Comparison of corrosion pitting under immersion and salt-spray environments on an as-cast AE44 magnesium alloy

The corrosion mechanisms of pitting, intergranular corrosion, and general corrosion were examined on an AE44 magnesium alloy subjected to immersion and salt-spray environments. The two environments show similar trends with respect to weight loss and thickness loss, although the immersion environment induces greater amounts of weight loss of magnesium. With respect to the corrosion mechanisms, the two environments show definitive trends, owing to the continuous presence of water in the immersion environment allowing more and larger pits to form as compared to the salt-spray environment. The immersion environment was more deleterious than the salt-spray environment for magnesium.     

Structure–property quantification of corrosion pitting under immersion and salt-spray environments on an extruded AZ61 magnesium alloy

Extruded AZ61 magnesium coupons were exposed to immersion and cyclical salt spray environments over 60 h in order to characterize their corrosion rates. The characteristics of general corrosion, pitting corrosion, and intergranular corrosion were quantified at various intervals. General corrosion was more prevalent on the immersion surface. In addition, more pits formed on the immersion surface due the continuous exposure to water and chloride ions. However, the pits on the salt spray surface showed larger surface areas, larger volumes, and covered more area on the micrographs as compared to the pits on the immersion surface, due to the dried pit debris that trapped chloride ions within the pits.     

Corrosion of magnesium alloy ZE41 - The role of microstructural features

Magnesium alloy ZE41, used extensively in the aerospace industry, possesses excellent mechanical properties albeit poor corrosion resistance. This paper investigates the mechanism of corrosion and the interaction between the grain boundary intermetallic phases, the Zr-rich regions within the grains and the bulk Mg-rich matrix. The results of optical and scanning electron microscopy (SEM) together with energy-dispersive X-ray (EDX) and atomic force microscopy (AFM) potential map measurements have shown the importance of the microstructure in the initiation and propagation of corrosion in an aqueous environment, indicating that the Zr-rich regions play a distinct role in the early stages of corrosion in this alloy.     

Corrosion of heat treated magnesium alloy ZE41

This paper investigates the effect of heat treatment upon the corrosion morphology and mechanism of ZE41 alloy. The results of optical and scanning electron microscopy (SEM) together with potentiodynamic polarisation reveal the importance of the microstructure in the initiation and propagation of corrosion in an aqueous environment. The corrosion of the heat-treated alloy is significantly altered due to changes in the microstructure, specifically the Zr-rich regions and the grain boundary T-phase.     

Microwave-assisted synthesis of lanthanum conversion coating on Mg–Li alloy and its corrosion resistance

Lanthanum-based conversion coating on Mg–Li alloy has been prepared by a microwave-assisted method. X-ray diffractions (XRD) indicate that the intermetallic compounds of lanthanum are formed on Mg–Li alloy surface. Scanning electron microscopy (SEM) images show that the coating has different morphologies and special structures. The corrosion resistance was assessed by means of potentiodynamic polarization curves and electrochemical impedance spectra (EIS). The results indicate that this coating significantly reduces the corrosion rate of Mg–Li alloy in NaCl solution. A comparing experiment indicates that the coating prepared by microwave-assisted process has superior corrosion resistance to the coating obtained at room temperature.     

The negative difference effect of magnesium and of the AZ91 alloy in chloride and stannate-containing solutions

The negative difference effect of pure magnesium and of the alloy AZ91 was investigated by volumetric tests in NaCl with and without addition of Na₂SnO₃. Hydrogen comes from two sources: H₂ which accompanies localized magnesium dissolution inside the pits and H₂ from H₂O reduction at the passive surface outside the pits. By separating the two parts it could be shown that the rate of hydrogen evolution inside the pits is quantitatively consistent with a two-step EC-mechanism of magnesium dissolution with hydrogen evolution coupled to the second dissolution step. Addition of Na₂SnO₃ does not influence the second step.     

Corrosion stress relaxation and tensile strength effects in an extruded AZ31 magnesium alloy

The corrosion effects on the tensile and stress relaxation behavior of an extruded AZ31 magnesium alloy subjected to immersion and salt-spray environments have been investigated. Specimens were simultaneously corroded and stress relaxed in a 3.5 wt.% NaCl solution and then put under a tensile test to failure to determine the stress–strain response over a 60 h test matrix. The AZ31 magnesium alloy shows an evident relaxation in 3.5 wt.% NaCl at room temperature. According to optical and scanning electron microscopy investigations, the fracture surfaces for the immersion environment show a high sensitivity to stress corrosion cracking.     

Corrosion behaviour of die-cast AZ91D magnesium alloy in aqueous sulphate solutions

The corrosion behaviour of die-cast AZ91D magnesium alloys in sulphate solutions was investigated by SEM, FTIR and polarization measurements. For immersion times less than 48 h, no pitting corrosion occurred and only generalized corrosion was apparent. According to the polarization curves, the corrosion rate order of the die-cast AZ91D Mg alloy in three aqueous solutions was: NaCl > MgSO₄ > Na₂SO₄. The main corrosion products were Mg(OH)₂ and MgAl₂(SO₄)₄·22H₂O in the sulphate solutions and the product film was compact. Precipitation of MgAl₂(SO₄)₄·22H₂O required a threshold immersion time.     

