SiC and ZrN nano-particulate reinforced AlON composites: Preparation,mechanical properties and toughening mechanisms

Due to excellent chemical stability, high rigidity, superior corrosion and wear resistance, aluminum oxynitride (AlON) has been considered as one of most promising candidate ceramic materials in high-performance structural, advanced abrasives and refractory fields. However, it usually exhibited relatively low flexural strength and poor fracture toughness. The study is aimed to develop silicon carbide (SiC) and zirconium nitride (ZrN) nano-particulate reinforced AlON composites with improved mechanical properties and fracture resistance via a hot-press sintering process. It was found that the addition of ZrO₂ nanoparticles would be transformed into ZrN during sintering. Due to the pinning effect of SiC and ZrN nano-particles positioned at grain boundaries of micro-sized AlON particles, the presence of SiC and ZrN nano-particles resulted in the reduction of both porosity and grain size, and a change of fracture mode from intergranular cracking in AlON to intragranular cracking in composites. With presence of 8 wt% SiC and 5.2 wt% ZrN nano-particles, the relative density, microhardness, Young’s modulus, flexural strength and fracture toughness increased. Different toughening mechanisms including crack bridging, crack branching and crack deflection were observed, thus effectively increasing the crack propagation resistance and leading to a considerable improvement in flexural strength and fracture toughness.     

Evaluation of mechanical reliability of zirconia-toughened alumina composites for dental implants

Zirconia-toughened alumina composites containing 0–30 vol% of 3Y-TZP were fabricated by sintering at 1600 °C for 2 h in air. The effect of the 3Y-TZP content on the mechanical properties and microstructure of the alumina ceramics was investigated. The fracture toughness and biaxial flexural strength increased as the 3Y-TZP content increased. The Young's modulus decreased with 3Y-TZP content according to the rule of mixture, while the hardness showed the contrary tendency. The Weibull modulus of the Al₂O₃ with 20 vol% 3Y-TZP composite is higher than that of alumina. The residual hoop compressive stress developed in ZTA ceramic composites probably accounts for the enhancement of strength and fracture toughness, as well as for the higher tendency of crack deflection. No monoclinic phase and strength degradation were found after low temperature degradation (LTD) testing. The excellent LTD resistance can be explained by the increased constraining force on zirconia embedded in alumina matrix.     

Thermal shock behavior of nano-sized ZrN particulate reinforced AlON composites

Aluminum oxynitride (AlON) has been considered as a potential ceramic material for high-performance structural and advanced refractory applications owing to its excellent stability and mechanical properties such as high rigidity and good chemical stability. Thermal shock resistance is a major concern and an important performance index of refractories and high-temperature ceramics. While zirconium nitride (ZrN) particles have been proven to improve mechanical properties of AlON ceramic, the thermal shock behavior has not been evaluated yet. The aim of this investigation was to identify the thermal shock resistance and underlying mechanisms of hot-pressed 2.7% ZrN–AlON composites by a water-quenching technique over a temperature range between 225 °C and 275 °C. The residual strength and Young's modulus after thermal shock decreased with increasing temperature range and thermal shock times due to large temperature gradients and thermal stresses caused by abrupt water-quenching. The presence of nano-sized ZrN particles exhibited a positive effect on the improvement of both residual strength and critical temperature difference of AlON ceramic due to the toughening effects, the higher thermal conductivity of ZrN, the refined grain size and the reduction of porosity. Different toughening mechanisms including crack deflection, crack bridging and crack branching were observed during thermal shock experiments, thus effectively enhancing the crack initiation and propagation resistance and leading to a considerable improvement in thermal shock resistance in the ZrN–AlON composites.     

Grain size effect on the mechanical properties of transparent spinel ceramics

Transparent ceramics receive increasing interest in technical window applications. The mechanical reliability of transparent MgAl₂O₄ with different grain sizes was characterized. The investigations were based on a combination of micro- and macro-mechanical methods to assess Young's modulus, hardness, fracture toughness, crack kinetics and strength, the latter being analyzed using two- and three-parameter Weibull statistics. The effect of subcritical crack growth under ambient conditions was assessed using a strength–probability–time plot. It has been verified that increasing grain size decreases strength and increases slow crack growth sensitivity, but on the other hand appears also to increase the Weibull modulus and the impact and wear relevant hardness indentation size effect. Complementary fractography by optical, confocal and scanning electron microscopy permitted to gain insight into the failure origins.     

