resistance of the ceramics were investigated. The CaZrB₂O₆ ceramics with 3 wt% Bi₂O₃–CuO addition could be sintered below 925°C, and the microwave dielectric properties of the low-temperature samples were ɛ_r=10.55, Q × f =87,350 GHz, and τ_f=+2 ppm/°C. The chemical resistance test result showed that both CaZrB₂O₆- and Bi₂O₃–CuO-added CaZrB₂O₆ ceramics were durable in basic solution but were degraded in acid solution.     

Effect of Bismuth Borate/LiF on the Sintering, Thermal, and Microwave Dielectric Properties of Ba6−3xSm8+2xTi18O54 (x=2/3) Solid Solution

Ba_{6−3 x} Sm_{8+2 x} Ti₁₈O₅₄ ( x =2/3) (BST) was prepared by the solid-state method and the effect of bismuth borate (BB)/LiF on the sinterability, microstructure, and thermal and microwave dielectric properties were studied. BST+3.5 wt% BB+0.5 wt% LiF composite sintered at 1050°C has Q × f =4500 GHz, ɛ=52, and τ _f =+6 ppm/°C. Raman spectrum of the composite was compared with that of BST and the structural changes were investigated.     

Effects of La2O3/ZnO Additives on Microstructure And Microwave Dielectric Properties of Zr0.8Sn0.2TiO4 Ceramics

Dielectric ceramics of Zr_0.8Sn_0.2TiO₄ containing La₂O₃ and ZnO as sintering aids were prepared and investigated for microstructure and microwave dielectric properties. Low-level doping with La₂O₃ and ZnO (up to 0.30 wt%) is good for densification and dielectric properties. These additives do not affect the dielectric constant and the temperature coefficient. Dielectric losses increase significantly at additive levels higher than 0.15 wt%. The combined additives La₂O₃ and ZnO act as grain growth enhancers. With 0.15 wt% additives, a ceramic having a dielectric constant, a quality factor, and a temperature coefficient of frequency at 4.2 GHz of 37.6, 12 800, and –2.9 ppm/°C, respectively, was obtained. The quality factor was considerably improved by prolonged sintering.