Corrosion Resistance on High Strength Bainitic Steel and 09CuPCrNi After Wet-Dry Cyclic Conditions

The accelerated wet-dry cyclic corrosion tests have been carried out of a high strength bainitic steel and 09CuPCrNi. The results indicated that the corrosion resistance of 09CuPCrNi was better than that of the bainitic steel based on the mass loss measurements. The morphology and composition of the rusting products have been investigated in order to realize the mechanism of rust formation on the two steels. The rust scale on both steels was composed of a dense inner layer and a loose outer layer. The inner layer grew thicker and denser as the test proceeding. Both of inner and outer layers were mainly composed of magnetite (Fe3O4) and maghemite (γ-Fe2O3) with a small amount of lepidocrocite (γ-FeOOH) and akaganeite (β-FeOOH). The rust phase of γ-Fe2O3 was detected in a higher amount of the inner layer, resulting in a much denser inner layer. The inner rust layer of 09CuPCrNi being denser and thicker than that of the high strength bainitic steel was attributed to the alloying elements such as copper, chromium and phosphorus enriched in it. The protective inner rust layer plays an important role in the corrosion resistance of the steel.     

E690海洋平台用钢力学性能和海洋大气腐蚀行为

以传统的E36海洋平台钢为对比钢,研究三种E690海洋平台钢的组织和力学性能,以及模拟海洋大气环境下的腐蚀行为.通过失重法测得实验钢在不同腐蚀时间下的腐蚀速率,利用扫描电镜和X射线衍射仪观察并测定了锈层的形貌特征和相组成,采用电子背散射衍射技术对实验钢的晶界类型进行分析.结果表明:以贝氏体组织为特征的E690海洋平台钢具有优异的力学性能,-40℃的冲击值超过了200 J;晶界类型主要为3°~15°的亚晶界和大于50°的大角度晶界;E690海洋平台钢周浸16 d后的锈层致密且腐蚀速率已趋于稳定,最低腐蚀速率为0.84 mm·a-1,远低于组织为铁素体+珠光体钢的1.4 mm·a-1,实验钢的锈层主要由Fe₃O₄、α-FeOOH、β-FeOOH及γ-FeOOH四种晶态相和非晶无定形物组成.通过分析得出,热处理工艺和组织构成对材料的初期腐蚀行为有重要影响,而化学成分和锈层自身的致密性对材料后期腐蚀行为起决定作用.      

Cr对低合金钢在流动NaCl溶液中耐蚀性的影响

对碳钢和Cr含量不同的实验钢在流速为0.8m/s的流动的3.5％(质量分数)NaCl溶液中的腐蚀行为进行研究,最长腐蚀周期为192h.对4种实验钢的腐蚀失重进行了比较,并利用动电位极化曲线、SEM、EPMA和TEM等分析手段,对实验钢表面形成锈层的特征进行了系统研究.结果表明,含Cr实验钢的腐蚀失重低于碳钢,并且随Cr的质量分数由0.5％提高至2％,腐蚀失重亦降低.Cr元素在内锈层中的富集是含Cr钢耐蚀性改善的重要原因.这种富集可使腐蚀产物颗粒获得细小的尺寸,致密内锈层形成的原因就是由于这种尺寸细小的腐蚀产物的形成,使内锈层的保护性获得明显的改善.     

Cr对流动NaCl溶液中普碳钢锈层特征的影响

对碳钢和耐蚀管用含Cr低合金钢进行流动加速腐蚀实验,研究了实验钢在流动腐蚀性条件下的锈层结构以及Cr元素对锈层的影响机理.利用极化曲线、SEM、TEM及XPS等分析手段研究了Cr元素对实验钢耐流动加速腐蚀性的影响,以及含Cr钢内锈层的腐蚀形貌,深入分析了Cr在内锈层中的分布及存在状态.结果表明,含Cr钢内锈层致密均匀,Cr元素在内锈层中富集并以Fe2CrO4的形式存在.Fe2CrO4细小的颗粒尺寸是形成致密内锈层的原因,致密的内锈层对基体具有很好的保护作用.     

低合金耐候钢在含氯离子环境中的腐蚀行为

利用干湿周浸加速腐蚀实验对比研究了低合金钢A588和SPA-H在含氯离子环境下腐蚀行为,并利用金相显微镜、扫描电镜、X射线衍射和电子探针等方法分析了Ni、Mn对于低合金钢腐蚀行为的影响.结果表明:实验钢锈层中的物质主要由α-FeOOH、γ-FeOOH和Fe₃O₄组成,但其含量存在差异;Ni元素在内锈层含量高于外锈层,Mn元素在锈层的孔洞处富集;内锈层的致密程度高于外锈层;提高合金元素Mn和Ni的含量,可以提高内锈层的致密性,从而提高低合金钢的耐蚀性能.      