Enhancement of PVC/ENR blend properties by poly(methyl acrylate) grafted oil palm empty fruit bunch fiber

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150°C, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Young's modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Young's modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the impact strength, UTS, and elongation at break of the composites were found to decrease with the increase in fiber loading. An increase in elongation at break and UTS and decrease in the flexural and Young's modulus was observed with the addition of PMA‐g‐OPEFB fiber compared to ungrafted fiber. This observation indicates that grafting of PMA onto OPEFB impart some flexibility to the blend. The morphology of cryogenically fractured and tensile fracture surfaces of the composites, examined by a scanning electron microscope shows that the adhesion between the fiber and the matrix is improved upon grafting of the OPEFB fiber. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fabrication and mechanical properties of Al2O3-SiCw-TiCnp ceramic tool material

Whiskers and nanoparticles are usually used as reinforcing additives of ceramic composite materials due to the synergistically toughening and strengthening mechanisms. In this paper, the effects of TiC nanoparticle content, particle size and preparation process on the mechanical properties of hot pressed Al₂O₃-SiC_w ceramic tool materials were investigated. The results showed that the Vickers hardness and fracture toughness of the materials increased with the increasing of TiC content. The optimized flexural strength was obtained with TiC content of 4 vol% and particle size of 40 nm. The particle size has been found to have a great influence on flexural strength and small influence on hardness and fracture toughness. It was concluded that the flexural strength increased remarkably with the decreasing of the TiC particle size, which was resulted from the improved density and refined grain size of the composite material due to the dispersion of the smaller TiC particle size. SEM micrographs of fracture surface showed the whiskers to be mainly distributed along the direction perpendicular to the hot-pressing direction. The fracture toughness was improved by whisker crack bridging, crack deflection and whisker pullout; the TiC nanoparticles in Al₂O₃ grains caused transgranular fracture and crack deflection, which improved the flexural strength and fracture toughness with whiskers synergistically. Uniaxial hot-pressing of SiC whisker reinforced Al₂O₃ ceramic composites resulted in the anisotropy of whiskers’ distribution, which led to crack propagation differences between lateral crack and radical crack.     

Thermophysical Properties of Alumina Particle Reinforced Glass Matrix Composites

Alumina particles incorporated glass matrix composites, which showed good prospect to be used as coating materials for high‐temperature corrosion protection on intermetallics or titanium alloys, were prepared via pressureless sintering. With increasing alumina content, the Young's modulus, fracture strength, Vickers hardness, indentation toughness, softening point, and thermal shock resistance of the composites increased monotonically. A similar increasing trend could be found for the thermal expansion coefficient of the composites, except for an abnormal drop at small amount of incorporation, which closely correlated with the Al³⁺ dissolution into the glass matrix.     

Silicon Carbide Platelet/Alumina Composites: II, Mechanical Properties

The mechanical properties, i.e., Young's modulus, fracture toughness, and flexural strength, of SiC-platelet/Al₂O₃ composites with two different platelet sizes were studied. Both Young's modulus and the fracture toughness of composites using small platelets (12 μm) increased with increasing SiC volume fraction. Maximum values for toughness and Young's modulus of 7.1 MPa·m^1/2 and 421 GPa were obtained for composites containing 30 vol% platelets. Composites fabricated using larger platelets (24 μm), however, showed spontaneous microcracking at SiC volume fractions of ≤0.15. The presence of microcracks decreased Young's modulus and the fracture toughness substantially. Two types of radial microcracks were identified by optical microscopy and found to be consistent with a residual stress analysis. Anisotropy in fracture toughness was identified with a crack length indentation technique. Cracks propagating in a plane parallel to platelet faces experienced the least resistance, which was the the lowest toughness plane in platelet composites with preferred orientation. Enhanced fracture toughness was found in the plane parallel to the hot-pressing direction, but no anisotropy in toughness was observed in this plane. The flexural strength of alumina showed a decrease from 610 to 480 MPa for a 30 vol% composite and was attributed to the presence of the platelets.     

