Compact implementation of high-performance CMOS current mirror

A high-performance compact current mirror implementation with very low input resistance, very high output resistance, high copying accuracy, low input and output voltage supply requirements and high bandwidth is proposed. The circuit characteristics are validated with simulations in 0.5 /spl mu/m CMOS technology and with experimental results.     

Low-voltage high performance compact all cascode CMOS current mirror

A high performance and compact current mirror with extremely low input and high output resistances (R/sub in//spl sim/0.01/spl Omega/, R/sub out//spl sim/10 G/spl Omega/), high copying accuracy, very low input and output voltage requirements (V/sub in/, V/sub out//spl ges/V/sub DSsat/), high bandwidth (200 MHz using a 0.5 /spl mu/m CMOS technology) and low settling time (25 ns) is proposed. Simulations and experimental results are shown that validate the circuit.     

A high current drive CMOS output stage with a tunable quiescent current limiting circuit

A CMOS output stage based on a complementary common source with an original quiescent current limiting circuit is presented. The quiescent current can be varied over a wide range by means of a control current with no need to modify the transistor aspect ratios. The output stage has been coupled to a conventional complementary input stage to form a rail-to-rail buffer. A prototype with the inclusion of auxiliary pins for biasing and current monitoring purposes has been designed using the 1-/spl mu/m double-polysilicon BCD3S process of STMicroelectronics. On a single 5-V power supply, the maximum output current is 20 mA. The amplifier, biased for a total power dissipation of 1 mW, exhibits a total harmonic distortion of -58 dB at 1 kHz with 4-V peak-to-peak on a 330-/spl Omega/ load. Correct operation of the quiescent current limiting circuit has been demonstrated for a minimum supply voltage of 2.2 V.     

A high-voltage output driver in a 2.5-V 0.25-/spl mu/m CMOS technology

The design of a high-voltage output driver in a digital 0.25-/spl mu/m 2.5-V technology is presented. The use of stacked devices with a self-biased cascode topology allows the driver to operate at three times the nominal supply voltage. Oxide stress and hot carrier degradation is minimized since the driver operates within the voltage limits imposed by the design rules of a mainstream CMOS technology. The proposed high-voltage architecture uses a switching output stage. The realized prototype delivers an output swing of 6.46 V to a 50-/spl Omega/ load with a 7.5-V supply and an input square wave of 10 MHz. A PWM signal with a dual-tone sinusoid at 70 kHz and 250 kHz results in an IM3 of -65 dB and an IM2 of -67 dB. The on-resistance is 5.9 /spl Omega/.     

A quad CMOS single-supply op amp with rail-to-rail output swing

The realization of a commercially viable, general-purpose quad CMOS amplifier is presented, along with discussions of the tradeoffs involved in such a design. The amplifier features an output swing that extends to either supply rail, together with an input common-mode range that includes ground. The device is especially well suited for single-supply operation and is fully specified for operation from 5 to 15 V over a temperature range of -55 to +125/spl deg/C. In the areas of input offset voltage, offset voltage drift, input noise voltage, voltage gain, and load driving capability, this implementation offers performance that equals or exceeds that of popular general-purpose quads or bipolar of Bi-FET construction. On a 5-V supply the typical V/SUB os/ is 1 Mv, V/SUB os/ drift is 1.3 /spl mu/V//spl deg/C, 1-kHz noise is 36 nV//spl radic/Hz, and gain is one million into a 600-/spl Omega/ load. This device achieves its performance through circuit design and layout techniques as opposed to special analog CMOS processing, thus lending itself to use on system chips built with digital CMOS technology.     

On-chip high-voltage generation in MNOS integrated circuits using an improved voltage multiplier technique

An improved voltage multiplier technique has been developed for generating +40 V internally in p-channel MNOS integrated circuits to enable them to be operated from standard +5- and -12-V supply rails. With this technique, the multiplication efficiency and current driving capability are both independent of the number of multiplier stages. A mathematical model and simple equivalent circuit have been developed for the multiplier and the predicted performance agrees well with measured results. A multiplier has already been incorporated into a TTL compatible nonvolatile quad-latch, in which it occupies a chip area of 600 /spl mu/m/spl times/240 /spl mu/m. It is operated with a clock frequency of 1 MHz and can supply a maximum load current of about 10 /spl mu/A. The output impedance is 3.2 M/spl Omega/.     

