Long-term stabilized millimeter-wave generation using a high-powermode-locked laser diode module

In this paper, a 60-GHz-band millimeter-wave (mm-wave) signal generation using a new 60-GHz mode-locked laser diode (MLLD) module stabilized by an optical injection will be presented. To modularize the MLLD, the precise position alignments and the fine tuning for the repetition rate is released; moreover, the output optical power of more than 6.0 dBm and the stability over nearly 1500 h are obtained. It is experimentally confirmed that the frequency and power stabilities are several tens of hertz and less than 1 dBm, respectively. The generated 60-GHz-band mm-wave signal with the 3-dB linewidth of less than 300 Hz over a 100-km-long optical fiber link is also successfully demonstrated     

采用单个相位调制器产生毫米波

实验研究了采用单个相位调制器(PM)产生毫米波的方案。该方案采用电混频器将射频(RF)信号与基带信号混频后再利用相位调制器产生双边带调制(DSB)信号,经光纤传输到基站后用一个光交叉复用器(IL)分离一阶边带和中心载波,一阶边带经过光电(O/E)检测器拍频产生两倍频于射频频率的毫米波,而中心载波可以作为上行链路载波重新利用。理论分析了该毫米波的传输性能,研究发现由于色散导致两个一阶边带时延不同,码元的占空比会随着传输距离的增加而减小,将限制毫米波的最大传输距离;实验中采用频率为20 GHz射频信号产生频率为40 GHz的毫米波,速率为2.5 Gbit/s的非归零(NRZ)码作为下行链路数据,经过20 km色散光纤传输后下行链路的功率代价为0.2 dBm。     

60 GHz OCS mm-wave generation for ROF system based on saturated parametric amplification effect in HNLF

A novel approach to generate 60 GHz optical carrier suppression (OCS) millimeter-wave (mm-wave) signal based on the saturated optical parametric amplification (OPA) effect in high non-linear fiber (HNLF) is investigated. In the proposed system, the OPA effect occurs when the signal and pump with 30 GHz frequency interval are set into the high non-linear fiber. By controlling the length of HNLF, OPA effect saturates, and the pump power is delivered in a large extent to the signal and idler light, so a 60 GHz OCS mm-wave is generated. The system does not need high-speed external modulator, high-frequency vibration source or narrow-band filter, which greatly reduces the cost and improves the stability of the radio over fiber (ROF) system. Results show that the 10 Gb/s downstream signal can be transmitted with negligible power penalty.     

Optical generation and distribution of continuously tunable millimeter-wave signals using an optical phase modulator

In this paper, we propose an approach to generate and distribute two wide bands of continuously tunable millimeter-wave (mm-wave) signals using an optical phase modulator and a fixed optical notch filter. We demonstrate theoretically that the odd-order electrical harmonics are cancelled and even-order electrical harmonics are generated at the output of a photodetector when the optical carrier is filtered out from the phase-modulated optical spectrum. Analysis shows that dispersion compensation is required in order to maintain the suppression of the odd-order electrical harmonics, in order to eliminate signal fading of the generated electrical signal when the optical signal is distributed using conventional single-mode optical fiber. It is experimentally demonstrated that, when the electrical drive signal is tuned from 18.8-25 GHz, two bands of mm-wave signals from 37.6 to 50 GHz and from 75.2 to 100 GHz with high signal quality are generated locally and remotely. This approach does not suffer from the direct current (dc) bias-drifting problem observed when an optical intensity modulator is used.     

基于级联马赫-曾德电光调制器的60GHz光载毫米波传输系统的研究

提出并实现了一种新的产生毫米波的六倍频技术。采用两个相同的串联马赫一曾德电光调制器（MZM）,调节第1个MZM调制器的偏置电压使其工作在最小传输模式,只输出奇次光谐波分量;调节第2个MZM调制器的偏置电压使其工作在最大传输模式,抑制所有的奇次光谐波分量。实验显示,采用10GHz的射频（RF）信号驱动这两台MZM调制器后...     

