用LC/APCI/MS方法检测粉尘中的炸药成分

采用高选择性和灵敏度的LC(液相色谱)/APCI(大气压化学电离源)/MS(质谱)方法定量分析粉尘样品中的HMX、RDX、PETN、CE、NQ和TNT。采用ASE萃取,GPC净化浓缩作为前处理方法,在粉尘中分别添加所测炸药组分,用丙酮作为ASE萃取溶剂,乙酸乙酯和环己烷(体积比为1∶1)作为GPC净化时的流动相并抛弃杂质500s,收集1 520s。在LC/MS分析时,通过在流动相中添加1mmol/L甲酸与样品形成[M+HCOO]-的甲酸加合离子。结果表明,HMX、RDX、PETN、CE、NQ、TNT的方法检测限分别为0.78,1.44,1.69,0.77,1.06,1.72ng/mL,回收率为49.0%～88.4%,相对标准偏差为3.5%～10.3%。该方法可以用来系统排查及定量分析爆炸残留物及环境样品中的NQ、RDX、PETN、CE、HMX、TNT成分。     

NH_3和ClO_3对RDX初始热裂解的影响

用B3LYP/6-31G(d)方法,优化得到RDX及其与高氯酸铵(AP)裂解产物NH3、ClO3形成复合物的稳定构型,计算了RDX及各复合物的N-NO2键解离能.结果表明,复合物中RDX构型变化不是很大,但其CS对称性遭到破坏.RDX与NH3、ClO3结合后其N-NO2键解离能与RDX相比变化不大, NH3、ClO3的存在不影响RDX硝基裂解A位优先于E位的顺序.但一旦复合物裂解,生成的NO2极易与NH3发生反应,放出大量热,从而可引发RDX的后续裂解反应.     

Anaerobic biodegradation of RDX and HMX with different co-substrates☆

Simulated wastewater of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) was treated under anaerobic conditions with co-substrates such as ammonium chloride, dex-trose, sodium acetic, sodium nitrate and sulfate. The results showed that with nitrogen compounds such as ammonium chloride added as co-substrate, no significant change was observed, indicating that the molar ratio of N/C for RDX and HMX is sufficient for biodegradation. With the addition of dextrose and acetate to the system, biodegradation efficiency was enhanced greatly. For example, with dextrose as the co-substrate, degradation efficiency of 99.1%and 98.5%was achieved for RDX and HMX, respectively, after treatment for 7 days. When so-dium acetic was used as the co-substrate, the enhancement of degradation percentage was similar, but was not as high as that with dextrose, indicating the selectivity of RDX and HMX to co-substrate during anaerobic degrada-tion. With sodium nitrate as the co-substrate, the degradation efficiency of RDX or HMX decreased with the increase of salt concentration. Sodium sulfate has no significant effect on the biodegradation of RDX and HMX. A wel-selected co-substrate should be employed in applications for degradation of RDX and HMX wastewaters.     

Revisitation of Formaldehyde Aniline Condensation. VII. 1,3,5-Triarylhexahydro-sym-triazines and 1,3,5,7-Tetraaryl-1,3,5,7-tetrazocines from Aromatic Amines and Paraformaldehyde

A product study of the reaction between a number of aromatic amines substituted with widely different groups and paraformaldehyde in inert solvents was performed and found to yield 1,3,5-triaryl-1,3,5-hexahydrotriazines, 1,3,5,7-tetraaryl-1,3,5,7-tetrazocines and formaminals. It was not possible to correlate the product outcomes with the actual structure of the amine substrate. The X-ray diffraction structural determination of 1,3,5-tri-(t-butylphenyl)-( 1b ) and 1,3,5-tri-(m-fluorophenyl)-1,3,5-hexahydrotriazine ( 1c ) showed the diaxial arrangement of the N-substituents.     

Kinetic Deuterium Isotope Effects in the combustion of formulated nitramine propellants

The kinetic deuterium isotope effect was used to investigate the rate-limiting process in the combustion of formulated nitramine propellants. Model propellant formulations containing either octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), or their deuteriated analogues were pressed into pellets and burned under nitrogen pressure in a window bomb. The magnitudes of the observed deuterium isotope effects indicate that the HMX and RDX exert significant control over the combustion phenomenon of the propellants studied. Furthermore, assuming a consistent mechanism between decomposition and combustion, the observed isotope effects suggest that a carbon-hydrogen bond rupture in HMX or RDX is the rate-controlling step in the combustion of the model nitramine propellants. Observed isotope effect values for HMX-CW5 and RDX-CW5 formulated propellants at 1000 psig (6.99 MPa) pressure were 1.29 ± 0.09 and 1.24 ± 0.07, respectively, compared to a theoretical estimate of 1.29 for a primary effect due to C H bond rupture at 673 K.     

