严重事故条件下安全壳响应模拟研究

压水堆核电厂发生严重事故期间,从主系统释放的蒸汽、氢气以及下封头失效后进入安全壳的堆芯熔融物均对安全壳的完整性构成威胁。以国内典型二代加压水堆为研究对象,采用MAAP程序进行安全壳响应分析。选取了两种典型的严重事故序列：热管段中破口叠加设备冷却水失效和再循环高压安注失效,堆芯因冷却不足升温熔化导致压力容器失效,熔融物与混凝土发生反应（MCCI）,安全壳超压失效;冷管段大破口叠加再循环失效,安全壳内蒸汽不断聚集,发生超压失效。通过对两种事故工况的分析,证实了再循环高压安注、安全壳喷淋这两种缓解措施对保证安全壳完整性的重要作用。     

高压安全注射系统对压水堆全厂断电事故的缓解能力分析

选择一个典型的3环路压水堆作为参考对象,采用最佳估算程序RELAP/SCDAPSIM/MOD3.2建立了一个典型的3环路压水堆严重事故计算模型。分析了全厂断电(SBO)事故引发的堆芯熔化基准事故后,高压安全注射系统对该事故的缓解能力。敏感性分析表明,堆芯出口温度达到920 K时,采用卸压充水缓解措施可以有效地阻止堆芯熔化,维持堆芯长期处于稳定、安全状态。     

注水时机对压水堆严重事故进程的影响

以典型的3环路压水堆为参考对象,建立了详细的严重事故计算模型。选择一回路热段当量直径为18 cm的失水事故(LOCA)作为初始事件,采用RELAP5/SCDAP/MOD3.2为分析工具,对无注水、无缓解措施下的基准事故进程进行计算分析,研究3种不同注水时机对严重事故进程的影响。3种注水时机分别为堆芯表面峰值温度达到1100 K、1300 K、1500 K时开始注水。计算结果显示,压水堆严重事故进程对于注水的时机非常敏感。较早阶段的注水对于阻止堆芯熔化十分有效,注水较晚会恶化事故进程,加速堆芯熔化。     

稳压器卸压阀卸压效果研究

基于国际上模拟严重事故瞬态过程最详细的机理性程序SCDAP/RELAP5/MOD3.1,主要分析研究了核电站未紧急停堆的预期瞬变(ATWS)初因(失去主给水、失去厂外电和控制棒失控提升)叠加辅助给水失效导致的堆芯熔化严重事故进程,并验证阻止ATWS导致堆芯熔化进程的一次侧卸压缓解措施的充分性和有效性.计算分析结果显示,一列稳压器卸压阀不足以充分降低一回路压力,压力仍然停留在10MPa以上,存在很大高压熔堆的风险.增加一列卸压阀可把一回路压力降低到3MPa左右,安注系统得以投入,及时有效地阻止堆芯熔化进程,降低了高压熔堆风险.分析结果还显示高压安注系统的投入对一回路卸压具有重要影响.     

增强IVR有效性的堆内注水策略研究

熔融物堆内滞留（IVR）是一项核电厂重要的严重事故管理措施,通过将熔融物滞留在压力容器内,以保证压力容器完整性,并防止某些可能危及安全壳完整性的堆外现象。对于高功率和熔池中金属量相对不足的反应堆,若下封头形成3层熔池结构,则其顶部薄金属层导致的聚焦效应可能对压力容器完整性带来更大的威胁。本文考虑通过破口倒灌及其他工程措施实现严重事故下熔池顶部水冷却,建立熔池传热模型,分析顶部注水的带热能力,建立事件树,分析顶部注水措施的成功概率及IVR的有效性。结果表明,通过压力容器内外同时水冷熔融物,能显著增强IVR措施的有效性。     

