Optical absorption studies for TeO2-P2O5 and Bi2O3-TeO2-P2O5 glasses

A range of TeO₂-P₂O₅ and Bi₂O₃-TeO₂-P₂O₅ glass systems were prepared. The optical absorption spectra were measured in the spectral range 300–800 nm and it was found that the fundamental absorption of these glasses is dependent on the glass composition. The optical energy gap of binary glasses increases with increasing TeO₂ content while the addition of Bi₂O₃ to TeO₂-P₂O₅ decreases the optical energy gap. The absorption edges of these glasses arise from direct forbidden transitions and occur at photon energies in the range of 2.17 to 2.97 eV for TeO₂-P₂O₅ glasses and 2.63 to 2.32 eV for Bi₂O₃-TeO₂-P₂O₅ glasses depending on their composition.     

Study of structures and properties of ZnO-Sb2O3-P2O5-Na2O glasses

The influence of ZnO substitution by 0–12 wt.% Na₂O on the properties of ZnO-Sb₂O₃-P₂O₅-Na₂O glasses has been investigated. The structure and properties of the glasses with the composition of (13.86-x)ZnO-57.93Sb₂O₃-28.21P₂O_5?x Na₂O (x = 0–12 wt.%) were characterized by infrared spectra (IR), X-ray diffraction and differential thermal analysis (DTA). The results of IR indicated an increase in the intensity of symmetric vibrations of P-O-P bond, which was confirmed by the improvement of water durability with the increasing amount of Na₂O in the range of 0–10 wt.%. Substitution of 10 wt.% Na₂O led to the weight loss of the glass to 5.93 mg/cm^?2 after immersion in deionized water at 50 °C for 24 h. The results of XRD showed that the ability of crystallization decreased, indicating the good thermal stability of the glass. The glass containing 8 wt.% Na₂O had the best properties in every respect and might be an alternative to lead based glasses for the applications, providing further composition improvement.     

Mechanochemical synthesis of hydroxyapatite from Ca(OH)2-P2O5 and CaO-Ca(OH)2-P2O5 mixtures

Dry grinding of Ca(OH)₂-P₂O₅ and CaO-Ca(OH)₂-P₂O₅ mixtures was conducted by a planetary ball mill to investigate the mechanochemical solid-phase reaction for the synthesis of hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, HAp). HAp was synthesized by grinding of the two sets of mixtures. The formation of HAp from the Ca(OH)₂-P₂O₅ mixture was more advantageous than that from the CaO-Ca(OH)₂-P₂O₅ one. This synthesis reaction from the former mixture was almost completed within 30 min of grinding. The presence and amount of H₂O contained in the starting mixtures played a key role to promote the formation of HAp. Especially, in the former mixture, the prolonged grinding assisted the solid-phase reaction of the intermediate DCPD and Ca(OH)₂ to produce HAp more effectively.     

Compositional dependence of infrared absorption spectra studies for TeO2-P2O5 and TeO2-P2O5-Bi2O3 glasses

The infrared absorption spectra of the vitreous TeO₂-P₂O₅ and Bi₂O₃-TeO₂-P₂O₅ systems are studied in the spectral region of 4000 to 200 cm^–1. Absorption bands in this range are assigned. The midband wavenumber and the absorption intensity for the attributed bands are found to be strongly and systematically dependent on glass composition. Quantitative analysis was also attempted to justify our attribution of the observed bands.     

Evaluation of CaO-SiO2-P2O5-Na2O-Fe2O3 bioglass-ceramics for hyperthermia application