Recovery of 80 GHz optical clock from 160 Gbit/s data using regeneratively modelocked laser diode

An 80 GHz optical clock signal was successfully recovered from a 160 Gbit/s data stream using a regeneratively modelocking scheme of a semiconductor modelocked laser (MLLD). To handle an 80 GHz electrical signal, the MLLD integrated with a high-mesa electroabsorption modulator and a W-band UTC-PD module are used in this scheme.     

Transmission Performance of the Optical Millimeter-wave Up-conversion Link Using a Phase Modulator

Numerically analyzed is the transmission performance of the optical millimeter(mm)-wave generated by frequency up-conversion via a phase modulator along the dispersive fiber.60 GHz mm-wave sub-carrier(SC)signals can be obtained after fiber transmission,simultaneously,the phase-modulated signals can be converted to the intensity-modulated ones.The numerical results show that the optical mm-wave at fading loops has better performance,and the eye diagram still keeps open when optical mm-wave signal is transmit...     

Multiple-frequency basestation RoF system based on polarization multiplexed FWM in SOA

An approach of multiple-frequency millimeter-wave(mm-wave)signal generation is proposed for radio-over-fiber(RoF)system with multiple-frequency basestations(MFBSs).Two groups of orthogonally polarized signals are injected into a semiconductor optical amplifier(SOA),and subsequently ten new different wavelengths are generated via four-wave mix-ing(FWM)effect.At each MFBS,different wavelengths are filtered out using demultiplexer and then input to a photodiode(PD)to generate the mm-wave signals with the frequencies from 52 GHz to 68 GHz at the interval of 2 GHz.Simulation results verify that the proposed multiple-frequency generation for MFBS RoF system can work properly.     

基于相位调制器倍频技术产生56GHz毫米波的光载无线通信系统

提出并实验研究了一种基于光相位调制器(PM)倍频技术产生56GHz毫米波的光载无线通信(RoF)系统。在中心站,通过28GHz射频(RF)信号驱动PM产生了56GHz光毫米波,并将下行的2.8Gb/s开关键控(OOK)信号调制到该光载波上,然后经过20km标准单模光纤(SSMF)传输至基站,最后由天线进行发射。用户终端接收后,采用相干解调恢复出基带信号。实验结果表明,56GHz光载毫米波信号经SSMF传输20km后其功率代价小于1dB,通过无线方式传输1.1m后其功率代价小于2.5dB。     

A novel scheme to implement duplex 60-GHz radio-over-fiber link with 20-GHz double-sideband optical millimeter-wave transmitted along the fiber

A duplex radio-over-fiber (RoF) link with a novel scheme to generate 60-GHz millimeter (mm)-wave using 20 GHz double sideband (DSB) optical mm-wave with signal carried only by its optical carrier is investigated. In the RoF downlink, the modulation frequency to generate the DSB optical mm-wave is reduced greatly. The theoretical analysis and numerical simulation show that this scheme cannot only eliminate the code form distortion caused by the time shifting of the sidebands, but also reduce the influence of the fading effect as the DSB optical mm-wave signal is transmitted along the fiber. Based on the scheme, the duplex RoF link with the frequency up- (down-) conversion of the down- (up-) link mm-wave signal is built and the uplink transmission performance is analyzed theoretically.     

基于直流光注入直调DFB-LD的可调光毫米波信号产生技术

提出了一种基于直流光注入直接调制分布反馈式半导体激光器(DFB-LD)的载波可调的光毫米波生成方案,利用直接调制DFB-LD的输出瞬态波长随驱动电流增大而蓝移的特点,将直流光注入至直调DFB-LD的0码波长附近注入锁定。锁定的直调激光器在1码时输出的蓝移波长与原注入波长相位相干,再通过光电探测器将拍频信号转换为调制的光毫米波信号。实验重点讨论了40GHz光毫米波的产生,同时完成了30、40、50和60GHz光毫米波的可调谐性实验。本文的方案结构简单,无需外调制器和微波本振,载波可调并可产生高至60GHz光毫米波信号,可作为光/无线混合接入中成本节省的光上变频方案。     

