Corrosion protection of AA 2024-T3 by bis-[3-(triethoxysilyl)propyl]tetrasulfide in sodium chloride solution.: Part 2: mechanism for corrosion protection

The corrosion protection of AA 2024-T3 by films of bis-[3-(triethoxysilyl)propyl]tetrasulfide (bis-sulfur silane) was studied in a neutral 0.6 M NaCl solution using potential transient, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The results showed that a highly crosslinked or dense interfacial layer that developed between the silane film and the aluminum oxide is the major contribution to the corrosion protection of AA 2024-T3. The formation of this interfacial layer heavily restricts pit growth underneath via retarding the transport of corrosion products, as well as effectively blocks a number of cathodic sites available for cathodic reactions.     

Corrosion Protection of AA2024-T3 by Cerium Malate and Cerium Malate-Doped Sol-Gel Coatings

Cerium malate (CeMal) was tested as a corrosion inhibitor for AA2024-T3 in this work. Corrosion inhibition on bare AA2024-T3 indicated that the inhibiting effect was a result of the synergistic effect of cerium cations and maleic anions. The corrosion of AA2024-T3 was stagnated by greatly reducing the corrosion current when CeMal was present in NaCl solutions. CeMal was adsorbed on the surface of AA2024-T3 forming a protective film in the initial stage. Then, cerium cations transformed to cerium oxide/hydroxides, precipitating on the cathode sites to inhibit the further corrosion. The electrochemical impedance spectra results of the sol-gel coatings proved that CeMal was an effective corrosion inhibitor in the sol-gel coatings to provide corrosion protection for AA2024-T3.     

Comparison of susceptibility to pitting corrosion of AA2024-T4, AA7075-T651 and AA7475-T761 aluminium alloys in neutral chloride solutions using electrochemical noise analysis

The susceptibility to pitting corrosion of AA2024-T4, AA7075-T651 and AA7475-T761 aluminium alloys was investigated in aqueous neutral chloride solution for the purpose of comparison using electrochemical noise measurement. The experimentally measured electrochemical noises were analysed based upon the combined stochastic theory and shot-noise theory using the Weibull distribution function. From the occurrence of two linear regions on one Weibull probability plot, it was suggested that there existed two stochastic processes of uniform corrosion and pitting corrosion; pitting corrosion was distinguished from uniform corrosion in terms of the frequency of events in the stochastic analysis. Accordingly, the present analysis method allowed us to investigate pitting corrosion independently. The susceptibility to pitting corrosion was appropriately evaluated by determining pit embryo formation rate in the stochastic analysis. The susceptibility was decreased in the following order: AA2024-T4 (the naturally aged condition), AA7475-T761 (the overaged condition) and AA7075-T651 (the near-peak-aged condition).     

Multifunctional epoxy coatings combining a mixture of traps and inhibitor loaded nanocontainers for corrosion protection of AA2024-T3

This work aims at investigating the corrosion protection effectiveness of multifunctional epoxy coatings modified with pigments such as ceramic nanocontainers loaded with corrosion inhibitor, chloride and water traps, applied on AA2024-T3. Characterizations on the morphology, composition and structure of the coatings were conducted. The corrosion resistance was studied by electrochemical impedance spectroscopy, localized electrochemical impedance spectroscopy and scanning vibrating electrode technique. The mechanical behaviour of the coatings was examined through nanoindentation and nanoscratching tests. Electrochemical and nanomechanical testing results, evidenced the improvement of the corrosion protective properties and mechanical behaviour of the coatings in the presence of the various pigments.     

Electrochemical study of modified cerium-silane bi-layer on Al alloy 2024-T3

In this paper, the performance of bis-1, 2-(triethoxysilyl) ethane (BTSE) as a pre-treatment to protect the AA 2024-T3 against corrosion has been investigated by electrochemical impedance spectroscopy (EIS), potentiodynamic polarization curves, and the scanning vibrating electrode technique (SVET). The microstructural and morphological characterizations were carried out via scanning electron microscopy and atomic force microscopy and the chemical composition evaluated using contact angle measurements and X-ray photoelectron spectroscopy (XPS). The electrochemical results showed that the additives improved the anticorrosion properties of the coating. The chemical characterization indicated that additives contribute to an increased degree of surface coverage, as well as to a more complete reticulation. The SVET results evidenced the self-healing abilities of Ce ions.     

