The nature of the third-element effect in the oxidation of Fe-xCr-3 at.% Al alloys in 1 atm O2 at 1000 °C

The oxidation of an Fe-Al alloy containing 3 at.% Al and of four ternary Fe-Cr-Al alloys with the same Al content plus 2, 3, 5 or 10 at.% Cr has been studied in 1 atm O₂ at 1000 °C. Both Fe-3Al and Fe-2Cr-3Al formed external iron-rich scales associated with an internal oxidation of Al or of Cr+Al. The addition of 3 at.% Cr to Fe-3Al was able to stop the internal oxidation of Al only on a fraction of the alloy surface covered by scales containing mixtures of the oxides of the three alloy components, but not beneath the iron-rich oxide nodules which covered the remaining alloy surface. Fe-5Cr-3Al formed very irregular external scales where areas covered by a thin protective oxide layer alternated with others covered by thick scales containing mixtures of the oxides of the three alloy components, undergrown by a thin layer rich in Cr and Al, while internal oxidation was completely absent. Conversely, Fe-10Cr-3Al formed very thin, slowly-growing external Al₂O₃scales, providing an example of third-element effect (TEE). However, the TEE due to the Cr addition to Fe-3Al was not directly associated with a prevention of the internal oxidation of Al, but rather with the inhibition of the growth of external scales containing iron oxides. This behavior has been interpreted on the basis of a qualitative oxidation map for ternary Fe-Cr-Al alloys taking into account the existence of a complete solid solubility between Cr₂O₃ and Al₂O₃.     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

Effect of tin on high-temperature sulphidation of Fe-Cr alloys in H2/H2S atmospheres

The high temperature sulphidation behaviour of Fe-46Cr-xSn (x = 0; 0.2; 0.5; 1; 2) alloys has been studied at temperatures of 1073, 1173 and 1273 K in H₂/H₂S mixtures with different sulphur vapour partial pressures of 10⁻¹, 10⁻³ and 10⁻⁵ Pa. Thermogravimetric studies in combination with scanning electron microscope (SEM), with energy dispersive spectrometer (EDS), and X-ray diffraction (XRD) techniques, have displayed a significant influence of the sulphur partial pressure on the composition and growth rate of the sulphide scale. The results have shown that addition of tin increases the sulphidation rate of Fe-46Cr alloys but not considerably (except at temperatures of 1073 and 1173 K combined with sulphur partial pressure of 10⁻⁵ Pa). The metallic core of the studied samples was enriched in tin and iron, moreover tin was found in the internal layer close to the metallic core as metallic Fe_xSn_y inclusions with tin concentrations of up to 12 at.%.     

Corrosion behavior of three iron-based model alloys in reducing atmospheres containing HCl and H2S at 600 °C

The corrosion of three Fe-xCr alloys (x = 8, 12, 18 wt.%) was examined at 600 °C in reducing atmospheres containing HCl and H₂S with two different H₂S contents and compared with the behavior of the same materials in H₂S-free H₂-CO₂ and H₂-HCl-CO₂ mixtures producing similar oxygen and chlorine pressures. Exposure to the low-H₂S gas mixture had only a reduced effect on the behavior of Fe-8Cr and Fe-18Cr, but increased significantly the corrosion rate of Fe-12Cr. Increasing the H₂S level accelerated the corrosion of all the alloys, but particularly that of Fe-18Cr. In both cases only minor amounts of sulfur and chlorine were present close to the alloy/scale interface. An increase of the Cr content reduced the corrosion rate in both H₂S gas mixtures, especially in the range 8-12 wt.% Cr, due to a larger volume fraction of Cr₂O₃ in the scale. The results have been discussed on the basis of the thermodynamic stability diagrams of the Fe-O-Cl-S and Cr-O-Cl-S systems.     

Electrochemical passive properties of AlxCoCrFeNi (x = 0, 0.25, 0.50, 1.00) alloys in sulfuric acids

This study investigates the electrochemical passive properties of Al_xCoCrFeNi alloys in H₂SO₄ by potentiodynamic polarization, EIS, and weight loss tests from 20 to 65 °C. Experimental results indicate that Al harms the corrosion resistance in H₂SO₄ at temperatures exceeding 27 °C owing to the porous and inferior nature of the protection oxide film of Al in these alloys. Closely examining the Arrhenius plots of corrosion current density reveals that both pre-exponential factor A and activation energy E_a increase with Al content. However, A affects corrosion current density more significantly than E_a at higher temperatures and, conversely, at lower temperatures.     

