Preparation of surface modified zinc oxide nanoparticle with high capacity dye removal ability

In this paper, the surface modification of zinc oxide nanoparticle (ZON) by amine functionalization was studied to prepare high capacity adsorbent. Dye removal ability of amine-functionalized zinc oxide nanoparticle (AFZON) and zinc oxide nanoparticle (ZON) was also investigated. The physical characteristics of AFZON were studied using Fourier transform infrared (FTIR), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Acid Blue 25 (AB25), Direct Red 23 (DR23) and Direct Red 31 (DR31) were used as model compounds. The effect of operational parameters such as dye concentration, adsorbent dosage, pH and salt on dye removal was evaluated. The isotherm and kinetic of dye adsorption were studied. The maximum dye adsorption capacity (Q₀) was 20 mg/g AB25, 12 mg/g DR23 and 15 mg/g DR31 for ZON and 1250 mg/g AB25, 1000 mg/g DR23 and 1429 mg/g DR31 for AFZON. It was found that dye adsorption followed Langmuir isotherm. Adsorption kinetic of dyes was found to conform to pseudo-second order kinetics. Dye desorption tests (adsorbent regeneration) showed that the maximum dye release of 90% AB25, 86% for DR23 and 90% for DR31 were achieved in aqueous solution at pH 12. Based on the data of the present investigation, it can be concluded that the AFZON being an adsorbent with high dye adsorption capacity might be a suitable alternative to remove dyes from colored aqueous solutions.     

Induction of hydroxycarbonate apatite formation on polyethylene or alumina substrates by spherical vaterite particles deposition

Hydroxycarbonate apatite (HCA) layers were formed on polyethylene (PE) or alumina substrates by depositing spherical sub-micron vaterite particles and then immersing in simulated body fluid (SBF). HCA formation on vaterite‐coated PE was faster than that on coated alumina (3 days for PE and 7 days for alumina). The adsorption of phosphate ions on the vaterite particles in SBF was studied by monitoring changes in the concentration of phosphorous in SBF and the surface charges of vaterite during the SBF immersion. The phosphorous concentration of SBF in which a vaterite-coated PE was immersed for 1 h was lower than that in which a vaterite-coated alumina was immersed. Zeta potential of the vaterite surface deposited on PE drastically decreased after 1 h immersion in SBF. The vaterite particles deposited on each substrate immediately adsorbed phosphate ions in SBF. The amount of ions adsorbing on the vaterite surfaces deposited on PE was larger than that on alumina. This was attributed to differences in the surface charges between PE (? 16 mV) and alumina (+ 38 mV). The phosphate adsorption was predominantly electrostatic therefore related to the surface charge of vaterite particles. The surface charges of substrates may affect the charge of vaterite particles.     

Bioactivity of calcium phosphate coatings prepared by electrodeposition in a modified simulated body fluid

The purpose of this study was to investigate bioactivity of calcium phosphate coatings prepared by electrodeposition in a modified simulated body fluid (SBF). Calcium phosphates were electrodeposited on commercially pure titanium substrates in the modified SBF at 60 °C for 1 h maintaining the cathodic potentials of − 1.5 V, − 2 V, and − 2.5 V (vs. SCE). Subsequently, the calcium phosphate coatings were transformed into apatites during immersion in the SBF at 36.5 °C for 5 days. The apatites consisted of needle-shaped crystallites distributed irregularly with different grain sizes. As the coatings were electrodeposited at higher cathodic potential, the crystallite of the apatites got denser and the grain sizes of the apatites became bigger during subsequent immersion in the SBF. However, as the coatings were electrodeposited at higher cathodic potential, the coatings were transformed into apatites with lower crystallinity and the Ca/P atomic ratio of the apatites got higher than 1.67, that of stoichiometric hydroxyapatite, after subsequent immersion in the SBF. In addition, CO₃²⁻ ions contained in the modified SBF were incorporated in the calcium phosphate coating during electrodeposition and had an influence on transforming the calcium phosphate into bonelike apatite during subsequent immersion in the SBF showing that CO₃²⁻ incorporated in the apatites disturbed crystallization of the apatites. These results revealed that the coating electrodeposited at − 2.0 V (vs. SCE) in the modified SBF containing CO₃²⁻ ions was the most bioactive showing transformation into carbonate apatite similar to bone apatite.     

