氧化锌贫矿提锌渣中铅和银的氯盐一步浸出

运用X射线衍射、扫描电镜和X射线能谱等分析手段,对山东某地深度氧化锌贫矿提锌后渣进行工艺矿物学特征分析可知,矿物中金属赋存状态复杂,属难选矿物。开发出氯盐一步法浸出铅和银的新工艺,考察反应温度、NaCl浓度、添加剂用量、液固比、HCl加入量和浸出时间对浸出过程的影响。结果表明:加入添加剂对铅的浸出率没有影响,但可以显著提高银的浸出率。条件试验研究得出最佳工艺条件如下:浸出温度90℃、NaCl浓度390 g/L、添加剂用量15 mL、液固比(质量比)7?1、HCl加入量3 mL、浸出时间3 h。在此最佳工艺条件下,铅的浸出率达到95%左右,银的浸出率达到90%左右。     

Recovery of valuable metals from zinc leaching residue by sulfate roasting and water leaching

Zinc leaching residue (ZLR), produced from traditional zinc hydrometallurgy process, is not only a hazardous waste but also a potential valuable solid. The combination of sulfate roasting and water leaching was employed to recover the valuable metals from ZLR. The ZLR was initially roasted with ferric sulfate at 640 °C for 1 h with ferric sulfate/zinc ferrite mole ratio of 1.2. In this process, the valuable metals were efficiently transformed into water soluble sulfate, while iron remains as ferric oxide. Thereafter, water leaching was conducted to extract the valuable metals sulfate for recovery. The recovery rates of zinc, manganese, copper, cadmium and iron were 92.4%, 93.3%, 99.3%, 91.4% and 1.1%, respectively. A leaching toxicity test for ZLR was performed after water leaching. The results indicated that the final residue was effectively detoxified and all of the heavy metal leaching concentrations were under the allowable limit.     

从模拟高放射废液中电化学回收钯和银

为从高放射废液(HLLW)中回收钯和银,采用循环伏安法和恒电位沉积法研究钯和银在模拟硝酸溶液中的电化学行为.利用扫描电子显微镜(SEM)和X射线衍射仪(XRD)观察沉积产物的形貌并分析其组成.结果表明,在单独电沉积银时亚硝酸根的生成促进银的溶解.当同时电沉积钯和银时,相同时间内更多金属被沉积,且沉积的银没有再出现溶解....     

氧压酸浸处理锌焙砂中浸渣的新工艺研究

锌焙砂一般采用中性-低酸-高酸三段浸出工序,该工艺在酸浸出中浸渣的过程中,铁也大量浸出进入到溶液中,加重了净化电积前除铁的负担。通过将传统锌湿法冶金工艺与氧压酸浸新工艺相结合,研究了氧压酸浸处理中浸渣的氧气压力、硫酸浓度、温度、浸出时间、粒度、液固比和分散剂等相关因素的影响。实验结果表明该工艺不仅提高了锌的浸出率（〉98％）,降低了铁的浸出率（〈50％）,缩短了生产周期,降低了生产成本,具有良好的经济效益;而且还具有环境友好和资源利用率高等优点,实现了简化工艺和节能减排的目的,为工业化生产提供了参考．     

锌浸渣还原焙烧-磁选回收铁

在查明锌浸渣工艺矿物学的基础上,采用还原焙烧将铁酸锌分解为氧化锌和磁性氧化铁,再通过磁选的方法回收铁,达到锌、铁分离的目的。实验考查了焙烧温度、焙烧时间、还原剂用量对铁酸锌分解率、铁回收率和铁品位的影响。结果表明:在焙烧温度为950℃、焙烧时间为1 h及还原剂添加量为10%和5%的条件下,铁酸锌分解率达到72.05%,铁回收率可达到91.79%,精矿中铁的品位为50%左右。焙烧及磁选过程中颗粒的团聚包裹是铁精矿品位不高的主要原因。     

从废旧锌锰电池中回收锌和锰的工艺研究

废旧锌锰干电池经过剖开、焙烧处理，去除汞和碳粉，再用硫酸浸取，滤液采用沉淀法分离锌和锰。锌和锰的回收率分别为94．5％和93．6％。     

Technological mineralogy and environmental activity of zinc leaching residue from zinc hydrometallurgical process

Chemical, physical, structural and morphological properties of zinc leaching residue were examined by the combination of various detection means such as AAS, XRF, XRD, Mössbauer spectrometry, SEM-EDS, TG-DSC, XPS and FTIR. The toxicity characteristic leaching procedure (TCLP) was used to investigate the environmental activity of zinc leaching residue for a short contact time. The phase composition analysis indicated that the zinc leaching residue mainly consists of super refined flocculent particles including zinc ferrite, sulfate and silicate. The physical structural analysis showed that it has a thermal instability and strong water absorption properties. The results of TCLP indicated that the amounts of Zn and Cd in the leaching solution exceed 40 and 90 times of limit, respectively, which demonstrate that this residue is unstable in weak acidic environment for a short contact time.     

