多单体接枝聚丙烯对干态和湿态玻纤增强尼龙6性能的影响

通过熔融共混法,加入自制的多单体接枝聚丙烯(PP-g-MAH-EP)制备尼龙6(PA6)/玻璃纤维(GF)/PP-g-MAH-EP复合材料。研究了PP-g-MAH-EP对复合材料吸水前后静态和动态力学性能的影响,并通过扫描电镜与原子力显微镜分析试样断面微观形貌及微观力学性质的变化。结果表明,PA6/GF/PP-g-MAH-EP复合材料的吸水率随着PP-g-MAH-EP含量的增加逐渐降低,即PP-g-MAH-EP的加入能有效抑制PA6/GF复合材料的吸水率;在干态及相同吸水条件下,PA6/GF/PP-g-MAH-EP复合材料的力学性能明显优于PA6/GF。与PA6/GF相比,当PP-g-MAH-EP加入20 phr时,复合材料综合力学性能最好。PP-g-MAH-EP的加入,有效改善了纤维与尼龙6基体界面的粘接,吸水后的基体树脂在探针作用下的形变量明显降低。     

Effect of Seawater and Warm Environment on Glass/Epoxy and Glass/Polyurethane Composites

A study of the durability of fiber reinforced polymer (FRP) materials in seawater and warm environment is presented in this paper. The major objective of the study is to evaluate the effects of seawater and temperature on the structural properties of glass/epoxy and glass/polyurethane composite materials. These effects were studied in terms of seawater absorption, permeation of salt and contaminants, chemical and physical bonds at the interface, degradation in mechanical properties, and failure mechanisms. Test parameters included immersion time, ranging from 3 months to 1 year, and temperature including room temperature and 65°C. Seawater absorption increased with immersion time and with temperature. The matrix in both composites was efficient in protecting the fibers from corrosive elements in seawater; however moisture creates a dual mechanism of stress relaxation—swelling—mechanical adhesion, and breakdown of chemical bonds between fiber and matrix at the interface. It is observed that high temperature accelerates the degradation mechanism in the glass/polyurethane composite. No significant changes were observed in tensile strength of glass/epoxy and in the modulus of both glass/epoxy and glass/polyurethane composites. However, the tensile strength of the glass/polyurethane composite decreased by 19% after 1 year of exposure to seawater at room temperature and by 31% after 1 year of exposure at 65°C. Plasticization due to moisture absorption leads to ductile failure in the matrix, but this can be reversed in glass/polyurethane composites after extended exposure to seawater at high temperature where brittle failure of matrix and fiber were observed.     

天然细菌纤维素增强不饱和聚酯树脂复合材料的制备及性能

将天然纤维-细菌纤维素（BC）作为增强材料加入不饱和聚酯树脂（UPR）基体中,采用RTM工艺制备BC/UPR复合材料,并对其力学性能、吸湿性能进行了研究。通过紫外辐照方法探讨了BC/UPR复合材料的降解性能。研究结果表明:通过对细菌纤维素的表面改性,在亲水性的天然纤维和疏水性的高聚物基体之间形成了化学键结合,提高了BC/UPR复合材料的力学性能;BC纤维体积分数的增加也有助于提高力学性能, 当纤维体积分数为20%时,该复合材料拉伸强度最高可达152.9MPa; BC/UPR复合材料的吸湿过程符合Fick定律,吸湿可导致力学性能下降; BC/UPR复合材料吸收光能后,表面含氧官能团数量增加,发生一定程度的光降解。      

激光改性纤维对其增强环氧树脂复合材料力学性能的影响

利用激光对玻璃纤维、玄武岩纤维和碳纤维进行表面改性后,以环氧树脂为基体,分别制备三种纤维增强环氧树脂复合材料。利用SEM和万能试验机对表面改性前后的碳纤维形态、力学性能及三种纤维/环氧树脂复合材料的力学性能和断面形貌进行表征,研究了纤维激光表面改性对三种纤维及其增强环氧树脂复合材料力学性能的影响。结果表明:激光表面改性对碳纤维/环氧树脂复合材料的力学性能提升最高,其拉伸强度最大提高了77.06%,冲击强度最大提高了31.25%,玄武岩纤维/环氧树脂复合材料的力学性能提升次之,而玻璃纤维/环氧树脂复合材料的力学性能有所下降。因此,激光进行表面改性适用于碳纤维和玄武岩纤维。     