Magnetic bioglass ceramics (MBC) are being considered for use as thermoseeds in hyperthermia treatment of cancer. While the bioactivity in MBCs is attributed to the formation of the bone minerals such as crystalline apatite, wollastonite, etc. in a physiological environment, the magnetic property arises from the magnetite [Fe3O4] present in these implant materials. A new set of bioglasses with compositions 41CaO x (52-x)SiO2 x 4P2O5 x xFe2O3 x 3Na2O (2 < or = x < or = 10 mol% Fe2O3) have been prepared by melt quenching method. The as-quenched glasses were then heat treated at 1050 degrees C for 3 h to obtain the glass-ceramics. The structure and microstructure of the samples were characterized using X-ray diffraction and microscopy techniques. X-ray diffraction data revealed the presence of magnetite in the heat treated samples with x > or = 2 mol% Fe2O3. Room temperature magnetic property of the heat treated samples was investigated using a Vibrating Sample Magnetometer. Field scans up to 20 kOe revealed that the glass ceramic samples had a high saturation magnetization and low coercivity. Room temperature hysteresis cycles were also recorded at 500 Oe to ascertain the magnetic properties at clinically amenable field strengths. The area under the magnetic hysteresis loop is a measure of the heat generated by the MBC. The coercivity of the samples is another important factor for hyperthermia applications. The area under the loop increases with an increase in Fe2O3 molar concentration and the. coercivity decreases with an increase in Fe2O3 molar concentration The evolution of magnetic properties in these MBCs as a function of Fe2O3 molar concentration is discussed and correlated with the amount of magnetite present in them.     

H(2)O(2)-generating peroxidase electrodes as reagentless cyanide sensors

Inexpensive, reagentless, and simple (single-electrode) cyanide biosensors are developed using a pyrolytic graphite (PG) electrode on which horseradish peroxidase (HRP) is adsorbed. The electrode is poised at -300 mV vs Ag/AgCl for 40 s to reduce dissolved O(2) to H(2)O(2) at the PG surface. The generated H(2)O(2) accumulates in the diffusion layer. The potential is then stepped to 0 mV, at which the accumulated H(2)O(2) is reduced, though the O(2) reduction does not proceed. Since the H(2)O(2) reduction is catalyzed by HRP, the transient cathodic current is inhibited by cyanide. Therefore, the transient current is a function of the cyanide concentration. A HRP/PG electrode with saturated HRP coverage is reliable, and it can determine 10(-)(5)-10(-)(3) M cyanide. On the other hand, the electrode with lower HRP coverage is less reliable, though it is so sensitive as to detect 2 × 10(-)(7) M cyanide because the system is under kinetic control.     

Acoustic and optical Debye temperatures of the vitreous system CoO-Co2O3-P2O5

For the Co-P-O glass system, data have been assembled on acoustic Debye temperatures obtained from ultrasonic wave-velocity measurements, acoustic and optical Debye temperatures determined from infrared absorption studies, and optical Debye temperatures obtained from electrical conductivity measurements. It is argued that these quantities are systematically related in theory, and the relationships are substantiated by the experimental data.On leave from the Physics Department, Faculty of Science, Monofia University, Shebeen El-Kome, Egypt.     

Formation and investigation of p–n diode structures based on lanthanum manganites and Nb-doped SrTiO3

High quality La_2 / 3Ba_1 / 3MnO₃ (LBMO), La_2 / 3Ca_1 / 3MnO₃ (LCaMO) and La_2 / 3Ce_1 / 3MnO₃ (LCeMO) thin films were grown on Nb 0.1 wt.% doped conducting SrTiO₃(100) (STON) substrates. Asymmetric current–voltage relations measured for the LBMO/STON, LCaMO/STON and LCeMO/STON heterostructures at T = 78/300 K certified hole-doping of the manganite films. The diffusion voltage, corresponding to a steep current increase at forward bias has been estimated. The LCaMO/STON heterojunction showed possible impact of interfacial strain on the rectifying behavior, meanwhile, the LaCeMO/STON heterostructures demonstrated evidence of phase separation of the manganite film at the interface.     

Structural and microstructural transitions during phase separation and crystallization of Al2O3-SiO2-P2O5-Y2O3 glass

A highly refractory glass in the system Al₂O₃-SiO₂-P₂O₅-Y₂O₃ has been designed and produced such that, upon heating, an essentially fully crystalline glass—ceramic evolves containing mullite (nominally 3Al₂O₃·2SiO₂) and xenotime (YPO₄) as the final principal phases. Phase separation in this glass occurred during cooling from the melt and continued during annealing. XPS of the Al 2p, P 2p and the Y 3d electrons revealed that the average chemical environment of each of these elements is measurably different in the annealed glass and in the completely crystallized material. This indicates that the compositions of the separated glass phases are very different from those of the crystal phases which form from them. Additional rearrangement of the glass structure was observed at 1173 K. Extensive formation of mullite was initially detected at 1223 K and was followed by the crystallization of xenotime and the transient compounds of Y₄Al₂O₉, Y₂Si₂O₇, AlPO₄ and YP₅O₁₄. The optimum crystal nucleation and crystallization temperatures of 1173 and 1473 K, respectively, were determined from DTA, XRD, SEM and TEM studies.     