Effect of Cr on Characteristic of Rust Layer Formed on Low Alloy Steel in Flow-accelerated Corrosion Environment

The flow-accelerated corrosion experiments were carried out to research the effect of Cr on the rust layers formed on the carbon steel and Cr-containing steel,as well as the structure of rust layer of the two experimental steels.The influence of Cr on the flow-accelerated corrosion resistance and the corrosion morphology of inner rust layer formed on the Cr-containing steel were studied by the methods of polarization curves,scanning electron microscope,transmission electron microscope,and X-ray photoelectron spectroscope.The distribution of Cr and its form of existence in the inner rust layer were analyzed.The results show that corroded mass loss of Cr-containing steel is lower than that of carbon steel and its inner rust layer is compact.Cr exists in the form of Fe2CrO4 and is enriched in the inner rust layer.This concentration could make the inner rust layer exhibit the tendency of amorphous.This phenomenon is related to fine Fe2CrO4.The inner rust layer becomes more compact because of the formation of fine Fe2CrO4,and the protectiveness of inner rust layer could be improved remarkably.     

Corrosion Resistance of High Performance Weathering Steel for Bridge Building Applications

 The mechanical properties, corrosion resistance and microstructures of high performance steel (HPS) was investigated by tensile testing machine, Charpy V-Notch (CVN) testing machine, cyclic immersion corrosion tester, XRD, optical microscopy (OM), scanning electron microscopy (SEM), and electron probe micro-analyzer (EPMA). The results showed that significant differences existed in the tensile strength, yield strength and impact toughness between HPS and PCS. After 72 h cyclic immersion accelerated corrosion test, the inner rust layer on HPS was composed of α-FeOOH phase and denser than that on PCS that was a mixture of α-FeOOH and Fe3O4. The rust formed on HPS provides better protection and HPS has lower corrosion rates than PCS. Copper and chromium in HPS enrich in the rust layer and enhance the compactness of the rust layer. Based on the results of the accelerated corrosion tests and rust layer analysis, the roles of Cu and Cr against corrosion are discussed, providing HPS with chemical specification which has been industrially successful to produce weathering steel for bridge structure.     

Rusting Evolution of MnCuP Weathering Steel Submitted to Simulated Industrial Atmospheric Corrosion

The rusting evolution of MnCuP weathering steel in a simulated industrial atmosphere as a function of corrosion duration was investigated by corrosion weight gain, scanning electron microscopy, X-ray diffraction, and electrochemical methods. The results indicate that the corrosion kinetics is related closely to the rust composition and electrochemical properties. The corrosion rate is higher during the first corrosion stage, and it is lower during the second corrosion stage. During the first corrosion stage, the rust layer is in low density, discontinuous, and loose, with a lower relative abundance of α-FeOOH. During the second corrosion stage, a compact and protective inner rust layer forms with a higher relative abundance of α-FeOOH, contributing to enhanced rust layer resistance. The rust initially enhances and then stabilizes the cathodic process, but the anodic process tends to be inhibited by the protective rust layer. Electrochemical impedance spectroscopy tests indicate that it is more scientific to evaluate the rust layer protective ability by charge transfer resistance.     

耐候钢锈层及其稳定化处理现状

耐候钢具有良好的耐大气腐蚀性,但是稳定化锈层形成较慢,在耐候钢使用前对表面进行预处理,可以缩短锈层稳定化形成时间和防止锈液流挂.简要概述了国内外耐候钢的发展情况,以及耐候钢稳定化锈层的形成过程和锈层的组成与结构,分为以γ-FeOOH为主的疏松外锈层和以α-FeOOH为主的致密内锈层;介绍了表面锈层保护机理,包括物理阻隔...     

Cr-Ni-Cu系低合金铸钢在海洋大气环境中的腐蚀行为

为满足桥梁支座用铸钢在海洋大气环境下的耐蚀性要求,设计了2种成分的Cr-Ni-Cu系耐腐蚀低合金铸钢。采用周浸加速腐蚀试验、实地大气暴露试验考察试验钢在海洋大气环境中的腐蚀行为,并结合扫描电镜、XRD、电化学手段分析了合金元素对锈层和电化学行为的影响。结果表明,2种成分的Cr-Ni-Cu系低合金铸钢的耐蚀性均较好,随着时间延长,耐蚀铸钢腐蚀率下降并达到稳定,而对比钢种20MnSi腐蚀率保持下降趋势,未达到稳定状态。周浸腐蚀316h后耐蚀铸钢与20MnSi腐蚀率差距变小;Cr元素在内锈层中呈条带状富集,有效阻碍了Cl-的扩散,Ni的加入提高钢的自腐蚀电位,促进γ-FeOOH向α-FeOOH的转化,增加锈层稳定性;Cr、Ni、Cu的复合加入增大了铸钢的电荷传递电阻,提高了耐蚀性。     