聚对苯二甲酸乙二醇酯/锡氟磷酸盐玻璃复合材料原位成纤对聚丙烯的增强效果

采用低玻璃化转变温度的锡氟磷酸盐玻璃(Pglass)改性聚对苯二甲酸乙二醇酯(PET),制备低黏度高模量的PET基复合材料(PET/Pglass);以PET/Pglass或PET为成纤相,聚丙烯为基体,利用实验室自主设计的多级拉伸挤出装置,制得原位成纤增强聚丙烯复合材料,并研究成纤相形态及其对复合材料力学性能的影响。结果表明,与PET相比,PET/Pglass在多级拉伸挤出过程中原位成纤更容易,纤维长径比更大,分散更均匀,从而进一步提高聚丙烯的拉伸强度和模量,而且能保持聚丙烯较高的断裂伸长率,表明具有低黏高模的PET/Pglass对聚丙烯的原位成纤增强效果更显著。     

Influence of fiber content on the mechanical and dynamic mechanical properties of glass/ramie polymer composites

The combination of glass and ramie fibers with a polyester matrix can produce a hybrid material that is competitive to all glass composites (e.g. those used in the automobile industry). In this work, glass and ramie fibers cut to 45 mm in length were used to produce hybrid polymer composites by resin transfer molding (RTM), aiming to evaluate their physical, mechanical and dynamic mechanical properties as a function of the relative glass–ramie volume fractions and the overall fiber content (10, 21 and 31 vol.%). Higher fiber content and higher ramie fiber fraction in the hybrid composites yielded lower weight composites, but higher water absorption in the composite. The mechanical properties (impact and interlaminar shear strength) of the composites were improved by using higher fiber content, and the composite with 31 vol.% of reinforcement yielded the lowest value for the reinforcement effectiveness coefficient C, as expected. Although the mechanical properties were improved for higher fiber content, the glass transition temperature did not vary significantly. Additionally, as found by analyzing the adhesion factor A, improved adhesion tended to occur for the composites with lower fiber content (10%) and higher ramie fiber fraction (0:100) and the results for the adhesion factor A did not correspond to those found by the analysis of the tan delta peak height.     

Green composites from a conjugated linseed oil-based resin and wheat straw

Green composites have been prepared using a free radically cured conjugated linseed oil-based resin reinforced with wheat straw. The effect of the amount of the wheat straw; the size of the wheat straw fiber; the matrix crosslink density; the incorporation of a compatibilizer, maleic anhydride; and the molding pressure on the structure, water absorption, and thermal and mechanical properties of the composites has been investigated. In general, increasing the amount of the wheat straw, the crosslink density of the matrix, and the molding pressure leads to improved thermal and mechanical properties. By using maleic anhydride as a compatibilizer, significant improvements in the mechanical properties can be achieved. Results from water uptake experiments indicate that the amount and fiber size of the wheat straw are the major factors influencing the absorption of water in the composite. The composites prepared are composed of 75–95 wt.% renewable materials and most have properties suitable for industrial applications.     

CIP/GF/CF/EP吸波复合材料的制备及力学性能

为制备兼具力学性能和电磁吸收性能的结构型吸波材料,采用真空辅助成型工艺设计制备一种以羰基铁粉(CIP)为吸收剂,玻璃纤维(GF)为透波层,碳纤维(CF)为反射层,环氧树脂(EP)为基体的吸波复合材料。研究了不同质量比CIP/EP对吸波复合材料力学性能和微波吸收性能的影响。通过FTIR和DSC分析可知CIP未与EP发生化学反应。SEM结果表明CIP能够在EP树脂基体中均匀分散,不趋向于纤维表面。力学测试分析结果显示:当CIP/EP质量比达到30%时,CIP/GF/CF/EP复合材料的力学性能最佳,拉伸强度为347.56MPa,拉伸模量为25.99GPa,较纯GF/CF/EP复合材料提升了4.3%和5.7%;弯曲强度为339.6MPa,弯曲模量为23.7GPa,较纯GF/CF/EP复合材料提升了18.2%和71.2%。矢量网络分析可知复合吸波板的吸波性能随CIP含量的增加而增加,且吸波损耗反射峰值朝低频段移动。     

