The initial stage of pitting corrosion on coated steels investigated by photon rupture in chloride containing solutions

A photon rupture method, film removal by a focused pulse of pulsed Nd-YAG laser beam irradiation, has been developed to enable oxide film stripping at extremely high rates without contamination from the film removal tools. In the present study, Zn-55mass%Al alloy and Al-9mass%Si alloy-coated steel specimens covered with protective nitrocellulose film were irradiated with a focused pulse of a pulsed Nd-YAG laser beam at a constant potential in 0.5 kmol m⁻³ H₃BO₃-0.05 kmol m⁻³ Na₂B₄O₇ (pH = 7.4) with 0.01 kmol m⁻³ of chloride ions to investigate the initial stage of localized corrosion. At low potentials, oxide films on both coated alloys were reformed after the nitrocellulose films were removed by this method. The oxide film formation kinetics follows an inverse logarithmic law, in agreement with Cabrera-Mott theory. However, at high potentials, localized corrosion producing corrosion products occurs at the area where nitrocellulose film was removed. Nevertheless, when the applied potential is less noble, the dissolution current of the Zn-55mass%Al-coated steel samples is higher than that of Al-9mass%Si-coated samples.     

Preparation of ultrathin polymer coatings adsorbed on iron via a covalent bond by multistep modification of a hydroxymethylbenzene SAM with ethoxysilanes and alkanediol for preventing iron corrosion in 0.5 M NaCl

The film thickness, d of a p-hydroxymethylbenzene - C₆H₄CH₂OH (HOMB) self-assembled monolayer (SAM) adsorbed on iron via a covalent bond was increased by multistep modification with tetraethoxysilane (C₂H₅O)₄Si (TES) and 1,8-octanediol HO(CH₂)₈OH (C₈DO) and subsequently with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ (BTESE) and akyltriethoxysilane C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18). The protective ability of the film against iron corrosion was examined by polarization measurement of the iron electrode coated with the film in an oxygenated 0.5 M NaCl after immersion in the solution for many hours. The values of protective efficiency, P for the films, the HOMB SAM modified with TES and C₈DO twice and subsequently with BTESE and C_nTES were high, more than 81% at n = 8 and 85% at n = 18 in the range of the immersion time, t up to 240 h, respectively. The maximal P values of the respective films were 88.0% and 92.2%, of which approximate d values were 4.6 and 5.8 nm. The high protection of iron against corrosion was attributed to increases in the film thickness and interconnection between the adsorbed molecules with Si-O polymer linkages. The protective ability of the film was remarkably persistent during immersion in the solution for many hours. A slight enhancement of P was observed by additional modification of the modified HOMB SAM with C₈TES due to increases in interconnection and close packed arrangement. The formation of strong adsorption bonds, σ-covalent bond and back-donating π-bond, between the carbon atom of HOMB moiety and iron atom was discussed.     

H2S and O2 influence on the corrosion of carbon steel immersed in a solution containing 3 M diethanolamine

Aqueous solutions with 3 mol L⁻¹ (M) diethanolamine (DEA) concentration are extensively used in the gas processing industry to remove acid gases. However, the degradation of the DEA and the formation of heat-stable salts (HSS) lead to severe corrosion problems. Even worse, equipment corrosion can be magnified by the unavoidable presence of sulphide acid and dissolved oxygen as a result of hydrocarbon (natural gases and crude oil) processing. The aim of this work is to study the combined corrosion effects of DEA, sulphide acid and oxygen on carbon steel. Electrochemical methods revealed that in the 3 M DEA medium without oxygen, corrosion processes are modulated by adsorbed DEA film formation. Furthermore, it was shown that the addition of oxygen and 15 × 10⁻³ mol L⁻¹ (15 mM) H₂S produced the formation of an adherent film on the carbon steel surface. Chemical analyses by EDAX revealed a homogeneous film of corrosion products composed of iron oxide and sulphide formed in DEA solution containing O₂ and H₂S, respectively. Equivalent circuits were used to estimate the parameters associated with ion diffusion through the formed corrosion films. The results showed that the presence of H₂S induced the formation of thin iron sulphide films that provide protective properties to the metal. It is concluded that the presence of oxygen in a sweetening plant should be avoided as DEA degradation can be produced with the subsequent decrease in chelating process efficiency and the increase in corrosion problems.     

