Improved hydrogen desorption in lithium alanate by addition of SWCNT-metallic catalyst composite

A LiAlH₄/single walled carbon nanotube (SWCNT) composite system was prepared by mechanical milling and its hydrogen storage properties investigated. The SWCNT - metallic particle addition resulted in both a decreased decomposition temperature and enhanced desorption kinetics compared to pure LiAlH₄. The decomposition temperature of the 5 wt.% SWCNT-added LiAlH₄ sample was reduced to 80 °C and 130 °C for the first and second stage, respectively, compared with 150 °C and 180 °C for as-received LiAlH₄. In terms of the desorption kinetics, the 5 wt.% SWCNT-added LiAlH₄ sample released about 4.0 wt.% hydrogen at 90 °C after 40 min dehydrogenation, while the as-milled LiAlH₄ sample released less than 0.3 wt.% hydrogen for the same temperature and time. Differential scanning calorimetry measurements indicate that enthalpies of decomposition in LiAlH₄ decrease with added SWCNTs. The apparent activation energy for hydrogen desorption was decreased from 116 kJ/mol for as-received LiAlH₄ to 61 kJ/mol by the addition of 5 wt.% SWCNTs. It is believed that the significant improvement in dehydrogenation behaviour of SWCNT-added LiAlH₄ is due to the combined influence of the SWCNT structure itself and the catalytic role of the metallic particles contained in the SWCNTs. In addition, the different effects of the SWCNTs and the metallic catalysts contained in the SWCNTs were also investigated, and the possible mechanism is discussed.     

Enhancement of the H2 desorption properties of LiAlH4 doping with NiCo2O4 nanorods

Lithium aluminum hydride (LiAlH₄) is considered as an attractive candidate for hydrogen storage owing to its favorable thermodynamics and high hydrogen storage capacity. However, its reaction kinetics and thermodynamics have to be improved for the practical application. In our present work, we have systematically investigated the effect of NiCo₂O₄ (NCO) additive on the dehydrogenation properties and microstructure refinement in LiAlH₄. The dehydrogenation kinetics of LiAlH₄ can be significantly increased with the increase of NiCo₂O₄ content and dehydrogenation temperature. The 2 mol% NiCo₂O₄-doped LiAlH₄ (2% NCO–LiAlH₄) exhibits the superior dehydrogenation performances, which releases 4.95 wt% H₂ at 130 °C and 6.47 wt% H₂ at 150 °C within 150 min. In contrast, the undoped LiAlH₄ sample just releases <1 wt% H₂ after 150 min. About 3.7 wt.% of hydrogen can be released from 2% NCO–LiAlH₄ at 90 °C, where total 7.10 wt% of hydrogen is released at 150 °C. Moreover, 2% NCO–LiAlH₄ displayed remarkably reduced activation energy for the dehydrogenation of LiAlH₄.     

Effects of REF3 (RE = Y,La, Ce) additives on dehydrogenation properties of LiAlH4

The catalytic effects of rare earth fluoride REF₃ (RE = Y, La, Ce) additives on the dehydrogenation properties of LiAlH₄ were carefully investigated in the present work. The results showed that the dehydrogenation behaviors of LiAlH₄ were significantly altered by the addition of 5 mol% REF₃ through ball milling. The destabilization ability of these catalysts on LiAlH₄ has the order: CeF₃>LaF₃>YF₃. For instance, the temperature programmed desorption (TPD) analyses showed that the onset dehydrogenation temperature of CeF₃ doped LiAlH₄ was sharply reduced by 90 °C compared to that of pristine LiAlH₄. Based on differential scanning calorimetry (DSC) analyses, the dehydriding activation energies of the CeF₃ doped LiAlH₄ sample were 40.9 kJ/mol H₂ and 77.2 kJ/mol H₂ for the first and second dehydrogenation stages, respectively, which decreased about 40.0 kJ/mol H₂ and 60.3 kJ/mol H₂ compared with those of pure LiAlH₄. In addition, the sample doped with CeF₃ showed the fastest dehydrogenation rate among the REF₃ doped LiAlH₄ samples at both 125 °C and 150 °C during the isothermal desorption. The phase changes in REF₃ doped LiAlH₄ samples during ball milling and dehydrogenation were examined using X-ray diffraction and the mechanisms related to the catalytic effects of REF₃ were proposed.     

