Phase Transitions in the System BaTiO3—KnbO3

Solid solution formation in the system BaTiO₃—KnbO₃ was established by X-ray diffraction and dielectric measurements. Solid solutions with cubic symmetry were observed in the composition range from 4 to 90 mole % KnbO₃ at room temperature. The lattice parameter for the BaTiO₃ solid solutions increased with increasing KNbO₃; that for the KnbO₃ solid solutions decreased with the addition of BaTiO₃. A distinct discontinuity in lattice parameter was observed at the composition containing about 65 mole % BaTiO₃. Dielectric measurements were made from-195° to 400°C. The cubic-tetragonal transition temperature of BaTiO₃ was rapidly lowered with increasing addition of KNbO₃, whereas the two lower phase transition temperatures were raised. All three phase transitions of KnbO₃ were rapidly lowered with increasing addition of BaTiO₃. The observed phase transitions, lattice parameters, and electron probe data suggest a complex region in the subsolidus which extends from 35 to about 75 mole % KNbO₃.     

Ferroelectric Phase Transitions in the System PbTiO3,-KNbO3,

The formation of a complete series of solid solutions in the system PbTiO₃-KNbO₃ was established by X-ray and dielectric studies. The room-temperature symmetry of the entire system was tetragonal except for compositions containing more than 96 mole % KNbO₃, which had orthorhombic symmetry. The axial ratio, c/a , and the ferroelectric Curie temperature decreased from both the end-members. The lowest Curie temperature observed in the system was 175°C for the composition with 80 mole % KNbO₃. A generalization has been made on the variation of ferroelectric Curie temperatures with compositions in binary systems of perovskitetype solid solutions with and without a common cation.     

Effect of BiScO3 and LiNbO3 on the Piezoelectric Properties of (Na0.5K0.5)NbO3 Ceramics

Lead-free potassium sodium niobate-based piezoelectric ceramics (1− y )(Na_{0.5−0.5 x} K_{0.5−0.5 x} Li _x )NbO₃− y BiScO₃ (  y =0.01, x= 0–0.06) have been prepared by an ordinary sintering process. The XRD analysis showed that the structure changes from orthorhombic to tetragonal with the increase of x (at y =0.01, abbreviated as KNNBSL100 x ). At room temperature, the polymorphic phase transition from the orthorhombic to the tetragonal phase was identified at approximately 0.02≤ x ≤0.04. The piezoelectric and ferroelectric properties were significantly enhanced. The temperature dependences of the relative permittivity revealed that the Curie temperature was increased with the addition of LiNbO₃. These solid solution ceramics are promising as potential lead-free candidate materials.     

Phase Equilibria of the La2O3-SrO-CuO System at 950°C and 10 kbar

Phase equilibria of the La₂O₃-SrO-CuO system have been determined at 950°C and 10 kbar (1 GPa). Stable phases at the apices of the ternary phase diagram are CuO, La₂O₃, and SrO. Stable intermediate phases are La₂CuO₄ in the LaO_1.5-CuO binary and Sr₂CuO₃, SrCuO₂, and Sr₁₄Cu₂₄O₄₁ in the CuO-SrO binary. The La_2-xSr _x CuO_4-δ solid solution is stable where 0.0 ≤ x ≤ 1.3, the La_2-xSr_1+xCu₂O_6+δ solid solution is stable where 0.0 ≤ x ≤ 0.2, the La_8-xSr _x Cu₈O_20-δ solid solution is stable where 1.3 ≤ x ≤ 2.7, the La _x Sr_14-x-Cu₂₄O₄₁ solid solution is stable where 0 ≤ x ≤ 6, and the La_1+xSr_2-xCu₂O_5.5+δ phase is stable where 0.04 ≤ x ≤ 0.16. The La₂O₃-SrO-CuO phase diagram at 950°C and 10 kbar is almost identical to that determined by other authors at 950°C and 1 atm, in terms of phase stability and solid-solution ranges.     

Structure and Dielectric Properties of the Ba(Mg1/3Nb2/3)O3-La(Mg2/3Nb1/3)O3 System

A complete range of perovskite solid solutions can be formed in the (1 − x )Ba(Mg_1/3Nb_2/3)O₃- x La(Mg_2/3Nb_1/3)O₃ (BMN-LMN) pseudobinary system. While pure BMN adopts a 1:2 cation ordered structure, 1:1 ordered phases are stabilized for 0.05 ≤ x ≤ 1.0. Dark-field TEM images indicate that the La-doped solid solutions are comprised of large 1:1 ordered domains and no evidence was found for a phase-separated structure. This observation coupled with the systematic variations in the intensities of the supercell reflections supports a charge-balanced "random-site" model for the 1:1 ordering. The substitution of La also induces a transformation from a negative to positive temperature coefficient of capacitance in the region 0.25 ≤ x ≤ 0.5.     

