PCBN刀具干车淬硬钢时倒棱前角对切削力和刀具磨损的影响

PCBN刀具磨出负倒棱是为了加强刀具的刃口强度，以减少刀具加工时可能出现的破损情况。本文通过对PCBN刀具加工淬硬轴承钢GCr15的一系列试验数据加以分析，得出倒棱前角和切削力、刀具磨损之间的关系，进而得出在实际加工情况下应该采用的最佳倒棱前角值。试验表明：当倒棱前角取15度且切削速度为125m／s时，刀具具有最好的加工效果，不但切削力可以达到最小值，刀具磨损最轻，而且刀具寿命也达到了最大值。     

PCBN刀具切削性能和磨损机理研究综述

聚晶立方氮化硼(PCBN)刀具是继聚晶金刚石刀具之后的又一种超硬刀具,以其独特的“以车代磨”、“硬态加工”、“干式切削”等方式被誉为21世纪的绿色环保刀具。PCBN刀具在金属切削方面具有广泛的应用,主要用来加工各种淬硬钢、耐磨铸铁等铁基材料。本文介绍了PCBN刀具成分、几何形状、切削参数等对其切削性能的影响,在此基础上分析了不同材料加工时刀具的主要磨损机理,还简单对比了硬质合金和PCBN刀具切削性能上的差异。      

Tool wear and machining performance of cBN–TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel

PCBN is the dominant tool material for hard turning applications due to its high hardness, high wear resistance, and high thermal stability. However, the inflexibility of fabricating PCBN inserts with complex tool geometries and the prohibitive cost of PCBN inserts are some of the concerns in furthering the implementation of CBN based materials for hard turning. In this paper, we present the results of a thorough investigation of cBN plus TiN (cBN–TiN) composite-coated, commercial grade, carbide inserts (CNMA 432, WC–Co (6% Co)) for hard turning applications in an effort to address these concerns. The effect of cutting speed and feed rate on tool wear (tool life), surface roughness, and cutting forces of the cBN–TiN coated carbide inserts was experimented and analyzed using analysis of variance (ANOVA) technique, and the cutting conditions for their maximum tool life were evaluated. The tool wear, surface roughness, and cutting forces of the cBN–TiN coated and commercially available PCBN tipped inserts were compared under similar cutting conditions. Both flank wear and crater wear were observed. The flank wear is mainly due to abrasive actions of the martensite present in the hardened AISI 4340 alloy. The crater wear of the cBN–TiN coated inserts is less than that of the PCBN inserts because of the lubricity of TiN capping layer on the cBN–TiN coating. The coated CNMA 432 inserts produce a good surface finish (<1.6 μm) and yield a tool life of about 18 min per cutting edge. In addition, cost analysis based on total machining cost per part was performed for the comparison of the economic viability between the cBN–TiN coated and PCBN inserts.     

PCBN刀具硬态车削的磨损机制研究

PCBN刀具用于高速切削、硬态切削、干切削以及加工自动化和难加工材料等先进切削工艺时显示出了卓越的性能,为了推动PCBN刀具在我国的推广使用,充分发挥PCBN刀具的潜能,有必要对PCBN刀具切削过程中的行为规律进行研究。目前国内外已经有很多这方面的研究报道,本文旨在对前人已进行的工作进行一个系统的总结,以期能得到PCBN硬态车削时的主要的磨损机制。     

PcBN刀具车削镍基高温合金切削性能研究

本文研究了刀尖圆弧半径、负倒棱参数、切削速度、PcBN材质及干湿切削对PcBN刀具车削镍基高温合金GH4169切削性能的影响.试验结果表明:增大刀尖圆弧半径、负倒棱角度或减小负倒棱宽度均会使刀具磨损相应减小;PcBN的磨损随切削速度的提高而增大;DBW85的切削性能优于BZN6 000和BTN100,且其高速下的磨损量...     