Solid-state reactions in V x O y (NH4VO3)-P2O5 and V x O y (NH4VO3)-(NH4)2HPO4 closed systems

Solid-state reactions in V _x O _y (NH₄VO₃)-P₂O₅ and V _x O _y (NH₄VO₃)-(NH₄)₂HPO₄ closed systems can be used to synthesize vanadyl hydrogen phosphate at 300°C and a variety of ammonium vanadium phosphates at lower and higher temperatures.     

添加Bi2O3对ZnO-B2O3-P2O5-SrO体系封接玻璃结构和性能的影响

采用熔融法制备了ZnO-B2O3-P2O5-SrO-Bi2O3系无铅磷酸盐封接玻璃,研究了Bi2O3对该体系玻璃的结构、特征温度、热膨胀系数和化学稳定性的影响。结果表明,随Bi2O3含量的增加,玻璃的密度增大,Tg、Tf先下降后趋于平缓,玻璃的热膨胀系数先上升后趋于平缓;化学稳定性先增强后降低,当Bi2O3为7mol时,达到极小值。     

Novel low-temperature synthesis of glasses and glass-ceramics in the B2O3-SiO2-P2O5 system

In recent years considerable progress has been made in electronic packaging substrate technology. The future need of miniaturization of devices to increase the signal processing speed calls for an increase in the device density requiring the substrates to be designed for better thermal, mechanical and electrical efficiency. Fast signal propagation with minimum delay requires the substrate to possess very low dielectric constant. Several glasses and glassceramic materials have been identified over the years which show good promise as candidate substrate materials. Among these, borophosphate and borophosphosilicate glass-ceramics have been recently identified to have the lowest dielectric constant (3.8). Sol-gel processing has been used to synthesize borosilicate, borophosphosilicate and borophosphate glasses and glass-ceramics using inexpensive boron oxide and phosphorus pentoxide precursors. Preliminary results of the processing of these gels and the effect of volatility of boron alkoxide and its modification on the gel structure are described. X-ray diffraction, differential thermal analysis and Fourier transform-infrared spectroscopy have been used to characterize the as-as-prepared and heat-treated gels.     

Infrared spectra of the vitreous system Co3O4-P2O5 and their interpretation

The infrared absorption spectra of the vitreous Co₃O₄-P₂O₅ system have been measured in the frequency region 4000 to 200 cm^–1. Absorption bands and mode attributions have been fully discussed. Absorption frequencies and intensities are found to be strongly and systematically dependent on glass composition. On this basis it is found that this glass system can be divided into three distinct compositional regions. Similar three region behaviour is reported for the compositional dependence of density and molar volume of mixing of Co₃O₄-P₂O₅ glass. Quantitative justification for the band attributions has been attempted.On leave from the Physics Department, Faculty of Science, Monofia University, Shebeen El-Kome, Egypt.     

ZnO-Al2O3-P2O5玻璃水化过程及机理的研究

研究了不同Al2O3/P2O3摩尔比和热历史的ZnO-Al2O3-P2O5玻璃在不同条件下的水化过程,利用XRD对部分水化过程的水化产物进行了晶相分析,探讨了其水化机理.结果表明:Al2O3/P2Os比的增加及退火均可降低ZnO-Al2O3-P2O5玻璃的水化速率;玻璃的水化累计失重量均与水化时间成线性关系,水失重百分数随着水化温度的提高,呈指数规律增加.研究认为:ZnO-Al2O3-P2O5玻璃的水化过程受表面水化层与内部未水化部分间的界面化学反应控制,水化过程中玻璃网络解体,相继生成了[P2O7]4-和白色不溶性物质Zn2P2O7·3H2O.     