Effects of NbF5 addition on the hydrogen storage properties of LiAlH4

We investigated the effects of NbF₅ addition by ball milling on the hydrogen storage properties of LiAlH₄. Pressure-composition-temperature (PCT) experiments showed that addition of 0.5 and 1 mol% NbF₅ in LiAlH₄ improves the onset desorption temperature and results in little decrease in hydrogen capacity, with approximately 7.0 wt% released by 188 °C. Isothermal dehydriding kinetics measurements indicated that the NbF₅-doped sample shows an average dehydrogenation rate 5–6 times faster than that of the as-received LiAlH₄ sample. In the x-ray diffraction results, there are distinct peaks of Al and LiH that appear after desorption. There is no peak of NbF₅ before or after desorption. Desorption kinetics measurements indicated that the activation energy, E_A, for LiAlH₄ + 1 mol% NbF₅ is about 67 kJ/mol for first reaction stage and about 77 kJ/mol for second reaction stage. The desorption process was further characterised by differential scanning calorimetry, and the possible mechanism of the effects of NbF₅ addition is discussed.     

The effects of the micrometric and nanometric iron (Fe) additives on the mechanical and thermal dehydrogenation of lithium alanate (LiAlH4), its self-discharge at low temperatures and rehydrogenation

LiAlH₄ containing 5 wt.% of nanometric Fe (n-Fe) shows a profound mechanical dehydrogenation by continuously desorbing hydrogen (H₂) during high energy ball milling reaching ∼3.5 wt.% H₂ after 5 h of milling. In contrast, no H₂ desorption is observed during low energy milling of LiAlH₄ containing n-Fe. Similarly, no H₂ desorption occurs during high energy ball milling for LiAlH₄ containing micrometric Fe (μ-Fe) and, for comparison, both the micrometric and nanometric Ni (μ-Ni and n-Ni) additive. X-ray diffraction studies show that ball milling results in a varying degree of the lattice expansion of LiAlH₄ for both the Fe and Ni additives. A volumetric lattice expansion larger than 1% results in the profound destabilization of LiAlH₄ accompanied by continuous H₂ desorption during milling according to reaction: LiAlH₄ (solid) → 1/3Li₃AlH₆ + 2/3Al + H₂. It is hypothesized that the Fe ions are able to dissolve in the lattice of LiAlH₄ by the action of mechanical energy, replacing the Al ions and forming a substitutional solid solution. The quantity of dissolved metal ions depends primarily on the total energy of milling per unit mass of powder generated within a prescribed milling time, the type of additive ion e.g. Fe vs. Ni and on the particle size (micrometric vs. nanometric) of metal additive. For thermal dehydrogenation the average apparent activation energy of Stage I (LiAlH₄ (solid) → 1/3Li₃AlH₆ + 2/3Al + H₂) is reduced from the range 76 to 96 kJ/mol for the μ-Fe additive to about 60 kJ/mol for the n-Fe additive. For Stage II dehydrogenation (1/3Li₃AlH₆ → LiH+1/3Al + 0.5H₂) the average apparent activation energy is within the range 77–93 kJ/mol, regardless of the particle size of the Fe additive (μ-Fe vs. n-Fe). The n-Fe and n-Ni additives, the latter used for comparison, provide nearly identical enhancement of dehydrogenation rate during isothermal dehydrogenation at 100 °C. Ball milled (LiAlH₄ + 5 wt.% n-Fe) slowly self-discharges up to ∼5 wt.% H₂ during storage at room temperature (RT), 40 and 80 °C. Fully dehydrogenated (LiAlH₄ + 5 wt.% n-Fe) has been partially rehydrogenated up to 0.5 wt.% H₂ under 100 bar/160°C/24 h. However, the rehydrogenation parameters are not optimized yet.     

