管式PECVD射频功率对氮化硅薄膜性能的影响

氮化硅薄膜作为传统的晶体硅太阳电池钝化减反膜,其性能的变化直接影响电池的转化效率。通过改变管式PECVD的射频功率,制备了不同膜厚和折射率的氮化硅薄膜,并分别进行了薄膜致密性以及硅片镀膜后少子寿命的测试。实验及测试结果表明,改变PECVD的射频功率对氮化硅薄膜的沉积速率及其薄膜的性能有重要影响。     

PECVD制备SiOx-SiNx薄膜的研究

首先使用工业型Direct-PECVD设备,采用SiH4和N2O制备了SiOx薄膜.针对Si太阳电池的应用,比较了SiOx薄膜在不同射频功率、气压、气体流量比和温度下的沉积特性,得出了最佳的沉积条件,这些沉积特性包括沉积速率、折射率和腐蚀速率.在该条件下沉积的SiOx膜均匀性良好、结构致密、沉积速率稳定,其性能满足了现阶段Si太阳电池对减反钝化层的光学和电学性能方面的要求.然后制备了SiOx-SiNx叠层减反钝化膜,并比较了SiO2与SiNx单层膜的减反和钝化效果,结果显示SiOx-SiNx叠层膜在不增加反射率的同时显著提高了Si片的钝化效果.     

快速热处理对PECVD氮化硅薄膜性能的影响

利用PECVD在硅片上沉积了氮化硅(SiNx)薄膜,将沉积膜后的样品放在N2气氛中进行快速热处理(RTP),研究了不同快速热处理对PECVD氮化硅薄膜件能的影响.采用原子力显微镜(AFM)检测薄膜的表面形貌,利用椭圆偏振仪测量样品膜厚和折射率,利用准稳态光电导衰减法(QSSPCD)测鼋样品的少子寿命.实验结果表明随着RTP温度的升高,薄膜厚度迅速减小,折射率迅速增大;低于500℃热处理时,少子寿命基本不变;高于500℃热处理时,随着温度的升高,少子寿命急剧下降.氮化硅薄膜经热处理后反射率基本不变.     

PECVD制备氮化硅薄膜的研究

采用PECVD法制备了氮化硅薄膜,探讨了沉积参数对氮化硅薄膜折射率的影响和衬底温度对氮化硅薄膜形貌和成分的影响规律。结果表明,不同的NH3流量可改变反应腔体内的氮硅比,对氮化硅的折射率,即减反射性能影响较大;衬底温度是影响氮化硅薄膜形貌和成分的主要因素;在衬底温度达到400℃时,形成了白色团状或岛状的氮化硅膜。     

PECVD沉积双层SiNx对太阳电池性能的影响

提出了一种简单有效的制备双层SiNx薄膜的方法,其薄膜具有良好的减反射钝化特性。采用等离子体增强化学气相沉积(PECVD)的方法,通过控制SiH4和NH3气体流量比,在p型多晶硅衬底上生长单层及双层SiNx膜。随后使用薄膜测试分析仪测量了薄膜的厚度、折射率及反射率,并用Semilab WT-2000测量少数载流子寿命,通过测量量子效率,对单、双层膜电池进行了比较。实验结果表明:相比单层减反射钝化膜,采用双层SiNx膜,少数载流子寿命可以得到更好的改善,开路电压可提高约2 mV,短路电流可提高约40 mA,电池效率能提高0.15%。     

晶体硅太阳电池减反射膜的研究

在太阳电池表面形成一层减反射薄膜是提高太阳电池的光电转换效率比较可行且降低成本的方法。应用PECVD（等离子体增强化学气相沉积）系统,采用SiH4和NH3气源以制备氮化硅薄膜。研究探索了PECVD生长氮化硅薄膜的基本物化性质以及在沉积过程中反应压强、反应温度、硅烷氨气流量比和微波功率对薄膜性质的影响。通过大量实验,分析了氮化硅薄膜的相对最佳沉积参数,并得出制作减反射膜的优化工艺。     

界面层对激光减反膜的影响研究

激光技术的发展对减反膜提出了超高透过率的要求,基板的表面特征在高精度减反膜的设计与制造中不可忽略.选择熔融石英为基板,Ta2O5和SiO2为高低折射率膜层材料,针对在0 °入射角下工作的532 nm激光减反膜进行设计与分析,得到膜层内的电场分布.在模拟计算中将基板的表面粗糙度等效为等比例混合膜,计算分析了理想设计条件下...     

双波段激光防护红外减反膜的研制

针对军用光电仪器对激光致盲武器的防护要求,选取Si和YbF3,ZnS和YbF3两种高低折射率组合形式研制了激光防护减反膜。在多光谱ZnS基底上,采用电子束及离子辅助沉积技术,制备了能够对532 nm和1064 nm激光进行有效防护,同时对3~5μm的波段具有高透射率的薄膜。对Si膜的电子束沉积工艺进行了研究;对YbF3在不同的材料组合中的沉积工艺进行了优化;解决了膜层与基底之间的粘附性问题。该薄膜集探测用减反器件和防护器件于一体,可以使星载、机载等光电仪器的结构得到简化;光谱分析和环境测试的结果表明,各项指标满足使用要求。     

PECVD SiON膜的性质及其在双层互连工艺中的应用

我们在研制和生产双层布线的 3μm CMOS LSI器件时,采用了 PECVD SiON(等离子增强化学气相沉积的氮氧化硅)膜作金属层之间的绝缘层.这种薄膜具有很小的压应力,很低的针孔密度,良好的台阶覆盖性等优点.这种绝缘膜是采用PECVD沉积工艺,以氮冲稀的低浓度SiH_4(3％)和N_2O气体为原料制得的. 本文着重介绍 PECVD SiON膜的性质及其在双层互连工艺中的应用.     

用椭偏法研究掺磷a-Si:H薄膜的光学特性

用等离子体增强化学气相沉积(PECVD)方法制备了磷掺杂氢化非晶硅(a-Si∶H)薄膜.分别以50°和70°为入射角,测试了样品在300～1000nm波长的椭偏光谱,得到了其膜厚和光学常数谱(折射率和消光系数随波长变化谱),并应用Tauc作图法推算出了薄膜的光学带隙.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.