Characterization of a calcium phosphate–TiO2 nanotube composite layer for biomedical applications

Well-ordered nanotube arrays of titania ~ 0.7 μm high and about 40 or 110 nm in diameter were prepared via electrochemical oxidation at constant voltage (10, 15, 20 or 25 V) in a mixture of 0.86 wt.% of NH₄F, glycerol and deionized water. The effect of annealing the nanotubes at 600 °C on their morphology and structure was examined using SEM and TEM techniques. These substrates are suitable supports for a calcium phosphate coating deposited by a simple immersion in Hank solution.The nucleation and growth of a calcium phosphate (Ca–P) coating deposited on TiO₂ nanotubes (NT) from Hanks' solution was investigated using SEM. XPS and FTIR surface analytical techniques were used to characterize the self-organized porous TiO₂ layers covered with calcium phosphate coatings before and after protein adsorption. Our results confirm that the nanotubular titania layer became stable after annealing at 600 °C, while its internal structure changed from amorphous to crystalline anatase, and eventually, a mixture of anatase and rutile. These thermally stabilized TiO₂ nanotubes significantly enhance apatite formation in Hanks' Balanced Salt Solution as compared to pure Ti covered with a native oxide layer. The Ca–P/TiO₂ NT/Ti surface adsorbs a higher amount of protein (bovine serum albumin, BSA) for a geometric surface area than does the Ti surface. The above difference in protein adsorption suggests a more promising initial cellular response for a Ca–P/TiO₂ NT/Ti composite than for a typical Ti implant surface.     

Investigation of UV-photon induced hydrophilicity of titanium ion-implanted soda-lime silicate glasses

The UV-induced wetting effect on titanium oxide surface is well-known; however, the UV-induced hydrophilicity of titanium implanted soda-lime silicate glass has not been investigated. Hence the contact angle of water droplet under the indoor fluorescent lights on titanium-ion implanted soda-lime silicate glasses was investigated. The silicate glasses were implanted by MEVVA ion implanter by 40 keV titanium ions with a fluence of 10¹⁵ ions cm^?2. The contact angle, the chemical bonding environment, and surface morphologies were examined. Results show the formation of TiO₂, the increase of surface roughness, and the reduction of the contact angle after the ion implantation. Further enhancement of hydrophilicity after the 254 nm pre-UV irradiation for 1 h on the implanted sample surface was observed. The enhancement of the wetting effect after ion implantation could be attributed to rougher TiO₂ content surface. However, according to the mechanisms of UV photo-induced hydrophilicity on TiO₂ proposed previously, the enhancement of hydrophilicity of titanium implanted surface with and without 254 nm pre-photon radiation can be attributed to not only the reduction of hydrocarbon on surface during the UV radiation but also to the oxygen vacancies produced by 254 nm UV photon irradiation.     

Pulsed electrodeposition for the synthesis of strontium-substituted calcium phosphate coatings with improved dissolution properties

