Surface potential contrasts between silicon surfaces covered and uncovered with an organosilane self-assembled monolayer

Surface potentials of Si substrates covered with a organosilane self-assembled monolayers (SAMs) were measured with reference to the substrate uncovered with the SAM using Kelvin probe force microscopy. Based on a photolithographic technique, the reference surface was prepared in a micrometer scale on each of the samples. SAMs were prepared from n-octadecyltrimethoxysilane [ODS: CH3(CH2)17Si(OCH3)3], 3,3,3-trifluoropropyltrimethoxysilane [FAS3: CF3(CH2)2Si(OCH3)3], heptadecafluoro-1,1,2,2-tetahydro-decyl-1-trimethoxysilane [FAS17: CF3(CF2)7(CH2)2Si(OCH3)3] or n-(6-aminohexyl) aminopropyltrimethoxysilane [AHAPS: H2N(CH2)6NH(CH2)3Si(OCH3)3) by chemical vapor deposition. Potentials of the surfaces covered with ODS-, FAS3- and FAS17-SAMs became more negative than the uncovered Si substrate, while the surface covered with AHAPS-SAM showed a more positive surface potential than the reference. The potential contrasts of these SAMs to the reference were -25, -170, -225 and +50 mV for ODS-, FAS3-, FAS17- and AHAPS-SAMs, respectively. These results almost agreed with potentials expected from the dipole moments of the corresponding precursor molecules estimated by ab initio molecular orbital calculation, except for FAS3-SAM. Despite FAS3 molecule having a larger dipole moment than FAS17 molecule, the surface potential contrast of FAS3-SAM was smaller than that of FAS17-SAM, since surface coverage of FAS3-SAM was relatively incomplete compared with the other SAMs.     

Observation of self-assembled fluorescent beads by scanning near-field optical microscopy and atomic force microscopy

Optical response and topography of fluorescent latex beads both on flat self-assembled monolayer and on a micron-patterned surface with poly(dimethylsiloxane) are studied. Scanning near-field optical microscopy and atomic force microscopy were utilized together for detecting fluorescence and imaging topography of the patterned latex beads, respectively. As a result, the micro-patterned latex beads where a specific chemical binding occurred show a strong signal, whereas no signals are observed in the case of nonspecific binding. With fluorescein isothiocyanate (FITC), it is convenient to measure fluorescence signal from the patterned beads allowing us to monitor the small balls of fluorescent latex.     

Localized etching of silicon in water using a catalytically active platinum-coated atomic force microscopy probe

This paper presents a novel atomic force microscopy (AFM)-based nanofabrication technique for Si in water that is based on highly localized catalytic etching with a Pt-coated AFM probe. It has been shown that nanoscale grooves can be fabricated on the Si surface at room temperature via Pt-assisted catalytic chemical etching in water without the addition of any chemicals. Furthermore, dissolved oxygen (O₂) in water has been found to be a key element for driving the chemical reaction of Si with water in the Si removal process. Experimental results have also suggested that an oscillating cantilever of the Pt-coated AFM probe for the stirring of water is essential in order to overcome the oxygen mass-transfer limitations and enhance the Si removal rate. The elementary chemical reactions taking place during the etching of Si has been estimated on the basis of electrochemical theory. It is proposed that in the first step, dissolved oxygen is reduced and forms hydroxide ions (OH⁻) with water molecules (H₂O) on the surface of the Pt-coated tip. In the second step, Si atoms are oxidized on reaction with OH⁻ ions and water soluble silicates are formed. The catalytic reaction taking place on the surface of a Pt-coated tip can be enhanced by the application of an anodic potential to an additional Pt wire electrode, resulting in a dramatic fifty-fold increase in the Si removal rate.     

Analysis of simulated scanning of atomic-scale silicon surface by atomic force microscopy

This study constructs a contact-mode atomic force microscopy (AFM) simulation measurement model with constant force mode to simulate and analyze the outline scanning measurement by AFM. The simulation method is that when the probe passes the surface of sample, the action force of the atom of sample received by the atom of the probe can be calculated by using Morse potential. Through calculation, the equivalent force on the cantilever of probe can be acquired. By using the deflection angle equation for the cantilever of probe developed and inferred by this study, the deflection angle of receiving action force can be calculated. On the measurement point, as the deflection angle reaches a fixed deflection angle, the scan height of this simulation model can be acquired. By scanning in the right order, the scan curve of the simulation model can be obtained. By using this simulation measurement model, this study simulates and analyzes the scanning of atomic-scale surface outline. Meanwhile, focusing on the tip radii of different probes, the concept of sensitivity analysis is employed to investigate the effects of the tip radius of probe on the atomic-scale surface outline. As a result, it is found from the simulation on the atomic-scale surface that within the simulation scope of this study, when the tip radius of probe is greater than 12 nm, the effects of single atom on the scan curve of AFM can be better decreased or eliminated.     