Investigation of the corrosion behaviour of AA 2024-T3 in low concentrated chloride media

Aluminium alloy (AA) 2024-T3 is an important engineering material due to its widespread use in the aerospace industry. However, it is very prone to localized corrosion attack in chloride containing media, which has been mainly associated to the presence of coarse intermetallics (IMs) in its microstructure. In this work the corrosion behaviour of AA 2024-T3 in low concentrated chloride media was investigated using microscopy and electrochemical methods. TEM/EDS observations on non-corroded samples evidenced the heterogeneous composition within the IMs. In addition, SEM observations showed that intermetallics with the same nominal composition present different reactivity, and that both types of coarse IMs normally found in the alloy microstructure are prone to corrosion. Moreover, EDS analyses showed important compositional changes in corroded IMs, evidencing a selective dissolution of their more active constituents, and the onset of an intense oxygen peak, irrespective to the IM nature, indicating the formation of corrosion products. On the other hand, the results of the electrochemical investigations, in accordance with the SEM/EDS observations, evidenced that IMs corrosion dominates the electrochemical response of the alloy during the first hours of immersion in the test electrolyte.     

Mechanisms of corrosion inhibition of AA2024-T3 by vanadates

The mechanisms of corrosion inhibition of AA2024-T3 by vanadates were studied using chronoamperometry, polarization curves and adsorption isotherms. The electrochemical behaviour of clear solutions containing metavanadates and orange solutions containing decavanadates was clearly distinctive. Metavanadates reduced the kinetics of oxygen reduction to an extent similar to chromates. Corrosion inhibition of AA2024-T3 by metavanadates was very rapid and it might occur by the formation of an adsorbed layer. Reduction of clear metavanadate solution was very slow. Approximately 35 min were required to develop a monolayer of a reduced vanadate species. The adsorption of the inhibitor likely blocked reactive sites on intermetallic particles, discouraging the oxygen reduction reaction (ORR). Adsorption of the inhibitor on the Al matrix could also displace Cl⁻ ions, increasing the stability of the passive film and reducing the breakdown of S-phase particles. In contrast, decavanadates were shown to be poor inhibitors of the ORR. A sharp current spike was observed after injection of decavanadates for both Cu and AA2024-T3 at various applied cathodic potentials. Integration of the current peaks suggested the formation of several monolayers of a reduced vanadate species. The formation of several monolayers was in line with the poor performance of decavanadates as inhibitors of AA2024-T3 corrosion.     

Preparation and electrochemical characterization of amoxicillin-doped cellulose acetate films for AA2024-T3 aluminum alloy coatings

Cellulose acetate films doped with amoxicillin were deposited onto AA2024-T3 aluminum alloy and the corrosion protection in 0.05 M NaCl was evaluated by Electrochemical Impedance Spectroscopy (EIS) and the Scanning Vibrating Electrode Technique (SVET). The doping of the cellulose acetate film with amoxicillin resulted in a significant increase in the high frequency resistance and a decrease in the capacitance of the material. The protective effect could be observed under anodic polarization by way of a marked decrease in the anodic current. These results show the promising potential for the deposition of cellulose acetate films doped with amoxicillin onto AA2024-T3.     

Analytical characterisation and corrosion behaviour of bis-[triethoxysilylpropyl]tetrasulphide pre-treated AA2024-T3

This work aims at studying the corrosion behaviour of AA2024-T3 pre-treated with bis-[triethoxysilylpropyl]tetrasulphide. Simultaneously, the work investigates the influence of the Cu-rich intermetallic particles on the formation of the silane film. The analytical characterisation of the silane films was performed by Auger electron spectroscopy and X-ray photoelectron spectroscopy. The corrosion performance of the pre-treated substrates was evaluated by electrochemical impedance spectroscopy. Atomic force microscopy associated with Kelvin probe was also used to determine the influence of the silane film on the Volta potential distribution on the alloy surface. The results show that copper present in the intermetallics plays an important role on the film formation.     

Synergistic effect of pH and oxalate concentration on corrosion of aluminium alloy 2024-T3

This work aims at obtaining comprehensive information on the corrosion behaviour of AA2024-T3 in oxalic acid solutions under different concentrations (0.007–0.2?M) and pH (2–6). Various tests to characterise the corrosion behaviour are performed, including weight loss and electrochemical tests. Coupon surfaces are examined using infinite-focus microscopy, scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy, Raman spectroscopy and diffuse reflectance infrared Fourier transform spectroscopy. Corrosion rates, anodic and cathodic reaction kinetics are detailed to provide a fundamental understanding of the electrochemical behaviour of AA2024-T3 as a function of pH and oxalate concentration. The synergistic effect of pH and oxalate concentration on corrosion of AA2024-T3 is evaluated for both AA2024-T3 matrix and main intermetallics (i.e. Al–Cu–Mg and Al–Cu–Fe–Mn) and the electrochemical behaviour of each constituent element in AA2024-T3 is systematically studied.     