Strontium-substituted calcium phosphate coatings are synthesized by pulsed electrodeposition on titanium alloy (Ti6Al4V) substrates. Experimental conditions of the process are optimized in order to obtain a coating with a 5% atomic substitution of calcium by strontium which corresponds to the best observations on the osteoblast cells activity and on the osteoclast cells proliferation. The physical and chemical characterizations of the obtained coating are carried out by scanning electron microscopy associated to energy dispersive X-ray spectroscopy (EDXS) for X-ray microanalysis and the structural characterization of the coating is carried out by X-ray diffraction. The in vitro dissolution/precipitation properties of the coated substrates are investigated by immersion into Dulbecco's Modified Eagle Medium (DMEM) from 1 h to 14 days. The calcium, phosphorus and strontium concentrations variations in the biological liquid are assessed by Induced Coupled Plasma - Atomic Emission Spectroscopy for each immersion time. The results show that under specific experimental conditions, the electrodeposition process is suitable to synthesize strontium-substituted calcium phosphate coatings. Moreover, the addition of hydrogen peroxide (H₂O₂) into the electrolytic solution used in the process allows us to observe a control of the strontium release during the immersion of the prosthetic materials into DMEM.     

Bacterial adhesion studies on titanium,titanium nitride and modified hydroxyapatite thin films

A qualitative study on adhesion of the oral bacteria Porphyromonas gingivalis on titanium (Ti), titanium nitride (TiN), fluorine modified hydroxyapatite (FHA) and zinc modified FHA (Zn-FHA) thin films is investigated. Ti and TiN thin films were deposited by DC magnetron sputtering and hydroxyapatite-based films were prepared by solgel method. The crystalline structure, optical characteristics, chemical composition and surface topography of the films were studied by XRD, optical transmission, XPS, EDAX and AFM measurements. The predominant crystallite orientation in the Ti and TiN films was along (002) and (111) of hcp and cubic structures, respectively. The Ti : O : N composition ratio in the surface of the Ti and TiN films was found to be 7 : 21 : 1 and 3 : 8 : 2, respectively. The atomic concentration ratio (Zn + Ca) / P in Zn-FHA film was found to be 1.74 whereby the Zn replaced 3.2% of Ca. The rough surface feature in modified HA films was clearly observed in the SEM images and the surface roughness (rms) of Ti and TiN films was 2.49 and 3.5 nm, respectively, as observed using AFM. The film samples were sterilized, treated in the bacteria culture medium, processed and analyzed using SEM. Surface roughness of the films was found to have least influence on the bacterial adhesion. More bacteria were observed on the TiN film with oxide nitride surface layer and less number of adhered bacteria was noticed on the Ti film with native surface oxide layer and on Zn-FHA film.     

In vitro bioactivity evaluation of nano- and micro-crystalline anodic TiO2: HA formation,cellular affinity and organ culture

Anodization is an easily viable technique useful for producing TiO₂ coatings on titanium substrates. Nano-crystalline anodic TiO₂ structure was produced on titanium at 20 V using 1 M Na₂SO₄ and 0.5% NaF and consolidated by a further heat-treatment. Micro-crystalline anodic TiO₂ was produced on titanium by applying a galvanostatic current density of 70 A/m² in water medium. To assess the usefulness of these nano- and micro-oxides for bone implant stability, physical properties and bone in vitro bioactivity including HA formation, cellular affinity and mouse-tissue morphogenesis, were evaluated. Bioactivity of the different anodic surfaces was evaluated by treating them in a simulated body fluid (SBF) to form hydroxyapatite (HA) and the rates of HA formation were compared. Deposits of HA could be seen on the nano-oxide surface within 7 days, whereas HA was detected only after 14 days on the micro-oxide surface. In vitro cell culture tests done using mouse osteoblasts indicated that the nano-oxides showed statistically significant cell activity than the micro-oxides and the machined titanium. Branching morphogenesis test done for 72 h on these surfaces showed more branching on the micro- and nano-oxides as compared with titanium surface.     