Significantly improved dehydrogenation of LiAlH4 destabilized by K2TiF6

The effects of K₂TiF₆ on the dehydrogenation properties of LiAlH₄ were investigated by solid-state ball milling. The onset decomposition temperature of 0.8 mol% K₂TiF₆ doped LiAlH₄ is as low as 65 °C that 85 °C lower than that of pristine LiAlH₄. Isothermal dehydrogenation properties of the doped LiAlH₄ were studied by PCT (pressure–composition–temperature). The results show that, for the 0.8 mol% K₂TiF₆ doped LiAlH₄ that dehydrogenated at 90 °C, 4.4 wt% and 6.0 wt% of hydrogen can be released in 60 min and 300 min, respectively. When temperature was increased to 120 °C, the doped LiAlH₄ can finish its first two dehydrogenation steps in 170 min. DSC results show that the apparent activation energy (E_a) for the first two dehydrogenation steps of LiAlH₄ are both reduced, and XRD results suggest that TiH₂, Al₃Ti, LiF and KH are in situ formed, which are responsible for the improved dehydrogenation properties of LiAlH₄.     

Enhanced hydrogen storage properties of 4MgH2 + LiAlH4 composite system by doping with Fe2O3 nanopowder

In this paper, the hydrogen storage properties and reaction mechanism of the 4MgH₂ + LiAlH₄ composite system with the addition of Fe₂O₃ nanopowder were investigated. Temperature-programmed-desorption results show that the addition of 5 wt.% Fe₂O₃ to the 4MgH₂ + LiAlH₄ composite system improves the onset desorption temperature to 95 °C and 270 °C for the first two dehydrogenation stage, which is lower 40 °C and 10 °C than the undoped composite. The dehydrogenation and rehydrogenation kinetics of 5 wt.% Fe₂O₃-doped 4MgH₂ + LiAlH₄ composite were also improved significantly as compared to the undoped composite. Differential scanning calorimetry measurements indicate that the enthalpy change in the 4MgH₂–LiAlH₄ composite system was unaffected by the addition of Fe₂O₃ nanopowder. The Kissinger analysis demonstrated that the apparent activation energy of the 4MgH₂ + LiAlH₄ composite (125.6 kJ/mol) was reduced to 117.1 kJ/mol after doping with 5 wt.% Fe₂O₃. Meanwhile, the X-ray diffraction analysis shows the formation of a new phase of Li₂Fe₃O₄ in the doped composite after the dehydrogenation and rehydrogenation process. It is believed that Li₂Fe₃O₄ acts as an actual catalyst in the 4MgH₂ + LiAlH₄ + 5 wt.% Fe₂O₃ composite which may promote the interaction of MgH₂ and LiAlH₄ and thus accelerate the hydrogen sorption performance of the MgH₂ + LiAlH₄ composite system.     

Hydrogen desorption properties of MgH2/LiAlH4 composites

The hydrogen desorption properties of MgH₂–LiAlH₄ composites obtained by mechanical milling for different milling times have been investigated by Thermal Desorption Spectroscopy (TDS) and correlated to the sample microstructure and morphology analysed by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The MgH₂–LiAlH₄ composites show improved hydrogen desorption properties in comparison with both as-received and ball-milled MgH₂. Mixing of MgH₂ with small amount of LiAlH₄ (5 wt.%) using short mechanical milling (15 min) shifts, in fact, the hydrogen desorption peak to lower temperature than those observed with both as-received and milled MgH₂ samples. Longer mixing times of the MgH₂–LiAlH₄ composites (30 and 60 min) reduce the catalytic activity of the LiAlH₄ additive as revealed by the shift of the hydrogen desorption peak to higher temperatures.     