非能动堆芯冷却系统LOCA下冷却能力分析

本文基于机理性分析程序建立了包括反应堆一回路冷却剂系统、专设安全设施及相关二次侧管道系统的先进压水堆分析模型,对典型的小破口失水事故和大破口失水事故开展了全面分析。针对不同破口尺寸、破口位置的失水事故,分析了非能动堆芯冷却系统（PXS）中非能动余热排出系统（PRHRS）、堆芯补水箱（CMT）、安注箱（ACC）、自动卸压系统（ADS）和安全壳内置换料水箱（IRWST）等关键系统的堆芯注水能力和冷却效果。研究表明,虽然破口尺寸、破口位置会影响事故进程发展,但所有事故过程中燃料包壳表面峰值温度不超过1 477 K,且反应堆堆芯处于有效淹没状态。PXS能有效排出堆芯衰变热,将反应堆引导到安全停堆状态,防止事故向严重事故发展。     

严重事故下正常余热排出系统向堆芯注水策略分析

选取导致堆芯熔化频率最高的始发严重事故--直接注入（DVI）管线断裂事故,以及典型高压熔堆事故--丧失主给水始发事故(LOFW),利用MAAP4程序,分析反应堆堆芯热工水力行为,并对正常余热排出系统（RNS）堆芯注水策略的有效性与负面效应进行评估。分析结果表明,在DVI管线断裂事故和LOFW严重事故序列中,利用RNS进行堆芯注水可有效终止堆芯熔化进程,维持堆芯长期冷却。但堆芯再淹没会产生更多的氢气,存在增加安全壳氢气燃烧风险的可能性。此外通过分析利用严重事故管理导则中辅助计算文件给出的堆芯最小流量实施堆芯注水策略,讨论注水流量对堆芯冷却的影响,结果表明,在实施堆芯注水策略时,建议在系统允许的情况下采用更高的流速进行堆芯冷却。     

压水堆核电站全厂断电事故及辅助给水系统的缓解能力研究

以美国surry核电站为参考对象,采用最佳估算程序SCDAP/RELAP5/MOD3.4,建立了一个典型的三环路压水堆核电站严重事故计算模型,对全厂断电(SBO)事故的物理现象及堆芯熔化进程进行了详细分析,并研究了全厂断电事故发生后辅助给水(AFW)分别持续1800s和3600s对事故的缓解效果.计算结果显示,辅助给水能有效地延缓堆芯熔化进程,大大推迟反应堆压力容器的失效时间,为操纵员恢复交流电源以及实施其它缓解措施赢得更多的时间.     

压水堆严重事故下封头热斑计算

压水堆堆芯熔化事故情况下,下封头热斑会造成压力容器局部过热,导致临界热流密度发生。利用FLUENT软件对堆芯熔化事故时的下封头热斑进行计算,从流动和换热角度预测热斑导致的下封头薄弱环节。计算结果表明:堆芯熔化事故时,压力容器下封头存在两处最薄弱的位置,分别为下封头正下方正对外部冷却水位置和氧化壳与压力容器交界处。特别是在氧化壳与压力容器交界处,由于多种原因导致临界热流密度发生,使得该处熔化严重。通过设置延伸小管和附加冷却水可延迟压力容器壁面熔穿的时间。     

A simple novel analysis procedure for IVR calculation in core-molten severe accident

In-Vessel Retention (IVR) of core melt is a key severe accident management strategy adopted by operating nuclear power plants and advanced light water reactors (ALWRs), AP600, AP1000, etc. External Reactor Vessel Cooling (ERVC), which involves flooding the reactor cavity to submerge the reactor vessel in an attempt to cool core debris relocated to the vessel low head, is a novel severe accident management for IVR analysis. In present study, IVR analysis code in severe accident (IVRASA) has been proposed to evaluate the safety margin of IVR in AP600 with anticipative depressurization and reactor cavity flooding in severe accident. For, IVRASA, a simple novel analysis procedure has been developed for modeling the steady-state endpoint of core melt configurations. Furthermore, IVRASA was developed in a more general fashion so that it is applicable to compute various molten configurations such as UCSB Final Bounding State (FIBS). The results by IVRASA were consistent with those of the UCSB and INEEL. Benchmark calculations of UCSB-assumed FIBS indicate the applicability and accuracy of IVRASA and it could be applied to predict the thermal response of various molten configurations.     