Comparison of the corrosion of Cu50Pd50 and Cu50Pd44M6 (M = Y,Mg, or Al) hydrogen separation membrane alloys in simulated syngas containing H2S

The resistance to sulfidation was examined by exposing coupons including a Cu–Pd binary alloy and three ternary alloys with 6 at% Y, Mg, or Al to simulated syngas containing varying amounts of H₂S. The mass change of the samples was determined and the exposed surfaces were characterized by SEM/EDS and XRD. The best corrosion resistance of the ternary alloys was observed in the Cu₅₀Pd₄₄Al₆ alloy. A slight decrease was observed when Mg was added, but both the Al and Mg alloys were roughly on par with the binary composition. The Y addition resulted in a degradation in the corrosion resistance by forming extensive internal Y₂O₃ and Cu_1−xY_xS and external Pd_4−xCu_xS and Pd ₁₃Cu₃S₇.     

Microstructure and oxidation behaviour of Ir-rich Ir–Al binary alloys

In the current study, alloys of Ir–11Al, Ir–23Al, Ir–30Al, Ir–41Al and Ir–45Al (at.%) were prepared to investigate the microstructure and oxidation behaviour of Ir-rich Ir–Al alloys. Ir(Al)_ss and/or β-IrAl intermetallic phases were found to exist in the prepared alloys. During isothermal oxidation at 1100 °C, the Ir(Al)_ss and β-IrAl individually changed to porous and dense Al₂O₃. The microstructure of the oxide scale formed on Ir–23Al was similar to that of its former alloy which possessed a dendrite-like configuration. It was found that the mass change of Ir–45Al followed a parabolic law, showing the best oxidation resistance among the Ir–Al alloys.     

High temperature scaling of Ni-xSi-10 at.% Al alloys in 1 atm of pure O2

The oxidation of Ni-xSi-10Al alloys (with x = 0, 2, 4 and 6 at.%), has been studied at 900 and 1000 °C in 1 atm of pure O₂ to examine the effect of different silicon additions on the behavior of ternary Ni-Si-10Al alloys. The kinetic curves of Ni-10Al are approximately parabolic at both 900 and 1000 °C. Conversely, the kinetics of the ternary alloys at both temperatures correspond generally to a rate decrease faster than predicted by the parabolic rate law, except for the oxidation of Ni-6Si-10Al at 1000 °C, which exhibits a single nearly-parabolic stage. Oxidation of the binary alloy formed at both temperatures an internal oxidation zone beneath a layer of NiO. Oxidation of Ni-2Si-10Al at both temperatures and of the other two alloys at 900 °C formed initially a zone of internal oxidation of Al + Si. However, a layer of alumina forming at the front of internal oxidation after some time blocked the internal oxidation and produced a gradual conversion of the metal matrix of this region into NiO, with a simultaneous decrease of the oxidation rate. Conversely, the oxidation of Ni-4Si-10Al and Ni-6Si-10Al at 1000 °C did not produce an internal oxidation, but formed an alumina layer directly on the alloy surface after an initial stage when also Ni was oxidized. Therefore, silicon exerts the third-element effect by reducing the critical Al content needed for the transition from its internal to its external oxidation with respect to the corresponding Ni-Al alloy. This result is interpreted by means of an extension to ternary alloys of Wagner’s criterion for the same transition in binary alloys based on the attainment of a critical volume fraction of internal oxide.     

High temperature corrosion of pure Fe, Cr and Fe-Cr binary alloys in O2 containing trace KCl vapour at 750 °C

Pure Fe, Cr and Fe-Cr binary alloys were corroded in O₂ containing 298 ppm KCl vapour at 750 °C. The corrosion kinetics were determined, and the microstructure and the composition of oxide scales were examined. During corrosion process, KCl vapour reacted with the formed oxide scales and generated Cl₂ gas. As Cl₂ gas introduced the active oxidation, a multilayer oxide scales consisted of an outmost Fe₂O₃ layer and an inner Cr₂O₃ layer formed on the Fe-Cr alloys with lower Cr concentration. In the case of Fe-60Cr or Fe-80Cr alloys, monolayer Cr₂O₃ formed as the healing oxidation process. However, multilayer Cr₂O₃ formed on pure Cr.     

Electrochemical response of AlNiLa amorphous and devitrified alloys

The electrochemical response of Al_94−xNi₆La_x alloys (x = 4, 5, 6, 7) after different stages of devitrification was studied in 0.05 M Na₂SO₄ as well as in different concentrations [0.001 M, 0.01 M and 0.1 M] NaCl solutions. Complementary crystallization studies were carried out to elucidate the composition dependent phase evolution in these alloys. It was observed that the primary crystallization did not cause any deterioration in the corrosion resistance of the alloys as compared to the amorphous alloys. In the case of Al₈₇Ni₆La₇, there was actually an improvement in the passivating ability in benign media. The various primary crystalline phases in the different alloys investigated did not cause different electrochemical responses. However, the onset of secondary crystallization caused a reduction in the corrosion resistance in the NaCl media through a loss in passivating ability of all the alloys. This is due to increased galvanic activity as well as the loss of the amorphous phase.     