On-chip high voltage charge pump in standard low voltage CMOS process

An on-chip high voltage tolerant 4VDD charge pump with symmetrical architecture in a standard low voltage 1.8 V 0.18 /spl mu/m CMOS process is presented. For a 250 k/spl Omega/ load, circuit efficiency of the charge pump is approximately 71%. All the MOS transistors satisfy typical voltage stress related reliability requirements for standard low voltage CMOS devices.     

A regulated charge pump with small ripple voltage and fast start-up

A regulated charge pump circuit is realized in a 3.3-V 0.13-/spl mu/m CMOS technology. The charge pump exploits an automatic pumping control scheme to provide small ripple output voltage and fast start-up by decoupling output ripple and start-up time. The automatic pumping control scheme is composed of two schemes, an automatic pumping current control scheme and an automatic pumping frequency control scheme. The former automatically adjusts the size of pumping driver to reduce ripple voltage according to output voltage. The latter changes the pumping period by controlling a voltage-controlled oscillator (VCO). The output frequency of the VCO varies from 400 kHz to 600 kHz by controlling the input bias voltage of the VCO. The prototype chip delivers regulated 4.5-V output voltage from a supply voltage of 3.3 V with a flying capacitor of 330 nF, while providing 30 mA of load current. The area is 0.25 mm/sup 2/ and the measured output ripple voltage is less than 33.8 mV with a 2-/spl mu/F load capacitor. The power efficiency is greater than 70% at the range of load current from 1 to 30 mA. An analytical model for ripple voltage and recovery time is proposed demonstrating a reasonable agreement with SPICE simulation results.     

A very high precision 500-nA CMOS floating-gate analog voltage reference

A floating gate with stored charge technique has been used to implement a precision voltage reference achieving a temperature coefficient (TC) <1 ppm//spl deg/C in CMOS technology. A Fowler-Nordheim tunnel device used as a switch and a poly-poly capacitor form the basis in this reference. Differential dual floating gate architecture helps in achieving extremely low temperature coefficients, and improving power supply rejection. The reference is factory programmed to any value without any trim circuits to within 200 /spl mu/V of its specified value. The floating-gate analog voltage reference (FGAREF) shows a long-term drift of less than 10 ppm//spl radic/1000 h. This circuit is ideal for portable and handheld applications with a total current of only 500 nA. This is done by biasing the buffer amplifier in the subthreshold region of operation. It is fabricated using a 25-V 1.5-/spl mu/m E/sup 2/PROM CMOS technology.     

A novel class of complementary folded-cascode opamps for low voltage

Three novel complementary folded-cascode operational amplifiers (opamps) with high gain, large bandwidth, and rail-to-rail input range for low-voltage operation will be presented. These opamps feature high bandwidth due to minimum internal nodes. The output swing is increased by properly adjusting the output cascode transistor gate voltages close to the power supply voltages. The opamps have been fabricated with a standard 0.8-/spl mu/m CMOS technology. Measurements show the amplification is between 60.1 and 72.4 dB, and the unity gain bandwidth is 14 MHz for a 5-pF load, 2.5-V power supply, and 150-/spl mu/A bias current.     

A realization of a below-1-V operational and 30-MS/s sample-and-hold IC with a 56-dB signal-to-noise ratio by applying the current-based circuit approach

This paper demonstrates the low-voltage and low-power operation of a MOS sample-and-hold circuit while preserving speed and accuracy, aiming at the realization of a pipelined low-voltage and low-power analog-to-digital converter on a system large-scale integrated circuit. It was fabricated by utilizing 0.35-/spl mu/m CMOS technology. The main feature of this circuit is that all the input, signals, and output are in the current form. The circuit consists of simple current mirrors. In order to eliminate the signal-dependent current transfer ratio error, voltages at the drain terminals of mirror transistors are fixed as constant. A source degeneration resistor, which is a transistor in the triode operational region, is connected to a mirror transistor in order to alleviate the influence of the threshold and transconductance parameter variations. Control signals are boosted in voltage and applied to the gate of switch NMOS transistors in the signal path in order to reduce the on-resistance of analog switches. A differential configuration is adopted throughout the entire circuit and effectively cancels switch feedthrough errors. As a result, a 30-MS/s operation with a signal-to-noise ratio (SNR) of 56 dB from a 1-V supply has been achieved, when the input current is /spl plusmn/200 /spl mu/A. The chip even operated down to 0.85 V with a 20-MHz clock. The SNR was measured as 50 dB with an input current of /spl plusmn/100 /spl mu/A.     