Additional modification to two-dimensional polymer films of a hydroxymethylbenzene self-assembled monolayer with alkyltriethoxysilanes for enhancing the protective abilities against iron corrosion

Additional modification of the ultrathin two-dimensional polymer film, a p-hydroxymethylbenzene C₆H₄CH₂OH self-assembled monolayer modified with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ (BTESE) and alkyltriethoxysilane C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18), was attempted to improve the protective ability of the film against iron corrosion. The ability of the film was examined by polarization measurement of an iron electrode coated with the film in an oxygenated 0.5 M NaCl solution after immersion in the solution for 1.5 to 72 h. Marked improvement of the protective efficiency, P was not obtained by additional modification to the polymer film with BTESE. The P values of the two-dimensional polymer films were markedly increased by additional modification with C₈TES. The increases in P were ascribable to improvement of alkyl tail arrangement and additional interconnection in the polymer films. The film on the iron surface was characterized by contact angle measurement, FTIR reflection spectroscopy and X-ray photoelectron spectroscopy. The protective abilities of the two-dimensional polymer films additionally modified with C₈TES were persistent during immersion for 72 h.     

Corrosion prevention of passivated iron in 0.1 M NaCl by coverage with an ultrathin polymer coating and healing treatment in 0.1 M NaNO3

An ultrathin, ordered and two-dimensional polymer coating was prepared on a passivated iron electrode by modification of 16-hydroxyhexadecanoate ion HO(CH₂)₁₅CO₂⁻ self-assembled monolayer with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. Subsequently, the electrode was healed in 0.1 M NaNO₃. Protection of passivated iron against passive film breakdown and corrosion of iron was examined by monitoring of the open-circuit potential and repeated polarization measurements of the polymer-coated and healed electrode in an aerated 0.1 M NaCl solution during immersion for many hours. Localized corrosion was markedly prevented by coverage with the polymer coating and the healing treatment in 0.1 M NaNO₃. Prominent protection of iron from corrosion in 0.1 M NaCl was observed before the breakdown occurred. The electrode surface covered with the healed passive film and polymer coating was analyzed by contact angle measurement, X-ray photoelectron spectroscopy and electron-probe microanalysis.     

Prevention of passive film breakdown and corrosion of iron in 0.1 M KClO4 with and without Cl by covering with an ultrathin two-dimensional polymer coating and healing treatment in 0.1 M NaNO3

A two-dimensional polymer coating, the self-assembled monolayer of 16-hydroxy hexadecanoate ion HO(CH₂)₁₅ modified with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃ was prepared on the passivated iron electrode and further, the passive film was healed by additional treatment in 0.1 M NaNO₃. This electrode was immersed in oxygenated 0.1 M KClO₄ solutions with and without 1 × 10⁻⁴ to 1 × 10⁻² M of Cl⁻. Protection of passive film against breakdown by covering the electrode with the polymer coating was examined by monitoring the open-circuit potential during immersion in the solutions for many hours to determine the time for passive film breakdown, t_bd. Repeated polarization measurements were carried out during immersion in these solutions for obtaining the protective efficiency, P. The t_bd value of the passivated, polymer-coated and healed electrode in 0.1 M KClO₄ solutions with and without Cl⁻ increased with a decrease in the concentration of Cl⁻. No breakdown occurred on the electrode during immersion in 0.1 M KClO₄ solutions with and without 1 × 10⁻⁴ of Cl⁻ for 360 h. The P values were extremely high, more than 99.9% before t_bd, indicating complete protection of iron from corrosion. The effect of healing treatment in 0.1 M NaNO₃ on passive film breakdown was investigated by electron-probe microanalysis.     

Protection of iron against corrosion by coverage with ultrathin two-dimensional polymer films of a hydroxymethylbenzene self-assembled monolayer anchored by the formation of a covalent bond

Ultrathin films of two-dimensional polymers were prepared on an iron electrode by modification of a p-hydroxymethylbenzene p-HOCH₂C₆H₄ (HOMB) self-assembled monolayer (SAM) with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ (BTESE) and alkyltriethoxysilanes C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 and 18). The electrode was derivatized by cathodic reduction of p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄ in an electrolytic acetonitrile solution below 10 °C for 1 h to form the SAM via a covalent bond between carbon and iron atoms. The protective ability of the polymer film against iron corrosion was determined by polarization measurement of the coated electrode in an oxygenated 0.5 M NaCl solution. The protective efficiencies of the polymer films prepared by modification with BTESE plus C₈TES and C₁₈TES were 63.9% and 68.5% after immersion in 0.5 M NaCl for 1.5 h, respectively. These values were higher than those of the one-dimensional polymer films prepared with the respective C_nTES. The film of the HOMB SAM modified with BTESE plus C₈TES was characterized by contact angle measurement using a drop of water and X-ray photoelectron and FTIR reflection spectroscopies. The films of the HOMB SAM modified with BTESE plus C₈TES and C₁₈TES were persistent during immersion of the coated electrodes in 0.5 M NaCl for many hours by far as compared with the alkanethiol SAM anchored on iron by the formation of a coordinate bond.     

