Critical heat flux enhancement in pool boiling using alumina nanofluids

The pool boiling characteristics of dilute dispersions of alumina nanoparticles in water were studied. Consistent with other nanofluid studies, it was found that a significant enhancement in critical heat flux (CHF) can be achieved at modest nanoparticle concentrations (<0.1% by volume). During experimentation and subsequent inspection, formation of a porous layer of nanoparticles on the heater surface occurred during nucleate boiling. This layer significantly changes surface texture of the heater wire surface which could be the reason for improvement in the CHF value. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20301     

Surface effects of ribbon heaters on critical heat flux in nanofluid pool boiling

This paper deals with a study of enhanced critical heat flux (CHF) and burnout heat flux (BHF) in pool boiling of water with suspended silica nanoparticles using Nichrome wires and ribbons. Previously the current authors and other researchers have reported three-digit percentage increase in critical heat flux in silica nanofluids. This study investigates the effect of various heater surface dimensions, cross-sectional shapes as well as surface modifications on pool boiling heat transfer characteristics of water and water-based nanofluids. Our data suggest that the CHF and BHF decrease as heater surface area increases. For concentrations from 0.1 vol% to 2 vol%, the deposition of the particles on the wire allows high heat transfer through inter-agglomerate pores, resulting in a nearly 3-fold increase in burnout heat flux at very low concentrations. The nanoparticle deposition plays a major role through variation in porosity. The CHF enhancement is non-monotonic with respect to concentration. As the concentration is increased, the CHF and BHF decrease prior to increasing again at higher concentrations. Results show a maximum of 270% CHF enhancement for ribbon-type heaters. The surface morphology of the heater was investigated using SEM and EDS analyses, and it was inferred that the 2 vol% concentration deposition coating had higher porosity and rate of deposition compared with 0.2 vol% case.     

Surface wettability change during pool boiling of nanofluids and its effect on critical heat flux

The pool boiling characteristics of dilute dispersions of alumina, zirconia and silica nanoparticles in water were studied. Consistently with other nanofluid studies, it was found that a significant enhancement in critical heat flux (CHF) can be achieved at modest nanoparticle concentrations (<0.1% by volume). Buildup of a porous layer of nanoparticles on the heater surface occurred during nucleate boiling. This layer significantly improves the surface wettability, as shown by a reduction of the static contact angle on the nanofluid-boiled surfaces compared with the pure-water-boiled surfaces. A review of the prevalent CHF theories has established the nexus between CHF enhancement and surface wettability changes caused by nanoparticle deposition. This represents a first important step towards identification of a plausible mechanism for boiling CHF enhancement in nanofluids.     

A fractal model for critical heat flux in pool boiling

In this paper, a fractal model for the high heat flux nucleate boiling region and for the critical heat flux (CHF) is proposed. The expression for the critical heat flux (CHF) is derived based on the fractal distribution of nucleation sites on boiling surfaces. The proposed fractal model for CHF is found to be a function of wall superheat, the contact angle and physical properties of fluid. The relation between CHF and the number of active nucleation sites is obtained from the fractal distribution of active nucleation sites on boiling surfaces. The contact angle and the physical properties of fluid have the important effects on CHF. The predicted CHF from a boiling surface based on the proposed fractal model is compared with the existing experimental data. An excellent agreement between the proposed model predictions and experimental data is found.     

Visualization of a principle mechanism of critical heat flux in pool boiling

A new experimental work was made to discover a principle mechanism of the burnout in pool boiling. Here, we directly observed a liquid layer structure under a massive vapor clot and the liquid layer-related burnout phenomenon. Based on the present observations, we have made a visual model for the formation and dryout of a liquid film under its vapor environment. At the formation process, liquid is trapped in interleaved space between growing bubbles and surface and the liquid trapping continues between coalesced bubbles and surface. In the dryout process, we especially observed vapor “holes” made by spontaneous breakup of discrete nucleating bubbles inside a vapor clot. The burnout can be triggered by the evaporation of the liquid film region expanded from rims of the holes.     