Chip formation, cutting forces, and tool wear in turning of Zr-based bulk metallic glass

The chip light emission and morphology, cutting forces, surface roughness, and tool wear in turning of Zr-based bulk metallic glass (BMG) material are investigated. Machining results are compared with those of aluminum 6061-T6 and AISI 304 stainless steel under the same cutting conditions. This study demonstrates that the high cutting speeds and tools with low thermal conductivity and rake angle activate the light emission and chip oxidation in BMG machining. For the BMG chip without light emission, serrated chip formation with adiabatic shear band and void formation is observed. The cutting force analysis further correlates the chip oxidation and specific cutting energy and shows the significant reduction of cutting forces for machining BMG at high cutting speeds. The machined surface of BMG has better surface roughness than that of the other two work materials. Some tool wear features, including the welding of chip to the tool tip and chipping of the polycrystalline cubic boron nitride (PCBN) tool edge, are reported for turning of BMG. This study concludes that BMG can be machined with good surface roughness using conventional cutting tools.     

PCBN刀具断续车削淬硬钢的试验研究

为了探索PCBN刀具在断续切削条件下刀具的破损规律,选用两种不同的PCBN刀具,在不同强度的断续方式及不同的切削速度下,对淬硬钢进行车削试验研究。根据试验条件,观察了刀具前、后刀面的磨损及破损情况,分析了刀具的失效机理,比较了刀具的切削寿命。结果表明：断续强度严重影响PCBN刀具的使用寿命,断续强度越高,刀具寿命越低;在相同强度的断续条件下,切削速度影响刀具的使用寿命,切削速度越高,刀具的寿命越低;本实验所用的断续条件下,刀具的失效判据为崩刃。     

PCBN超硬刀具研究与进展

现代刀具切削速度的不断提高和先进的集成制造系统的发展对现代刀具的性能提出了更高的要求,刀具材料质量、性能和可靠性直接影响生产效率和加工质量,也直接影响整个制造行业的生产技术水平和经济效益,所以开发高稳定性和良好耐磨性的超硬刀具是当今的发展趋势。本文介绍了超硬材料PCBN超硬刀具的国内外发展概况和刀具性能应用,PCBN超硬刀具材料的制备方法及刀具制造过程,PCBN超硬刀具的断屑槽、修光刃结构以及新型PCBN超硬刀具,刀具车削仿真的相关研究等;并对PCBN超硬刀具及整个刀具行业的前景进行展望。      

聚晶立方氮化硼刀具磨损与寿命研究综述

聚晶立方氮化硼(PCBN)是一种超硬刀具材料,由于其具有硬度高、化学稳定性和热稳定性好等优点,已经被广泛应用于汽车、航空航天、能源等领域的机械零部件加工。文中分析了PCBN刀具的主要磨损形式及其原因,并从刀具材料构成和几何形状、工件材料以及切削条件3个方面总结了影响PCBN刀具磨损和寿命的主要因素,最后介绍了切削参数优化和添加涂层等方法在提高刀具耐磨性与寿命方面的应用。     

The effect of the multi-layer surface coating of carbide inserts on the cutting forces in turning operations

In this paper, the effects of the multi-layer hard surface coating of cutting tools on the cutting forces in steel turning are presented and discussed, based on an experimental investigation with different commercially available carbide inserts and tool geometries over a range of cutting conditions. The cutting forces when turning with surface coated carbide inserts are assessed and compared qualitatively and quantitatively with those for uncoated tools. It is shown that hard surface coatings reduce the cutting forces, although the reduction is marginal under lighter cutting conditions. The cutting force characteristics for surface coated tools are also discussed and shown to have similar trends to those of uncoated tools.     

Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks

In machining of parts, surface quality is one of the most specified customer requirements. Major indication of surface quality on machined parts is surface roughness. Finish hard turning using Cubic Boron Nitride (CBN) tools allows manufacturers to simplify their processes and still achieve the desired surface roughness. There are various machining parameters have an effect on the surface roughness, but those effects have not been adequately quantified. In order for manufacturers to maximize their gains from utilizing finish hard turning, accurate predictive models for surface roughness and tool wear must be constructed. This paper utilizes neural network modeling to predict surface roughness and tool flank wear over the machining time for variety of cutting conditions in finish hard turning. Regression models are also developed in order to capture process specific parameters. A set of sparse experimental data for finish turning of hardened AISI 52100 steel obtained from literature and the experimental data obtained from performed experiments in finish turning of hardened AISI H-13 steel have been utilized. The data sets from measured surface roughness and tool flank wear were employed to train the neural network models. Trained neural network models were used in predicting surface roughness and tool flank wear for other cutting conditions. A comparison of neural network models with regression models is also carried out. Predictive neural network models are found to be capable of better predictions for surface roughness and tool flank wear within the range that they had been trained.Predictive neural network modeling is also extended to predict tool wear and surface roughness patterns seen in finish hard turning processes. Decrease in the feed rate resulted in better surface roughness but slightly faster tool wear development, and increasing cutting speed resulted in significant increase in tool wear development but resulted in better surface roughness. Increase in the workpiece hardness resulted in better surface roughness but higher tool wear. Overall, CBN inserts with honed edge geometry performed better both in terms of surface roughness and tool wear development.     