Synergistic corrosion inhibition study of Armco iron in sodium chloride by piperidin-1-yl-phosphonic acid-Zn system

Electrochemical techniques, weight loss method and surface analysis were used to study the synergistic inhibition offered by Zn²⁺ and piperidin-1-yl-phosphonic acid (PPA) to the corrosion of Armco iron in 3% chloride solution. It is observed that the combination between PPA and Zn²⁺ shows excellent inhibition efficiency. The potentiodynamic polarization curves reveal that 5 × 10⁻³ mol l⁻¹ of PPA has only 76.7% inhibition efficiency whereas the mixture containing 5 × 10⁻³ mol l⁻¹ PPA -20%Zn²⁺ has 90.2% inhibition efficiency. This suggests that a synergistic effect exists between Zn²⁺ and PPA. The Fourier transform infrared (FTIR) spectrum of the film formed on iron indicates phosphonates zinc salt formation. A suitable mechanism of corrosion inhibition is proposed based on the results obtained. The surface film analysis showed that in the absence of Zn²⁺, the protective film consists of Fe²⁺-PPA complex formed on the anodic sites of the metal surface, whereas in the presence of Zn²⁺, the protective film consists of Fe²⁺-PPA complex and Zn(OH)₂.     

An ultrathin polymer coating of carboxylate self-assembled monolayer adsorbed on passivated iron to prevent iron corrosion in 0.1 M Na2SO4

For preparing an ultrathin two-dimensional polymer coating adsorbed on passivated iron, a 16-hydroxyhexadecanoate ion HO(CH₂)₁₅CO₂⁻ self-assembled monolayer (SAM) was modified with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. Protection of passivated iron against passive film breakdown and corrosion of iron was investigated by monitoring of the open-circuit potential and repeated polarization measurements in an aerated 0.1 M Na₂SO₄ solution during immersion for many hours. The time required for passive film breakdown of the polymer-coated electrode was markedly higher in this solution than that of the passivated one, indicating protection of the passive film from breakdown by coverage with the polymer coating. The protective efficiencies of the passive film covered with the coating were extremely high, more than 99.9% in 0.1 M Na₂SO₄ before the passive film was broken down, showing prominent cooperative suppression of iron corrosion in the solution by coverage with the passive film and polymer coating. The polymer-coated surface was characterized by contact angle measurement and electron-probe microanalysis (EPMA). Prevention of passive film breakdown and iron corrosion for the polymer-coated electrode healed in 0.1 M NaNO₃ was also examined in 0.1 M Na₂SO₄.     

Corrosion inhibition of carbon steel in tetra-n-butylammonium bromide aqueous solution by benzotriazole and Na3PO4

The corrosion inhibition behavior of benzotriazole, Na₃PO₄ and their mixture on carbon steel in 20 wt.% (0.628 mol l⁻¹) tetra-n-butylammonium bromide aerated aqueous solution was investigated by weight-loss test, potentiodynamic polarization measurement, electrochemical impedance spectroscopy and scanning electron microscope/energy dispersive X-ray techniques. The inhibition action of BTA or SP or inhibitors mixture on the corrosion of carbon steel is mainly due to the inhibition of anodic process of corrosion. The results revealed that inhibitors mixtures have shown synergistic effects at lower concentration of inhibitors. At 2 g l⁻¹ BTA and 2 g l⁻¹ SP showed optimum enhanced inhibition compared with their individual effects.     

The chain length influence of cationic surfactant and role of nonionic co-surfactants on controlling the corrosion rate of steel in acidic media

The corrosion inhibition effect of cationic surfactants, DTAB (Dodecyl Trimethyl Ammonium Bromide) and TTAB (Tetradecyl Trimethyl Ammonium Bromide), on low carbon steel was studied using weight loss, open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) measurements. The effect of chain length compatibility on corrosion inhabitancy of surfactant and co-surfactant was investigated by C₇OH (1-heptanol), C₁₂OH (1-dodecanol) and C₁₅OH (1-pentadecanol) as nonionic co-surfactants in acidic media at different concentrations of DTAB and TTAB. Data represented that the corrosion rate decreased by increasing concentration of DTAB and TTAB, independently. The effect of chain length compatibility on surfactant behavior was discussed. Decreasing of corrosion rate for DTAB + C₁₂OH was more pronounced than other mixtures.     