Effects of substrates on biofilm formation observed by atomic force microscopy

Formation of biofilm is known to be strongly dependent on substrates including topography, materials, and chemical treatment. In this study, a variety of substrates are tested for understanding biofilm formation. Sheets of aluminum, steel, rubber, and polypropylene have been used to examine their effects on formation of Pseudomonas aeruginosa biofilm. In particular, the morphological variation, transition, and adhesiveness of biofilm were investigated through local measurement by atomic force microscopy (AFM). Mechanism of removing biofilm from adhering to substrate is also analyzed, thus the understanding of the mechanism can be potentially useful to prevent the biofilm formation. The results reveal that formation of biofilm can remain on rough surface regardless of substrates in hot water, which may easily induce extra-polymeric substances detachment from bacterial surface. By probing using AFM, local force–distance characterization of extra-cellular materials extracted from the bacteria can exhibit the progress of the biofilm formation and functional complexities.     

Morphological investigation of various orthodontic lingual bracket slots using scanning electron microscopy and atomic force microscopy

Various labial and lingual orthodontic appliances with aesthetic materials have been developed due to an increased demand in aesthetic orthodontic treatment. However, there are few reports regarding the morphology of lingual orthodontic appliances. Therefore, this study evaluates the roughness of slot surfaces of various orthodontic lingual brackets using field emission scanning electron microscopy (FE‐SEM) and atomic force microscopy (AFM). Three types of stainless steel lingual brackets (Stealth^®, 7th Generation^®, and Clippy L^®) and one gold lingual bracket (Incognito?) with a slot size of 0.018 inches × 0.025 inches (0.457 × 0.635 mm²) were selected as representative lingual materials. Both FE‐SEM and AFM examinations showed that the Stealth^® and Clippy L^® brackets had the lowest surface roughness, while the 7th Generation^® bracket had the highest surface roughness. There was a significant difference in surface morphology between the types of lingual brackets, even when composed of the same material. The surface roughness of the bracket slot was dependent on the manufacturing process or surface polishing process rather than the fundamental properties of the bracket materials. There was no significant difference in the mean surface roughness of the slot floor between gold and stainless steel lingual brackets. These findings suggest that, although the gold lingual bracket is very expensive, it has great potential for use in patients with nickel allergy.     

Comparative atomic force and scanning electron microscopy: an investigation on fenestrated endothelial cells in vitro

Rat liver sinusoidal endothelial cells (LEC) contain fenestrae, which are clustered in sieve plates. Fenestrae control the exchange of fluids, solutes and particles between the sinusoidal blood and the space of Disse, which at its back side is flanked by the microvillous surface of the parenchymal cells. The surface of LEC can optimally be imaged by scanning electron microscopy (SEM), and SEM images can be used to study dynamic changes in fenestrae by comparing fixed specimens subjected to different experimental conditions. Unfortunately, the SEM allows only investigation of fixed, dried and coated specimens. Recently, the use of atomic force microscopy (AFM) was introduced for analysing the cell surface, independent of complicated preparation techniques. We used the AFM for the investigation of cultured LEC surfaces and the study of morphological changes of fenestrae. SEM served as a conventional reference.
AFM images of LEC show structures that correlate well with SEM images. Dried-coated, dried-uncoated and wet-fixed LEC show a central bulging nucleus and flat fenestrated cellular processes. It was also possible to obtain height information which is not available in SEM. After treatment with ethanol or serotonin the diameters of fenestrae increased (+6%) and decreased (−15%), respectively. The same alterations of fenestrae could be distinguished by measuring AFM images of dried-coated, dried-uncoated and wet-fixed LEC. Comparison of dried-coated (SEM) and wet-fixed (AFM) fenestrae indicated a mean shrinkage of 20% in SEM preparations. In conclusion, high-resolution imaging with AFM of the cell surface of cultured LEC can be performed on dried-coated, dried-uncoated and wet-fixed LEC, which was hitherto only possible with fixed, dried and coated preparations in SEM and transmission electron microscopy (TEM).     

Dynamic variations in adhesion of self-assembled monolayers on nanoasperities probed by atomic force microscopy

Octadecyltriethoxysilane (OTE) self- assembled monolayers (SAMs) and their effects on friction and adhesion have been investigated on various combinations of functionalized and unfunctionalized silicon oxide surfaces including the oxidized surface of crystalline Si(100), silica nanoparticle films, and oxidized Si atomic force microscopy (AFM) tips. Force-distance spectroscopy was utilized to probe and compare the properties of the OTE SAMs on silica asperities with nanoscale curvature against these same monolayers on surfaces with sub-1 nm roughness (flat surfaces). It was found that adhesion between SAMs and silicon oxide surfaces can vary significantly when assembly takes place on surfaces with nanoscopic curvature as compared to flat surfaces. Observations indicate that the SAM structure present during force measurements is dynamic in nature, which yields different adhesion values when measured with variations of both tip-sample contact time and tip-approach/retract rates. These results point the need in reporting a number of measurement parameters when probing adhesion by SAM functionalized tips.     