Phase Relations in the System UO2-UO3– Y2O3

The phase relations in the system U02-U03-Yz03, particularly in the Y203-rich region, were examined by X-ray and chemical analyses of reacted powders heated at temperatures up to 1700°C in H₂, CO₂-CO₂ and air. Four phases were identified in the system at temperatures between 1000° and 1700°C: U308, face-centered cubic solid solution, body-centered cubic solid solution, and a rhombohedral phase of composition (U,Y)₇O₂ ranging from 52.5 to 75 mole % Y₂O₃. The rhombohedral phase oxidized to a second rhombohedral phase with a nominal composition (U,Y), at temperatures below 1000°C. This phase transformed to a face-centered cubic phase after heating in air above 1000° C. The solubility of UO, in the body-centered cubic phase is about 14 mole % between 1000° and 1700°C but decreases to zero as the uranium approaches the hexavalent oxidation state. The solubility of Yz03 in the face-centered cubic solid solution ranges from 0 to 50 mole % Y2O3 under reducing conditions and from 33 to 60 mole % Y2O3 under oxidizing conditions at 1000°C. At temperatures above 1000° C, the face-centered cubic solid solution is limited by a filled fluorite lattice of composition (U,Y)O₂. For low-yttria content, oxidation at low temperatures (<300°C) permits additional oxygen to be retained in the structure to a composition approaching (U,Y)O_2.25 A tentative ternary phase diagram for the system UO₂-UO₃-Y₂O₃ is presented and the change in lattice parameter and in cell volume for the solid-solution phases is correlated with the composition.     

Ferroelectric and Structural Properties of the Pb(Sc1/2Nb1/2)1-x,Tix,O3 System

Extensive solid solution was observed in the system Pb(Sc_1/2/,Nb_1/2,)_1-x,Ti_x,O₃. In the range 0 ≤ x ≤ 0.425 a rhombohedral ferroelectric phase was stable at 25° C. In the range 0.45 ≤ x ≤ 1.00 a tetragonal ferroelectric phase was stable at this temperature. The phase diagram of the system below 500° C strongly resembles that of PbZrO₃−PbTiO₃. The compound Pb(Sc_1/2Nb_1/2)O₃ exhibited rhombohedral perovskite cell symmetry below the ferroelectric ↔ paraelectric transition temperature, and the angle a was acute. The radial coupling coefficient was 0.46 for the composition Sc_1/2Nb_1/2)_0.575Ti_0.4250O₃. At 25°C this composition consisted primarily of the rhombohedral phase with a small amount of the tetragonal phase present. The ferroelectric ↔ paraelectric transition occurred over a temperature range in the rhombohedral phase field. The spontaneous polarization was finite at temperatures considerably above the temperature of the permittivity maximum for a given rhombohedral solid solution.     

BiScO3 Doped (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

Lead-free potassium sodium niobate-based piezoelectric ceramics (1− x )(Na_0.5K_0.5)NbO₃– x BiScO₃ (KNN–BS) ( x =0∼0.05) have been prepared by an ordinary sintering process. Single perovskite phase of KNN–BS exhibits an orthorhombic symmetry at x <0.015 and pseudocubic symmetry at x >0.02, separating by a MPB at 0.015≤ x ≤0.02. Piezoelectric and ferroelectric properties are significantly enhanced in the MPB, which are as follows: piezoelectric constant d ₃₃=203 pC/N, planar coupling coefficient k _p=0.36, remnant polarization P _r=24.4 μC/cm². These solid solution ceramics look promising as a potential lead-free candidate materials.     

