Synthesis and properties of lanthanum hexaaluminate ceramic La1−xCaxAl11−y−zMgyTizO18

The aim of the present work is to obtain ceramic materials with a hexagonal structure and high density, hardness and mechanical strength at lower synthesis temperature. Ceramic samples with nominal composition La_1−xCa_xAl_11−y−zMg_yTi_zO₁₈ (x=0–1; y=0–3; z=0–3,5) are prepared. The samples are sintered at temperature 1500 °C by one-stage and two-stage ceramic technology. By X-ray diffraction and scanning electron microscopy, predominant phase LaAl₁₁O₁₈ and second phases LaAlO₃ and -Al₂O₃ are identified. Ceramic materials are characterized with high physico-mechanical properties and may be find application for production of mill bodies and materials for immobilization of nuclear waste.     

TayNb1−yVO5 (0<y<1) mixed oxides synthesized by sol–gel method: electrochemical Li-insertion

Mixed oxides of general formulae Ta_yNb_1−yO₅ (0<y<1) have been synthesized by a modified sol–gel method. Characterization of the samples has been carried out by x-ray diffraction, SEM/EDX, FTIR spectroscopy and thermal analysis. The electrochemical properties have been studied in a lithium cell. The first discharge capacity decrease from 206 (y=0.25) to 136 mA h g⁻¹ (y=0.75). Ta_yNb_1−yO₅ samples undergo an irreversible structural changes induced by electrochemical Li⁺-insertion. For all compositions, the new compounds formed after the first discharge has a very high cyclability, as shown the low capacity loss <1% per cycle.     

AFeO3 (A=La, Nd, Sm) and LaFe1−xMgxO3 perovskites as methane combustion and CO oxidation catalysts: structural, redox and catalytic properties

Catalytic methane combustion and CO oxidation were investigated over AFeO₃ (A=La, Nd, Sm) and LaFe_1−xMg_xO₃ (x=0.1, 0.2, 0.3, 0.4, 0.5) perovskites prepared by citrate method and calcined at 1073 K. The catalysts were characterized by X-ray diffraction (XRD). Redox properties and the content of Fe⁴⁺ were derived from temperature programmed reduction (TPR). Specific surface areas (SA) of perovskites were in 2.3–9.7 m² g⁻¹ range. XRD analysis showed that LaFeO₃, NdFeO₃, SmFeO₃ and LaFe_1−xMg_xO₃ (x·0.3) are single phase perovskite-type oxides. Traces of La₂O₃, in addition to the perovskite phase, were detected in the LaFe_1−xMg_xO₃ catalysts with x=0.4 and 0.5. TPR gave evidence of the presence in AFeO₃ of a very small fraction of Fe⁴⁺ which reduces to Fe³⁺. The fraction of Fe⁴⁺ in the LaFe_1−xMg_xO₃ samples increased with increasing magnesium content up to x=0.2, then it remained nearly constant. Catalytic activity tests showed that all samples gave methane and CO complete conversion with 100% selectivity to CO₂ below 973 and 773 K, respectively. For the AFeO₃ materials the order of activity towards methane combustion is La>Nd>Sm, whereas the activity, per unit SA, of the LaFe_1−xMg_xO₃ catalysts decreases with the amount of Mg at least for the catalysts showing a single perovskite phase (x=0.3). Concerning the CO oxidation, the order of activity for the AFeO₃ materials is Nd>La>Sm, while the activity (per unit SA) of the LaFe_1−xMg_xO₃ catalysts decreases at high magnesium content.     

Electrical resistivity and thermopower of (La1−xSrx)MnO3 and (La1−xSrx)CoO3 at elevated temperatures

Electrical resistivity and Seebeck (S) measurements were performed on (La_1−xSr_x)MnO₃ (0.02x0.50) and (La_1−xSr_x)CoO₃ (0x0.15) in air up to 1073 K. (La_1−xSr_x)MnO₃ (x0.35) showed a metal-to-semiconductor transition; the transition temperature almost linearly increased from 250 to 390 K with increasing Sr content. The semiconductor phase above the transition temperature showed negative values of S. (La_1−xSr_x)CoO₃ (0x0.10) showed a semiconductor-to-metal transition at 500 K. Dominant carriers were holes for the samples of x0.02 above room temperature. LaCoO₃ showed large negative values of S below ca. 400 K, indicative of the electron conduction in the semiconductor phase.     