Boron nitride nanotubes as a reinforcement for brittle matrices

Cylindrical and bamboo-like boron nitride nanotubes (BNNTs) have been used to reinforce brittle amorphous borosilicate glass matrix materials prepared by spark plasma sintering. The mechanical properties, such as hardness, Young's modulus, fracture toughness, and scratch resistance of the materials have been investigated. The fracture toughness of the composites showed an improvement of ∼30% compared to the pure amorphous glass. BNNTs pull-out, crack bridging, stretching, and crack deflection toughening mechanisms were observed in the reinforced glass matrix composites. Extensive pull-out of the BNNTs (>400 nm) was observed in the form of the telescopic “sword-in-sheath” mechanism, resulting in poor energy dissipation due to the weak Van der Waals force between the inner walls of the BNNTs. The scratch resistance was significantly improved (∼26%) after the addition of the BNNTs, and the results correspond well with the brittleness index of the materials.     

The microstructural and mechanical properties of geopolymer composites containing glass microfibres

This paper presents the effects of microfibre contents on mechanical properties of fly ash-based geopolymer matrices containing glass microfibres at 0, 1, 2 and 3 mass%. The influence of glass microfibres on the fracture toughness, compressive strength, Young's modulus and hardness of geopolymer composites are reported, as are the microstructural properties investigated using scanning electron microscopy. Results show that the addition of 2 mass% glass microfibres was optimal, exhibiting the highest levels of fracture toughness, compressive strength, Young's modulus and hardness. The results of the microstructural analysis indicate that the glass microfibres act as a filler for voids within the matrix, making a dense geopolymer and improving the microstructure of the binder. This leads to favourable adhesion of the composites, and produces a geopolymer composite with good mechanical properties, comparable to pure geopolymer. The failure mechanisms in glass microfibre-reinforced geopolymer composites are discussed in terms of microstructure.     

Mechanical and tribological properties of TiB2-SiC and TiB2-SiC-GNPs ceramic composites

TiB₂-SiC and TiB₂-SiC-graphene nanoplatelets (GNPs) composites were prepared using field-assisted sintering technology at 2100 °C in argon atmosphere, and the influence of the SiC and different GNPs addition on microstructure development, mechanical and tribological properties has been investigated. Instrumented hardness, bending strength, chevron-notched fracture toughness and ball-on-flat tribological tests were used for the testing and characterization of the composites. The addition of SiC significantly improved the bending strength and elastic modulus with values of 601 MPa and 474 GPa, respectively, but decreased the fracture toughness with a value of 4.8 MPa.m^1/2. The addition of GNPs has a positive effect on fracture toughness and flexural strength but a negative one on the hardness. The increasing amount of both GNPs has a positive influence on wear characteristics of the composites thanks to the described wear mechanisms.     

Effect of fiber type on mechanical properties of short carbon fiber reinforced B4C composites

In order to enhance the mechanical properties of B₄C without density increase, the short carbon fibers M40, M55J and T700 reinforced B₄C ceramic composites were fabricated by hot-pressing process. The addition of the carbon fibers accelerates the densification of the B₄C, decreases their densities, and improves their strength and toughness. The enhancement effects of the three kinds of carbon fibers were studied by investigating the density, Vickers hardness and the mechanical properties such as flexural strength, flexural modulus and fracture toughness of the composites. The fiber type has a great influence on the mechanical properties and enhancement of the short carbon fiber reinforced B₄C composites. The flexible carbon fiber with high strength and low modulus such as T700 is appropriate to reinforce the B₄C matrix ceramic composites.     

Microstructure,mechanical properties and thermal conductivity of (Ti0.5Nb0.5)C–SiC composites

A series of (Ti_0.5Nb_0.5)C-x wt.% SiC (x = 0, 5, 10, 20) composites were prepared by spark plasma sintering. Dense microstructures with well‐dispersed SiC particles were obtained for all composites. With the increment of SiC content, the Vickers hardness, Young's modulus and fracture toughness increase monotonically. An optimized flexural strength of 706 MPa was achieved in (Ti_0.5Nb_0.5)C-5 wt.%SiC composite. (Ti_0.5Nb_0.5)C-20 wt%SiC composite exhibits the highest fracture toughness of 6.8 MPa m^1/2. The crack deflections and the suppression of grain growth were the main strengthening and toughening mechanisms. Besides, (Ti_0.5Nb_0.5)C-20 wt%SiC composite exhibit the highest thermal conductivity of 45 W/m·K at 800 °C.     