云母和纤维组合增强聚丙烯复合材料Ⅰ.力学性能研究

以云母填充聚丙烯为基体,连续无规玻璃纤维毡为增强材料,通过双钢带压机制成了云母填充ＧＭＴ（Ｇｌａｓｓ Ｍａｔ Ｒｅｉｎｆｏｒｃｅｄ Ｔｈｅｒｍｏｐｌａｓｔｉｃ）．研究了云母的加入对 ＧＭＴ力学性能的影响,结果表明,少量云母的加入,使ＧＭＴ的力学性能发生明显变化,强度和刚性显著提高,云母和纤维表现出正的组合效应;随着云母填充量增加,ＧＭＴ的强度和模量下降,云母与纤维的组合表现出负效应,云母对ＧＭＴ力学性能的影响主要与云母的加入引起的玻璃纤维与聚丙烯基体之间的界面结合有关,少量云母的加入使玻璃纤维与基体的界面结合强度提高,而大量云母的加入则造成纤维与基体界面结合强度下降,向基体中添加马来酸酐接枝聚丙烯（ＭＰＰ）,能有效改善在云母含量较高情况下纤维与基体的界面结合状况,使高填充云母ＧＭＴ表现出优良的力学性能　还研究了云母粒径对云母填充ＧＭＴ力学性能的影响,     

浸泡腐蚀对玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料弯曲性能的影响

制备了不同纤维质量分数的玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料。通过三点弯曲试验研究了纤维质量分数对复合泡沫材料力学性能的影响。将复合泡沫材料试件置于蒸馏水和海水中浸泡,研究了浸泡腐蚀对试件弯曲性能的影响,并结合扫描电镜照片分析其原因。研究表明:纤维质量分数越高,玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料的吸湿率越大,且在蒸馏水中的吸湿率较海水中的更大。试件的弯曲强度随纤维质量分数增加而增大,当纤维质量分数为10%时达到最大,比未添加纤维的试件增强了51%,之后则随纤维质量分数增加逐渐降低。浸泡腐蚀降低了试件的弯曲性能,其中海水浸泡后的试件弯曲性能最低。玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料弯曲强度降低的直接原因是浸泡腐蚀使得部分玻璃微珠和玻璃纤维与环氧树脂基体间的界面层受到破坏。     

Analysis of Mechanical Properties of Injection Molded Short Glass Fibre (SGF)/Calcite/ABS Composites

Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) and sized short-glass fibres with two amino-silane coupling agents.The calcite particle content is 0, 11.7 and 23.5 vol. pct for the matrices. The glass fiber contentis 0, 10 and 15 vol. pct. The matrix materials and corresponding composites were compoundedusing a twin screw extruder and dumbbell-shaped tensile bars were prepared with an injectionmolding process. The tensile and flexural properties as well as the unnotched and notchedCharpy impact energies of short glass fibre/calcite/ABS composites were studied in this paper.The effects of fibres, fibre surface treatments and particles on these mechanical properties ofthe composites were discussed in detail. An importarit information was obtained, which is thatthe tensile and flexural strengths of hybrid SGF/calcite/ABS composites are the same as thoseof corresponding fibre composites when the ratio of the interfacial adhesion strength betweenparticles and matrix to that between fibres and matrix is higher than certain value. otherwise theformer are lower than the latter.     

偶联剂对玻璃纤维增强淀粉/聚乳酸复合材料性能的影响

分别以马来酸酐、KH550、KH560和KH570为偶联剂对玻璃纤维进行预处理,再与淀粉、聚乳酸(PLA)复合,通过熔融挤出法制备玻璃纤维增强淀粉/PLA复合材料。研究了偶联剂种类对玻璃纤维增强复合材料熔融指数、力学性能、热性能和熔融流变性能的影响。实验发现马来酸酐、KH550、KH570、KH560处理玻璃纤维增强淀粉/PLA复合材料的熔融指数和力学性能都依次增大,表明KH560处理玻璃纤维增强淀粉/PLA复合材料的界面黏结作用最强。对热性能进行表征发现,马来酸酐、KH550、KH570、KH560处理玻璃纤维增强淀粉/PLA复合材料玻璃化转变温度、重结晶温度、结晶度和热稳定性均依次提高。受玻璃纤维与淀粉/PLA基体界面黏结效果的影响,马来酸酐、KH550、KH570、KH560处理玻璃纤维增强淀粉/PLA体系的储能模量和复数黏度依次增大。     