Ce1−xCuxO2−x/Al2O3/FeCrAl catalysts for catalytic combustion of methane

A series of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts (x = 0–1) were prepared. The structure of the catalysts was characterized using XRD, SEM and H₂-TPR. The catalytic activity of the catalysts for the combustion of methane was evaluated. The results indicated that in the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts the surface phase structure were the Ce_1−xCu_xO_2−x solid solution, -Al₂O₃ and γ-Al₂O₃. The surface particle shape and size were different with the variety of the molar ratio of Ce to Cu in the Ce_1−xCu_xO_2−x solid solution. The Cu component of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts played an important role to the catalytic activity for the methane combustion. There were the stronger interaction among the Ce_1−xCu_xO_2−x solid solution and the Al₂O₃ washcoats and the FeCrAl support.     

Preparation and characterisation of SrTi1−x−yZrxMnyO3 solid solution powders in relation to their use in combustion catalysis

Mixed oxides with compositions SrTi_1−x−yZr_xMn_yO₃, with 0 ≤ x ≤ 1 and 0 ≤ y ≤ 0.2 have been prepared with a conventional coprecipitation method. Some of them are constituted by very pure perovskite-type solid solution phases, with tetravalent Zr and Mn substituting for Ti in the B site. The addition of Zr to SrTiO₃ tends to increase the surface areas, while the insertion of Mn tends to decrease it. Mn-containing materials are active in the catalytic combustion of 1% methane in air at temperatures higher than 700 K and can be competitive with pure manganite perovskites like LaMnO₃ in spite of the lower Mn content. Pyridine adsorption experiments show that medium strength Lewis acid sites are located at the surface of these materials, and could be involved in the hydrocarbon CH bond activation.     

Sintering behaviour of La1−xSrxFeO3−δ mixed conductors

The sintering properties of La_1−xSr_xFeO_3−δ (x = 0.1, 0.25) mixed conductors have been investigated with particular emphasis on the effect of secondary phases due to cation non-stoichiometry (±5 mol% La excess and deficiency). Secondary phases, located at grain boundaries in cation non-stoichiometric materials, increased the sintering temperature compared to single-phase materials. Extensive swelling in final stage of sintering was observed in all materials, which resulted in micro-porous materials. The swelling was most pronounced in the phase pure and two-phase materials due to La-deficiency, while refractory secondary phases in La-excess materials inhibited both sintering, grain growth and swelling. In La-deficient materials, formation of molten secondary phases resulted in rapid swelling due to viscous flow. The present findings demonstrated the importance of controlling sintering temperature and time, as well as careful control of the cation stoichiometry of La_1−xSr_xFeO_3−δ in order to achieve fully dense and homogenous La_1−xSr_xFeO_3−δ ceramics.     

Synthesis, characterization and catalytic activity for NO–CO reaction of Pd–(La, Sr)2MnO4 system

La_xSr_2−xMnO₄ (0 ≤ x ≤ 0.8) oxides were synthesized and single-phase K₂NiF₄-type oxides were obtained in the range of 0.1 ≤ x < 0.5. The catalytic activity of La_xSr_2−xMnO₄ for NO–CO reaction increased with increasing x in the range of solubility limit of La. La_0.5Sr_1.5MnO₄ showed the highest activity among La_xSr_2−xMnO₄ prepared in this study, but its activity was inferior to perovskite-type La_0.5Sr_0.5MnO₃. Among the Pd-loaded catalysts, however, Pd/La_0.8Sr_1.2MnO₄ showed the higher activity and the selectivity to N₂ than Pd/La_0.5Sr_0.5MnO₃ and Pd/γ-Al₂O₃. The excellent catalytic performance of Pd/La_0.2Sr_1.2MnO₄ could be ascribable to the formation of SrPd₃O₄ which was detected by XRD in the catalyst but not in the other two catalysts.     

Preparation of CexZr1−xO2 (x = 0.75, 0.62) solid solution and its application in Pd-only three-way catalysts