The total energy and the total entropy of force signals — new parameters for monitoring oblique turning operations

In unmanned CNC turning operations, the accuracy of tool wear predictions is very important for accurate tool replacement policies and avoiding unnecessary tool insert changes. This paper introduces two new parameters, namely the total energy and the total entropy of force signals, for tool condition monitoring. The correlation between the new parameters, tool wear and a wide range of cutting conditions is examined. The experimental results show that the energy of force signal can be reliably used to monitor tool flank and crater wear over a wide range of cutting conditions. However, the total entropy of forces does not appear to be sensitive to feed rate, rake angle and tool wear. The experimental results also indicate that crater wear causes an increase in the effective rake angle resulting in lower total energy of forces. For some particular shapes of worn tool, however, the crater wear results in a decreased rake angle which increases the total energy of forces. The influence of crater wear on forces and the root mean square of acoustic emission (AErms) signals is also observed in this research.     

Evaluation of layer adhered on PCBN tools during turning of AISI D2 steel

Polycrystalline cubic boron nitride (PCBN) tools have high abrasion resistance and are thus suitable for application in the machining of steels with a high volume fraction of primary carbides in their microstructure. These tools are usually applied in the machining of steels with hardness above 45–50 HRC and in the case of application to steels with hardness below 45 HRC, the formation of an adhered layer on the rake face of the tools often occurs. This paper reports a study on the impact of the layer adhered on PCBN tools during the turning of AISI D2 steel, with 35 and 50 HRC. The microhardness and microstructure of the adhered material were determined, as well as the tool wear based on volumetric wear parameters. The layer adhered on the PCBN tool rake face has the same chemical elements as the machined steel alloy. Its microstructure is oriented in the direction of the chip flow and the primary carbides were fragmented. For the sample with 35 HRC the amount of material adhered (W_AM) on the rake face of the PCBN tool was approximately 360% higher than the steel with 50 HRC. The material layer adhered on the PCBN tool rake surface in the case of the 35 HRC steel acts as an edge (assuming the cutting function), while for the 50 HRC steel, the adhered layer intensifies the adhesion wear mechanism through spalling on the tool rake face. The results obtained provide important information for the selection of materials and grades for the development of new cutting tools.     

Statistical analysis of surface roughness and cutting forces using response surface methodology in hard turning of AISI 52100 bearing steel with CBN tool

The present work concerns an experimental study of hard turning with CBN tool of AISI 52100 bearing steel, hardened at 64 HRC. The main objectives are firstly focused on delimiting the hard turning domain and investigating tool wear and forces behaviour evolution versus variations of workpiece hardness and cutting speed. Secondly, the relationship between cutting parameters (cutting speed, feed rate and depth of cut) and machining output variables (surface roughness, cutting forces) through the response surface methodology (RSM) are analysed and modeled. The combined effects of the cutting parameters on machining output variables are investigated while employing the analysis of variance (ANOVA). The quadratic model of RSM associated with response optimization technique and composite desirability was used to find optimum values of machining parameters with respect to objectives (surface roughness and cutting force values). Results show how much surface roughness is mainly influenced by feed rate and cutting speed. Also, it is underlined that the thrust force is the highest of cutting force components, and it is highly sensitive to workpiece hardness, negative rake angle and tool wear evolution. Finally, the depth of cut exhibits maximum influence on cutting forces as compared to the feed rate and cutting speed.     

Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials

This paper deals with an experimental and analytical investigation into the different factors which influence the temperature distribution on Al₂O₃---TiC ceramic tool rake face during machining of difficult-to-cut materials, such as case hardened AISI 1552 steel (60–65 Rc) and nickel-based superalloys (e.g. Inconel 718). The temperature distribution was predicted first using the finite element analysis. Temperature measurements on the tool rake face using a thermocouple based technique were performed and the results were verified using the finite element analysis. Experiments were then performed to study the effect of cutting parameters, different tool geometries, tool conditions, and workpiece materials on the cutting edge temperatures. Results presented in this paper indicate that for turning case hardened steel, increasing the cutting speed, feted, and depth of cut will increase the cutting edge temperature. On the other hand, increasing the tool nose radius, and angle of approach reduces the cutting edge temperature, while increasing the width of the tool chamfer will slightly increase the cutting ege temperature. As for the negative rake angle, it was found that there is an optimum value of rake angle where the cutting edge temperature was minimum. For the Inconel 718 material, it was found that the cutting edge temperature reached a minimum at a speed of 510 m/min, and feed of 1.25 mm/rev. However, the effect of the depth of cut and tool nose radius was almost the same as that determined in the turning of case hardened steel. It was also observed in turning Inconel 718 with ceramic tools that, cutting forces and different types of tool wear were reduced with increasing the feed.     

Machining of hardened steel—Experimental investigations,performance modeling and cooling techniques: A review

The researchers have worked on many facets of machining of hardened steel using different tool materials and came up with their own recommendations. Researchers have tried to investigate the effects of cutting parameters, tool materials, different coatings and tool geometry on different machinability aspects like, the tool life, surface roughness, cutting forces, chip morphology, residual stresses and the tool–chip interface temperature under dry and/or semi-dry and/or flood cooling environment during machining of hardened steels while many of them have ventured to characterize the wear phenomenon. Good amount of research has been performed on an analytical and/or numerical and/or empirical modeling of the cutting forces, tool–chip interface temperature, and tool wear under orthogonal/oblique cutting conditions during machining of hardened steels. This paper presents a comprehensive literature review on machining of hardened steels using coated tools, studies related to hard turning, different cooling methods and attempts made so far to model machining performance(s) so as to give proper attention to the various researcher works.     

PCBN刀具高速切削淬硬钢材料的研究

以PCBN复合片为刀具材料进行相关力学性能分析,并将其制成SNGN120408型刀具后在刀具机床上进行淬硬钢切削试验.分析结果表明:PCBN复合片的结合剂主要为TiN和TiB2,其内部结构均匀,且有良好的致密性.切削试验表明:在干式切削淬硬钢的试验中,切削进给量以及切削速度对PCBN刀具的磨损有较为明显的影响.相比于切...     

Influence of asymmetric cutting edge roundings on surface topography

For finishing operations in machining, hardened steel hard turning can compete with grinding operations by means of accuracy and productivity. In the past research focussed on the effect of process parameters and tool macro geometry on the resulting surface roughness. Recent investigations show, that the cutting edge micro geometry is an important factor to influence surface quality. The knowledge generated by new methods displays the importance of asymmetric cutting edge roundings on cutting forces, chip formation and tool life. It is known, that chip formation also affects the resulting surface quality. Therefore, this paper investigates the effect of asymmetric cutting edge roundings on the resulting surface roughness in hard turning of roller bearing inner rings. Cutting tests with differently shaped cutting edges and two different feed values are conducted. The resulting surface roughness is measured. The consequent surface quality is explained by geometric coherences between uncut chip thickness and stresses along the cutting edge and the effect of material side flow. It is found, that the cutting edge geometry and the resulting stress distribution around the cutting edge affects the generated surface quality.     

Hard turning of an alloy steel on a machine tool with a polymer concrete bed

Finish turning of 39NiCrMo3 alloy steel in the hardened state has been widely investigated under dry, minimum quantity of lubricant and wet cutting conditions, using inserts in ceramic and PCBN materials, on turning centers equipped with polymer concrete and cast iron beds. The progress of workpart surface roughness and tool wear with cutting time has been measured and the results analysed and discussed in detail. It has been observed that dry cutting leads to the lowest values of tool wear and surface roughness, whilst the minimal quantity of lubricant technique does not provide advantages regarding to dry turning. Furthermore, the PCBN inserts are characterised by a longer tool life than the one exhibited by the ceramic inserts. Finally, the outstanding damping and high rigidity of the polymer concrete bed has a beneficial effect on both tool wear and workpiece surface finish.