The oxidation of two ternary Fe-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of two ternary Fe-Cu-Al alloys containing 10 at.% Al (Fe-65Cu-10Al and Fe-30Cu-10Al) has been studied at 800-900 °C under 1 atm O₂. Under all conditions both alloys show an initial faster stage during which Fe-65Cu-10Al corrodes more rapidly at 800 °C than at 900 °C, while Fe-30Cu-10Al follows nearly identical kinetics at both temperatures. As oxidation proceeds, a continuous alumina layer is eventually established on the surface of the two alloys, thus decreasing significantly their oxidation rates. Altogether, the Fe-rich alloy Fe-30Cu-10Al oxidizes slightly faster than the Cu-rich alloy Fe-65Cu-10Al at both temperatures. The possible reasons for the decrease in the critical Al content needed to form external alumina scales for the Cu-rich alloy in comparison with binary Cu-Al alloys are examined.     

Influence of rare earth metals on the characteristics of anodic oxide films on aluminium and their dissolution behaviour in NaOH solution

The characteristics of oxide films on Al and Al1R alloys (R = rare earth metal = Ce, Y) galvanostatically formed (at a current density of 100 μA cm⁻²) in borate buffer solution (0.5 M H₃BO₃ + 0.05 M Na₂B₄O₇·10H₂O; pH = 7.8) were investigated by means of electrochemical impedance spectroscopy. EIS spectra were interpreted in terms of an “equivalent circuit” that completely illustrate the Al(Al1R alloy)/oxide film/electrolyte systems examined. The resistance of the oxide films was found to increase on passing from Al to Al1R alloys while the capacitance showed an opposite trend. The stability of the anodic oxide films grown in the borate buffer solution on Al and Al1R alloys was investigated by simultaneously measuring the electrode capacitance and resistance at a working frequency of 1 kHz as a function of exposure over a period of time to naturally aerated 0.01 M NaOH solution. Analyses of the electrode capacitance and resistance values indicated a decrease in chemical dissolution rate of the oxide films on passing from Al to Al1R alloys.     

Criteria for the formation of protective Al2O3 scales on Fe-Al and Fe-Cr-Al alloys

The conditions for the formation of external alumina scales on binary Fe-Al alloys and the nature of the third-element effect due to chromium additions have been investigated by studying the oxidation at 1000 °C in 1 atm O₂ of a binary Fe-10 at.% Al alloy (Fe-10Al) and of two ternary Fe-Cr-10 at.% Al alloys containing 5 and 10 at.% chromium (Fe-5Cr-10Al and Fe-10Cr-10Al, respectively). An Al-rich scale developed initially on Fe-10Al was subsequently replaced by a multi-layered scale containing mixtures of Fe and Al oxides plus a large number of Fe-rich oxide nodules: internal aluminum oxidation was essentially absent from this alloy. Addition of 5 at.% chromium to Fe-10Al did not suppress the formation of nodules, but they were eventually healed by the growth of an alumina layer at their base, resulting in a significant reduction of the oxidation rate. Finally, the alloy with 10 at.% Cr formed continuous external alumina scales without any Fe-rich nodule. Thus, the addition of sufficient amounts of chromium to Fe-10Al produces a third-element effect as expected. However, the process found in this alloy system does not involve a prevention of the internal oxidation of Al. Instead, it shows a transition from the growth of mixed Fe- and Al-rich external scales directly to an external Al₂O₃ scale formation. An interpretation of this kind of mechanism involving a third-element is presented along with a prediction of the critical Al contents required to produce the various possible scaling modes on binary Fe-Al alloys.     

Corrosion resistance of dilute CuMg alloys at elevated temperature

In comparison with CuAl (Al: 0.2 and 0.5 wt.%) alloys, corrosion resistance (CR) of CuMg (Mg: 0.12 and 0.34 wt.%) alloys was studied at 673-1173 K in atmospheric O₂. All the samples were pre-annealed at 873 K in atmospheric H₂. The CR of CuMg alloys at 673-973 K is improved in contrast to a pure Cu but much poorer than that of CuAl alloys, while the improvement can hardly be observed for CuMg alloys at and above 1073 K, which is similar to CuAl alloys. The poorer CR of CuMg alloys compared with that of CuAl alloys at 673-973 K is largely attributed to the incorporation of Cu in the MgO surface layer and the low Pilling-Bedworth ratio of CuMg-O system smaller than unity, and the vanishing of CR for CuMg alloys at and above 1073 K is ascribed to the instability of the MgO layer at the Cu₂O/CuMg interface.     