Microstructure and corrosion performance of a cold sprayed aluminium coating on AZ91D magnesium alloy

A pure Al coating was deposited on AZ91D magnesium alloy through cold spray (CS) technique. The microstructure of the coating was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that the grain interfaces and subgrains formed close to the particle/particle boundaries. Electrochemical tests revealed that the cold sprayed pure Al coating had better pitting corrosion resistance than bulk pure Al with similar purity in neutral 3.5 wt.% NaCl solution. In addition, a mass-transfer step was found to be involved in the corrosion during 10 days immersion.     

Improvement of corrosion resistance of AZ91D magnesium alloy by holmium addition

The corrosion behaviour of two Mg–9Al–Ho alloys (Mg–9Al–0.24Ho and Mg–9Al–0.44Ho) was evaluated by general corrosion measurements and electrochemical methods in 3.5% NaCl solution saturated with Mg(OH)₂. The experimental results were compared with that of Mg–9Al alloy without Ho addition. Various corrosion rate tests showed that the addition of Ho obviously enhanced corrosion resistance of Mg–9Al alloy. The microstructure of the three magnesium alloys and the morphology of their corrosion product film were examined by Electron Probe Microanalysis (EPMA) and Energy Dispersion Spectroscopy (EDS). The alloys with Ho addition showed a microstructure characterized by α phase solid solution, which was surrounded by some β phase and grain-like Ho-containing phase. The improvement of corrosion resistance of the Mg–9Al–Ho alloys could be explained by the fact that the deposited Ho-containing phases were less cathodic. Moreover, the corrosion product films on the Ho-containing alloy surface demonstrated their ability to restrain further corrosion.     

Corrosion behaviour of sintered NdFeB deposited with an aluminium coating

A protective, pure Al coating was deposited by direct current (DC) magnetron sputtering onto sintered NdFeB magnets. Separated, single phases of sintered NdFeB (the Nd-rich phase, the B-rich phase and the matrix phase) were prepared by arc melting for open circuit potential (OCP) tests. The corrosion process of the sintered NdFeB magnets coated with Al (Al/NdFeB) was studied experimentally. It was found that the corrosion process can be divided into three different stages. The Al coating cannot provide complete sacrificial protection for the sintered NdFeB magnets.     

Corrosion characterization of Mg-8Li alloy in NaCl solution

The corrosion mechanism of Mg-8Li alloy in NaCl solution was investigated by electrochemical testing and SEM observation. The electrochemical results indicated that the corrosion resistance of Mg-8Li alloy in 0.1 M NaCl solution gradually deteriorated with increasing of immersion time expect for 2 h immersion, which was consistent with the SEM observation of corrosion morphology. Mg-8Li alloy exhibited filiform type of attack under significant anodic control of magnesium solution reaction. The cathodic reaction was driven by hydrogen evolution reaction. The presence of filiform corrosion also proved a resistant oxide film naturally formed on the surface of Mg-8Li alloy.     

Controlling the ignition and flammability of magnesium for aerospace applications

The perceived easy ignition and flammability of magnesium alloys create a detrimental safety feature that overshadows their high strength-to-weight ratio and hinders the aerospace application opportunities. To overcome the existing barriers a progress in understanding and controlling the reactivity of magnesium at high temperatures is required. This report describes fundamentals of magnesium ignition and flammability along with laboratory testing procedures and correlations with full scale fire scenarios, related in particular to the aircraft cabin. The influence of alloying elements on high temperature reactivity of magnesium and global efforts to develop ignition resistant and non-flammable magnesium alloys are reviewed. Although ignition and flammability represent quite different quantities, both are controlled by an oxidation resistance of the alloy and its capability to form a dense and protective surface oxide after exposures to an open flame or other heat source. Since surface oxide, composed of pure MgO, does not offer a sufficient protection, the research strategy is focused on modification of its chemistry and microstructure by micro-alloying the substrate with rare earths and other elements having high affinity to oxygen.     

Electrochemical noise analysis on the pit corrosion susceptibility of Mg–10Gd–2Y–0.5Zr, AZ91D alloy and pure magnesium using stochastic model

Pit corrosion susceptibilities of Mg–10Gd–2Y–0.5Zr alloy, AZ91D alloy and pure magnesium were investigated by means of electrochemical noise (EN). The EN data have been analyzed based upon the combined stochastic theory and shot-noise theory. Pit initiation process has been modeled as a nonhomogeneous Poisson process and analyzed using a Weibull distribution function. Pit growth process has been simulated by a nonhomogeneous Markov process and analyzed using Gumbel distribution function. The EN results implied that Mg–10Gd–2Y–0.5Zr alloy had the highest pit initiation rate and pit growth probability, which revealed that Mg–10Gd–2Y–0.5Zr alloy had the highest pit susceptibility.     