30 kbar Phase Equilibria of the La2O3–SrO–CuO System at 950°C

Phase equilibria of the La₂O₃–SrO–CuO system have been determined at 950°C at 30 kbar (3 GPa). Stable phases at the apexes of the ternary phase diagram are CuO, La₂O₃, and SrO. Stable intermediate phases are La₂, CuO₄ and La₂Cu₂O₅ in the LaO_1.5–CuO binary and Sr₂CuO₃, SrCuO₂, and Sr₁₄Cu₂₄O₄₁ in the CuO–SrO binary. The La_{2– x} Sr _x -CuO_4–δ solid solution is stable for 0.00 is ≤ x ≤ 1.29, the La_{2– x} Sr_{1+ x} Cu₂O_6+δ solid solution is stable for 0.03 ≤ x ≤0.20, the La_{2– x} Sr _x Cu₂O_5–δ solid solution is stable for 0.00 ≤ x ≤1.08, and the La _x Sr_{14– x} Cu₂₄O₄₁ solid solution is stable for 0.00 ≤ x ≤ 6.15. The 30 kbar phase diagram differs from the 1 atm (0.1 MPa) and 10 kbar (1 GPa) results principally in the absence of La_{1– x} Sr_{2+ x} Cu₂O_5.5+δ as a stable phase and the extended range of the La_{2– x} Sr _x Cu₂O_5–δ solid solution at 30 kbar.     

Polymorphism of BaTiO3 Acceptor Doped with Mn3+, Fe3+, and Ti3+

The effect of Mn doping on the cubic to hexagonal phase transition temperature in BaTiO₃ has been determined by quenching samples with different Mn contents from a range of temperatures. Under conditions of equilibrating samples in air over the range 1000°–1400°C, cubic solid solutions BaTi_{1− x} Mn _x O_3−δ form over the range 0≤ x ≤0.015(5), whereas hexagonal solid solutions form for x ≥0.02, depending on the temperature. The results are compared with those on doping BaTiO₃ with Fe³⁺ and observations made concerning acceptor doping with Ti³⁺.     

Phase Diagram and Oxygen-Ion Conductivity in the Y2O3-Nb2O5 System

The phase equilibria in the Y₂O₃-Nb₂O₅ system have been studied at temperatures of 1500° and 1700°C in the compositional region of 0-50 mol% Nb₂O₅. The solubility limits of the C-type Y₂O₃ cubic phase and the YNbO₄ monoclinic phase are 2.5 (±1.0) mol% Nb₂O₅ and 0.2 (±0.4) mol% Y₂O₃, respectively, at 1700°C. The fluorite (F) single phase exists in the region of 20.1-27.7 mol% Nb₂O₅ at 1700°C, and in the region of 21.1-27.0 mol% Nb₂O₅ at 1500°C, respectively. Conductivity of the Y₂O₃- x mol% Nb₂O₅ system increases as the value of x increases, to a maximum at x = 20 in the compositional region of 0 ≤ x ≤ 20, as a result of the increase in the fraction of F phase. In the F single-phase region, the conductivity decreases in the region of 20-25 mol% Nb₂O₅, because of the decrease in the content of oxygen vacancies, whereas the conductivity at x = 27 is larger than that at x = 25. The conductivity decreases as the value of x increases in the region of 27.5 ≤ x ≤ 50, because of the decrease in the fraction of F. The 20 mol% Nb₂O₅ sample exhibits the highest conductivity and a very wide range of ionic domain, at least up to log p _O2=−20 (where p _O2 is given in units of atm), which indicates practical usefulness as an ionic conductor.     

Crossover of Ba(Ti,Y)O3 Solid Solutions to Ba3Ti2YO8.5–BaTiO3 Composites and their Dielectric Properties

Ceramic samples with the nominal composition (1− x ) BaTiO₃+ x Ba₃Ti₂YO_8.5 ( x =0−0.535) were prepared by the mixed oxide method. X-ray diffraction (XRD) analysis shows that the materials are of single phase with a cubic symmetry as x ≤0.16. The compositions of the solid solutions ( x ≤0.16) can be expressed equivalently as Ba(Ti_{1− y} Y _y )O_3−δ ( y ≤0.122, y = x /(1+2 x )). For x >0.16, the materials are diphasic composites consisting of Ba(Ti_{1− y} Y _y )O₃ ( y =0.122) and Ba₃Ti₂YO_8.5. The microstructure observation by scanning electron microscopy supports the XRD result. The dielectric behavior and phase transitions of the solid solutions ( x ≤0.16) vary with different Y concentrations. The dielectric constant of the composites ( x >0.16) follows approximately the Lichteneker relation in a wide temperature range.     