Numerical prediction of critical heat flux in pool boiling with the two-fluid model

Three-dimensional numerical simulations of the atmospheric saturated pool boiling are performed with the aim of predicting the critical heat flux. The two-phase mixture in pool boiling is described with the transient two-fluid model. The transient heat conduction in the horizontal heated wall is also solved. Dynamics of vapor generation on the heated wall is modeled through the density of nucleation sites and the bubble residence time on the wall. The heater’s surface is divided into zones, which number per unit area equals the density of nucleation sites, while the location of nucleation site within each zone is determined by a random function. The results show a replenishment of the heater’s surface with water and surface wetting for lower heat fluxes, while heater’s surface dry-out is predicted at critical heat flux values. Also, it is shown that the decrease of nucleation site density leads to the reduction of critical heat flux values. Obtained results of critical heat flux are in good agreement with available measured data. The presented approach is original regarding both the application of the two-fluid two-phase model for the prediction of boiling crisis in pool boiling and the defined boundary conditions at the heated wall surface.     

Enhancement of pool boiling critical heat flux in dielectric liquids by microporous coatings

An experimental investigation into the effects of pressure and subcooling on the pool boiling critical heat flux from a bare silicon chip-like heater and from a silicon heater coated with microporous layers, is reported. The dual inline heater package was immersed in FC-72, a dielectric fluid, and the experiments were performed in the horizontal orientation, with subcooling varying between 0 K and 72 K, and the pressure between 101.3 kPa and 303.9 kPa. The maximum CHF values on the diamond-base microporous-coated silicon heater were found to reach 47 W/cm², at 3 atm and nearly 50 K of subcooling, and to provide an average enhancement of approximately 60% over the values attained with un-treated silicon surfaces. An available CHF correlation, with a reported standard deviation of 12.5% for un-treated surfaces over a large range of pressures, subcoolings, and surface conditions, was shown to predict the pressure and subcooling effects on CHF from the surface-enhanced chip with a standard deviation of 12%.     

Boiling behaviors and critical heat flux on a horizontal plate in saturated pool boiling of water at high pressures

Observations of boiling behaviors and measurements of critical heat flux (CHF) were carried out for saturated water boiling on a horizontal, upward-facing plate at pressures from atmospheric to 7 MPa. The primary bubbles diminish in size almost in inverse proportion to pressure and commence to coalesce in the very low heat flux region. The diameter of detached coalesced bubbles increases with increases in the heat flux and reaches about 10 mm even at a pressure of 5 MPa. Detachment frequency of the coalesced bubbles was unaffected by the heat flux and pressure. The CHF predicted based on the macrolayer dryout model agrees well with the measured data.     

Surface wettability effects on critical heat flux of boiling heat transfer using nanoparticle coatings

This study investigates the effects of surface wettability on pool boiling heat transfer. Nano-silica particle coatings were used to vary the wettability of the copper surface from superhydrophilic to superhydrophobic by modifying surface topography and chemistry. Experimental results show that critical heat flux (CHF) values are higher in the hydrophilic region. Conversely, CHF values are lower in the hydrophobic region. The experimental CHF data of the modified surface do not fit the classical models. Therefore, this study proposes a simple model to build the nexus between the surface wettability and the growth of bubbles on the heating surface.     

Augmentation of nucleate boiling heat transfer and critical heat flux using nanoparticle thin-film coatings

Nanoparticle thin-film coatings applied to boiling surfaces using a layer-by-layer (LbL) assembly method demonstrated significant enhancement in the pool boiling critical heat flux (CHF) and nucleate boiling heat transfer coefficient. Up to 100% enhancement of the critical heat flux and over 100% enhancement of the heat transfer coefficient were observed for pool boiling of nickel wires coated with different thin-films of silica nanoparticles. Surface characterization revealed that the surface wettability changed drastically with the application of these coatings, while causing virtually no change in the surface roughness. It is concluded that the nanoporous structure coupled with the chemical constituency of these coatings leads to the enhanced boiling behavior.     