Electrochemical behaviour of Ni-base alloys exposed under oil/gas field environments

The electrochemical behaviour of Ni-base alloys (Inconel 625, Inconel 718, G3 and Incoloy 825) is carried out at 80 °C in CO₂/H₂S corrosion environments using cyclic potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS) techniques. The passivity mechanisms are analysed and discussed. In addition, some significant characterisation parameters such as E_corr, I_pass, E_pit, E_pp, ΔE and I_pass in cyclic polarisation curves are analysed and compared to reveal the corrosion resistance of various Ni-base alloys. The equivalent circuit model and ZsimpWin software are utilised to discuss the Nyquist plots of various Ni-base alloys. The diffusion mechanism in EIS measurement is discussed. The result shows that the corrosion resistance of the Ni-base alloys to CO₂ corrosion or CO₂/H₂S corrosion follows the sequence: Inconel 625 > G3 > Inconel 718 > Incoloy 825. H₂S works as a cathodic depolariser with accelerating initiation of the corrosion process.     

The effect of Si additions on the high temperature oxidation of a ternary Ni-10Cr-4Al alloy in 1 atm O2 at 1100 °C

The oxidation of four Ni-10Cr-ySi-4Al alloys was studied at 1100 °C to examine the effects of Si additions (from 2 to 6 at.%) on the behavior of the alloy Ni-10Cr-4Al. Addition of 2 at.% Si prevented completely nickel oxidation, but could not form alumina scales. Larger Si additions produced alumina only over part of the alloy surface (about 20% with 4 at.% Si and 30% with 6 at.% Si), but could not prevent completely the internal oxidation of Al. The results are interpreted by extending to quaternary alloys the mechanism of the third-element effect already proposed for ternary alloys.     

The effects of Cr and Al concentrations on the oxidation behavior of oxide dispersion strengthened ferritic alloys

The oxidation of six oxide dispersion strengthened (ODS) ferritic alloys was investigated at 1050 °C in air up to 200 h. Al plays the dominant role in improving the oxidation resistance of the ODS alloys. Cr and Y are of importance in forming the stable Al₂O₃ scale. To produce the dense alumina layer with enhanced adherence to the metal substrate, the concentrations of Al and Cr should be larger than 2 and 14 wt.%, respectively.     

Effect of copper on metal dusting of austenitic stainless steels

Three steels, 304SS, 310SS and 800H, were alloyed with 5%, 10%, and 20% (by weight) copper, and then exposed to 68%CO-31%H₂-1%H₂O gas at 680 °C (a_C = 19 and p_O2=5.4×10^-25 atm) under thermal cycling conditions. Kinetic measurements showed that copper-free alloys all dusted, with 304SS experiencing the greatest metal wastage. Copper additions did not have any effect on metal wastage of 304SS, but reduced the attack on 310SS and 800H markedly at levels of 5% and 10%. However, increasing the copper content to 20% produced large copper-rich precipitates which accelerated dusting by promoting internal graphitisation.Dusting was associated with surface coking. When pitting occurred, on copper-free alloys and on copper containing 304SS, large coke structures grew above the pits. Internal grain boundary carburisation always took place, and intragranular carbides also precipitated when dusting occurred. A lamellar surface layer of internally precipitated spinel and austenite also developed in association with dusting. The copper effect is discussed in terms of its alloy solubility and its known beneficial effect in Ni-Cu binaries.     

Corrosion behaviour of Al/Al3Ti and Al/Al3Zr functionally graded materials produced by centrifugal solid-particle method: Influence of the intermetallics volume fraction

Intermetallic particles, Al₃Ti and Al₃Zr were formed in Al–5mass%Ti and Al–5mass%Zr alloys, respectively, by centrifugal casting, in order to create functionally graded materials (FGMs). At present, no information is available on the influence of the amount of intermetallics on the electrochemical properties of these alloys.In this paper, the corrosion resistance of Al/Al₃Ti and Al/Al₃Zr FGMs was investigated by open-circuit measurements, potentiodynamic polarization and electrochemical impedance spectroscopy. Results suggests that the corrosion resistance of the FGMs is affected by galvanic effects between the intermetallic particles and the metallic matrix. Lower centrifugal forces resulted in an improvement of the electrochemical properties.     

Cyclic oxidation of high temperature coatings on new γ′-strengthened cobalt-based alloys

An emerging class of cobalt-based γ′-strengthened alloys promises higher temperature capabilities compared to current Ni-base superalloys commonly used in aerospace and power generation applications. As with Ni-base alloys, high temperature coatings that enhance environmental resistance are desirable. Single crystal samples of Co–9.2Al–9.0W and Co–7.8Al–7.8W–4.5Cr–2.0Ta (at.%) were coated with vapour phase nickel aluminide and MCrAlY. Samples were subjected to cyclic oxidation at 1100 °C with 300–450 1-h cycles. Compared to NiAl-based coatings, the MCrAlY coatings exhibited superior adherence and an interdiffusion zone free of detrimental intermetallic phases. Evolution of microstructure during cycling is discussed with reference to the available thermodynamic data.