Enhanced hydrogen storage performance of LiAlH4-MgH2-TiF3 composite

The mutual destabilization of LiAlH₄ and MgH₂ in the reactive hydride composite LiAlH₄-MgH₂ is attributed to the formation of intermediate compounds, including Li-Mg and Mg-Al alloys, upon dehydrogenation. TiF₃ was doped into the composite for promoting this interaction and thus enhancing the hydrogen sorption properties. Experimental analysis on the LiAlH₄-MgH₂-TiF₃ composite was performed via temperature-programmed desorption (TPD), differential scanning calorimetry (DSC), isothermal sorption, pressure-composition isotherms (PCI), and powder X-ray diffraction (XRD). For LiAlH₄-MgH₂-TiF₃ composite (mole ratio 1:1:0.05), the dehydrogenation temperature range starts from about 60 °C, which is 100 °C lower than for LiAlH₄-MgH₂. At 300 °C, the LiAlH₄-MgH₂-TiF₃ composite can desorb 2.48 wt% hydrogen in 10 min during its second stage dehydrogenation, corresponding to the decomposition of MgH₂. In contrast, 20 min was required for the LiAlH₄-MgH₂ sample to release so much hydrogen capacity under the same conditions. The hydrogen absorption properties of the LiAlH₄-MgH₂-TiF₃ composite were also improved significantly as compared to the LiAlH₄-MgH₂ composite. A hydrogen absorption capacity of 2.68 wt% under 300 °C and 20 atm H₂ pressure was reached after 5 min in the LiAlH₄-MgH₂-TiF₃ composite, which is larger than that of LiAlH₄-MgH₂ (1.75 wt%). XRD results show that the MgH₂ and LiH were reformed after rehydrogenation.     

Effect of ball milling time on the hydrogen storage properties of TiF3-doped LiAlH4

In the present work, the catalytic effect of TiF₃ on the dehydrogenation properties of LiAlH₄ has been investigated. Decomposition of LiAlH₄ occurs during ball milling in the presence of 4 mol% TiF₃. Different ball milling times have been used, from 0.5 h to 18 h. With ball milling time increasing, the crystallite sizes of LiAlH₄ get smaller (from 69 nm to 43 nm) and the dehydrogenation temperature becomes lower (from 80 °C to 60 °C). Half an hour ball milling makes the initial dehydrogenation temperature of doped LiAlH₄ reduce to 80 °C, which is 70 °C lower than as-received LiAlH₄. About 5.0 wt.% H₂ can be released from TiF₃-doped LiAlH₄ after 18 h ball milling in the range of 60 °C–145 °C (heating rate 2 °C min⁻¹). TiF₃ probably reacts with LiAlH₄ to form the catalyst, TiAl₃. The mechanochemical and thermochemical reactions have been clarified. However, the rehydrogenation of LiAlH₄/Li₃AlH₆ can not be realized under 95 bar H₂ in the presence of TiF₃ because of their thermodynamic properties.     

Enhanced hydrogen storage properties of LiBH4 modified by NbF5

In this work, the hydriding–dehydriding properties of the LiBH₄–NbF₅ mixtures were investigated. It was found that the dehydrogenation and reversibility properties of LiBH₄ were significantly improved by NbF₅. Temperature-programed dehydrogenation (TPD) showed that 5LiBH₄–NbF₅ sample started releasing hydrogen from as low as 60 °C, and 4 wt.% hydrogen could be obtained below 255 °C. Meanwhile, ∼7 wt.% H₂ could be reached at 400 °C in 20LiBH₄–NbF₅ sample, whereas pristine LiBH₄ only released ∼0.7 wt.% H₂. In addition, reversibility measurement demonstrated that over 4.4 wt.% H₂ could still be released even during the fifth dehydrogenation in 20LiBH₄–NbF₅ sample. The experimental results suggested that a new borohydride possibly formed during ball milling the LiBH₄–NbF₅ mixtures might be the source of the active effect of NbF₅ on LiBH₄.     

Enhanced desorption properties of LiBH4 incorporated into mesoporous TiO2

LiBH₄ nano-particles are incorporated into mesoporous TiO₂ scaffolds via a chemical impregnation method. And the enhanced desorption properties of the composite have been investigated. The LiBH₄/TiO₂ sample starts to release hydrogen at 220 °C and the maximal desorption peak occurs at about 330 °C, much lower compared to the bulk LiBH₄. Furthermore, the composite exhibits excellent dehydrogenation kinetics, with 11 wt% of hydrogen liberated from LiBH₄ at 300 °C within 3 h. X-ray diffraction and Fourier transform infrared spectroscopy are used to confirm the nanostructure of LiBH₄ in the TiO₂ scaffold. This work demonstrates that confinement within active porous scaffold host is a promising approach for enhancing hydrogen decomposition properties of light-metal complex hydrides.     