Nanoparticles of Ce_xZr_1−xO₂ (x = 0.75, 0.62) were prepared by the oxidation-coprecipitation method using H₂O₂ as an oxidant, and characterized by N₂ adsorption, XRD and H₂-TPR. Ce_xZr_1−xO₂ prepared had single fluorite cubic structure, good thermal stability and reduction property. With the increasing of Ce/Zr ratio, the surface area of Ce_xZr_1−xO₂ increased, but thermal stability of Ce_xZr_1−xO₂ decreased. The surface area of Ce_0.62Zr_0.38O₂ was 41.2 m²/g after calcination in air at 900 °C for 6 h. TPR results showed the formation of solid solution promoted the reduction of CeO₂, and the reduction properties of Ce_xZr_1−xO₂ were enhanced by the cycle of TPR-reoxidation. The Pd-only three-way catalysts (TWC) were prepared by the impregnation method, in which Ce_0.75Zr_0.25O₂ was used as the active washcoat and Pd loading was 0.7 g/L. In the test of Air/Fuel, the conversion of C₃H₈ was close to 100% and NO was completely converted at λ < 1.025. The high conversion of C₃H₈ was induced by the steam reform and dissociation adsorption reaction of C₃H₈. Pd-only catalyst using Ce_0.75Zr_0.25O₂ as active washcoat showed high light off activity, the reaction temperatures (T₅₀) of 50% conversion of CO, C₃H₈ and NO were 180, 200 and 205 °C, respectively. However, the conversions of C₃H₈ and NO showed oscillation with continuously increasing the reaction temperature. The presence of La₂O₃ in washcoat decreased the light off activity and suppressed the oscillation of C₃H₈ and NO conversion. After being aged at 900 °C for 4 h, the operation windows of catalysts shifted slightly to rich burn. The presence of La₂O₃ in active washcoat can enhance the thermal stability of catalyst significantly.     

Sintering and electrical conductivity in fast oxide ion conductors La2−xRxMo2−yWyO9 (R: Nd, Gd, Y)

Attrition and ball milling are used as mechanical means to reduce grain size of optimized fast oxide-ion conductors La_2−xR_xMo_2−yW_yO₉ (R: rare earths). Dilatometry is used to determine the optimal sintering conditions in order to obtain high density samples (greater than 96% of relative density) with help of scanning electron microscopy to characterize their microstructure. The optimal sintering temperatures are highly dependent on the chemical composition, and therefore identical annealing temperatures do not warrant similar relative densities. Complex impedance spectroscopy show that above the transition temperature of La₂Mo₂O₉ at 580 °C, the conductivity of all the studied compounds is lower than that of the parent compound, whereas just below the transition, in most cases the stabilization of the cubic phase increases conductivity. An interesting result is that tungsten substitution, which stabilizes La₂Mo₂O₉ against reduction, does not affect significantly the oxide ion conduction.     

Structure and microwave dielectric properties of Nd(2−x)/3LixTiO3

The structure evolution, and microwave dielectric properties of Nd_(2−x)/3Li_xTiO₃ ceramics (0 ≤ x ≤ 0.5) were investigated in this paper. X-ray diffraction (XRD) and scanning electron microscopy (SEM) results show that samples with x = 0.2–0.4 exhibit single phase. Multi-phases of Nd₂Ti₂O₇, Nd_2/3TiO₃ and Nd₂Ti₄O₁₁ were observed when x = 0 and 0.1. The concentration and ordering degree of A-site decrease with the increase of x value. The dielectric constant increases up to x = 0.2 and then decreases with the further increase of x value. The Qf value decreases with the increase of x value. The temperature coefficient of resonant frequency exhibits negative value and the absolute value decreases greatly with the decrease of x value.     

Effect of the method of obtaining Li2CO3---LiyNi1−yO mixtures on the densification of the resulting LixNi1−xO solid solutions

The weight and plaque diameter change following trermal treatment, and the density and lattice constant of lithium-rich Li_xNi_1−xO solid solutions obtained by heat treatment at 750°C of Li₂CO₃---Li_yNi_1−yO (y < x) mixtures were measured as a function of time. It was found that densification of the solid solutions depends on the method of obtaining the Li₂CO₃---Li_yNi_1−yO mixtures. When a large amount of carbonate is put into the starting mixtures Ni---Li₂CO₃-binder, and the powders are milled together, sintering occurs; in contrast, when the carbonate is added after the formation of Li_yNi_1−yO solid solution, so that the interstices of the plaque are filled with molten carbonate, the resulting mixtures exhibit no densification. For densification to occur, Li₂CO₃ must be in intimate contact with the lithium-doped NiO grains.     

Methane combustion and CO oxidation on LaAl1−xMnxO3 perovskite-type oxide solid solutions

Structural, redox and catalytic deep oxidation properties of LaAl_1−xMn_xO₃ (x=0.0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8, 1.0) solid solutions prepared by the citrate method and calcined at 1073 K were investigated. XRD analysis showed that all the LaAl_1−xMn_xO₃ samples are single phase perovskite-type solid solutions. Particle sizes and surface areas (SA) are in the 280–1180 Å and 4–33 m² g⁻¹ ranges, respectively. Redox properties and the content of Mn⁴⁺ were derived from temperature programmed reduction (TPR) with H₂. Two reduction steps are observed by TPR for pure LaMnO₃, the first attributed to the reduction of Mn⁴⁺ to Mn³⁺ and the second due to complete reduction of Mn³⁺ to Mn²⁺. The presence of Al in the LaAl_1−xMn_xO₃ solid solutions produces a strong promoting effect on the Mn⁴⁺→Mn³⁺ reducibility and inhibits the further reduction to Mn²⁺. Both for methane combustion and CO oxidation all Mn-containing perovskites are much more active than LaAlO₃, so pointing to the essential role of the transition metal ion in developing highly active catalysts. Partial dilution with Al appears to enhance the specific activity of Mn sites for methane combustion.     