60GHz全双工OFDM-ROF系统的实验研究

研究了基于光外部调制的方式产生60GHz光毫米波的全双工光纤无线(ROF)通信系统。实验利用29GHzRF源产生58GHz的光载毫米波,2.5Gbit/s OFDM信号作为下行数据信号调制到光载毫米波上并传输光纤20km,在基站与用户单元实现3.3m的无线传输。同时实现了下行信号中心载波重利用作为上行信号的光载波,2.5Gbit/s的OOK信号作为上行数据信号调制到光载波上经20km上行链路光纤传输至中心站。     

Cancellation of the signal fading for 60 GHz subcarrier multiplexedoptical DSB signal transmission in nondispersion shifted fiber usingmidway optical phase conjugation

In millimeter-wave (mm-wave) optical double sideband (DSB) signal transmission systems, the received radio frequency (RF) power fades periodically because of the group velocity dispersion (GVD) and the self-phase modulation (SPM) of optical fibers. In this paper, cancellation of the signal fading by using midway optical phase conjugation in mm-wave subcarrier multiplexed (SCM) optical DSB signal is analyzed. Fading-free 60 GHz mm-wave optical DSB signal transmission over 100 km-long nondispersion shifted single-mode fiber at 1550 nm by using a semiconductor optical amplifier (SOA) optical phase conjugator (OPC) in the midway of optical link is experimentally demonstrated for the first time. Finally, the degradation factor of the OPC system is also discussed     

Optical mm-Wave Signal Generation by Frequency Quadrupling Using an Optical Modulator and a Silicon Microresonator Filter

By adjusting the direct current (dc) bias on an electrooptic modulator to suppress the first-order sideband and subsequently using a double-waveguide micro-ring resonator to filter out the optical carrier, millimeter (mm)-wave signal was generated at a frequency of four times the 10-GHz local oscillator. A monolithic integrated silicon-based optical mm-wave signal generator by frequency quadrupling is proposed. A silicon integrated microresonator filter was fabricated and its design parameters are given. High extinction ratio optical mm-wave signal was obtained. The single sideband noise spectrum of the generated 40-GHz optical signal was measured, showing similar performance when compared with that generated by a radio-frequency synthesizer.      

Highly stabilized millimeter-wave generation by using fiber-opticfrequency-tunable comb generator

A novel optical generation and transport technique for millimeter-wave (mm-wave) signals by using the fiber-optic frequency-tunable comb generator having a discrete emission spectrum as the light source is proposed. 60 GHz mm-wave signal generation and transmission over a 108 km-long optical fiber link at λ=1560 nm is demonstrated. Excellent stability of both the frequency and amplitude of the mm-wave carrier is attained, so that the 3 dB linewidth is less than 0.3 kHz and the variance of the amplitude fluctuation is 0.07 dB. The advantages include tunability of the carrier frequency, handling ease, and no need for a high-speed external light modulator     

Generation and Modulation of Tunable mm-Wave Optical Signals Using Semiconductor Ring Laser

Optical injection locking and cavity enhanced four-wave mixing in semiconductor ring lasers have been used to generate data modulated millimeter (mm)-wave optical signals. The scheme is shown to have multigigahertz (multi-GHz) modulation bandwidth. The 4-Gb/s data is transferred directly from an intensity modulated optical signal onto an mm-wave optical signal with the mm-wave frequency tunable in steps of 62.5 GHz and with flexible radio-frequency modulation formats over the optical carrier. Bit-error-rate and eye-diagram measurements confirm excellent signal quality.      