Study of Plastic Explosives based on Attractive Cyclic Nitramines Part I. Detonation Characteristics of Explosives with PIB Binder

Four plastic explosives based on energetic nitramines and a non‐energetic binder were prepared and studied. The nitramines were RDX (1,3,5‐trinitro‐1,3,5‐triazine), HMX (1,3,5,7‐tetranitro‐1,3,5,7‐tetrazine), BCHMX (cis‐1,3,4,6‐tetranitro‐octahydroimidazo‐[4,5‐d]imidazole) and HNIW (ε‐2,4,6,8,10,12‐hexanitro‐2,4,6,8,10,12‐hexaazaisowurtzitane, ε‐CL‐20). The binder was in all cases polyisobutylene (PIB) as in the standard composition C‐4. These powerful plastic explosives were compared to standard PETN‐based commercially available explosives Semtex 1A and Sprängdeg m/46. The detonation velocities were experimentally measured and compared to the ones calculated by the Kamlet–Jacobs method, CHEETAH and EXPLO5 Codes. The experimental detonation velocities as well as the calculated detonation parameters decrease in the following order: HNIW‐PIB>HMX‐PIB≥BCHMX‐PIB>RDX‐PIB>Sprändeg m/46≥Semtex 1A. Urizar coefficients for the various binders were calculated from experimental data.     

Study of Plastic Explosives based on Attractive Cyclic Nitramines,Part II. Detonation Characteristics of Explosives with Polyfluorinated Binders

A series of plastic bonded explosives (PBXs) based on Viton A and Fluorel binders were prepared using four nitramines, namely RDX (1,3,5‐trinitro‐1,3,5‐triazinane), β‐HMX (β‐1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocane), BCHMX (cis‐1,3,4,6‐tetranitro‐octahydroimidazo‐[4,5‐d]imidazole), and ε‐HNIW (ε‐2,4,6,8,10,12‐hexanitro‐2,4,6,8,10,12‐hexaazaisowurtzitane). The detonation velocities, D, were determined. Detonation parameters were also calculated by means of modified Kamlet & Jacobs method, CHEETAH and EXPLO5 codes. In accordance with our expectations BCHMX based PBXs performed better than RDX based ones. The Urizar coefficient for Fuorel binder was also calculated.     

N2O5硝解三丙酰基三氮杂环己烷制备RDX

以三丙酰基三氮杂环己烷为原料,N2O5/HNO3为硝解剂制备了RDX.分别考察了硝解剂浓度、反应物配比、反应温度和反应时间对RDX产率的影响.结果表明,当N2O5与HNO3的摩尔比为1∶10,N2O5与三丙酰基三氮杂环己烷的摩尔比为6∶1,反应温度为45℃,反应1 h,RDX的最高产率可达92.7%,纯度为98.5%.     

Preparation and Characterization of Hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine/Ammonium Perchlorate Intermolecular Explosives

Hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine/ammonium perchlorate/glycidyl azide polymer (RDX/AP/GAP) intermolecular explosives (IMX) with different proportions of RDX to AP were prepared by sol‐gel method, and the structure and performance was characterized by Brunauer‐Emmett‐Teller measurements (BET), X‐ray diffraction (XRD), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results showed that the specific surface area of RDX/AP/GAP IMX decreased with the addition of AP. The crystals of AP and RDX in RDX/AP/GAP intermolecular explosives were in the range of 20–48 nm and 23–55 nm, respectively. In addition, RDX/AP/GAP intermolecular explosives had the largest heat release at zero balance.     