Synthesis and properties of Bi0.5(Na1−x−yKxAgy)0.5TiO3 lead-free piezoelectric ceramics

Bi_0.5(Na_1−x−yK_xAg_y)_0.5TiO₃ piezoelectric ceramics were prepared by conventional ceramic processes. X-ray diffraction patterns show a pure perovskite structure, indicating that the K⁺ and Ag⁺ ions substitute for the Na⁺ ions in Bi_0.5Na_0.5TiO₃. The temperature dependence of the dielectric constant and dissipation factor shows all ceramics to experience two phase transitions: from ferroelectric to anti-ferroelectric and from anti-ferroelectric to paraelectric. The transition temperature from ferroelectric to anti-ferroelectric and the temperature at which the dielectric constant reaches its maximum value decrease with the increase of K⁺ amount. At room temperature, the ceramics containing 17.5–20 mol% K⁺ and 2 mol% Ag⁺ exhibit high piezoelectric constant (d₃₃ = 180 pC/N) and high electromechanical coupling factor (k_p = 35%).     

Superior performance of Ir-substituted hexaaluminate catalysts for N2O decomposition

Novel Ir-substituted hexaaluminate catalysts were developed for the first time and used for catalytic decomposition of high concentration of N₂O. The catalysts were prepared by one-pot precipitation and characterized by X-ray diffraction (XRD), N₂-adsorption, scanning electronic microscopy (SEM) and temperature-programmed reduction (H₂-TPR). The XRD results showed that only a limited amount of iridium was incorporated into the hexaaluminate lattice by substituting Al³⁺ to form BaIr_xFe_1−xAl₁₁O₁₉ after being calcined at 1200 °C, while the other part of iridium existed as IrO₂ phase. The activity tests for high concentration (30%, v/v) of N₂O decomposition demonstrated that the BaIr_xFe_1−xAl₁₁O₁₉ hexaaluminates exhibited much higher activities and stabilities than the Ir/Al₂O₃-1200, and the pre-reduction with H₂ was essential for activating the catalysts. By comparing BaIr_xFe_1−xAl₁₁O₁₉ with BaIr_xAl_12−xO₁₉ (x = 0–0.8), it was found that iridium was the active component in the N₂O decomposition and the framework iridium was more active than the large IrO₂ particles. On the other hand, Fe facilitated the formation of hexaaluminate as well as the incorporation of iridium into the framework.     

Catalytic oxidation of nitrogen monoxide over La1−xCexCoO3 perovskites

This paper presents an investigation on the NO oxidation properties of perovskite oxides. La_1−xCe_xCoO₃ (x = 0, 0.05, 0.1, 0.2, 0.3, 0.4) perovskite-type oxides were synthesized through a citrate method and characterized by XRD, BET and XPS. The catalytic activities were enhanced significantly with Ce substitution, and achieved the best when x was 0.2, but decreased at higher x values. The performed characterizations reveal that the adsorbed oxygen on the surface plays an important role in the oxidation of NO into NO₂. The surface compounds after the co-adsorption of NO and O₂ at room temperature, were investigated by DRIFTS and TPD experiments. Three species: the bridging nitrate, the hyponitrites and the monodentate nitrate, were formed on the surface. The order of thermal stabilities was as follows: monodentate > hyponitrite > bridging. Among them, only the monodentate nitrate which decomposed at above 300 °C, would desorb NO₂ into the gas phase. When Ce was added, the temperature of monodentate nitrate desorption became low and the adsorption of the other two species decreased. This might be related to the oxidation state of Co on the surface. Analysis by synthesizing the characterization results and catalytic activity data shows that large amounts of adsorbed oxygen, small amount of inactive compounds on the surface and low NO₂ desorption temperature are favorable for the oxidation of NO.     

Catalytic combustion of CH4 and CO on La1−xMxMnO3 perovskites

The activities of perovskites depend on compositions and preparation methods. Various perovskites, La_1−xM_xMnO₃ (M=Ag, Sr, Ce, La), have been prepared by two different methods (co-precipitation and spray decomposition). The new preparation method, spray decomposition, produced perovskites of a high surface area of over 10 m²/g. The catalytic activities for CH₄ and CO oxidation have been studied on a series of catalysts, La_1−xM_xMnO₃. The perovskite-type oxide, La_0.7Ag_0.3MnO₃, shows the highest catalytic activity: the complete conversion of CO and CH₄ at 370 and 825 K, respectively.     