Preparation and characterization of vanadia–titania mixed oxide for immobilization of Serratia rubidaea CCT 5732 and Klebsiella marcescens bacteria

Vanadia–titania mixed oxide was synthesized by sol–gel method and characterized by several techniques. Texturally, it is formed by mesopores and presents high-specific surface area and controlled porosity. Scanning electron microscopy revealed that vanadium is homogeneously distributed in the material. Structurally, it was possible to identify characteristic VO stretching bands by IR. The analysis of X-ray diffraction showed that the material, particularly vanadium, is highly dispersed. Application experiments were carried out through the immobilization of Serratia rubidae CCT 5732 and Klebsiella marcescens bacteria by adsorption on the surface of mixed oxide. The micrographies revealed that the bacteria were adsorbed on the entire support, with average surface densities of 8.55 × 10¹¹ cells/m² (Serratia rubidae CCT 5732) and 3.40 × 10¹¹ cells/m² (K. marcescens).     

Nanostructured severe plastic deformation processed titanium for orthodontic mini-implants

Titanium mini-implants have been successfully used as anchorage devices in Orthodontics. Commercially pure titanium (cpTi) was recently replaced by Ti-6Al-4 V alloy as the mini-implant material base due to the higher strength properties of the alloy. However, the lower corrosion resistance and the lower biocompatibility have been lowering the success rate of Ti-6Al-4 V mini-implants. Nanostructured titanium (nTi) is commercially pure titanium that was nanostructured by a specific technique of severe plastic deformation. It is bioinert, does not contain potentially toxic or allergic additives, and has higher specific strength properties than any other titanium applied in medical implants. The higher strength properties associated to the higher biocompatibility make nTi potentially useful for orthodontic mini-implant applications, theoretically overcoming cpTi and Ti-6Al-4 V mini-implants. The purposes of the this work were to process nTi, to mechanically compare cpTi, Ti-6Al-4 V, and nTi mini-implants by torque test, and to evaluate both the surface morphology and the fracture surface characteristics of them by SEM. Torque test results showed significant increase in the maximum torque resistance of nTi mini-implants when compared to cpTi mini-implants, and no statistical difference between Ti-6Al-4 V and nTi mini-implants. SEM analysis demonstrated smooth surface morphology and transgranular fracture aspect for nTi mini-implants. Since nanostructured titanium mini-implants have mechanical properties comparable to titanium alloy mini-implants, and biocompatibility comparable to commercially pure titanium mini-implants, it is suggestive that nanostructured titanium can replace Ti-6Al-4 V alloy as the material base for mini-implants.     

Folate targeted PEGylated titanium dioxide nanoparticles as a nanocarrier for targeted paclitaxel drug delivery

A novel titanium dioxide nanocarrier was synthesized for targeted delivery of the anticancer drug, paclitaxel, by grafting folic acid (FA) onto the PEGylated titanium dioxide nanoparticles. Titanium dioxide is used in biomedical field for its stability and no toxicity characteristics. Titanium dioxide is one of the most promising nanoparticles (NPs) capable of a wide variety of applications in medicine and life science. Polyethylene glycol (PEG), when attached to the surface of the nanoparticles, increases the biocompatibility of the nanoparticles. PEGylated nanocarriers evade the reticuloendothelial system (RES). Folic acid (FA) is used as the ligand to target folate receptors, which are found abundant in cancer cells. FA–PEG–TiO₂ nanoparticles when used as drug carriers have the ability to target cancer cells and also capable of evading the reticuloendothelial system. Titanium dioxide nanoparticles were synthesized by wet chemical method. It was annealed at 450° for 3 h. XRD analysis confirms the formation of anatase titanium dioxide. Analyses by transmission electron microscopy (TEM) and dynamic light scattering (DLS) revealed that the nanoparticles had an average size of 12 nm and uniform size distribution. The PEGylation and folic acid grafting was confirmed by UV spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA). The study on the loading of anticancer drug paclitaxel revealed that the titanium dioxide nanocarrier possessed a considerably higher adsorption capability. In addition, the in vitro release profile of paclitaxel from FA–PEG–TiO₂ nanoparticles was characterized by an initial fast release followed by a sustained release phase.     