An efficient CMOS line driver for 1.544-Mb/s T1 and 2.048-Mb/s E1 applications

A CMOS operational amplifier (OPAMP) for use as a line driver for high-speed T1/E1 data communication link is described. The differential output swing, using a single 3.3-V power supply, is 5.2-V peak-to-peak on a 20-/spl Omega/ load. Novel circuits are used to control the closed-loop output impedance, quiescent bias current, and frequency compensation to ensure stable operation over varying temperature and load conditions. A special circuitry tristates the output in case of power-supply failure. The OPAMP achieves a unity-gain bandwidth of 35 MHz with only 10 mA of quiescent current. A new output-current-sense circuitry is used to provide a current feedback to adjust the output impedance for proper line termination as well as to provide short-circuit protection from excessive output currents. Using 0.35-/spl mu/m n-well CMOS technology, the amplifier occupies 0.69 mm/sup 2/ of area.     

A CMOS line driver for ADSL central office applications

An ADSL central office (CO) line driver utilizing a single 6-V supply is described. The line driver output produces a 20-V/sub ppd/ signal to deliver a 40-V/sub ppd/ swing to a 100-/spl Omega/ line. The adoption of an active termination, a dynamic supply control circuit technique, and deep n-well devices at the output stage of the line driver is key in achieving such a large voltage swing in a 0.25-/spl mu/m CMOS process. In order to ensure reliability of the output devices, the dynamic supply control algorithm is designed to activate only one lift amplifier at each signal path of the differential line driver at any given time. A transformer turns ratio of 1:2.4 ensures both reliability and optimal power dissipation in the presence of system losses. The total power dissipation of the line driver is 700 mW when discrete multitone signals with a crest factor of 15 dB were used to deliver 20.4 dBm to a 100-/spl Omega/ line.     

New low-voltage class AB/AB CMOS op amp with rail-to-rail input/output swing

A new low-voltage CMOS Class AB/AB fully differential opamp with rail-to-rail input/output swing and supply voltage lower than two V/sub GS/ drops is presented. The scheme is based on combining floating-gate transistors and Class AB input and output stages. The op amp is characterized by low static power consumption and enhanced slew-rate. Moreover the proposed opamp does not suffer from typical reliability problems related to initial charge trapped in the floating-gate devices. Simulation and experimental results in 0.5-/spl mu/m CMOS technology verify the scheme operating with /spl plusmn/0.9-V supplies and close to rail-to-rail input and output swing.     

Low-voltage CMOS current-mode preamplifier: analysis and design

This paper presents the analysis and design of a new low-voltage fully balanced differential CMOS current-mode preamplifier for multi-Gbps series data communications. The minimum supply voltage of the proposed preamplifier is V/sub T/+V/sub sat/. The preamplifier employs a balanced configuration to achieve large bandwidth and to minimize the effect of bias-dependent mismatches. Two new bandwidth enhancement techniques, namely inductive series peaking and current feedback that are specific to low-voltage CMOS current-mode circuits, are introduced. The inductive series peaking technique utilizes the resonant characteristics of LC networks to achieve both a flat frequency response and maximum bandwidth. Current feedback extends bandwidth, lowers input impedance, and improves dynamic range. The employment of both techniques further increases the bandwidth, reduces the value of the series peaking inductor, and improves noise performance of the pre-amplifier at high frequencies. The preamplifier has been designed using a 0.18-/spl mu/m 6-metal 1-poly 1.8-V CMOS technology. Simulation results from Spectre with BSIM3.3 device models that account for device parasitics demonstrate that the preamplifier has a flat frequency response with 25.3 dB dc current gain or equivalently 60 dB/spl Omega/ transimpedance gain with a 50-/spl Omega/ load and bandwidth of 2.15 GHz.     