Relationship between microstructure and corrosion performance of AA2050-T8 aluminium alloy after excimer laser surface melting

Surface modification by excimer laser surface melting (LSM) has been performed with the aim to improve the corrosion resistance of the AA2050-T8 alloy. LSM produced melted surfaces, largely free of precipitates, with both microstructure and corrosion behaviour depending upon the number of laser pulses employed. Increased number of laser pulses resulted in thicker melted layers, but also in greater trapped porosity and formation of micro-cracks at the overlapping area. Nevertheless, the LSM-treated specimens exhibited enhanced corrosion resistance compared to the untreated alloy, which was associated with the formation of a relatively uniform melted layer and a diminished presence of precipitates.     

Corrosion of hot extrusion AZ91 magnesium alloy. Part II: Effect of rare earth element neodymium (Nd) on the corrosion behavior of extruded alloy

The corrosion behavior of extruded Nd-free AZ91 and extruded AZ91 + 1.5Nd alloy was investigated by weight loss and electrochemical measurements. The results showed that the extruded AZ91 + 1.5Nd alloy had higher corrosion resistance compared to the extruded Nd-free AZ91 alloy, which could been explained from point of view of microstructure changes: (1) the significant decrease of twins and dislocation decreased the anodic dissolution rate; (2) the micro-galvanic corrosion was inhibited by the formation of Al₃Nd phase; and (3) Nd not only increased the percent of Non-Faraday process, but also led to anisotropic feature on the corrosion mechanism.     

Corrosion behaviour of a magnesium matrix composite with a silicate plasma electrolytic oxidation coating

The corrosion behaviour of AZ92 magnesium alloy reinforced with various volume fractions of silicon carbide particles (SiCp) and treated by alternating current (AC) plasma electrolytic oxidation (PEO) was investigated in humid and saline environments. For untreated composites, corrosion attack started around the Al-Mn inclusions and gradually developed into general corrosion without significant galvanic coupling between the matrix and the SiCp. PEO coatings consisted mainly of MgO and Mg₂SiO₄, and revealed increased hardness, reduced thickness and slightly higher corrosion resistance with increasing proportion of reinforcement. Pit formation and hydration of the outer layer were the main mechanisms of corrosion of PEO-treated specimens.     

Corrosion behaviour of bulk ultra-fine grained AZ91D magnesium alloy fabricated by equal-channel angular pressing

Effect of microstructure change on corrosion behaviour of equal-channel angular pressed (ECAPed) AZ91D Mg alloy was investigated. The ECAPed alloy with ultra-fine grained (UFG) α-phase matrix and refined β-phase particles displays a significantly lower corrosion resistance, resulting in more pits after in-situ corrosion, higher mass-loss rate immersed in NaCl solution, larger I_corr values in polarization curves and lower fitted R_t values in EIS plots. Two factors weaken the corrosion resistance: the first is the strains-induced crystalline defects providing the α-phase matrix more corrosion activation, the second is the refined β-phase particles losing barrier to the corrosion propagation in α-phase matrix.     

Corrosion, passivation and breakdown of passivity of neodymium

The anodic polarisation behaviour of neodymium was investigated in various solutions (pH 1-12). While in sulphuric acid solution high dissolution rates were observed, spontaneous passivity occurred in phosphoric acid solutions, oxalic acid solutions and sodium hydroxide solutions. However, the stability of these protecting layers strongly depends on the kind and concentration of anions present, especially in acidic environments. A mechanism of the passive layer breakdown is proposed. During pitting corrosion erosive degradation of the electrode was observed. In all solutions, abnormal hydrogen evolution was observed when neodymium was in the active state during anodic polarisation.     

Corrosion behaviour of sensitized and unsensitized Alloy 900 (UNS 1.4462) in concentrated aqueous lithium bromide solutions at different temperatures

Duplex stainless steels can undergo microstructural changes if they are heated improperly. When that happens, duplex stainless steels are sensitized and intermetallic phases appear. The high Chromium and Molybdenum content promotes the formation of secondary phases as a consequence of the heat treatment. These secondary phases, which are rich in alloying elements, such as Cr and Mo, deplete these elements from the neighbouring phases, leading to a reduction in corrosion resistance. In order to study the influence of the secondary phases on the corrosion parameters, samples of duplex stainless steel, Alloy 900 (UNS 1.4462), have been heated in argon atmosphere at 825 °C for 1 h. The corrosion behaviour of sensitized and unsensitized Alloy 900 has been analyzed in a concentrated aqueous lithium bromide (LiBr) solution of 992 g/L by means of cyclic potentiodynamic curves. Secondary phase presence reduces the pitting potential value of Alloy 900. Besides, the pitting potential decreases with temperature. On the other hand, the corrosion potential and open circuit potential values increase with temperature and sensitization.