压水堆大破口失水事故引发的严重事故研究

采用机理性严重事故最佳估算程序SCDAP/RELAP5/MOD3.2，以美国西屋公司Surry核电站为参考对象，建立了1个典型的3环路压水堆核电站的严重事故分析模型，分别对主回路冷段和热段发生25cm大破口失水事故（LBLOCA）导致的堆芯熔化事故进行研究分析。结果表明，压水堆发生大破口失水事故时，堆芯熔化进程较快，大量堆芯材料熔化并坍塌至下腔室，反应堆压力容器下封头失效较早，且主回路冷段破口比热段破口更为严重。     

熔融物堆芯冷却滞留特性研究

The severe accident analysis model of the small modular reactor ACP100 is built using MELCOR code, and the core heat removed process through the barrel and wall of reactor pressure vessel (RPV) is analyzed by the cavity injection system (CIS). The collapse behavior of the fuel assemblies is estimated by the fuel rod degradation model, and the failure behavior of the lower core plate is estimated by ANSYS program. The results show that the fuel assemblies in the core center melt and collapse to form the core melting pool, while the structure of the fuel assemblies surrounding the core melting pool remains intact, and the core lower plate supports the core melting pool and un-collapsed fuel assemblies all the time, and no creep rupture phenomenon occurs; the core heat can be removed by CIS and the debris in-vessel retention successfully avoids the formation of molten pool in the lower head.     

MAAP5 simulation of the PWR severe accident induced by pressurizer safety valve stuck-open accident

The Modular Accident Analysis Program version 5 (MAAP5) is a computer code that can simulate the response of light water reactor power plants during severe accident sequences. The present work aims to simulate the severe accident of a typical Chinese pressure water reactor (PWR) with MAAP5. The pressurizer safety valve stuck-open accident is essentially a small break loss-of-coolant accident (SBLOCA), which becomes one of the major concerns on core melt initiating events of the PWR. Six cases with different assumptions in the pressurizer (PZR) safety valves (SVs) stuck-open accident stuck open accident were analyzed for comparison. The results of first three cases show that the severe accident sequence is correlated with the number of the stuck open valve. The primary system depressurized faster in a more SVs stuck open case, and the consequences in which is hence slighter. The remaining 3 cases along with the case 2 were then analyzed to study the effect of operator intervention to the accident. The results show that the auxiliary feed water (AFW) is effective to delay the core degradation and hence delayed the finally system recovery. The high pressure injection (HPI) operation and manually opening the steam generator (SG) SVs are effective to mitigate this kind of severe accident. The results are meaningful and significant for comprehending the detailed process of PWR severe accident, which is the basic standard for establishing the severe accident management guidelines.     

压水堆一回路卸压措施影响因素研究

研究压水堆一回路管道小小破口失水事故叠加辅助给水失效导致的高压堆芯熔化严重事故进程，对比验证不同严重事故缓解措施入口温度条件下一回路卸压缓解途径的充分性和有效性，并确认较佳的一回路冷却系统（RCS）降压途径。结果显示，以低于650℃的温度作为降压缓解措施入口条件，可及时恢复可能的堆芯冷却能力。一、二回路卸压效果分析表明，考虑了长期衰变热移出注水流量和堆芯过冷度要求，较佳的卸压配置为初期打开一列稳压器卸压阀，同时迅速恢复辅助给水并开启蒸汽发生器卸压阀。      

大亚湾核电站全厂断电诱发的严重事故过程研究

在大亚湾核电站严重事故计算分析结果的基础上,对全厂断电诱发的典型的严重事故序列及缓解对策进行了分析。结果表明,全厂断电事故发生后,大约1～2h堆芯上部会裸露,压力容器在5～7h后失效。在约100h安全壳超压失效,而堆坑地基在事故后8.7d会被熔蚀5.5m。结果还表明,堆坑注水措施可以防止堆坑地基熔穿并且减少事故中由于堆芯熔融物与混凝土反应产生的氢气。     