Enhanced hydrogen storage properties of TiN–LiAlH4 composite

The hydrogen storage properties of LiAlH₄ doped efficient TiN catalyst were systematically investigated. We observe that TiN catalyst enhances the dehydrogenation kinetics and decreases the dehydrogenation temperature of LiAlH₄. The dehydrogenation behaviors of 2%TiN–LiAlH₄ are investigated using temperature programmed desorption (TPD), differential scanning calorimetry (DSC) and fourier transform infrared spectroscopy (FTIR). Interestingly, the onset hydrogen desorption temperature of 2%TiN–LiAlH₄ sample gets lowered from 151.0 °C to 90.0 °C with a faster kinetics, and the dehydrogenation rate reached a maximum value at 137.2 °C. By adding a small amount of as-prepared TiN, approximately 7.1 wt% of hydrogen can be released from the LiAlH₄ at 130 °C. Interestingly, the result of the FTIR indicates that the 2%TiN–LiAlH₄ maybe restore hydrogen under 5.5 MPa hydrogen. Moreover, 2%TiN–LiAlH₄ displayed a substantially reduced activation energy for LiAlH₄ dehydrogenation.     

Improved reversible hydrogen storage of LiAlH4 by nano-sized TiH2

Transition metal halides are mostly used as dopants to improve the hydrogen storage properties of LiAlH₄, but they will cause hydrogen capacity loss because of their relatively high molecular weights and reactions with LiAlH₄. To overcome these drawbacks, active nano-sized TiH₂ (TiH₂^nano) prepared by reactive ball milling is used to dope LiAlH₄. It shows superior catalytic effect on the dehydrogenation of LiAlH₄ compared to commercial TiH₂. TiH₂^nano-doped LiAlH₄ starts to release hydrogen at 75 °C, which is 80 °C lower than the onset dehydrogenation temperature of commercial LiAlH₄. About 6.3 wt.% H₂ can be released isothermally at 100 °C (800 min) or at 120 °C (150 min). The apparent activation energies of the first two dehydrogenation reactions of LiAlH₄ are reduced by about 20 and 24 kJ mol⁻¹, respectively. Meanwhile, the regeneration of LiAlH₄ is realized through extracting the solvent from LiAlH₄·4THF, which is obtained by ball milling the dehydrogenated products of TiH₂^nano-doped LiAlH₄ in the presence of THF and 5 MPa H₂. This suggests that TiH₂ is also an effective catalyst for the formation of LiAlH₄·4THF.     

Hydrogen generation from the ball milled composites of sodium and lithium borohydride (NaBH4/LiBH4) and magnesium hydroxide (Mg(OH)2) without and with the nanometric nickel (Ni) additive

The composites of (NaBH₄+2Mg(OH)₂) and (LiBH₄+2Mg(OH)₂) without and with nanometric Ni (n-Ni) added as a potential catalyst were synthesized by high energy ball milling. The ball milled NaBH₄-based composite desorbs hydrogen in one exothermic reaction in contrast to its LiBH₄-based counterpart which dehydrogenates in two reactions: an exothermic and endothermic. The NaBH₄-based composite starts desorbing hydrogen at 240 °C. Its ball milled LiBH₄-based counterpart starts desorbing at 200 °C. The latter initially desorbs hydrogen rapidly but then the rate of desorption suddenly decelerates. The estimated apparent activation energy for the NaBH₄-based composite without and with n-Ni is equal to 152 ± 2.2 and 157 ± 0.9 kJ/mol, respectively. In contrast, the apparent activation energy for the initial rapid dehydrogenation for the LiBH₄-based composite is very low being equal to 47 ± 2 and 38 ± 9 kJ/mol for the composite without and with the n-Ni additive, respectively. XRD phase studies after volumetric isothermal dehydrogenation tests show the presence of NaBO₂ and MgO for the NaBH₄-based composite. For the LiBH₄-based composite phases such as MgO, Li₃BO₃, MgB₂, MgB₆ are the products of the first exothermic reaction which has a theoretical H₂ capacity of 8.1 wt.%. However, for reasons which are not quite clear, the first reaction never goes to full completion even at 300 °C desorbing ∼4.5 wt.% H₂ at this temperature. The products of the second endothermic reaction for the LiBH₄-based composite are MgO, MgB₆, B and LiMgBO₃ and the reaction has a theoretical H₂ capacity of 2.26 wt.%. The effect of the addition of 5 wt.% nanometric Ni on the dehydrogenation behavior of both the NaBH₄-and LiBH₄-based composites is rather negligible. The n-Ni additive may not be the optimal catalyst for these hydride composite systems although more tests are required since only one n-Ni content was examined.     