湿热海洋大气中SO2污染对Q235B钢腐蚀行为的影响

 以NaCl和NaHSO3为介质,采用干/湿周浸加速腐蚀试验、腐蚀失重分析、XRD、SEM等,研究了湿热海洋大气中SO2对Q235B钢腐蚀行为的影响。结果表明,SO2污染使Q235B钢的腐蚀明显加重。污染前后,Q235B钢的腐蚀过程均遵循幂函数[W＝Atn]的分布规律,腐蚀产物均由非晶和少量Fe3O4、α-FeOOH、β-FeOOH、γ-FeOOH晶体组成,但参数[A、][n]值和晶体数量并不相同。Cl－和SO2在腐蚀过程中具有协同作用,但作用机理不同。Cl－会阻止腐蚀产物吸附,并促使其脱落,进而阻止保护性锈层形成;而SO2在酸化过程中会与钢基体和锈层反应,进而破坏锈层结构,加剧钢的腐蚀。SO2还能抑制β-FeOOH并促进α-FeOOH的生成,进而抑制Cl－的破坏作用并改善锈层的稳定性;但随锈层增厚,SO2的抑制作用减弱,内锈层随之变疏松。     

超低碳高强度耐候钢腐蚀性能的研究

通过显微组织观察、周浸加速腐蚀试验、锈层微观分析、Χ射线衍射等方法,以商业CortenB钢为对比钢,研究了超低碳高强度耐候钢(ULCW)的腐蚀性能。结果表明:超低碳高强度耐候钢的耐腐蚀性能优于CortenB钢;ULCW钢在腐蚀过程中能快速形成致密锈层,提高了钢的耐腐蚀性能;ULCW钢锈层中保护性产物α-FeOOH的量明显多于CortenB钢,提高了对钢基体的保护作用。     

集装箱钢板在湿热海洋大气环境中的腐蚀行为

研究了集装箱钢板在西沙海洋大气环境中暴露不同阶段的腐蚀行为。采用SEM（EDS）、XRD研究了锈层形貌及成分,采用极化曲线研究了暴露不同阶段的腐蚀电化学行为。通过腐蚀深度测试,建立了腐蚀速率与暴露时间的幂指数关系,结合腐蚀形貌和产物分析,主要的锈蚀产物为γ FeOOH、β FeOOH。Cr和Cu合金元素也参与了锈层的形成,有助于提高锈层的致密性。电化学测试结果表明,耐候钢暴露不同阶段的腐蚀电流,3个月时值最低,6个月随后暴露时间增加,锈层不断增厚,起到对Cl 的阻碍作用,降低腐蚀速率;之后随着曝露时间的增加,锈层出现脱落,腐蚀速率随之增加。     

Influence of Chromium on Mechanical Properties and CO2/H2S Corrosion Behavior of P110 Grade Tube Steel

Four kinds of P110 grade tube steels containing different chromium contents were designed to probe the in- fluence of Cr on the properties of tube steel. The microstrueture, mechanical properties and corrosion behavior of the four kinds of P110 grade tube steels were studied deeply and thoroughly. The analysis of the mechanical properties indicated that tensile strength and yield strength of the steel plates were improved, while transverse and longitudinal impact energy and elongation first increased and then decreased when Cr content rose. The impact energy and elonga tion reached the peak when Cr content was 1 ~. Cr precipitates were found only in 3 ~ Cr steel, with （Nb, Ti）（C, N） or Nb（C,N） as the core of precipitation and then grew up. The corrosion experiments demonstrated that the scales on the four steels had a two layer structure under the corrosion of CO2 and H2 S. The outer layer was mainly com- posed of FeS or FeS1 x and the inner layer consisted of FeCOa and Cr compounds. Cr was rich in the inner layer and the Cr content of the inner layer increased with the Cr content in matrix. The enriched Cr enhanced the compactness of the scales, further hindering the diffusion of ions from liquid to the surface of steel, thus reducing corrosion rate.     