Degradation of TNT,RDX, and HMX Explosive Wastewaters Using Zero‐Valent Iron Nanoparticles

The high‐energy explosives 2,4,6‐trinitrotoluene (TNT), hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine (RDX), and the high melting explosive octahydro‐1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocine (HMX) are common groundwater contaminants at active and abandoned munitions production facilities causing serious environmental problems. A highly efficient and environmentally friendly method was developed for the treatment of the explosives‐contaminated wastewaters using zero‐valent iron nanoparticles (ZVINs). ZVINs with diameters of 20–50 nm and specific surface areas of 42.56 m² g⁻¹ were synthesized by the co‐precipitation method. The explosives degradation reaction is expressed to be of pseudo first‐order and the kinetic reaction parameters are calculated based on different initial concentrations of TNT, RDX, and HMX. In addition, by comparison of the field emission scanning electron microscopy (FE‐SEM) images for the fresh and reacted ZVINs, it was apparent that the ZVINs were oxidized and aggregated to form Fe₃O₄ nanoparticles as a result of the chemical reaction. The X‐ray diffraction (XRD) and X‐ray absorption near edge structure (XANES) measurements confirmed that the ZVINs corrosion primarily occurred due to the formation of Fe₃O₄. Furthermore, the postulated reaction kinetics in different concentrations of TNT, RDX, and HMX, showed that the rate of TNT removal was higher than RDX and HMX. Furthermore, by‐products obtained after degradation of TNT (long‐chain alkanes/methylamine) and RDX/HMX (formaldehyde/methanol/hydrazine/dimethyl hydrazine) were determined by LC/MS/MS, respectively. The high reaction rate and significant removal efficiencies suggest that ZVINs might be suitable and powerful materials for an in‐situ degradation of explosive polluted wastewaters.     

Micro Videographic Analysis of the Melt Layer of Self‐Deflagrating HMX and RDX

Micro videographic analysis of the thin molten layer on the surface of HMX (Octahydro‐1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocine) and RDX (Hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine) during self deflagration were performed. This was done to gain a better understanding of the physical structure present in this 100–300 μm layer and give a visual picture for the development of computational models. During steady‐state combustion, RDX had a consistent melt layer with vigorous bubble formation. There was a continuous liquid layer throughout combustion and no foam was formed. The surface of HMX during steady‐state combustion at ambient initial temperatures was an uneven layer of foam. Foam appeared to convect across the surface in undulating waves. At elevated initial temperatures, the HMX molten layer was a consistent foam layer in both time and space. Micro videography was also done with a diagnostic laser sheet as illumination to measure the melt layer thickness. The RDX bubbling layer was about 217±30 μm thick. The HMX foam thickness varied from almost nothing to 660 μm, with an average value of about 234±106 μm.     

1,3,5‐Trinitroperhydro‐1,3,5‐triazine (RDX)‐Based Sheet Explosive Formulation with a Hybrid Binder System

A plastic‐bonded explosive (PBX) in the form of a sheet was formulated comprising of 1,3,5‐trinitroperhydro‐1,3,5‐triazine (RDX) and an hybrid binder system containing a linear thermoplastic polyurethane and a fluoroelastomer (Viton). The effect of a fluoroelastomer on the explosive as well as mechanical properties and thermal behavior of sheet explosive formulations were investigated and compared with a control formulation containing 90 % of RDX and 10 % of natural rubber (ISNR‐5). The replacement of 10 % natural rubber by a hybrid binder system led to an increase in the velocity of detonation (VOD) of the order of 250–950 m s⁻¹ and better mechanical properties in terms of tensile strength (1.9–2.5 MPa) compared to the control formulation (RDX/ISNR‐5 (90/10)). The compatibility of ingredients and thermal decomposition kinetics of selected sheet explosive formulations were investigated by vacuum stability tests and differential scanning calorimetry (DSC). The results suggested better compatibility of RDX with the hybrid binder system (polyurethane/Viton), which is useful to reduce potential hazards in handling, processing, and storage.     

Transition Structures of the Electrocyclic Reactions of cis,cis,cis-1,3,5-Cyclooctatriene