Synthesis of Ti-containing MCM41 using Ti(SO4)2 as Ti source

A simple and economic method was developed to synthesize Ti-containing MCM41 from titanium sulphate as Ti source, sodium metasilicate as Si source and cetyltrimethylammonium bromide (CTABr) as template. The resultant materials were characterized by using XRD, FT–IR, N₂ adsorption isotherms, HRTEM, ICP, and LRS techniques. It was revealed that the atoms of titanium were incorporated into the framework of MCM41 for the samples with Ti / Si mol ratios below 1 / 20. Small amount of titanium oxides that highly dispersed onto the wall of MCM41 were detected while the Ti / Si mol ratios up to 1 / 10. The prepared materials exhibited high catalytic activity in the oxidation of aromatic compounds.     

The influence of preparation conditions on ZrO2 nanoparticles with different PEG–PPG–PEG surfactants by statistical experimental design

In this study mesoporous Zirconia powder with high surface area was prepared by using PEG–PPG–PEG new block copolymer as the non-ionic surfactant. The preparation conditions were optimized by Taguchi method of experimental design and Minitab Software to synthesize high surface area tetragonal-ZrO₂ nanoparticles. The BET surface area of powders was 114–175 m²/gr and the particles size calculated by Deby–Sherrer equation was 5–9 nm. pH = 11, aging time 38 h, Zr molarity 0.03, Surfactant/Zr mole ratio 0.04 and molecular weight 8400 were the best conditions to manufacture ZrO₂ with higher surface area. The sample prepared under optimized conditions was compared to that synthesized by PEG surfactant. XRD patterns of two ZrO₂ samples, hysteresis loop, pore size distribution, BET surface area and SEM results are similar.     

Oriented immobilization of immunoglobulin G onto the cuvette surface of the resonant mirror biosensor through layer-by-layer assembly of multilayer films

A new method for oriented immobilization of immunoglobulin G (IgG) onto the cuvette surface of the resonant mirror biosensor through layer-by-layer (LBL) assembly of multilayer films composed of avidin/gold nanoparticles (GNp)/protein A/IgG was developed. First, avidin was added in the biotin cuvette, and then injected GNp, followed by the injection of protein A for oriented immobilization of IgG. The rinsing with PBS was applied at the end of each assembly deposition for dissociating the weak adsorption. Second, IgG was added in the protein A-coated cuvette, and regenerated by incubation with 0.1 M glycine–HCL buffer. Third, different concentrations of IgG were measured by repeating the second process. Film assembling and properties of the interaction between protein A and IgG were studied by resonant mirror biosensor and electrochemical measurements. Results confirmed that IgG was successfully oriented on the protein A-coated cuvette surface by LBL assembly of multilayer films. The interaction response was dose-dependent which showed a linear range of 0.1 – 1.6 g L^− 1 IgG, with a detection limit of 8.7 mg L^− 1 estimated at a signal-to-noise ratio of 3. Moreover, the assay for oriented immobilization of IgG exhibited a good reproducibility and a favorable reusability. This method can provide a promising platform for fabricating immunoassay and immunosensor systems, protein reactors or protein-modified substrates, and affinity probes.     

A photoimmobilizable sulfobetaine-based polymer for a nonbiofouling surface

A novel photoreactive polymer containing sulfobetaine polar groups was prepared by copolymerization of two kinds of methacrylic acids with sulfobetaine and azidoaniline. The polymer was photoimmobilized on polyester and polystyrene surfaces. Its effects on surface modification were investigated from its interactions with water, proteins and cells. Polymer immobilization altered both of the plain surfaces to becoming hydrophilic in a similar range of static contact angles (12.5 ± 1.6° on polyester and 14.7 ± 2.2° on polystyrene). This suggests that the surfaces were covered with sulfobetaine polar groups. Micropattern immobilization was carried out on both polymers using a photomask. The formed pattern was identical to the photomask, showing that the polymer was formed in response to ultraviolet irradiation. Measurements using atomic force microscopy showed that the polymer was formed at a thickness of 550 nm, demonstrating that the polymer was cross-linked with itself and with the substrate molecules. Measurements using time-of-flight secondary ion mass spectrometry detected an abundance of sulfur-containing ions in the patterned polymer, confirming that sulfobetaine had been immobilized. Protein adsorption and mammalian cell adhesiveness were reduced markedly on the immobilized regions. The reduction of cell adhesiveness was concentration-dependent for the immobilized polymer on polyester surfaces. In conclusion, a novel sulfobetaine-containing polymer was immobilized photoreactively on conventional polymer surfaces and significantly reduced interactions with proteins and mammalian cells.     