The effects of the nanometric interstitial compounds TiC,ZrC and TiN on the mechanical and thermal dehydrogenation and rehydrogenation of the nanocomposite lithium alanate (LiAlH4) hydride

Profuse mechanical dehydrogenation occurs during controlled high energy ball milling of LiAlH₄ containing 5 wt.% of the nanometric interstitial compounds such as n-TiC, n-TiN and n-ZrC which involves a gradual decomposition of LiAlH₄ to the mixture of Li₃AlH₆ and Al (Stage I) followed by a further decomposition of Li₃AlH₆ to the mixture of Al and LiH (Stage II). XRD reveals that the interstitial compounds remain stable in the hydride matrix during entire ball milling duration. The effectiveness of the nanometric interstitial compound additives for mechanical dehydrogenation increases on the order of n-TiN > n-TiC > n-ZrC. X-ray diffraction (XRD) reveals that there is no measurable change in a unit cell volume of LiAlH₄ after ball milling which indicates that an accelerated mechanical dehydrogenation of LiAlH₄ containing the nanometric interstitial compounds is unrelated to the lattice expansion as we have already reported for the nanometric metal Fe (n-Fe). In addition, the observed strong catalytic activity of the nanometric interstitial compounds for mechanical dehydrogenation is not related to their valence electron concentration (VEC) number. However, the n-TiN additive, which is the most effective one for mechanical dehydrogenation, has the smallest average particle size of 20 nm and the largest Specific Surface Area (SSA > 80 m²/g). For thermal dehydrogenation in Stage I the average apparent activation energy, E_A, for the interstitial compound additives is within the range of 87–96 kJ/mol whereas, for comparison, the nanometric metallic additives, n-Fe and n-Ni, exhibit drastically smaller apparent activation energy on the order of 55–70 kJ/mol. The average apparent activation energy for thermal dehydrogenation in Stage II is in the range of 63–80 kJ/mol in the order of E_A(n-ZrC) < E_A(n-Ti = n-TiC) and is lower than that for the nanometric metal additives n-Ni and n-Fe. In summary, the nanometric interstitial compounds do not substantially affect the apparent activation energy of Stage I but are able to reduce the apparent activation energy of thermal dehydrogenation in Stage II. XRD reveals that the interstitial compounds remain stable in the hydride matrix up to the dehydrogenation temperature of at least 165 °C. Ball milled LiAlH₄ containing 5 wt.% n-TiC, n-TiN and n-ZrC is able to slowly discharge large quantities of H₂ up to 5–6 wt.% during storage at 40 °C. Unfortunately, the results of rehydrogenation at 165 °C under 95 bar for 5 h indicate that LiAlH₄ containing the nanometric interstitial compounds exhibits no rehydrogenation.     

Influence of metal oxide on LiBH4/2LiNH2/MgH2 system for hydrogen storage properties

In this study, various nanoscale metal oxide catalysts, such as CeO₂, TiO₂, Fe₂O₃, Co₃O₄, and SiO₂, were added to the LiBH₄/2LiNH₂/MgH₂ system by using high-energy ball milling. Temperature programmed desorption and MS results showed that the Li–Mg–B–N–H/oxide mixtures were able to dehydrogenate at much lower temperatures. The order of the catalytic effect of the studied oxides was Fe₂O₃ > Co₃O₄ > CeO₂ > TiO₂ > SiO₂. The onset dehydrogenation temperature was below 70 °C for the samples doped with Fe₂O₃ and Co₃O₄ with 10 wt.%. More than 5.4 wt.% hydrogen was released at 140 °C. X-ray diffraction indicated that the addition of metal oxides inhibited the formation of Mg(NH₂)₂ during ball milling processes. It is thought that the changing of the ball milling products results from the interaction of oxide ions in metal oxide catalysts with hydrogen atoms in MgH₂. The catalytic effect depends on the activation capability of oxygen species in metal oxides on hydrogen atoms in hydrides.     