Cation Ordering Transformations in the Ba(Zn1/3Nb2/3)O3-La(Zn2/3Nb1/3)O3 System

Single-phase perovskites were formed in the (1−_x)Ba(Zn_1/3Nb_2/3)O₃-( _x )La(Zn_2/3Nb_1/3)O₃ system for compositions with 0.0≤ x ≤0.6. Although the stability of the trigonal "1:2" ordered structure of the Ba(Zn_1/3Nb_2/3)O₃ end member is very limited (0.0≤ x ≤0.05), low levels of lanthanum induce a transformation to a cubic, "1:1" ordered structure that has a broad range of homogeneity (0.05≤ x ≤0.6). Samples with x > 0.6 were comprised of La₃NbO₇, ZnO, and a perovskite with x = 0.6. The cubic 1:1 phases were fully ordered and no evidence was found for a compositionally segregated microstructure. These observations could not be reconciled in terms of a "space-charge" model; rather, they supported a charge-balanced, "random-site" structure for the 1:1 cation-ordered Ba(β_1/2'β_1/2")O₃ phases.     

Quaternary Compounds Prepared in a CaO–Y2O3–SnO2 System

Compounds in a CaO–Y₂O₃–SnO₂ system were prepared by a solid-state reaction at 1673 K. The phase relation in this system was investigated by powder X-ray diffraction. Besides the previously reported ternary compounds, CaSnO₃, Ca₂SnO₄, Y₂Sn₂O₇, and a quaternary compound Ca_0.4Y_1.2Sn_0.4O₃, solid-solution series of Ca_{2− x} Y_{2 x} Sn_{1− x} O₄ with 0≤ x ≤0.5, and Ca_{1− y} Y_{2 y} Sn_{1− y} O₃ with 0≤ y ≤0.2 and 0.95≤ y ≤1.0 were found. The cell parameters of these solid-solution series were refined. The changes of rhombohedral cell parameters in the samples prepared in the range 0.565< y <0.714 of Ca_{1− y} Y_{2 y} Sn_{1− y} O₃ suggested the existence of solid solutions of Ca_0.4Y_1.2Sn_0.4O₃, although their single phases could not be prepared, except at y =0.6.     

Phase Diagram of the BaO(BaCO3)-CaO-CuO System

The phase diagram of the BaO(BaCO₃)-CaO-CuO system, especially in the barium-rich region at 900°C in air, was studied. Two new different oxycarbonates were observed: Ba₈Ca_16/15Cu_64/15O_11.20(CO₃)_2.66and a solid-solution series with a chemical composition of Ba₂Ca _{x + y} Cu_{1+( x /2)- y} O_2+delta(CO₃)_{1- z} (where 0 ≤ to x ≤ to 2/39 and 0 ≤ to y ≤ to 16 x /5). The oxycarbonate solid solution was formed in a region of the compositional triangle Ba:Ca:Cu (in moles) = (2:0:1)-(39:1:20)-(65:7:28). The solid-solution structure had P 4/ mmm symmetry, with lattice parameters a similar/congruent a _pand c similar/congruent 2 a _p, where a _prepresents the perovskite cell. The Ba₈Ca_16/15Cu_64/15O_11.20(CO₃)_2.66compound, which had Pm 3 m symmetry with a lattice parameter a = 0.8116(2) nm, had no chemical-solubility range.     

Subsolidus Phase Relationships in the Ga2O3–Al2O3–TiO2 System

Subsolidus phase relationships in the Ga₂O₃–Al₂O₃–TiO₂ system at 1400°C were studied using X-ray diffraction. Phases present in the pseudoternary system include TiO₂ (rutile), Ga_{2−2 x} Al_{2 x} O₃ ( x ≤0.78 β-gallia structure), Al_{2−2 y} Ga_{2 y} O₃ ( y ≤0.12 corundum structure), Ga_{2−2 x} Al_{2 x} TiO₅ (0≤ x ≤1 pseudobrookite structure), and several β-gallia rutile intergrowths that can be expressed as Ga_{4−4 x} Al_{4 x} Ti _{n −4}O_{2 n −2} ( x ≤0.3, 15≤ n ≤33). This study showed no evidence to confirm that aluminum substitution of gallium stabilizes the n =7 β-gallia–rutile intergrowth as has been mentioned in previous work.     