Tamarind Fruit Fiber and Glass Fiber Reinforced Polyester Composites

Polyester-based hybrid composites were developed by combining the tamarind fruit (Tf) and glass fibers into a polyester matrix. Hardness, impact strength, frictional coefficient, and chemical resistance of hybrid composites with and without alkali treatments were studied. Variation of the aforementioned mechanical properties and chemical resistance was studied with different fiber lengths, such as 1, 2, and 3 cm. A 9 vol% of the tamarind and glass fibers was reinforced into the polyester matrix. The aforementioned mechanical properties were optimally improved at 2-cm fiber length when compared with 1- and 3-cm fiber lengths. Chemical resistance was also significantly improved for all chemicals except toluene. A 3°C rise in decomposition temperature while a 2°C rise in glass transition temperature was observed from TGA and DSC micrograms, respectively.     

Carbon and glass hierarchical fibers: Influence of carbon nanotubes on tensile,flexural and impact properties of short fiber reinforced composites

Dense carbon nanotubes (CNTs) were grown uniformly on the surface of carbon fibers and glass fibers to create hierarchical fibers by use of floating catalyst chemical vapor deposition. Morphologies of the CNTs were investigated using scanning electronic microscope (SEM) and transmission electron microscope (TEM). Larger diameter dimension and distinct growing mechanism of nanotubes on glass fiber were revealed. Short carbon and glass fiber reinforced polypropylene composites were fabricated using the hierarchical fibers and compared with composites made using neat fibers. Tensile, flexural and impact properties of the composites were measured, which showed evident enhancement in all mechanical properties compared to neat short fiber composites. SEM micrographs of composite fracture surface demonstrated improved adhesion between CNT-coated fiber and the matrix. The enhanced mechanical properties of short fiber composites was attributed to the synergistic effects of CNTs in improving fiber–matrix interfacial properties as well as the CNTs acting as supplemental reinforcement in short fiber-composites.     

湿热老化对玻璃纤维/环氧树脂复合材料性能的影响

为研究玻璃纤维(GF)/环氧树脂复合材料湿热老化机制, 首先, 利用称重法、动态热机械分析仪(DMA)、SEM和矢量网络介电分析仪研究了湿热老化对GF/环氧树脂608(EP608)复合材料性能的影响;然后, 分析了复合材料的吸湿率、力学性能、介电性能与老化时间的关系, 并对其老化机制进行了探讨。结果表明:随老化时间延长, GF/EP608复合材料的力学性能和介电性能均有不同程度的下降;湿热老化对GF/EP608复合材料吸湿率的影响符合Fickian扩散定律;树脂基体的塑化、水解和基体-纤维界面的破坏是造成GF/EP608复合材料力学性能和介电性能下降的主要因素。所得结论可为GF增强环氧树脂基复合材料的应用提供科学依据。      

A micromechanical model for the mechanical degradation of natural fiber reinforced composites induced by moisture absorption

This paper develops a micromechanical model to study the mechanical degradation of natural fiber reinforced composites (NFRCs) induced by moisture absorption. Since the moisture absorption and the mechanical degradation of the composite are correlated, a modified Mori–Tanaka method with a damage variable is proposed. A set of micromechanical equations are established to describe the modulus loss of NFRCs. After specifying this model with different inclusion shapes, the overall swelling deformation and the mechanical degradation of the randomly oriented and the unidirectional straight natural fiber reinforced composites are studied in detail. Theoretical predicted results of the randomly oriented straight fiber reinforced composite are compared with experimental ones from literature and a good agreement is obtained. Further numerical results demonstrate that a stiffer matrix can reduce both the moisture absorption and the mechanical degradation of natural fibers.     