The electrocyclic reactions of cis,cis,cis-1,3,5-cyclooctatriene have been studied using ab initio molecular orbital theory. cis,cis,cis-1,3,5-cyclooctatriene can undergo an electrocyclic ring opening in a conrotatory fashion to form cis,cis-1,3,5,7-octatetraene and a disrotatory electrocyclization to form bicyclo[4.2.0]octa-2,4-diene. The transition structures for these electrocyclic reactions have been located. Geometry optimizations employed restricted Hartree-Fock calculations and the 3–21G and 6–31G* basis sets. Electron correlation energies were calculated using second-order, and in some cases fourth-order, Møller-Plesset theory. Scaled RHF/6–31G* force constants were employed in the prediction of secondary deuterium isotope effects for the conrotatory ring opening. The ground state of cis,cis,cis-1,3,5-cyclooctatriene exists in a twist-boat conformation with staggering at the saturated linkage. The transition structure for the conrotatory electrocyclic ring opening to form cis,cis-1,3,5,7-octatetraene has a helical structure, which has implications for the stereoselectivities of ring closure of 1-substituted-cis,cis-1,3,5,7-octatetraenes. The disrotatory transition structure for the electrocyclization to form bicyclo[4.2.0]octa-2,4-diene is strongly distorted from C_s symmetry, in contrast to the transition structure for the disrotatory electrocyclization of cis-1,3,5-hexatriene. This distortion is caused by staggering about the saturated linkage.     

Investigation on the Thermal Expansion and Theoretical Density of 1,3,5‐Trinitro‐1,3,5‐Triazacyclohexane

The CTE and the theoretical density are important properties for energetic materials. To obtain the CTE and the theoretical density of 1,3,5‐trinitro‐1,3,5‐triazacyclohexane (RDX), XRD, and Rietveld refinement are employed to estimate the dimensional changes, within the temperature range from 30 to 170 °C. The CTE of a, b, c axis and volume are obtained as 3.07×10⁻⁵ K⁻¹, 8.28×10⁻⁵ K⁻¹, 9.19×10⁻⁵ K⁻¹, and 20.7×10⁻⁵ K⁻¹, respectively. Calculated from the refined cell parameters, the theoretical density at the given temperature can be obtained. The theoretical density at 20 °C (1.7994 g cm⁻³) is in close match with the RDX single‐crystal density (1.7990 g cm⁻³) measured by density gradient method. It is suggested that the CTE measured by XRD could perfectly meet with the thermal expansion of RDX.     

Sensitivity and Detonation Characteristics of Selected Nitramines Bonded by Sylgard Binder

Four plastic explosives based on cyclic nitramines and polymeric matrix were prepared and studied. The nitramines were RDX (1,3,5‐trinitro‐1,3,5‐triazinane), HMX (1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocane), BCHMX (cis‐1,3,4,6‐tetranitro‐octahydroimidazo‐[4,5‐d]imidazole), and ϵ‐CL20 (ϵ‐2,4,6,8,10,12‐hexanitro‐2,4,6,8,10,12‐hexaazaisowurtzitane, ϵ‐HNIW). Sylgard 184 was used in the all PBXs prepared samples as a binder. The sensitivities to different mechanical stimuli were determined. The detonation velocities were experimentally measured. Detonation characteristics were calculated by EXPLO5 thermodynamic code. For comparison, standard plastic explosives, Composition C4, Semtex 10, and EPX‐1 were studied. Results showed that the experimental detonation velocities as well as the calculated detonation parameters decrease in the following order: CL20‐sylgard>HMX‐sylgard≥BCHMX‐sylgard>RDX‐sylgard. Calculations by EXPLO5 computer program resulted in detonation velocities close to the experimental ones with 3.1 % maximum difference. Urizar coefficient for the Sylgard binder was calculated from experimental data. An inverse linear relationship between friction sensitivity and heat of detonation of the studied samples was observed. Sylgard binder significantly decreased the sensitivity of all the studied nitramines. Among these prepared samples, the properties of BCHMX‐sylgard are similar to other ordinary plastic explosives.     

Removal of 2,4,6-trinitrotoluene (TNT) and 1,3,5-trinitro-1,3,5-triazacyclohexane (RDX) from aqueous solutions with surfactants

2,4,6-Trinitrotoluene (TNT) was found to react in aqueous solution with surfactants containing amino and quaternary ammonium groups at pH 10–11 at ambient temperature. The surfactants investigated included N-tallow 1,3-diaminopropane, trimethyl N-tallow ammonium chloride and N,N,N′,N′,N′-pentamethyl N-tallow 1,3-propane diammonium dichloride. The reaction products were insoluble in water and readily separated through filtration. The dried solids were not explosive and the solids burned without explosion. The results showed that TNT can be reduced to less than 0.1 ppm from the initial concentration of 110 ppm in 2–3 hours. The wastewater of Composition B contains TNT and 1,3,5-trinitro-1,3,5-triazacyclohexane (RDX). Treatment of the wastewater with the ammonium cationic surfactants showed that TNT was removed quantitatively by precipitation and RDX was simultaneously hydrolyzed. The mechanism of this treatment is discussed.     