Corrosion behavior of glassy Ni55Co5Nb20Ti10Zr10 alloy in 1 N HCl solution studied by potentiostatic polarization and XPS

Corrosion resistance of glassy Ni₅₅Co₅Nb₂₀Ti₁₀Zr₁₀ (at.%) alloy in 1 N HCl solution was investigated with respect to the electrochemical behavior and the compositions of the passive film and the underlying alloy surface just below the passive film. The potentiostatic polarization curve indicated that the alloy was spontaneously passivated with a low passive current density of the order of 10⁻³ A m⁻². The quantitative X-ray photo-electron spectroscopy (XPS) analysis revealed that the thickness of the surface film increased linearly with an anodizing ratio of 1.5 nm V⁻¹. The high corrosion resistance of the glassy alloy was due to the formation of niobium, titanium and zirconium-enriched passive film. The growth mechanism of the passive films is also discussed.     

Formation, fast oxidation and thermodynamic data of Fe(II) hydroxychlorides

Iron(II) hydroxide and hydroxychloride precipitates were obtained by mixing FeCl₂ · 4H₂O and NaOH aqueous solutions with various concentration ratios R′ = [Cl⁻]/[OH⁻] = 2 [FeCl₂]/[NaOH] at [NaOH] = 0.4 mol L⁻¹. They were analysed by Infrared spectroscopy after 24 h of ageing at room temperature. Fe(OH)₂ was obtained alone only for the smallest values of R′, typically R′ ? 1.16. β-Fe₂(OH)₃Cl formed as soon as R′ ? 1.40 and was obtained alone for R′ ? 2.25. The initial precipitates were oxidised by addition of a small amount of hydrogen peroxide (5 mL of an aqueous solution containing approximately 30 vol% H₂O₂) instead of O₂. The action of H₂O₂ on Fe(OH)₂ gave rise to δ-FeOOH as already reported. Its action on Fe(II) hydroxychlorides gave rise to akaganéite β-FeO_1−2x(OH)_1+xCl_x. A transformation of the two-phase system found at R′ = 1.5 after long ageing times (6 months) was observed and β-Fe₂(OH)₃Cl remained alone. This slow transformation of Fe(OH)₂ into β-Fe₂(OH)₃Cl may explain why β-Fe₂(OH)₃Cl was only reported as a corrosion product on iron archaeological artefacts. Finally, the respective domains of stability of Fe(OH)₂ and β-Fe₂(OH)₃Cl were demarcated and an estimation of the standard Gibbs free energy of formation of β-Fe₂(OH)₃Cl could be given: .     

The inhibition activity of ascorbic acid towards corrosion of steel in alkaline media containing chloride ions

The activity of ascorbic acid towards steel corrosion in saturated Ca(OH)₂ solution containing chloride ions was investigated in this study. Concentration and time dependence of the protective properties of the passive film were acquired by electrochemical impedance spectroscopy. The best inhibitive performance, i.e. the longest pitting initiation time was obtained in the presence of 10⁻³ M ascorbic acid, while both lower and higher concentrations showed shortening of the pitting-free period. The overall behaviour of ascorbic acid was attributed to its ability to form chelates of various solubility having various metal/ligand ratios and oxidation states of the chelated iron. The assumption of ascorbic acid assisted reductive dissolution of the passive layer at higher inhibitor concentrations was confirmed by cyclic voltammetry and ATR FTIR spectroscopy. It is proposed that the overall inhibitive effect at lower concentrations is due to the formation of insoluble surface chelates and the effective blocking of the Cl⁻ adsorption at the surface of passive film. A pronounced inhibitive effect observed after the pitting had initiated was ascribed to the formation of a resistive film at the pitted area.     

Preparation of one-dimensional polymer films by modification of a hydroxymethylbenzene self-assembled monolayer on iron with alkyltriethoxysilanes for preventing iron corrosion

A self-assembled monolayer (SAM) of p-hydroxymethylbenzene HOCH₂C₆H₄ - (HOMB) moiety adsorbed on iron by the formation of a covalent bond between carbon and iron atoms was prepared by electrochemical derivatization of an iron electrode with p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄. The electrode covered with the HOMB SAM was modified with alkyltriethoxysilanes C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18) to prepare a film of one-dimensional polymer. The protective ability of the polymer film was determined by polarization measurement of the covered electrode in an aerated 0.5 M NaCl solution. The ability was enhanced by modification of the HOMB SAM with C_nTES markedly. The iron surface coated with the one-dimensional polymer film of the HOMB SAM modified with C₈TES was characterized by contact angle measurement and FTIR reflection and X-ray photoelectron spectroscopies. The persistence in the protective ability of the polymer film against iron corrosion in 0.5 M NaCl may be associated with the strong adsorption via the covalent bond, revealed by electron-probe microanalysis.     