Preparation and pool boiling characteristics of copper nanofluids over a flat plate heater

The copper nanoparticles of average size of 10 nm have been prepared by the sputtering method and characterized through atomic force microscopy (AFM), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The pool boiling heat transfer characteristics of 0.25%, 0.5% and 1.0% by weight concentrations of copper nanoparticles has been studied. Different copper based nanofluids were prepared in both, distilled water and distilled water with 9.0 wt% of sodium lauryl sulphate anionic surfactant (SDS). The pool boiling heat transfer data were acquired for the boiling of nanofluids over a 30 mm square and 0.44 mm thick stainless steel plate heater. The experimental results show that for the critical heat flux of pure water is 80% higher than that of water–surfactant fluid. Also, it was found that the critical heat flux for 0.25%, 0.5% and 1.0% concentrations of copper nanoparticles in copper–water nanofluids are 25%, 40% and 48% higher than that of pure water. But in the case of copper–water with surfactant nanofluids comparing with pure water, the CHF decreases to 75%, 68%, and 62% for respective concentrations of copper nanoparticles. The heat transfer coefficient decreases with increase of nanoparticles concentration in both water–copper and water–copper with surfactant nanofluids.     

The effect of capillary wicking action of micro/nano structures on pool boiling critical heat flux

It is well known that nanoparticles deposited on a heating surface during nanofluids boiling can change the characteristics of the heating surface and increase the critical heat flux (CHF) dramatically. We considered a new approach to investigate the nanoparticle surface effect on CHF enhancement using surfaces modified with artificial micro, nano, and micro/nano structures similar to deposited nanoparticle structures through the anodic oxidation on the zirconium alloy heater. We examined the effect of the capillary wicking action ability on the CHF enhancement due to the micro, nano, and micro/nano structured surfaces. The results demonstrated that the CHF enhancement on the modified surfaces was a consequence of the capillary wicking action ability of the artificial micro/nano structures through the high-speed visualization of the capillary wicking action.     

Experimental study on the pool boiling CHF enhancement using magnetite-water nanofluids

This paper described the effects of a magnetite-water nanofluid (MWNF) on the critical heat flux (CHF) enhancement using an Ni–Cr wire in pool boiling. All experiments were performed at a saturated condition under atmospheric pressure. The CHF values between the MWNF and the other nanofluids with several volume concentrations were compared to evaluate the effect of the MWNF on the CHF enhancement. The CHF values of the MWNF were enhanced from approximately 170% to 240% of pure water as the nanoparticle concentration increased. In addition, the CHF for the MWNF showed the highest value among the evaluated nanofluids. In this paper, three methods were introduced to elucidate the mechanism underlying CHF enhancement. First, scanning electron microscope (SEM) images were obtained to explain the CHF enhancement mechanism due to the deposited nanoparticles, which is related to the surface wettability of the heating surface during the pool boiling. Second, bubble formation in pool boiling was analyzed using image processing to demonstrate the relationship between bubble dynamics and CHF enhancement. Finally, the magnetic field was analytically calculated using the Biot–Savart law to evaluate the effects of the magnetic field on the CHF.     

Role of macrolayer evaporation in pool boiling at high heat flux

Analytical expressions for macrolayer thickness and the rate of heat transfer through a macrolayer in a high heat flux region near the critical value were reported in previous papers by the authors. The results of an experimental investigation into the liquid macrolayer formation are being reported in this paper. The initial thickness of this liquid layer formed between the heated surface and the vapour mass and the frequency of the vapour mass as a function of impressed heat flux have been measured. Using these data, the contribution of macrolayer evaporation to the heat flow from heated surface to bulk has been estimated. Experimental results of macrolayer thickness and frequency of vapour mass have been found to compare well with analytically predicted values. Contribution of heat conduction through the macrolayer has also been found to account for a considerable portion of wall heat flux.     