Effects of probe pollutants on morphological and mechanical measurements of muscle and collagen fibers using atomic force microscopy

Because of the interaction between probes and samples, pollutants in buffer solution or in the air would easily bind to probes and make the probe polluted, which might influence the morphological and mechanical measurements with atomic force microscopy. The polluted probes might transfer the pollutants onto the samples and thus change the surface ultrastructure of samples, or collect the deviated feedback signals to make the phantasm images. The former process is irreversible even if a new probe is employed, and the latter one is a reversible process as long as changing the used/polluted probe. Effects of polluted probes on morphological and mechanical characteristics of insect flight muscle and rat tail tendon collagen I fibers had been discussed in this study, in which, we constructed a series of methods to avoid/reduce the collecting of phantasm images and deviated mechanical information, such as changing the scanning direction and scanning force, replacing the new probes, or cleaning the polluted probes. SCANNING 32:113–121, 2010. © 2010 Wiley Periodicals, Inc.     

Study of fibrinogen adsorption on self-assembled monolayers on Au(111) by atomic force microscopy

The adsorption of plasma protein fibrinogen on the self-assembled monolayers (SAMs) of n-hexadecyl mercaptan and citrate was investigated with atomic force microscopy (AFM). On the basis of the preparation of these two flat SAMs on Au(111), high-resolution AFM images of bovine fibrinogen were obtained with different protein concentrations. The results indicated that the surface chemical composition significantly affected the adsorption behavior of fibrinogen. Since fibrinogen plays a key role in the regulation of both haemostasis and thrombosis, high-resolution AFM imaging on SAMs is expected to be an effective approach to study the haemocompatibility of materials with different surface chemistry.     

基于硅悬臂高阶谐振的动态原子力显微镜的快速扫描

利用原子力显微镜(AFM)硅悬臂器件具有多阶谐振模态的特性,提出了基于硅悬臂高阶谐振特性构建动态AFM来实现快速扫描的方法,并研制了可工作于一阶模态和高阶模态的AFM。介绍了高阶谐振AFM系统的基本结构和工作原理,从理论上证明了利用硅悬臂梁高阶谐振特性实现快速扫描的可行性。以自制的AFM为研究对象,分析了影响动态AFM扫描速度的主要因素,对系统各模块的响应时间进行了分析、测试,并通过实验证明了AFM在二阶谐振模态下的稳定时间明显小于一阶谐振模态下的稳定时间。最后,分别用一阶、二阶谐振模态对光栅试样在同一区域的表面形貌进行了扫描测试,测试数据表明:在相同条件下,AFM的扫描速度在二阶谐振模态下约是一阶模态下的3.3倍。理论分析和实验结果证明了利用高阶谐振探针提高AFM扫描速度的可行性和有效性。     

Quality assessment of atomic force microscopy probes by scanning electron microscopy: correlation of tip structure with rendered images

While image quality from instruments such as electron microscopes, light microscopes, and confocal laser scanning microscopes is mostly influenced by the alignment of optical train components, the atomic force microscope differs in that image quality is highly dependent upon a consumable component, the scanning probe. Although many types of scanning probes are commercially available, specific configurations and styles are generally recommended for specific applications. For instance, in our area of interest, tapping mode imaging of biological constituents in fluid, double ended, oxide-sharpened pyramidal silicon nitride probes are most often employed. These cantilevers contain four differently sized probes; thick- and thin-legged 100 microm long and thick- and thin-legged 200 microm long, with only one probe used per cantilever. In a recent investigation [Taatjes et al. (1997) Cell Biol. Int. 21:715-726], we used the scanning electron microscope to modify the oxide-sharpened pyramidal probe by creating an electron beam deposited tip with a higher aspect ratio than unmodified tips. Placing the probes in the scanning electron microscope for modification prompted us to begin to examine the probes for defects both before and after use with the atomic force microscope. The most frequently encountered defect was a mis-centered probe, or a probe hanging off the end of the cantilever. If we had difficulty imaging with a probe, we would examine the probe in the scanning electron microscope to determine if any defects were present, or if the tip had become contaminated during scanning. Moreover, we observed that electron beam deposited tips were blunted by the act of scanning a hard specimen, such as colloidal gold with the atomic force microscope. We also present a mathematical geometric model for deducing the interaction between an electron beam deposited tip and either a spherical or elliptical specimen. Examination of probes in the scanning electron microscope may assist in interpreting images generated by the atomic force microscope.     