Mechanical behaviour of a low-clay translucent whiteware

A novel low-clay translucent whiteware body, using mostly non-plastic prefired materials and only a small amount of clay, was fabricated by slip casting and the effect of slip's solid content and sintering temperature on the mechanical behaviour was investigated. The degree of densification in the sintered specimens was determined by measuring the bulk density. The mechanical behaviour was determined by measuring the flexural strength and fracture toughness. Young's modulus and hardness were also measured. X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies were carried out to analyse the microstructure.The flexural strength and fracture toughness increase with both increasing the slip's solid content and the sintering temperature up to a certain level, but further increase in solid content and sintering temperature had an adverse effect on the properties. The maximum flexural strength (∼135 MPa) and fracture toughness (∼1.85 MPa m^1/2) values were attained with specimens produced from a slip having 45 vol.% solid content at a sintering temperature of 1350 °C. It was found that the amount and distribution of closed pores, their size and possible link with each other control the flexural strength and fracture toughness of the low-clay translucent whiteware.     

The formation and properties of Sialon-ZrN composites produced by reaction bonding combined with post gas-pressure sintering

Sialon-ZrN composites have been fabricated by a combination of reaction bonding and post-gas-pressure sintering. Composites with different amount of ZrN were post sintered at 1600, 1700 and 1800?°C under a nitrogen pressure of 0.7?MPa for 6?h. The results showed that mass loss due to decomposition increased with increasing sintering temperature. The mass loss at 1600 and 1700?°C was comparable, and below 3% even for the highest ZrN content of 50?wt%, but ranged between 6% and 9% for samples post sintered at 1800?°C with 10–50?wt% ZrN. Composites sintered at 1700?°C had the highest relative density (> 97%) and lowest open porosity (< 2%), and this was independent of ZrN content. The incorporation of the ZrN particles was observed to have an effect on the mechanical properties of the composites. The highest hardness (16.05?±?0.17?GPa) was observed for the composite sintered at 1700?°C with 20?wt% ZrN but decreased with higher ZrN contents, due to a weak bonding between the ZrN particles and the Sialon matrix. The fracture toughness showed a continuous increase with increasing ZrN content, due to the effect of the weak bonding on toughening mechanisms such as crack branching, crack deflection and crack bridging. The highest fracture toughness (5.35?±?0.18?MPa?m^1/2) was observed for the composited sintered at 1700?°C with 50?wt% ZrN.     

Silica‐filled polypropylene composites: The effect of ethylene diamine dilaurate and maleic anhydride grafted polypropylene on mechanical properties,water absorption,morphology, and thermal properties

The effect of two compatibilizers, i.e. ethylene diamine dilaurate (EDD) and maleic anhydride grafted polypropylene (MAPP) on the mechanical properties, water absorption, morphology, and thermal properties of silica‐filled polypropylene (PP/Sil) composites were studied. The results show that the tensile, impact and flexural strengths (up to 2 php), Young's modulus, and elongation at break (Eb) increased with increasing EDD content. However, increasing MAPP content increases the tensile strength, Young's modulus, impact and flexural strengths, and water absorption resistance. At a similar compatibilizer content, EDD exhibits higher Eb, impact and flexural strengths but lowers tensile strength, Young's modulus, and water absorption resistance compared with MAPP. Scanning electron microscopy study of tensile fractured surfaces exhibits the evidence of better silica‐PP adhesion with MAPP and EDD compared with the similar composites but without compatibilizer. Fourier transform infra red spectra provide an evidence of interaction between EDD or MAPP with PP/Sil composites. Termogravimetry analysis results indicate that the addition of EDD or MAPP slightly increases the thermal stability of PP/Sil composites. Differential scanning calorimetry also indicates that PP/Sil composites with EDD or MAPP have higher heat fusion (ΔH_f(com)) and crystallinity (X_com) than similar composites but without compatibilizer. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Effect of printing parameters on mechanical properties of extrusion-based additively manufactured ceramic parts