Corrosion protection of AA 2024-T3 by bis-[3-(triethoxysilyl)propyl]tetrasulfide in neutral sodium chloride solution. Part 1: corrosion of AA 2024-T3

This study consists of two parts. In the first part, the corrosion of 2024-T3 aluminum alloy (AA 2024-T3) was studied using scanning electron microscopy and energy-dispersive X-ray spectroscopy. The results showed that the anodic S phase (Al₂CuMg) particles dealloyed Al and Mg during the 3.5 h of immersion in a neutral 0.6 M sodium chloride (NaCl) solution; with the dealloying of Mg being the most severe. Simultaneously, a heavy dissolution was also observed for the surrounding Al matrix of the S phase particles. This Al dissolution is likely to be caused by a local alkalization resulting from the coupled cathodic reaction (water and/or oxygen reduction). Such corrosion in AA 2024-T3, however, can be inhibited efficiently after the treatment of bis-[3-(triethoxysilyl)propyl]tetrasulfide (bis-sulfur silane). The associated studies on bis-sulfur silane treated AA 2024-T3 will be presented in the second part.     

Photogenerated cathode protection properties of nano-sized TiO2/WO3 coating

Nano-sized TiO₂/WO₃ bilayer coatings were prepared on type 304 stainless steel substrate by sol-gel method. The performance of photo-electrochemical and photogenerated cathode protection of the coating was investigated by the electrochemical method. The results show that the bilayer coating with four TiO₂ layers and three WO₃ layers exhibits the highest photo-electrochemical efficiency and the best corrosion resistance property. Type 304 stainless steel with the coating can maintain cathode protection for 6 h in the dark after irradiation by UV illumination for 1 h. In addition, the mechanism of the photogenerated cathode protection for the bilayer coating was also explored.     

Electrochemical study of modified non-functional bis-silane layers on Al alloy 2024-T3

In the last few years great efforts have been made in order to find and to develop environmentally friendly substitutes for Cr⁶⁺ pre-treatments applied on aluminium alloys used in the aircraft industry. Among the potential substitutes, silane layers have attracted considerable interest from researchers and from the industry. The present work investigates the anti-corrosion behaviour of (bis-1, 2-(triethoxysilyl) ethane (BTSE)) silane layers modified with Ce ions and/or silica nanoparticles applied on Al alloy 2024-T3 substrates. The corrosion behaviour was investigated in 0.1 M NaCl solution via d.c. polarization and electrochemical impedance spectroscopy (EIS). Contact angle measurements and XPS were used to assess information on the chemistry of the silane pre-treated surfaces. The results have shown that the introduction of additives improves the corrosion protection properties of the silane layer.     

Influence of pre-treatments in cerium conversion treatment of AA2024-T3 and 7075-T6 alloys

The role of pre-treatment in the formation of a cerium conversion coating is investigated for the protection of AA2024-T3 and 7075-T6 alloys. The alloys were alkaline-etched and de-smutted in nitric acid, prior to cerium treatment in Ce(NO₃)₃ at 85 °C with H₂O₂ accelerator. Potentiodynamic polarization studies in 3.5% NaCl solution revealed a large shift of  300 mV of the corrosion potential below the pitting potential for the 7075-T6 alloy, which correlated with the development of a finely-textured, uniform coating. However, the formation of a uniform coating and protection was dependent upon the time of de-smutting, with non-uniform coatings resulting from extended times of de-smutting. In contrast, non-uniform coatings developed on the 2024-T3 alloy, with pitting potential at the corrosion potential, irrespective of the time of de-smutting. Findings for the 2024-T3 alloy indicate that extended de-smutting affects the enrichment of alloying elements.     

Corrosion protection of aluminium alloy 2024-T3 in 0.05 M NaCl by cerium cinnamate

The corrosion protection of AA 2024-T3 in 0.05 M NaCl by cerium cinnamate has been studied. Polarization measurements demonstrate that cerium cinnamate is markedly effective for suppressing anodic process of the alloy corrosion during the initial 72 h of immersion. The protection mechanism during the immersion period appears to involve two stages: the deposition of cerium cinnamate, and then hydrolysis of cerium ions forming a cerium oxide/hydroxide, prevailing over the foregoing deposition. This study also elucidates the inhibition effect of cerium cinnamate on the early corrosion attack occurred from the second phase particles by X-ray photoelectron spectroscopy and electron-probe microanalysis.     

