Y2O3和纳米AlN协同作用对氮化铝陶瓷烧结性能及热传导的影响

在微米氮化铝粉体中添加含量为4%的Y2O3和不同含量的纳米AlN粉体制备氮化铝陶瓷,研究了Y2O3和纳米AlN协同作用对微米氮化铝陶瓷烧结性能和热传导性能的影响。结果表明,Y2O3优先与纳米AlN粉体表面的Al2O3反应生成活性较高的第二相Al5Y3O12,相比于Y2O3与微米AlN粉体表面Al2O3反应生成的Al5Y3O12,具有更低的熔化温度及更好的流动性;同时,纳米AlN粉体的高比表面能也促进氮化铝陶瓷的致密化进程。二者的协同作用有效地促进氮化铝陶瓷的致密烧结,改善第二相的微观分布,从而能在较低的烧结温度下获得具有较高热导率的氮化铝陶瓷。当Y2O3和纳米AlN粉体的添加量(质量分数)分别为4%和1.5%时,在1800℃烧结得到的氮化铝陶瓷密度为3.26 g·cm-3,第二相以连续相的形式分布于氮化铝晶界处,热导率为151.75 W/(m.K)。     

Li2O对SPS烧结AlN陶瓷致密化、显微结构和导热性的影响

研究了低温烧结助剂Li2O对SPS烧结AlN陶瓷烧结致密化过程、烧结体显微结构和导热性的影响.研究表明:在SPS烧结过程中,烧结助剂Li2O和Sm2O3(或Y2O3)的加入使AlN试样开始收缩并进入烧结初期阶段的温度从1550℃左右下降到1200℃以下;同时Li2O使AlN试样的烧结温度显著降低,完全致密化温度降低到1650℃左右.烧结体的显微结构表明:Li2O的加入有助于形成润湿性良好的液相,促进AlN陶瓷的液相烧结;但不利于快速烧结坯体中气体的扩散与逸出,使试样的致密度受到影响.同时,Li2O影响AlN晶粒的发育,使液相润湿性提高,晶界相均匀分布,增加了晶粒界面上的声子散射,对AlN材料的热导率产生不利影响.同时,添加1.0wt%Li2O和1.5wt%Sm2O3的AlN试样的热导率低于仅添加1.5wt%Sm2O3的试样.     

晶界相和晶界对AlN陶瓷热导率的影响

本文研究了掺杂CaO Y2 O3热压烧结和常压烧结AlN陶瓷的晶界相及其产生过程和除氧机制 ;分析了两种烧结工艺烧制的AlN陶瓷的晶界成份 ;测定了不同晶界相含量和晶界成份对应的AlN陶瓷的热导率     

热压烧结AlN(Y_2O_3)陶瓷热导率的温度关系

采用热压烧结技术,以Y2O3为烧结助剂制备AlN陶瓷。闪光法测试AlN陶瓷在室温~200℃的温度关系。结果表明,AlN陶瓷热导率随温度升高而降低;气孔对AlN陶瓷热导率随温度变化的速率有抑制作用,气孔率越小(致密度越高),热导率对温度变化越敏感;AlN陶瓷钇铝酸盐晶界相含量对热导率随温度变化的速率有促进作用,钇铝酸盐含量越高,热导率对温度变化越敏感。     

空心阴极等离子烧结AlN陶瓷

将空心阴极效应运用于AlN陶瓷的烧结,选用自蔓延高温合成的AlN粉体为原料,用Y2O3-CaO-Li2O作为烧结助剂,制备出了致密度高,导热性能好的AlN陶瓷.在添加5.5wt％的Y2O3-CaO-Li2O(Y2O3:Li2O:CaO=44:6:5wt％)作为烧结助剂,在1700℃,保温3h的烧结条件下,获得相对密度为98.89％,热导率为93.8 W/(m·K)AlN烧结体.烧结体的断口SEM照片显示烧结试样的晶粒生长发育完善,晶粒轮廓清晰呈尖锐的多面体形状,晶粒大小均匀,气孔和晶界相少,断裂模式为穿晶断裂.TEM表明:晶界相少,且大部分都缩至三角晶界,AlN颗粒与颗粒接触紧密.     

晶界相和晶界对AlN陶瓷热导率的影响

本文研究了掺杂CaO-Y2O3热压烧结和常压烧结AlN陶瓷的晶界相及其产生过程和除氧机制；分析了峡谷种烧结工艺烧制的AlN陶瓷的晶界成份测定不同晶界相含量和晶界成份对应的AlN陶瓷的热导率。     

无压烧结制备高致密度AlN-BN复合陶瓷

以低温燃烧合成前驱物制备的比表面积为17.4m²/g的AlN粉末和市售BN粉末为原料, 利用无压烧结工艺制备AlN-15BN复合陶瓷, 研究了复合陶瓷的烧结行为以及制备材料的性能, 结果表明: 由于AlN粉末的烧结活性好, 复合材料的烧结致密化温度主要集中在1500～1650℃之间, 在1650℃烧结后, AlN-15BN复合陶瓷的相对密度可达95.6%. 继续升高烧结温度, 材料的致密度变化不大, 热导率继续增加. 在1850℃烧结3h后, 可以制备出相对密度为96.1%, 热导率为132.6W·m^-1·K^-1, 硬度为HRA64.2的AlN-15BN复合陶瓷. 提出了高比表面积的AlN粉末促进复合陶瓷烧结的机理, 利用XRD, SEM等手段对烧结体进行了表征.     

AlN/CNT吸波陶瓷的制备及性能研究

研究了AlN/CNT复相陶瓷的致密化、热传导和介电性能,结果表明,采用SPS能够降低材料的烧结难度,促进AlN晶粒充分长大和氧杂质的去除,改善热导率,在Ka波段(26.5-40.0GHz),介电常数实部与烧结温度无关,虚部则由于高温烧结导致CNT结构坍塌而下降,适当的CNT量和烧结温度能够兼顾介电损耗、高热导率以及适中的介电常数。     

放电等离子烧结制备透明AlN陶瓷

采用放电等离子烧结(spark plasma sintering,SPS)技术,添加不同含量CaF2为烧结助剂,成功制备了透明氮化铝(AlN)陶瓷.SPS技术具有烧结快速,烧结体致密度高的特点,是制备透明AlN的有效方法.CaF2的加入量的提高,有利于烧结体的致密度和透过率的提高.当CaF2加入量为3%(质量分数)时,烧结体致密度不再继续提高,但仍有利于透过率的提高,此时烧结体透过率最高为54.7%.SEM、XRD、TEM和EDX结果表明烧结体具有很高的致密度、纯度,均匀的晶粒形状和尺寸,晶界及三角晶界处观察不到第二相的存在,从而保证了烧结体良好的光学性能.     

纳米复合助剂对氮化铝陶瓷烧结特性的影响

如何获得理想的氮化铝陶瓷是电子陶瓷材料研究领域的重要课题。本研究采用纳米复合添加剂Y2O3-La2O3,分别在1600℃、1650℃、1700℃、1750℃和1800℃下,无压烧结氮化铝陶瓷。测定并分析了AlN陶瓷的性能和微观结构。实验结果表明:烧结温度达到1750℃,就可获得致密烧结,此时AlN晶粒细小均匀,第二相Al2Y4O9、LaAlO3和Y2O3分布在AlN晶界,AlN晶粒内的氧含量很低,AlN陶瓷样品的热扩散率较高。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...