Simultaneous degradation of 2,4,6-trinitrophenyl-N-methylnitramine (Tetryl) and hexahydro-1,3,5-trinitro-1,3,5 triazine (RDX) in polluted wastewater using some advanced oxidation processes

Here we report the study on the utilization of several advanced oxidation processes such as electro-oxidation and Fenton process in simultaneous treatment of two nitramine explosives: 2,4,6-trinitrophenyl-N-metylnitramine (Tetryl) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX). The preliminary tests indicated that the electrolytic method using a TiO₂/IrO₂/RuO₂-coated electrode could rapidly degrade Tetryl but not RDX. While the addition of certain amount of H₂O₂ induced an increase of Tetryl degradation yield but had insignificant effect on RDX decomposition, the use of Fenton's reagent showed an enhanced efficiency in degradation of both nitramines. It can be concluded that among tested processes, Fenton process is the most effective for treatment of nitramine-containing wastewaters.     

Attractive Nitramines and Related PBXs

At present, cis‐1,3,4,6‐tetranitro‐octahydroimidazo‐[4,5‐d]imidazole (bicyclo‐HMX, BCHMX) and ε‐2,4,6,8,10,12‐hexanitro‐2,4,6,8,10,12‐hexaazaisowurtzitane (ε‐HNIW, CL‐20) are a topic of interest from the attractive and the potentially attainable nitramines. They were chosen to be studied in comparison with 1,3,5‐trinitro‐1,3,5‐triazinane (RDX) and β‐1,3,5,7‐tetranitro‐1,3,5‐tetrazocane (β‐HMX). Marginal attention is devoted also to 4,8,10,12‐tetranitro‐2,6‐dioxa‐tetraazawurtzitane (Aurora 5). BCHMX, ε‐HNIW, RDX, and HMX were studied as plastic bonded explosives (PBXs) with elastic properties based on Composition C4 and Semtex 10 matrices. Also they were studied as a highly pressed PBXs based on the Viton A binder. The detonation parameters and sensitivity aspects of these nitramines and their corresponding PBXs were determined. Relative explosive strengths (RS) of these compositions are mentioned with mutual relationships between the measured RS values and some detonation parameters. These relationships indicate a possibility of changes in detonation chemistry of these mixtures filled mainly by HNIW. A sensitivity of RS‐CL20 (HNIW with reduced sensitivity) is reported and the new findings in the friction sensitivity are discussed.     

1,3,5-三硝基-六氢化-1,3,5-三嗪-2-酮的合成与表征

以尿素、甲醛和叔丁胺为原料,通过Mannich缩合反应制备出5-叔丁基-1,3,5-三嗪-2-酮(TBT),再经硝酸-乙酸酐硝化合成出1,3,5-三硝基-六氢化-1,3,5-三嗪-2-酮(Keto-RDX),用核磁、红外光谱、质谱、元素分析等对TBT和Keto-RDX的结构进行了表征.探讨了TBT环化反应历程,确定了制...     

DFT Studies on a Series of Nitramines Containing Pyridine Ring

In this article, a series of nitramines containing pyridine ring were studied by density functional theory (DFT). The gas-phase heats of formation were predicted based on the isodesmic reactions and the condensed-phase heats of formation and heats of sublimation were estimated with the Politzer's approach. The detonation velocity and pressure were calculated using the empirical Kamlet-Jacobs equation. Many title compounds have better performance than RDX (hexahydro-1,3,5-trinitro-1,3,5-trizine) and HMX (1,3,5,7-tetranitro-1,3,5,7- tetraazacyclooctane). The impact sensitivity was evaluated with the characteristic height (h₅₀). It is found that most of the studied compounds have lower sensitivities than CL-20 (2,4,6,8,10,12-hexanitro-2,4,6,8,10,12- hexaazaisowurtzitane). The crystal structures were predicted with the molecular mechanics method and optimized by the CA-PZ local density approximation of DFT. Analysis of the crystal energy gap indicates I-13, II-1, III-1, and IV-1 are nearly conductors and other compounds are semiconductors. For I-1～I-8 and I-11, the largest contribution to the valence bands is mainly from the p states of the C and N atoms in the pyridine and fused ring and for the other compounds, from the p states of the C and N atoms in the amino group and pyridine.