锌粉置换回收锑精矿碱浸液中的金

锑精矿碱浸液是湿法处理锑精矿产生的中间产物含有少量的金，必须回收。以山东某公司锑精矿碱浸液为原料，经多种提取剂对比，采用锌粉置换回收其中的金。考察了锌粉用量、料液pH、浸出温度、时间的影响，得到的最佳工艺条件为:锌粉用量4.0 kg/m³，溶液pH=11，反应时间3 h，反应温度80 ℃，多批次试验金回收率88%。工艺过程简单，经济性可行，有效解决了资源浪费问题，为锑精矿碱浸液回收金提供了一条新的工艺。     

Ida~(2-)-H_2O体系浸出低品位氧化锌矿(英文)

采用Ida2--H2O体系(亚氨二乙酸盐水溶液)处理高碱性脉石型低品位氧化锌矿,考察浸出时间、液固比、配体总浓度、温度及pH值对矿物中主金属Zn及杂质元素Ca、Mg、Cu、Ni、Fe、Pb、Cd的溶出影响。结果表明:在弱碱性Ida2--H2O体系中,Ca、Mg、Fe不会被大量溶出,有价金属Cu、Ni、Pb、Cd可部分随主金属Zn溶出而进入浸出液;在浸出时间4h、液固比5:1、配体总浓度0.9mol/L、温度70℃、pH8的优化条件下,锌浸出率为76.6%。     

Ida~（2-）-H_2O体系浸出低品位氧化锌矿

采用Ida2--H2O体系（亚氨二乙酸盐水溶液）处理高碱性脉石型低品位氧化锌矿,考察浸出时间、液固比、配体总浓度、温度及pH值对矿物中主金属Zn及杂质元素Ca、Mg、Cu、Ni、Fe、Pb、Cd的溶出影响。结果表明：在弱碱性Ida2--H2O体系中,Ca、Mg、Fe不会被大量溶出,有价金属Cu、Ni、Pb、Cd可部分随主金属Zn溶出而进入浸出液;在浸出时间4h、液固比5：1、配体总浓度0.9mol/L、温度70℃、pH8的优化条件下,锌浸出率为76.6%。     

预浸-氰化浸出回收湿法炼锌渣中的银和金

某冶炼厂的锌浸出渣中银勘布粒度细,含银、金分别为381.3、1.02 g/t,可采用预浸-预浸渣氰化浸出工艺回收。重点研究了预浸条件对银、金浸出效率的影响。条件实验表明,药剂A比酸浸、氨浸具有更好的预浸效果;最佳预浸条件为药剂A浓度200 g/L、浸出液固比2:1、在50℃浸出3 h。综合条件实验得到的预浸渣渣率为66.2%,金、银的氰化浸出回收率分别为85.7%、92.9%。     

Selective recovery of zinc from zinc oxide dust using choline chloride based deep eutectic solvents

Deep eutectic solvents (DESs) are a kind of potential lixiviant for selective metal processing due to their versatile complexation properties. In this study, we investigated the recovery of zinc from zinc oxide dust using choline chloride−urea− ethylene glycol (ChCl−urea−EG) DESs. The zinc extraction efficiency can be up to 85.2% when the slurry concentration is 50 g/L, leaching temperature is 80 °C and stirring speed is 600 r/min. The leaching process is controlled by the diffusion and the corresponding activation energy is 32.1 kJ/mol. The resultant solution was directly used for the electrodeposition of zinc. The pure zinc deposit is obtained with a current efficiency of 82.6%. Furthermore, the ChCl−urea−EG DESs can be recycled. This approach is shown to be promising for the recycling of zinc from the zinc-containing dust.     