Effect of the addition of Fe2O3 and heat treatment duration on the magnetic susceptibility of V2O5-P2O5-B2O3 glass system

The effect of the addition of Fe₂O₃ and heat treatment duration on the magnetic susceptibility of vanadium borophosphate glass were studied. The magnetic susceptibility of glass samples was found to increase with increasing Fe₂O₃ content, which may be explained by the formation of the FeO₆ group and the change of Fe²⁺ to Fe³⁺ which has higher paramagnetic properties. No detectable changes in the magnetic susceptibility with heat treatment for the samples containing 0.0, 0.5 and 1.0 mol% Fe₂O₃ was observed. The magnetic susceptibility for the heat treated samples containing 2.5, 5.0 and 7.5 mol% Fe₂O₃ decreases sharply with increasing duration of heat treatment up to 6 h and then remains almost constant. The sharp decrease in magnetic susceptibility of 2.5 mol% Fe₂O₃ is attributed to the increase in the number of ferrous ions. The sharp decrease for samples containing 5.0 and 7.5 mol% Fe₂O₃ is attributed to the increase in the number of Fe³⁺ in tetrahedral co-ordination. The rate of crystallization owing to the heat treatment was calculated and was found to increase with increasing iron oxide content. The geometry of crystallization was found to be in three-, two-and one-dimension(s) for samples containing 2.5, 5.0 and 7.5 mol% Fe₂O₃, respectively.     

Synthesis and structural study of new potassium uranyl selenates K2(H5O2)(H3O)[(UO2)2(SeO4)4(H2O)2](H2O)4 and K3(H3O)[(UO2)2(SeO4)4(H2O)2](H2O)5

Single crystals of new uranyl selenates K₂(H₅O₂)(H₃O)[(UO₂)₂(SeO₄)₄(H₂O)₂](H₂O)₄ (1) and K₃(H₃O)[(UO₂)₂(SeO₄)₄(H₂O)₂](H₂O)₅ (2) were prepared by isothermal evaporation at room temperature. The crystal structure of 1 was solved by the direct method [C2/c, a = 17.879(5), b = 8.152(5), c = 17.872(5) Å, β = 96.943(5)°, V = 2585.7(19) ų, Z = 4] and refined to R ₁ = 0.0449 (wR ₂ = 0.0952) for 2600 reflections with |F _o| ≥ 4σ _F . The structure of 2 was solved by the direct method [P2₁/c, a = 17.8377(5), b = 8.1478(5), c = 23.696(1) Å, β = 131.622(2)°, V = 2574.5(2) ų, Z = 4] and refined to R ₁ = 0.0516 (wR ₂ = 0.1233) for 4075 reflections with |F _o| ≥ 4σ _F . The structures of 1 and 2 are based on [(UO₂)₂(SeO₄)₄(H₂O)₂]^4? layers. The charge of the inorganic layer is compensated by potassium and oxonium ions arranged in the interlayer space. Each K ion is surrounded by seven O atoms belonging to uranyl selenate layers and water molecules, so that it binds with each other the adjacent uranyl selenate structural elements.     

Novels patterns of hydration and new compounds in the ternary system of CaO-Al2O3-P2O5

 The patterns of hydrating and solidifying with the compositional variation of phosphorus-rich, phosphorus-calcium-rich and aluminum-calcium rich regions in ternary system CaO-Al₂O₃-P₂O₅ has been studied in detail, and two new ternary compounds L and H have been synthesized here. The results indicate that the region of 48–56% P₂O₅ doesn’t present cementitiousness, which contains mainly crystal phases of β-C₂P(2CaO·P₂O₅), α-C₃P(3CaO·P₂O₅) and AlPO₄; the phosphorus-calcium-rich region of 21–35% P₂O₅ exhibits substantial cementitiousness, which contains mainly crystal phase of α-C₃P and certain amount of CA(CaO·Al₂O₃) and new phases L/H; and the aluminum-calcium-rich region of 8–18% P₂O₅ is full of promise for cementitiousness. It contains mainly new crystal phase L and certain amount of α-C₃P and CA. The hydration and solidification mechanisms have been preliminarily analyzed by means of XRD, XPS and DTA. It appears that crystal phase CA might hydrate directly to the stable phase of C₃A·6H₂O in the phosphorus-rich case of 21–35% P₂O₅; new phase H has the behavior of rapid setting; and L, being a dominant phase, can prevent cement pastes from significant strength loss in long curing cycles. Received: 12 March 1998 / Accepted: 29 July 1998