酰胺链硅烷界面结合剂对尼龙66/玻纤复合材料性能的影响

采用熔融挤出共混制备了尼龙66(PA66)/玻璃纤维(GF)复合材料,比较了常用硅烷偶联剂KH550与不同有机酸封端的酰胺链硅烷界面结合剂(ASI)对复合材料的力学性能、动态力学性能及界面层结构的影响,探究了复合材料中界面层形成的机理。结果表明,ASI与玻纤表面反应发生了化学反应,ASI添加量为1.5%时,对PA66/GF复合材料的力学性能改善效果最明显,其中,以对苯二甲酸封端,相对分子质量为2000左右的PTA-ASI使PA66/GF复合材料的界面能力提升最高,拉伸强度提高了54.8%,复合材料的综合性能提高最为显著。     

玻璃纤维含量对竹粉/高密度聚乙烯复合材料性能的影响

为利用玻璃纤维提高木塑复合材料的综合性能,探讨玻璃纤维含量对竹粉/高密度聚乙烯(HDPE)复合材料性能的影响规律,首先,采用A-171硅烷偶联剂对竹粉表面进行了改性,并加入了一定量的玻璃纤维;然后,采用热压成型工艺制备了玻璃纤维-竹粉/HDPE复合材料;最后,考察了玻璃纤维含量对复合材料力学性能、热学性能及摩擦学性能的影响,并利用SEM观察材料的断面和磨损表面形貌。结果表明:当玻璃纤维含量为3wt%时,能显著提高竹粉/HDPE复合材料的拉伸强度和弯曲强度,与未添加玻璃纤维的复合材料相比,添加玻璃纤维后复合材料的拉伸强度和弯曲强度分别提高了19.41%和23.54%;在30~60℃温度范围内,复合材料长度-宽度方向上的线膨胀系数随着玻璃纤维含量的增加而明显减小,而同一复合材料的线膨胀系数随温度的升高而逐步增大;在氮气气氛下,随玻璃纤维含量的增加,竹粉/HDPE复合材料的摩擦系数先逐渐增大,而后基本保持不变,磨损率逐渐减小。所得结论显示玻璃纤维含量为3wt%~7wt%的木塑产品适用于建筑横梁(如凉亭或桥梁等),而玻璃纤维含量为7wt%~10wt%的木塑产品适用于高人流量场所(如公园或休闲绿道等)的地面铺装。      

废旧线路板粉料/玻璃纤维增强复合材料研制

以废旧线路板回收处理过程中得到的塑料粉料与玻璃纤维作为增强材料,采用模压成型的方法制备成不饱和聚酯复合材料。研究了模压工艺参数以及废弃物粉末填料配比等对复合材料力学性能的影响规律,并初步展望了废弃物复合材料的应用。结果表明,随着模压温度、压强、模压时间和填料含量的增加,复合材料的弯曲强度先升高后降低;在优化的模压工艺参数条件下,用废弃粉体与短切玻璃纤维作为组合增强体,制得的不饱和聚酯复合材料的力学性能远大于仅用废弃粉体作为增强体的力学性能,其弯曲强度和冲击强度可达150MPa、18kJ/m2。     

Biocomposites from Musa textilis and polypropylene: Evaluation of flexural properties and impact strength

Abaca (Musa textilis)-reinforced polypropylene composites have been prepared and their flexural mechanical properties studied. Due to their characteristic properties, M. textilis has a great economic importance and its fibers are used for specialty papers. Due to its high price and despite possessing very distinctive mechanical properties, to date abaca fibers had not been tested in fiber-reinforced composites. Analysis of materials prepared showed that, in spite of reduced interface adhesion, flexural properties of the PP composites increased linearly with fiber content up to 50 wt.%. Addition of a maleated polypropylene coupling agent still enhanced the stress transfer from the matrix to the reinforcement fiber. As a result, composites with improved flexural properties were obtained. The mechanical properties of matrix and reinforcing fiber were evaluated and used for modelling both the flexural strength and modulus of its composites. In addition, the impact strength of materials was evaluated. Comparison with mechanical properties of composites reinforced with fiberglass points out the potentiality of abaca-reinforced polypropylene composites as suitable substitutes in applications with low impact strength demands.