On Frequency-Doubled Optical Millimeter-Wave Generation Technique Without Carrier Suppression for In-Building Wireless Over Fiber Applications

A novel optical millimeter-wave (mm-wave) generation scheme based on double-sideband phase modulation (DSB-PM) to achieve frequency doubling without suppressing the carrier is proposed. Theoretical analysis shows that the generated 60-GHz optical mm-wave can tolerant ${pm}$ 0.016-nm wavelength drifting with filter bandwidth ranging from 70 to 100 GHz to sustain first to second harmonic suppression ratio of 18 dB. In addition, error-free transmission of 60-GHz mm-wave at 2.5 Gb/s is experimentally demonstrated over a combined distance of 3-m wireless with 21-dBm equivalent isotropically radiated power, and 250-m fiber to best emulate an in-building network environment. Dispersion effect on the frequency-doubled PM optical mm-wave without carrier suppression is also analyzed and experimentally studied by comparing the link performance over single-mode fiber (SMF-28) and dispersion-shifted fiber (DSF), respectively.      

New progress of mm-wave radio-over-fiber system based on OFM

This paper presents an overview on new progresses-of millimeter wave (mm-wave) radio-over-fiber (RoF) system based on mm-wave generation by optical frequency multiplication (OFM), including gen-eration of high-order optical side modes by optical modulation using dual-drive Mach-Zehnder modulator (DD-MZM) and enhancement of high-order optical side mode induced by selective amplification due to stimulated Brillouin scattering (SBS). The paper describes OFM by using DD-MZM in principle and verifies it in an experimental bidirectional 40GHz RoF system. SBS amplification enhances the generated information-bearing mm-wave in downlink and also helps in producing a pure reference mm-wave for radio frequency-intermediate frequency (RF-IF) down-conversion in uplink. These efforts pushed the OFM technology of mm-RoF systems to achieve more and more feasibility and cost-effectiveness.     

Fiber-optic millimeter-wave downlink system using 60 GHz-bandexternal modulation

In this paper, a fiber-optic millimeter-wave (mm-wave) downlink system using 60 GHz-band external modulation is investigated. We prepare the fiber-optic 60 GHz-band mm-wave downlink testbed. It consists of an optical modulation section with a mm-wave signal generator, an optical single sideband (SSB) filter, a standard single-mode fiber (SMF), an optical detection section with a 60 GHz-band radio transmitter and a 60 GHz-band radio receiver. To modulate the laser output with 60 GHz-band mm-wave signals directly, a specially designed electro-absorption modulator with high-efficiency at around 60 GHz is used. The use of this modulator makes the simpler system configuration possible. Using the downlink testbed, the 5 m-long free-space propagation of subcarrier multiplexed 156 Mb/s-DPSK 60 GHz-band mm-wave signals recovered by optical direct detection is successfully demonstrated. The transmission of the mm-wave signals over 85 km-long standard SMF is also successfully demonstrated, using an optical SSB filtering technique to overcome the fiber dispersion. The BER of 10^-9 is achievable at the optical received power of -7.0 dBm     

Millimeter-wave broad-band fiber-wireless system incorporating baseband data transmission over fiber and remote LO delivery

We present the first demonstration of a millimeter-wave (mm-wave) broadband fiber-wireless system which incorporates baseband data transmission in both the downstream (622 Mb/s) and upstream (155 Mb/s) directions. The local oscillator (LO) required at the remote antenna base station for up- and downconversion to/from the mm-wave radio frequency (RF) is delivered remotely via a modulation scheme that is tolerant to the effects of fiber chromatic dispersion on the detected LO carrier power. The technique employs a single dual electrode modulator located at the central office (CO) and the data and an RF signal at a frequency equal to half the LO frequency, are applied simultaneously to the device. The modulation scheme was optimized as a function of the modulator operating conditions. Simultaneous bidirectional radio transmission in the mm-wave fiber-wireless network was implemented using specially designed mm-wave diplexers located at the base station (BS) and customer unit, and a single Ka-band printed antenna array at the BS operating simultaneously in transmit and receive mode. Error-free data transmission was demonstrated for both down(34.8 GHz) and uplinks (37.5 GHz) after 20 km of single-mode optical fiber and a bit error rate (BER) of 10/sup -6/ was achieved after the inclusion of a 2-m radio link.