A 24-GHz, +14.5-dBm fully integrated power amplifier in 0.18-/spl mu/m CMOS

A 24-GHz +14.5-dBm fully integrated power amplifier with on-chip 50-/spl Omega/ input and output matching is demonstrated in 0.18-/spl mu/m CMOS. The use of substrate-shielded coplanar waveguide structures for matching networks results in low passive loss and small die size. Simple circuit techniques based on stability criteria derived result in an unconditionally stable amplifier. The power amplifier achieves a power gain of 7 dB and a maximum single-ended output power of +14.5-dBm with a 3-dB bandwidth of 3.1 GHz, while drawing 100 mA from a 2.8-V supply. The chip area is 1.26 mm/sup 2/.     

Design of a low-power 3.5-GHz broad-band CMOS transimpedance amplifier for optical transceivers

This paper describes a novel low-power low-noise CMOS voltage-current feedback transimpedance amplifier design using a low-cost Agilent 0.5-/spl mu/m 3M1P CMOS process technology. Theoretical foundations for this transimpedance amplifier by way of gain, bandwidth and noise analysis are developed. The bandwidth of the amplifier was extended using the inductive peaking technique, and, simulation results indicated a -3-dB bandwidth of 3.5 GHz with a transimpedance gain of /spl ap/60 dBohms. The dynamic range of the amplifier was wide enough to enable an output peak-to-peak voltage swing of around 400 mV for a test input current swing of 100 /spl mu/A. The output noise voltage spectral density was 12 nV//spl radic/Hz (with a peak of /spl ap/25 nV//spl radic/Hz), while the input-referred noise current spectral density was below 20 pA//spl radic/Hz within the amplifier frequency band. The amplifier consumes only around 5 mA from a 3.3-V power supply. A test chip implementing the transimpedance amplifier was also fabricated using the low-cost CMOS process.     

A low-Voltage 10-bit CMOS DAC in 0.01-mm/sup 2/ die area

A low-voltage 10-bit digital-to-analog converter (DAC) for static/dc operation is fabricated in a standard 0.18-/spl mu/m CMOS process. The DAC is optimized for large integrated circuit systems where possibly dozens of such DAC would be employed for the purpose of digitally controlled analog circuit calibration. The DAC occupies 110 /spl mu/m/spl times/94 /spl mu/m die area. A segmented R-2R architecture is used for the DAC core in order to maximize matching accuracy for a minimal use of die area. A pseudocommon centroid layout is introduced to overcome the layout restrictions of conventional common centroid techniques. A linear current mirror is proposed in order to achieve linear output current with reduced voltage headroom. The measured differential nonlinearity by integral nonlinearity (DNL/INL) is better than 0.7/0.75 LSB and 0.8/2 LSB for 1.8-V and 1.4-V power supplies, respectively. The DAC remains monotonic (|DNL|<1 LSB) as INL reaches 4 LSB down to 1.3-V operation. The DAC consumes 2.2 mA of current at all supply voltage settings.     

A two-terminal IC temperature transducer

A bipolar monolithic IC temperature transducer with an operating temperature range of -125/spl deg/C to +200/spl deg/C has been designed, fabricated, and tested. The two-terminal device, which is fabricated using laser trimmed thin-film-on-silicon technology, is a calibrated temperature dependent current source with an average output impedence of 10 M/spl Omega/ over the 3.5-V to 30-V range of input voltage. Overall absolute accuracies of /spl plusmn/0.5/spl deg/C from -75/spl deg/C to +150/spl deg/C have been achieved on a scale of 1 /spl mu/A/K under optimum operating conditions.     

10-Gb/s limiting amplifier and laser/modulator driver in 0.18-/spl mu/m CMOS technology

A limiting amplifier incorporates active feedback, inductive peaking, and negative Miller capacitance to achieve a voltage gain of 50 dB, a bandwidth of 9.4 GHz, and a sensitivity of 4.6 mV/sub pp/ for a bit-error rate of 10/sup -12/ while consuming 150 mW. A driver employs T-coil peaking and negative impedance conversion to achieve operation at 10 Gb/s while delivering a current of 100 mA to 25-/spl Omega/ lasers or a voltage swing of 2 V/sub pp/ to 50-/spl Omega/ modulators with a power dissipation of 675 mW. Fabricated in 0.18-/spl mu/m CMOS technology, both prototypes operate with a 1.8-V supply.