锌浸出渣中银的回收方法综述

湿法炼锌是当今世界炼锌主要方法,生产中所得锌浸渣中含有较多的锌及其他有价金属(如银、铅、铜、镉、铟、锗等),作为尾矿堆存不仅会占用大量的土地资源,而且还会造成资源的严重浪费,加之锌浸出渣的长期堆存环境危害性高,因此对锌浸出渣中的有价金属进行综合回收具有十分重要的意义。本文结合国内外锌浸出渣的研究状况,重点针对锌浸出渣中银的回收现状进行论述,全面阐述锌浸出渣中银的工艺矿物学性质、提取工艺流程及发展趋势,对该类资源的综合回收利用具有十分重要的借鉴作用。     

铁酸锌选择性还原及其在锌浸出渣处理中的应用

传统湿法炼锌过程产生大量富含有价金属资源的铁酸锌废渣,铁的分离是实现铁酸锌废渣中有价金属资源回收的关键。提出含大量铁酸锌的锌浸出渣选择性还原焙烧?浸出分离铁和锌的新方法。通过热力学分析确定铁酸锌分解过程中Fe3O4和ZnO产物的优势区域,并发现V(CO)/V(CO+CO2)比是控制铁酸锌还原焙烧产物物相的关键因素,在V(CO)/V(CO+CO2)比在2.68%?36.18%范围内,铁酸锌优先分解生成在Fe3O4和ZnO。通过TG分析,确定铁酸锌还原焙烧的最佳条件为焙烧温度700?750°C,CO体积分数6%,V(CO)/V(CO+CO2)30%。基于上述研究结果,对富含铁酸锌的锌浸渣进行还原焙烧处理,焙烧产物经酸浸后,锌的浸出率达70%,铁的浸出率仅为18.4%,实现锌浸渣中锌和铁的有效分离。     

回转窑内渣成分优化实现锌铅元素的高效回收（英文）

在回转窑内从高硅锌浸出渣中实现高效回收锌铅金属。XRD、SEM、EDS及ICP表征结果表明,浸出渣含12.4%SiO₂、16.1%Zn和7.4%Pb(质量分数)。热力学分析表明,在回转窑内1150～1250℃的冶炼环境下,锌浸出渣中极易产生锌和铅的金属蒸气。通过分析13种冶金渣成分的黏度及熔点,发现3种渣成分(47%SiO₂-23%CaO-30%FeO、40%SiO₂-28%CaO-32%FeO、40%SiO₂-30%CaO-30%FeO,质量分数)具有合适的物理特性,即熔点和黏度分别为1150～1280℃和0.2～0.5 Pa·s。工业实验表明,采用优化的渣成分,锌和铅的回收率分别高达97.3%和94.5%,冶炼后渣内锌和铅的含量分别低至0.51%和0.45%(质量分数)。水淬渣的国标浸出实验表明,浸出液中含1.82 mg/L Zn、～0.01 mg/L Cu、0.0004 mg/L As、～0.01 mg/L Cd、0.08 mg/L Pb和～0.02 mg/L Hg,证实锌浸出渣同步实现无害化...     

湿法炼锌净化渣酸浸的动力学

对湿法炼锌净化渣的浸出动力学进行了研究,并探讨了硫酸浓度、反应温度、粒度等对钴、锌浸出率的影响规律。从动力学的角度分析了整个浸出过程,得到优化条件：液固比50：1(mL/g),硫酸浓度100 g/L,反应温度70°C,粒度75~80μm,反应时间20 min。在此优化条件下钴的浸出率为99.8%,锌的浸出率为91.97%。结果表明：在硫酸体系中钴的浸出符合不生成固体产物层的“未反应收缩核”模型。通过 Arrhenius 经验公式求得钴和锌表观反应活化能分别为11.693 kJ/mol和6.6894 kJ/mol,这表明浸出过程受边界层扩散控制。     

湿法炼锌废渣中硫脲浸出银的动力学

探讨了从湿法炼锌废渣中用硫脲浸出回收银的浸出反应动力学,从这种难浸的含银炼锌废渣中用硫脲浸出回收银,浸出反应是一种典型的氧化还原反应并可充分进行,同时,通过动力学推导得出,从湿法炼锌废渣中用硫脲浸出银的反应动力学模型为收缩核动力学模型,同时计算出浸出活化能为13．26kJ/mol。该模型反映了浸出过程中控制整个反应速率的决定步骤是固膜扩散速率,并较好地说明了浸出机理。     

A study on comprehensive recycling of waste diamond tools

This article puts forward a new method of recycling materials in diamond tools comprehensively and efficiently by means of analyzing and summarizing various methods of recycling waste diamond tools.After the waste diamond tools were decomposed in a mixed acid,metals contained in it went into solution in their ionic forms,while diamond and tungsten carbide particles formed into residues to be reclaimed.The amounts of metal ions in the leaching solution were adjusted according to the contents of metals in the diamond tools;then,the leaching solution was co-precipitated using oxalic acid as precipitation agent,and ammonia water was added to adjust the pH value of the oxalic acid.Under the right conditions,the comprehensive precipitation rate of metals reached above 98%.Finally,ultrafine pre-alloy powder was obtained by hydrogen reduction of oxalate.