Improved thrombogenicity on oxygen etched Ti6Al4V surfaces

Thrombus formation on blood contacting biomaterials continues to be a key factor in initiating a critical mode of failure in implantable devices, requiring immediate attention. In the interest of evaluating a solution for one of the most widely used biomaterials, titanium and its alloys, this study focuses on the use of a novel surface oxidation treatment to improve the blood compatibility. This study examines the possibility of using oblique angle ion etching to produce a high quality oxide layer that enhances blood compatibility on medical grade titanium alloy Ti6Al4V. An X-ray photoelectron spectroscopy (XPS) analysis of these oxygen-rich surfaces confirmed the presence of TiO₂ peaks and also indicated increased surface oxidation as well as a reduction in surface defects. After 2 h of contact with whole human plasma, the oxygen etched substrates demonstrated a reduction in both platelet adhesion and activation as compared to bare titanium substrates. The whole blood clotting behavior was evaluated for up to 45 min, showing a significant decrease in clot formation on oxygen etched substrates. Finally, a bicinchoninic acid (BCA) total protein assay and XPS were used to evaluate the degree of key blood serum protein (fibrinogen, albumin, immunoglobulin G) adsorption on the substrates. The results showed similar protein levels for both the oxygen etched and control substrates. These results indicate that oblique angle oxygen etching may be a promising method to increase the thrombogenicity of Ti6Al4V.     

Osteoblast interaction with laser cladded HA and SiO2-HA coatings on Ti–6Al–4V

In order to improve the bioactivity and biocompatibility of titanium endosseous implants, the morphology and composition of the surfaces were modified. Polished Ti–6Al–4V substrates were coated by a laser cladding process with different precursors: 100 wt.% HA and 25 wt.% SiO₂-HA. X-ray diffraction of the laser processed samples showed the presence of CaTiO₃, Ca₃(PO₄)₂, and Ca₂SiO₄ phases within the coatings. From in vitro studies, it was observed that compared to the unmodified substrate all laser cladded samples presented improved cellular interactions and bioactivity. The samples processed with 25 wt.% SiO₂-HA precursor showed a significantly higher HA precipitation after immersion in simulated body fluid than 100 wt.% HA precursor and titanium substrates. The in vitro biocompatibility of the laser cladded coatings and titanium substrate was investigated by culturing of mouse MC3T3-E1 pre-osteoblast cell line and analyzing the cell viability, cell proliferation, and cell morphology. A significantly higher cell attachment and proliferation rate were observed for both laser cladded 100 wt.% HA and 25 wt.% SiO₂-HA samples. Compared to 100 wt.% HA sample, 25 wt.% SiO₂-HA samples presented a slightly improved cellular interaction due to the addition of SiO₂. The staining of the actin filaments showed that the laser cladded samples induced a normal cytoskeleton and well-developed focal adhesion contacts. Scanning electron microscopic image of the cell cultured samples revealed better cell attachment and spreading for 25 wt.% SiO₂-HA and 100 wt.% HA coatings than titanium substrate. These results suggest that the laser cladding process improves the bioactivity and biocompatibility of titanium. The observed biological improvements are mainly due to the coating induced changes in surface chemistry and surface morphology.     