Artificially induced unusual shape of erythrocytes: an atomic force microscopy study

We used air operating atomic force microscopy (AFM) to study several morphological modifications of human erythrocytes, artificially produced by addition of exogenous agents including phospholipids, low ionic strength media and drugs. Most experiments were performed on unfixed samples to avoid treating red blood cells (RBCs) with chemical agents that can, in principle, induce morphological alteration.
After detailed quantitative AFM characterization, the artificially produced abnormally shaped RBCs were compared with cells that occur with high incidence in blood pathologies. This morphological approach suggests a new strategy to describe and understand the biochemical and/or mechanical modifications responsible for the underlying pathologically induced changes and prove AFM to be a suitable tool to study erythrocyte deformation.     

In vivo assessment of the corrosion of nickel–titanium orthodontic archwires by using scanning electron microscopy and atomic force microscopy

This study was undertaken to assess in vivo the corrosion in two commercial nickel–titanium (NiTi) orthodontic archwires removed from the oral cavity of patients using fluoride mouthwashes. Five volunteers took part in this study on the corrosion behavior of two brands of NiTi archwires (3M and AO (brand of archwire)) during use of two mouthwashes with neutral sodium fluoride 1.1%, one with acidulated fluoride 1.1%, and one with placebo and a control group. Each patient used one mouthwash in three different periods of time for 1 min a day for 30 days. The archwires were assessed with scanning electron microscopy and atomic force microscopy for qualitative and quantitative analysis. The values obtained with atomic force microscopy (AFM) were submitted to normality test, two‐way analysis of variance, and Tukey's test at a significance level of 5%. The AFM images showed a gradual qualitative increase in the roughness of both types of wire between the treatments: control < placebo < neutral fluoride < acidulated fluoride. The arithmetic average of the roughness and root mean square of the roughness were similar. As for 3M archwires, only the acidulated fluoride group differed statistically from the others. As for AO archwires, the control and placebo groups did not differ from each other, but differed from the other fluoride treatments. The group using neutral fluoride also differed significantly from the acidulated fluoride group. 3M archwires were not affected by daily oral challenges. AO archwires were not affected by daily oral challenges either; their association with fluoride, either neutral or acidulated, increased their roughness.     

Note: A scanning electron microscope sample holder for bidirectional characterization of atomic force microscope probe tips

A novel sample holder that enables atomic force microscopy (AFM) tips to be mounted inside a scanning electron microscopy (SEM) for the purpose of characterizing the AFM tips is described. The holder provides quick and easy handling of tips by using a spring clip to hold them in place. The holder can accommodate two tips simultaneously in two perpendicular orientations, allowing both top and side view imaging of the tips by the SEM.     

Characteristics of a dynamic atomic force microscopy based on a higher-order resonant silicon cantilever and experiments

In order to improve the sensitivity and scanning speed of the dynamic AFM, a surface scanning method using higher-order resonant cantilever is adopted and investigated based on the higher-order resonance characteristics of the silicon cantilever, and the theoretical analysis and experimental verification on the higher-order resonance characteristics of the corresponding dynamic AFM cantilever are given. In this method, the cantilever is excited to oscillate near to its higher-order resonant frequency which is several times higher than that of the fundamental mode. Then the characteristic changes a lot compared with the first-order resonant cantilever. Because of the changes of the quality factor, amplitude and the mode shape of the cantilever, the higher-order resonant AFM gets higher sensitivity and scanning speed. Based on the home-built tapping-mode AFM experiment system, the resolution and the response time of the first and second order resonance measured by experiment are respectively: 0.83 nm, 0.42 nm; 1265 μs, 573 μs. The higher-order resonance cantilever has higher sensitivity and the dynamic measurement performance of the cantilever is significantly improved from the experimental results. This can be a useful method to develop AFM with high speed and high sensitivity. Besides above, the surface profile of a grating sample and its three-dimensional topography are obtained by the higher-order resonant mode AFM.     

Study on effect of hydrogen treatment on amorphous carbon film using scanning probe microscopy

Amorphous carbon film was treated by hydrogen plasma. The change of surface structure, conductivity, and work function distribution is characterized by scanning probe microscope technique and local electron emission is also analyzed. We find that chemical effect of hydrogen plasma on the a-C film is small, but the etching effect is strong and the surface morphology and conductance are obviously changed after hydrogen treatment. Electron emission enhancement is not due to the decrease of work function or existence of sp² conductive channels, but from the mutual effect between sp² and sp³ phase. We suggest that the enhancement is due to the internal electron injection from the sp²-rich interface layer into the surface sp³-rich grains.