Environmental factors affecting the corrosion behavior of reinforcing steel II. Role of some anions in the initiation and inhibition of pitting corrosion of steel in Ca(OH)2 solutions

Potential-time curves are constructed for the steel electrode in naturally aerated Ca(OH)₂ solutions simulating the corrosion behavior in concrete. Cl⁻ and SO₄²⁻ ions cause the destruction of passivity and initiation of pitting corrosion. The rate of oxide film growth by Ca(OH)₂ and oxide film destruction by Cl⁻ and SO₄²⁻ ions follows a direct logarithmic law as evident from the linear relationships between the open-circuit potential and the logarithm of immersion time. Chromate, phosphate, nitrite, tungstate and molybdate ions inhibit the pitting corrosion of steel. The rate of oxide film healing and thickening increases with their concentrations. In presence of constant inhibitor concentration, the efficiency of pitting inhibition increases in the order: (weak) CrO₄²⁻ < HPO₄²⁻ < NO₂⁻ < WO₄²⁻ < MoO₄²⁻ (strong).     

Effect of carbon on corrosion and passivation of iron in hot concentrated NaOH solution in relation to caustic stress corrosion cracking

Quenched Fe-C materials with up to 0.875 wt.% C were examined in 8.5 M NaOH at 100 °C to better understand the effect of carbon on caustic stress corrosion cracking (SCC) of plain steels. Carbon at contents up to about 0.23 wt.% C accelerated anodic dissolution of iron, whereas at high contents it hindered corrosion and promoted the formation of magnetite. It is suggested that carbon particles on the corroding surface form confined regions with an increased concentration of H⁺ and HFeO₂⁻, thereby favouring the formation of Fe₃O₄. Intergranular SCC can be explained by preferred anodic dissolution of grain boundary material enriched in carbon.     

Gamma-radiation-induced corrosion of carbon steel in neutral and mildly basic water at 150 °C

The effect of γ-radiation on the kinetics of carbon steel corrosion has been investigated by characterizing the oxide films formed on steel coupons at 150 °C and at two pH values. Results show that continuous irradiation enhances surface oxide formation with the type of oxide formed dependant on the solution pH. For experiments at 150 °C and a [OH⁻] equivalent to that for pH_{25 °C} = 10.6, the surface oxide on carbon steel after γ-irradiation was non-porous and uniform, and no localized corrosion was observed. This oxide, however, appears to be susceptible to brittle fracture during cooling. Raman spectroscopy of the surface film indicates that it is a mixture of the phases of Fe₃O₄ and γ-Fe₂O₃. In contrast, at 150 °C with [OH⁻] equivalent to neutral pH_{25 °C}, metal dissolution is significant and the surface oxide film is very porous. Raman spectra show that this oxide film is also composed of a mixture of Fe₃O₄ and γ-Fe₂O_3. The results from this work combined with previously reported electrochemical studies of the same system as a function of pH and temperature can be used to deconvolute the effects of radiation, pH and temperature on the nature of the corrosion process.     

The electroplated palladium-copper alloy film on 316L stainless steel and its corrosion resistance in mixture of acetic and formic acids

Palladium-copper alloy films (Cu 2.93-5.66 at.%) were deposited on 316L stainless steel by electroplating. The films showed good adhesive strength and increased surface micro-hardness. In boiling mixture of 90% acetic acid + 10% formic acid + 400 ppm Br⁻ under stirring (625 r/min), the Pd-Cu films showed better corrosion resistance than Pd film. The Pd-5.66%Cu films showed the lowest corrosion rate almost three orders of magnitude lower than that of 316L matrix. The increased corrosion resistance of Pd-Cu films was attributed to the improved passivity, better barrier effect, increased surface hardness and the effect of Cu to resist pitting.     

An AFM Study of corrosion on rigid magnetic disks

The corrosion susceptibility of a cobalt-based magnetic alloy as a function of overcoat film thickness at 20 °C and 50% relative humidity is investigated using atomic force microscopy. The overcoat films include ion beam-deposited nitrogenated carbon (IBDN), and sputter-deposited silicon carbide (SiC) and silicon nitride (SiN_x). In all cases, corrosion decreases with increasing overcoat film thickness. The critical overcoat film thickness for corrosion inhibition is approximately 25, 25 and 20 Å for IBDN, SiC and SiN_x, respectively. However, larger corrosion particles are found for IBDN and SiC with increasing thickness just below the critical thickness for coverage.