Characterisation of the bioactive behaviour of sol–gel hydroxyapatite–CaO and hydroxyapatite–CaO–bioactive glass composites

The fabrication and characterization of sol–gel derived hydroxyapatite–calcium oxide (HAp–CaO) material is investigated focusing on the effect of the addition of a bioactive glass on the material bioactive behaviour through the fabrication of a novel HAp–CaO (70 wt.%)–bioactive glass (30 wt.%) composite material. The bioactive behaviour of the materials was assessed by immersion studies in Simulated Body Fluid (SBF) and the alterations of the materials surfaces after soaking periods in SBF were characterized by Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). A brittle and weakly crystalline carbonate hydroxyapatite (HCAp) layer was found to develop on the surface of all samples, few hours after immersion in SBF, confirming the high bioactivity of the material. Alterations of the morphology of the developed HCAp layer, which led to a more compact structure, were observed on the surface of composite samples after 7 days of immersion in SBF. The presence of the CaO phase seems to accelerate the formation of HCAp, while the bioactive glass affects both the morphology and cohesion of the developed layer.     

Thermal oxidation of CP-Ti: Evaluation of characteristics and corrosion resistance as a function of treatment time

Commercially pure titanium (CP-Ti) samples were subjected to thermal oxidation (TO) treatment at 650 °C for 8, 16, 24 and 48 h. The morphological features, structural characteristics, microhardness and corrosion resistance in Ringer's solution of thermally oxidized samples were compared with that of the untreated one, to ascertain the suitability of thermally oxidized sample as a bio-implant. The thickness, morphological features and phase constituents of the oxide film formed during thermal oxidation (TO) exhibit a strong dependence on the treatment time. Samples oxidized for 48 h lead to the formation of oxide grains along with a thick oxide film consisting of rutile and TiO phase. Samples oxidized for 24 h lead to the formation of oxide grains with thinner oxide layer at the grain boundary. Almost a 3 fold increase in hardness is observed for samples oxidized for 48 h compared to that of the untreated sample. Based on the corrosion protective ability, the untreated and thermally oxidized samples can be ranked as follows: {TO 48 h} > {TO 16 h} > {TO 8 h} ≈ {TO 24 h} > untreated. From corrosion protection point of view, TO for 48 h is a promising surface treatment and it can be a suitable alternative to the untreated CP-Ti as a bio-implant.     

Antibacterial effects of silver-doped hydroxyapatite thin films sputter deposited on titanium

Since many orthopedic implants fail as a result of loosening, wear, and inflammation caused by repeated loading on the joints, coatings such as hydroxyapatite (HAp) on titanium with a unique topography have been shown to improve the interface between the implant and the natural tissue. Another serious problem with long-term or ideally permanent implants is infection. It is important to prevent initial bacterial colonization as existing colonies have the potential to become encased in an extracellular matrix polymer (biofilm) that is resistant to antibacterial agents. In this study, plasma-based ion implantation was used to examine the effects of pre-etching on plain titanium. Topographical changes to the titanium samples were examined and compared via scanning electron microscopy. Hydroxyapatite and silver-doped hydroxyapatite thin films were then sputter deposited on titanium substrates etched at ? 700 eV. For silver-doped films, two concentrations of silver (~ 0.5 wt.% and ~ 1.5 wt.%) were used. Silver concentrations in the film were determined using energy dispersive X-ray spectroscopy. Hydroxyapatite film thicknesses were determined by measuring the surface profile using contact profilometry. Staphylococcus epidermidis and Pseudomonas aeruginosa adhesion studies were performed on plain titanium, titanium coated with hydroxyapatite, titanium coated with ~ 0.5 wt.% silver-doped hydroxyapatite, and titanium coated with ~ 1.5 wt.% silver-doped hydroxyapatite. Results indicate that less bacteria adhered to surfaces containing hydroxyapatite and silver; further, as the hydroxyapatite films delaminated, silver ions were released which killed bacteria in suspension.