Preparation,Surface Characterization and Anticorrosive Behavior of Polyaniline and Poly(3,4-ethylenedioxythiophene) Deposited on Aluminum Alloy AA2024-T3

This work is focused on studying the preparation and characterization of two different conducting polymers, polyaniline and poly(3,4-ethylenedioxythiophene), on aluminum alloy AA2024-T3. In addition to the direct electrochemical deposition of the conducting polymers onto an untreated aluminum substrate, the alloy surface pre-treatments based on single chemical acid pickling or chemical acid pickling followed by application of self-assembled monolayers have been also considered before the coating application. Coatings electrochemically deposited onto both untreated and pre-treated substrates have been characterized by physicochemical and electrochemical techniques, whereas their protective performance has been evaluated by means of polarization electrochemical techniques and accelerated corrosion tests. Although conducting polymers are widely used as protective coatings for steel substrates, the results obtained in this work indicate that their protective effect is not improved when deposited onto aluminum.     

The effect of inhibitor structure on the corrosion of AA2024 and AA7075

A range of structurally-related compounds were tested for their capacity to inhibit corrosion on aluminium alloys AA2024-T3 and AA7075-T6 in 0.1 M NaCl solution. It was found that the thiol group, positions para- and ortho- to a carboxylate, and substitution of N for C in certain positions strongly inhibited corrosion. The hydroxyl group was slightly inhibitive, while the carboxylate group provided little or no corrosion inhibition on its own. In several cases, different activities were found on the different alloys, with some compounds (particularly thiol-containing compounds) being more effective on AA2024 than on AA7075.     

Electrochemical study of inhibitor-containing organic-inorganic hybrid coatings on AA2024

Use of organic-inorganic hybrid sol-gel thin films is recently reported among the most promising approaches for the replacement of chromate based pre-treatment methods for high strength structural aluminium parts.To be applied in the aerospace industry, pre-treatments have to meet the demanding requirements and must be compatible to state of the art paint systems. The addition of inhibitive species is desirable for the active corrosion protection and the prevention of sub-surface migration at defect sites of the coating.In the present work hybrid films were produced by the controllable sol-gel route. Corrosion inhibitors were incorporated to the coatings in order to provide active protective effect. The barrier properties and the active corrosion protection on AA2024-T3 have been studied by Electrochemical Impedance Spectroscopy and Scanning Vibrating Electrode Technique. The obtained results were proven by conventional accelerated tests such as neutral salt spray test confirming validity of the mentioned electrochemical techniques for the evaluation of protection efficiency of hybrid sol-gel films.The addition of inhibitors to sol-gel coatings in most cases leads to an improvement of the active corrosion protection but on the other hand it may negatively influences the barrier properties of the films. Therefore, encapsulation of the inhibiting compounds is beneficial in order to combine the good barrier function of the coating with the corrosion mitigating effect of the inhibitors.     

Microstructure, spallation and corrosion of plasma sprayed Al2O3–13%TiO2 coatings

The electrochemical corrosion behaviours of the steel substrates coated with three different plasma sprayed Al₂O₃–13%TiO₂ coatings were studied in this paper. The three kinds of Al₂O₃–13%TiO₂ coatings were conventional ME coating, nanostructured NP coating and NS coating. There were micro cracks, laminar splats and straight columnar grains in ME coating. For the two nanostructured coatings, the laminar microstructure and columnar grains were not obvious. The NP coating had the highest hardness and spallation resistance. Electrochemical corrosion behaviour of the three coatings was mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in aqueous Na₂SO₄ solution.     

Comparison of the corrosion resistance of an Al–Cu alloy and an Al–Cu–Li alloy

ABSTRACT

In this study, the corrosion mechanisms of the AA2024-T3 and the AA2098-T351 were investigated and compared using various electrochemical techniques in 0.005?mol?L^?1 NaCl solution. The severe type of corrosion in the AA2098-T351 was intragranular attack (IGA) although trenching and pitting related to the constituent particles were seen. On the other hand, the AA2024-T3 exhibited severe localised corrosion associated with micrometric constituent particles, and its propagation was via grain boundaries leading to intergranular corrosion (IGC). Electrochemical techniques showed that the corrosion reaction in both alloys was controlled by diffusion. The non-uniform current distribution in both alloys showed that EIS was not a proper technique for comparing the corrosion resistance of the alloys. However, local electrochemical techniques were useful for the evaluation of the corrosion resistance of the alloys.