A stabilization mechanism for the perovskite La2/3TiO3 compound with Fe2O3: A structural and electrical investigation

We have stabilized the perovskite La_2/3TiO₃ by adding LaFeO₃ and shown that in general the stabilization mechanism for the (1 − x)La_2/3TiO_3–xLaFeO₃ mixture involves the formation of a solid solution for compositions with x ≥ 0.04. The crystal structure of the solid solution transforms from orthorhombic to tetragonal at x = 0.2, becomes cubic in the range 0.3 < x < 0.8, and transforms again into orthorhombic (typical for pure LaFeO₃) for values greater than 0.8. Detailed impedance-spectroscopy measurements for various compositions and conditions showed that the limiting step in the conduction mechanism was conduction across the grain boundaries. In the concentration range 0.04 < x < 0.25 the room temperature conductivity increases up to 0.0017 S cm⁻¹, after which it decreases again. Part of the initial increase is probably due to the formation of free electrons in accordance with (Fe_Ti)′ → (Fe_Ti)^x + n′. Other defect-formation mechanisms are also discussed, but are ruled out for a variety of reasons. Another interesting phenomenon that also affected the average conductivity was identified, i.e., the variation of the average particle size with composition.     

Nanosized perovskite-type oxides La1−xSrxMO3−δ (M = Co, Mn; x = 0, 0.4) for the catalytic removal of ethylacetate

Nanometer perovskite-type oxides La_1−xSr_xMO_3−δ (M = Co, Mn; x = 0, 0.4) have been prepared using the citric acid complexing-hydrothermal-coupled method and characterized by means of techniques, such as X-ray diffraction (XRD), BET, high-resolution scanning electron microscopy (HRSEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD), and temperature-programmed reduction (TPR). The catalytic performance of these nanoperovskites in the combustion of ethylacetate (EA) has also been evaluated. The XRD results indicate that all the samples possessed single-phase rhombohedral crystal structures. The surface areas of these nanomaterials ranged from 20 to 33 m² g⁻¹, the achievement of such high surface areas are due to the uniform morphology with the typical particle size of 40–80 nm (as can be clearly seen in their HRSEM images) that were derived with the citric acid complexing-hydrothermally coupled strategy. The XPS results demonstrate the presence of Mn⁴⁺ and Mn³⁺ in La_1−xSr_xMnO_3−δ and Co³⁺ and Co²⁺ in La_1−xSr_xCoO_3−δ, Sr substitution induced the rises in Mn⁴⁺ and Co³⁺ concentrations; adsorbed oxygen species (O⁻, O₂⁻, or O₂²⁻) were detected on the catalyst surfaces. The O₂-TPD profiles indicate that Sr doping increased desorption of the adsorbed oxygen and lattice oxygen species at low temperatures. The H₂-TPR results reveal that the nanoperovskite catalysts could be reduced at much lower temperatures (<240 °C) after Sr doping. It is observed that under the conditions of EA concentration = 1000 ppm, EA/oxygen molar ratio = 1/400, and space velocity = 20,000 h⁻¹, the catalytic activity (as reflected by the temperature (T_100%) for EA complete conversion) increased in the order of LaCoO_2.91 (T_100% = 230 °C) ≈ LaMnO_3.12 (T_100% = 235 °C) < La_0.6Sr_0.4MnO_3.02 (T_100% = 190 °C) < La_0.6Sr_0.4CoO_2.78 (T_100% = 175 °C); furthermore, there were no formation of partially oxidized by-products over these catalysts. Based on the above results, we conclude that the excellent catalytic performance is associated with the high surface areas, good redox properties (derived from higher Mn⁴⁺/Mn³⁺ and Co³⁺/Co²⁺ ratios), and rich lattice defects of the nanostructured La_1−xSr_xMO_3−δ materials.     

Partial oxidation of methane to syngas over BaTi1 − xNixO3 catalysts

Performances of BaTi_1 − xNi_xO₃ perovskites, prepared using sol–gel method, as catalysts for partial oxidation of methane to syngas have been studied. The catalysts were characterized by XRD, BET and TEM. The experimental studies showed the calcination temperature and Ni content exhibited a significant influence on catalytic activity. Among catalysts tested, the catalyst BaTi_0.8Ni_0.2O₃ exhibited the best activity and excellent stability.