Surface Chemical and Leakage Current Density Characteristics of Nanocrystalline Ag–Ba0.5Sr0.5TiO3 Thin Films

Nanocrystalline x Ag–(1− x )Ba_0.5Sr_0.5TiO₃ (Ag–BST, 0≤ x ≤0.1, where x is the mole fraction of Ag) thin films have been deposited on Pt/Ti/SiO₂/Si substrates by a sol–gel method. The films have been characterized by X-ray diffraction (XRD), scanning electron microscopy, and X-ray photoelectron spectroscopy (XPS). The core-level XPS of oxygen (O1 s ) of the Ag–BST films indicate that an optimum amount of Ag ( x =0.02 or 2 mol%) enhances the binding energy of oxygen, possibly through a mechanism in which the electrophilic oxygen dissociates from the Ag surface and fills the oxygen vacancies. Similarly, the binding energy of Ag (Ag3 d ) shows a shift toward a higher value with increasing Ag up to 4 mol%, probably because of the chemical shift of Ag in BST along the surface layers, surface relaxation, or changes in the Fermi level of small Ag particles in the solid solution range of Ag in BST films ( x ≤0.04). The leakage current density of 2 mol% Ag-added BST (∼10⁻⁶ A/cm²) is less by about an order of magnitude than pure BST at an electric field of 200 kV/cm. A defect model is proposed to explain the observed leakage current density of Ag–BST films satisfactorily.     

Electrical Conductivity in the ZrO2-Rich Region of Several M2O3—ZrO2 Systems

The electrical conductivity of M₂O₃-ZrO₂ compositions containing 6 to 24 mole % M₂O₃, where M represents La, Sm, Y, Yb, or Sc, was examined. Only Sm₂O₃, Y₂O₃, and Yb₂O₃ formed cubic solid solutions with ZrO₂ over most of this substitutional range. Scandia forms a wide cubic solid solution region with ZrO₂ at temperatures above 130°C whereas the cubic solid solution region at room temperature is narrow (6 to 8 mole % Sc₂O₃). Lanthana additions to ZrO₂produced no fluorite-type cubic solid solutions within the compositional range investigated. Generally, the electrical conductivity of these cubic solid solutions increased as the size of the substituted cation decreased and the electrical conductivity for each binary system attained a maximum at about 10 to 12 mole % M₂O₃.     

Microstructure and Dielectric Characteristics of (PbxBa0.5−xSr0.5)TiO3 Ceramics

Microstructural and dielectric properties of the Pb _x Ba _0.5__x —Sr_0.5TiO₃ system have been studied. It is found that this system forms a solid solution in the entire composition range (0.0≤ x ≤0.5) and is cubic for the x = 0, 0.1, and 0.2 compositions and tetragonal for other compositions. Measurements of the dielectric constant as a function of temperature reveal that this material is ferroelectric at room temperature for the x > 0.2 compositions and has a broad paraelectric-ferroelectric transition region. No shift in the dielectric maxima was noted; however, there is a slight spread in the dielectric constant with frequency for the x = 0.4 composition. A quantitative model to mathematically analyze the effect of composition fluctuations on the dielectric broadening for a ternary system is presented. Transmission electron microscopic studies reveal the presence of 90° ferroelectric domains oriented along the {01     } planes for the x = 0.3 and 0.4 compositions.     

Structural and Dielectric Characterization of Nanocrystalline (Ba, Pb)ZrO3 Developed by Reverse Micellar Synthesis

Nanocrystalline zirconates of barium and lead have been synthesized using a modified reverse micellar route (avoiding alkoxides). The entire solid solution of Ba_{1− x} Pb _x ZrO₃ (0≤x≤1) has been synthesized for the first time. Powder X-ray diffraction studies show the monophasic nature of the powders after heating at 800°C except minor impurities of ZrO₂ (2%–3%) at a higher lead content ( x =0.50 and 0.75). The oxides crystallize in the cubic structure till x =0.25; for higher values, they crystallize in the orthorhombic structure. The particle size obtained from X-ray line-broadening studies and transmission electron microscopic studies is found to be in the range of 20–60 nm for all the oxides obtained after heating at 800^oC. The grain size of the solid solution of Ba_{1− x} Pb _x ZrO₃ (0≤ x ≤1) was found to increase with the lead content. The dielectric constant of the solids corresponding to Ba_{1− x} Pb _x ZrO₃ (0≤ x ≤1) was found to be a maximum at x =0.50. Note that the cubic to orthorhombic transition is also observed between x =0.25 and 0.5. Dielectric properties with respect to variation in frequency and temperature are reported for these nanocrystalline oxides for the first time.