百万千瓦级压水堆严重事故后再注水的有效性评价

根据现有的设计资料,使用一体化严重事故分析程序MELCOR1.8.6建立了核电厂一、二回路系统,非能动堆芯冷却系统和安全壳系统的模型,并模拟冷段2英寸(5.08cm)小破口叠加重力注入失效的严重事故发生后,将冷却剂注入堆芯的情形,分析其对严重事故进程的缓解能力。本文选取3个严重事故的不同阶段,将冷却剂分别以小流量(10kg/s)、中流量(50kg/s)和大流量(200kg/s)的速率注入堆芯,通过比较氢气产生量、堆芯放射性产生量及堆芯温度等数据来评估在严重事故不同阶段再注水的可行性。结果表明:在堆芯损伤初期,可认为10kg/s以上的流量足以冷却百万千瓦级事故安全。而当严重事故发展到堆芯开始坍塌阶段,200kg/s的注水流量可认为是基本可行的,而小于此流量的注水应慎重考虑。     

Simulation of the small modular reactor severe accident scenario response to SBO using MELCOR code

Advanced small modular reactors (SMRs) use different design in the systems, structures, components from large reactors for achieving a high level of safety and reliability. In present work, the SMRs severe accident caused by the station blackout (SBO) was modeled and analyzed using MELCOR code, and the simulation of the accident scenario response to SBO was conducted. Based on the steady state calculation, which agrees well with designed values, we introduced the SBO accident for transient calculation. First, the case of the SBO accident without the passive core cooling system (PXS) was calculated. The progression and scenario in the reactor pressure vessel (RPV) and the containment were simulated and analyzed, including the transient response, cooling capacity and thermal-hydraulic characteristics and so on. The station black-out transient in the SMR can be simulated accurately, and the main failure model in the accident process can be concluded. Then three other cases of the SBO accident with different passive safety systems (core makeup tank (CMT), accumulator (ACC), passive residual heat removal system heat exchanger (PRHR HX), automatic depressurization system (ADS)) of the PXS were calculated respectively, and the results for different passive safety systems were compared. The passive core cooling system can not only provide water to the primary coolant system, but also take away the reactor decay residual heat. So in a station black-out transient, we can get more time for restoring AC power, and effectively prevent the accidents such as Fukushima.     

压水堆核电厂严重事故下堆腔注水措施研究

针对百万千瓦级压水堆核电厂,采用一体化严重事故分析工具,对一回路冷段大破口冷却剂丧失（LB-LOCA）始发严重事故下,采取堆腔注水（ERVC）缓解措施的事故进程进行模拟,对该措施缓解堆芯熔化进程、保持压力容器完整性的有效性进行分析验证,并对影响该措施的因素进行研究。分析结果表明,在充足的水源条件下,保证一定的注水速率和水位高度,LB-LOCA始发严重事故下采取堆腔注水的缓解措施可为下封头提供有效的冷却,保持压力容器的完整性。     

Formation, characterisation and cooling of debris: Scenario discussion with emphasis on TMI-2

Regarding safety improvements for existing nuclear power plants, the TMI-2 accident is interesting because of the present commercial dominance of light water reactors (LWR). This accident demonstrated that the nuclear safety philosophy evolved over the years has to cover accident sequences involving massive core melt progression in order to develop reliable mitigation strategies for both, existing and advanced reactors. Although the TMI-2 core was reflooded, the results also appear applicable to the general melt progression phenomenology of most unrecovered (unreflooded) blocked core accident scenarios. Nevertheless, a large range in the initial conditions of core melt progression provides significant uncertainties in assessing the integrity of the lower head, the containment in severe reactor accidents, and the consequences of recovery actions in accident management, as well as core reflooding in particular. The probability of success of reflooding as an accident management strategy – in-vessel reflooding to terminate the accident and ex-vessel flooding to prevent reactor vessel melt-through – has to be assessed and discussed in detail.     

小型压水堆完全丧失电源引发的严重事故研究

以压水堆严重事故最佳估算程序RELAP/SCDAPSIM/MOD3.4为核心软件,以假想的小型压水堆为研究对象,建立了1个径向3通道、轴向10节块的核反应堆严重事故计算模型,研究了完全丧失电源初因事件引发的严重事故过程,并对事故停堆后蒸汽发生器给水持续300s的缓解措施进行了分析。计算结果表明：蒸汽发生器辅助给水对于延迟事故进程,缓解事故后果具有重要作用。