Improved hydrogen sorption performance of NbF5-catalysed NaAlH4

The effect of NbF₅ on the hydrogen sorption performance of NaAlH₄ has been investigated. It was found that the dehydrogenation/hydrogenation properties of NaAlH₄ were significantly enhanced by mechanically milling with 3 mol% NbF₅. Differential scanning calorimetry results indicate that the ball-milled NaAlH₄-0.03NbF₅ sample lowered the completion temperature for the first two steps dehydrogenation by 71 °C compared to the pristine NaAlH₄ sample. Isothermal hydrogen sorption measurements also revealed a significant enhancement in terms of the sorption rate and capacity, in particular, at reduced operation temperatures. The apparent activation energy for the first-step and the second-step dehydrogenation of the NaAlH₄-0.03NbF₅ sample is estimated to be 88.2 kJ/mol and 102.9 kJ/mol, respectively, by using Kissinger’s approach, which is much lower than for pristine NaAlH₄, indicating the reduced kinetic barrier. The rehydrogenation kinetics of NaAlH₄ was also improved with 3 mol% NbF₅ doping, absorbing ∼1.7 wt% hydrogen at 150 °C for 2 h under ∼5.5 MPa hydrogen pressure. In contrast, no hydrogen was absorbed by the pristine NaAlH₄ sample under the same conditions. The formation of Na₃AlH₆ was detected by X-ray diffraction on the rehydrogenated NaAlH₄-0.03NbF₅ sample. Furthermore, the structural changes in the NbF₅-doped NaAlH₄ sample after ball milling and the hydrogen sorption were carefully examined, and the active species and mechanism of catalysis in NbF₅-doped NaAlH₄ are discussed.     

Synthesis and dehydrogenation of LiCa(NH2)3(BH3)2

We report the synthesis of a new hydrogen storage material with a composition of LiCa(NH₂)₃(BH₃)₂. The theoretical hydrogen capacity of LiCa(NH₂)₃(BH₃)₂ is 9.85 wt.%. It can be prepared by ball milling the mixture of calcium amidoborane (Ca(NH₂BH₃)₂) and lithium amide (LiNH₂) in a molar ratio of 1:1. The experimental results show that this material starts to release hydrogen at a temperature as low as ca. 50 °C, which is ca. 70 °C lower than that of pure Ca(NH₂BH₃)₂ possibly resulting from the active interaction of NH₂⁻ in LiNH₂ with BH₃ in Ca(NH₂BH₃)₂. ca. 4.1 equiv. or 6.8 wt.% hydrogen can be released at 300 °C. The dehydrogenation is a mildly exothermic process forming stable nitride products.     

A synergistic effect between nanoconfinement of carbon aerogels and catalysis of CoNiB nanoparticles on dehydrogenation of LiBH4

A synergistic effect of nanoconfinement and catalyzing is a new strategy to enhance the dehydrogenation properties of complex hydrides. Herein, LiBH₄ has been infiltrated into a CoNiB-loaded carbon aerogels system (donated as LiBH₄@CA@CoNiB). It is found that the desorption performances of LiBH₄ are significantly strengthened. The onset desorption temperature of LiBH₄@CA@CoNiB is decreased to 192 °C, and majority of the liberation occurs at about 320 °C, much lower than that of pure LiBH₄. Also, about 15.9 wt% H₂ could be released below 600 °C. Furthermore, LiBH₄ doped with CA@CoNiB exhibits an excellent desorption kinetics, with a capacity of 9.33 wt% H₂ released in 30 min at 350 °C, while only 2.13 wt% H₂ is gained for bulk LiBH₄. In addition, the apparent activation energy (Ea) is reduced sharply from 59.00 kJ/mol (pure LiBH₄) to 46.39 kJ/mol.