Q235钢在实际土壤与模拟溶液中的腐蚀行为

对比分析了Q235钢在实际土壤和模拟溶液中的腐蚀行为,计算了其腐蚀失重,利用SEM和XRD方法分析了两种腐蚀介质中Q235钢的锈层形貌、物相结构及相对含量,并分析了不同介质中材料的极化曲线。结果表明:Q235钢在两种不同腐蚀介质中的腐蚀行为存在较大差异。Q235钢在模拟溶液中的腐蚀速率远高于实际土壤,至周期360h达到0.413mm/a,约为实际土壤的4.5倍;Q235钢在实际土壤中呈蚀斑相连长大扩展的腐蚀形貌,其腐蚀产物为α-FeOOH、γ-FeOOH、Fe3O4和Fe2O3;模拟溶液中试样为均匀腐蚀形貌,阴极过程主要受析氢控制;随腐蚀周期的延长,内锈层中生成结晶性良好的Fe3O4,降低了试样的腐蚀速率。     

低碳钢在湿热工业海洋大气中的腐蚀特征

以0.1 mol·L-1NaCl+0.01 mol·L-1 NaHSO₃溶液为腐蚀介质,采用干/湿周浸加速腐蚀实验、腐蚀失重、X射线衍射、扫描电镜和能谱分析等方法,研究了湿热工业海洋大气中低碳钢的腐蚀行为.结果表明:实验钢的腐蚀过程均遵循幂函数d=Atn分布规律,钢种不同,常系数A、n的值不同;腐蚀产物主要由非晶物质和少量Fe₃O₄、α-FeOOH、β-FeOOH、γ-FeOOH晶体组成.所得锈层可分为主体锈层和界面疏松带两部分,由内至外锈层中Fe、O含量梯度变化很小.Cl-、SO₂与水分的长期协同作用会导致内锈层结构变差,而添加稳定性或耐蚀性较高的元素可以改善锈层质量,进而增强钢材的耐腐蚀性能.      

Influence of Cr on reduction behavior of rust formed on low alloy steels in flowing 3. 5% NaCl solution

The reduction behavior of rust layer formed on carbon steel and on Cr- containing steels was investigated in flowing 3. 5mass% NaCl solution via potentiodynamic polarization curve, EPMA, XRD, and XPS. The results show that the weight loss of Cr- containing steels is lower than that of carbon steel. Fe3+ in the rust layer participated in the cathodic reaction with the corrosion process. Cr concentrated in the inner rust layer formed on the experimental steels, and exited in the form of Cr3+. This concentration behavior of Cr increases the corrosion potential of experimental steels and decreases the amount of Fe3O4 in the inner rust layer. Inhibition of reduction of rust results in a decrease of corrosion of metal. Moreover, inhibition of rust reduction suppresses the reduction reaction of oxygen, owing to the decrease of conductivity of rust layer. Therefore, the corrosion resistance of experimental steels can be improved by suppressing the cathodic reaction in flowing 3. 5 mass% NaCl solution.     

pH值对Q235钢在模拟酸性土壤中腐蚀行为的影响

通过腐蚀失重计算、扫描电镜、X射线衍射方法、极化曲线分析等手段,研究了pH值对Q235钢在模拟酸性土壤中腐蚀行为的影响.在模拟酸性土壤环境中,Q235钢的腐蚀速率随土壤pH值升高而降低,经360 h腐蚀后,在pH值为4.0、4.5和5.1的土壤中试样的腐蚀速率分别为0.68、0.48和0.42 mm·a-1.随土壤pH值升高,Q235钢锈层更为致密,其表面蚀坑由窄深型发展变为宽浅型发展.腐蚀产物均为SiO₂、α-FeOOH、γ-FeOOH、Fe₂O₃及Fe₃O₄,随土壤pH值升高,腐蚀产物中α-FeOOH/γ-FeOOH质量比升高.极化曲线分析表明,随土壤pH值升高,Q235钢腐蚀电位升高,自腐蚀电流密度降低,试样腐蚀速率减小.      

稀土对低碳钢耐工业大气腐蚀性的影响

研究了在江津地区暴晒2年低碳钢和稀土钢的大气腐蚀行为。结果表明:稀土可以有效提高低碳钢耐工业大气腐蚀性,试验钢的腐蚀数据符合动力学模型D=Atn。采用扫描电镜、极化曲线、XRD及Fourier变换红外光谱等手段对腐蚀产物进行研究。发现稀土能促进稳定的保护性腐蚀产物α-FeOOH生成,降低锈层中具有反应活性的Fe3O4含量;并可以增加锈层致密性。从锈层反应的角度阐述了稀土提高低碳钢耐蚀性的机理。     

��H2S��ʪ���滷���´�����ʴ���о�

The corrosion environment of cargo oil tank (COT) was simulated according to performance standard for corrosion resistant steel of IMO in this paper, to study the corrosion behavior of two different ship hull steel on the upper deck of COT. The results showed general corrosion in wet-dry environments contained H2S, the corrosion rate of conventional E36 steel reached 0??4mm/a. The addition of Cu and Ni improved the formation of the stable phase ??-FeOOH, which decreased the defect in the rust and made the rust more compact. Inclusions such as CaO and CaS formed in the Ca treated ship steel, which dissolved under the corrosion media and alkaline product generated, the alkaline product increased the pH value of the liquid film on the surface of steel and slowed down the corrosion rate of steel.