The purpose of this study is to investigate the effect of printing parameters on the physical and mechanical properties of additively manufactured ceramics (alumina and zirconia). Sample parts were obtained by extrusion-based additive manufacturing of a ceramic-binder mixture and subsequent post-processing (debinding and sintering). Their mechanical properties (microhardness, flexural strength, toughness) were measured and correlated with the printing parameters. Part orientation is the most significant factor for microhardness and flexural strength in both ceramic materials. Parts with vertical orientation show higher hardness while horizontal samples show higher flexural strength compared to their respective counterparts. Extrusion velocity was found to be insignificant for hardness and flexural strength. However, a marginal increase in fracture toughness with the increase in the extrusion velocity was observed. The fracture toughness of additively manufactured ceramics shows an increasing trend with elastic modulus and flexural strength and a decreasing trend with hardness and sintered density.     

Mechanical properties of oxynitride glasses

Oxynitride glasses combine a high refractoriness, with Tg typically >850°C, and remarkable mechanical properties in comparison with their parent oxide glasses. Their Young's modulus and fracture toughness reach 170 GPa and 1.4 MPa m^.5, respectively. Most reports show good linear relationships between glass property values and nitrogen content. There is a clear linear dependence of Young's modulus and microhardness on fractional glass compactness (atomic packing density). They also have a better resistance to surface damage induced by indentation or scratch loading. The improvements stem from the increase of the atomic network cross-linking—because of three-fold coordinated nitrogen—and of the atomic packing density, despite nitrogen being lighter than oxygen and the Si–N bond being weaker than the Si–O bond. For constant cation composition, viscosity increases by ∼3 orders of magnitude as ∼17 eq.% oxygen is replaced by nitrogen. For rare earth oxynitride glasses with constant N content, viscosity, Young's modulus, Tg, and other properties increase with increasing cation field strength (decreasing ionic radius). Research continues to find lighter, stiffer materials, including glasses, with superior mechanical properties. With higher elastic moduli, hardness, fracture toughness, strength, surface damage resistance, increased high temperature properties, oxynitride glasses offer advantages over their oxide counterparts.     

Enhancement mechanical properties of in-situ preparated B4C-based composites with small amount of (Ti3SiC2+Si)

B₄C-based composites were synthesized by spark plasma sintering using B₄C、Ti₃SiC₂、Si as starting materials. The effects of sintering temperature and second phase content on mechanical performance and microstructure of composites were studied. Full dense B₄C-based composites were obtained at a low sintering temperature of 1800 °C. The B₄C-based composite with 10 wt% (TiB₂+SiC) shows excellent mechanical properties: the Vickers hardness, fracture toughness, and flexural strength are 33 GPa, 8 MPa m^1/2, 569 MPa, respectively. High hardness and flexural strength were attributed to the high relative density and grain refinement, the high fracture toughness was owing to the crack deflection and uniform distribution of the second phase.     

Performance evaluation of basalt fiber-reinforced geopolymer composites with various contents of nano CaCO3

High carbon footprint of cement production is the major drawback of plain cement concrete resulting in environmental pollution. Geopolymer composites paste can be effectively used as an alternative to Portland cement in the construction industry for a sustainable environment. The demand for high-performance composites and sustainable construction is increasing day by day. Therefore, the present experimental program has endeavored to investigate the mechanical performance of basalt fiber-reinforced fly ash-based geopolymer pastes with various contents of nano CaCO₃. The content of basalt fibers was fixed at 2% by weight for all specimens while the studied contents of nano CaCO₃ were 0%, 1%, 2%, and 3%, respectively. The compressive strength, compressive stress-strain response, flexural strength, bending stress-strain response, elastic modulus, toughness modulus, toughness indices, fracture toughness, impact strength, hardness, and microstructural analysis of all four geopolymer composite pastes with varying contents of nano CaCO₃ using scanning electron microscopy (SEM) were evaluated. The results revealed that the use of 3% nano CaCO₃ in basalt fiber-reinforced geopolymer paste presented the highest values of compressive strength and hardness while the use of 2% nano CaCO₃ showed the highest values of flexural strength, impact strength, and fracture toughness of composite paste. The SEM results indicated that the addition of nano CaCO₃ improved the microstructure and provided a denser geopolymer paste by refining the interfacial zones and accelerating the geopolymerization reaction.