Molecular dynamics study of wettability and pitch effects on maximum critical heat flux in evaporation and pool boiling heat transfer

Molecular dynamics simulations were employed to investigate the effects of wettability (contact angle) and pitch on nanoscale evaporation and pool boiling heat transfer of a liquid argon thin film on a horizontal copper substrate topped with cubic nano-pillars. The liquid–solid potential was incrementally altered to vary the contact angle between hydrophilic (～0°) and hydrophobic (～127°), and the pitch (distance between nano-pillars) was varied between 21.7 and 106.6?Å to observe the resultant effect on boiling heat transfer enhancement. For each contact angle, the superheat was gradually increased to initiate nucleate boiling and eventually pass the critical heat flux (CHF) into the film boiling regime. The CHF increases with pitch, and tends to decrease substantially with increasing contact angle. A maximum overall heat flux of 1.59?×?10⁸?W/m² occurs at the largest pitch investigated (106.6?Å), and as the contact angle increases the superheat required to reach the CHF condition also increases. Finally, in certain cases of small pitch and large contact angle, the liquid film was seen to transition to a Cassie–Baxter state, which greatly hindered heat transfer.     

CFD modeling for nucleate pool boiling of nanofluids

Boiling is one of the most important processes in almost every industrial heat exchanger arrangement. The present study examines the role played by nanofluids in increasing the heat transfer rate which could improve process efficiency as well as operational cost. The setup consists of a stainless steel vertical cylinder pressure vessel having a horizontal heating rod made of stainless steel submerged in a pool of working fluid (distilled water, alumina/water nanofluid of variable concentration). Simulations were carried out using a 2D geometrical domain in order to calculate values of heat transfer coefficient for different constant heat flux applied on the heater at atmospheric as well as sub atmospheric pressures. For the simulations, a transient Eulerian multiphase involving boiling model was used along with various sub-models involving drag, lift, heat and mass transfer models. The simulated results for the value of heat transfer coefficient were compared and validated from the experimental results.     

Critical heat flux modeling in water pool boiling during power transients

This article suggests a method of the determination of main parameters and dynamic characteristics of heat transfer crisis on a surface of fast heated wall. The new physical models describing process of transition from nucleate to film boiling are presented. The results of transient critical heat flux modeling are compared with the experimental data for saturated water pool boiling under atmospheric pressure.     

Effects of a flow disturbing plate on pool boiling heat transfer

Effects of width and location of a flow disturbing circular plate on nucleate pool boiling heat transfer of water at atmospheric pressure have been investigated experimentally. Through the tests, changes in the degree of intensity of liquid agitation and its effect on heat transfer on a heated tube have been analyzed. According to the results, the plate changes fluid flow around the tube as well as heat transfer coefficients on the tube. It is identified that plate width changes the rate of circulating flow whereas its location changes the growth of active agitating flow. Moreover, flow chugging was observed at the downside of the plate.     

Studies on critical heat flux in flow boiling at near critical pressures

Experimental studies on critical heat flux (CHF) have been conducted in a uniformly heated vertical tube of 12.7 mm internal diameter and 3 m length at different reduced pressures ranging from 0.24 to 0.99 with R-134a as the working fluid. The onset of CHF was determined by the sudden rise in the wall temperature of the electrically heated tube. Experiments were performed over a wide range of parameters: mass flux values from 200 to 2000 kg/m² s, pressure from 10 to 39.7 bars and heat flux from 2 to 80 kW/m² and exit quality from 0.17 to 0.94. The results show considerably lower critical heat flux at high pressures. Well known CHF prediction methods, such as the look-up table and correlations of earlier workers show poor agreement at high pressures. A new correlation has been proposed to estimate the CHF in uniformly heated vertical tubes up to the critical pressure and over a wide range of parameters.