Corrosion and corrosion control of mild steel in concentrated H2SO4 solutions by a newly synthesized glycine derivative

A newly synthesized glycine derivative (GlyD1), 2-(4-(dimethylamino)benzylamino)acetic acid hydrochloride, was used to control mild steel corrosion in 4.0 M H₂SO₄ solutions at different temperatures (278–338 K). Tafel extrapolation, linear polarization resistance (LPR) and impedance methods were used to test corrosion inhibitor efficiency. An independent method of chemical analysis, namely ICP-AES (inductively coupled plasma atomic emission spectrometry) was also used to test validity of corrosion rate measured by Tafel extrapolation method. Results obtained were compared with an available glycine derivative (GlyD2) and glycine (Gly). Tafel polarization measurements revealed that the three tested inhibitors function as mixed-type compounds. The inhibition efficiency increased with increase in inhibitor concentration and decreased with temperature, suggesting the occurrence of physical adsorption. The adsorptive behaviour of the three inhibitors followed Temkin-type isotherm and the standard free energy changes of adsorption () were evaluated for the three tested inhibitors as a function of temperature. The inhibition performance of GlyD1 was much better than those of GlyD2 and Gly itself. Results obtained from the different corrosion evaluation techniques were in good agreement.     

Experimental and theoretical calculations on corrosion inhibition of steel in 1 M H2SO4 by crown type polyethers

The corrosion inhibitive efficiencies of two crown type polyethers, namely dibenzo-bis-imino crown ether (C-1) and dibenzo-diaza crown ether (C-2), which are macrocyclic Schiff base and its reduced form (macrocyclic amine), respectively, for the steel in 1 M H₂SO₄ have been investigated by Tafel extrapolation and linear polarization methods. Corrosion and adsorption isotherm parameters were determined from current-potential curves. The studies show that C-1 and C-2 inhibit the corrosion of the steel in H₂SO₄ solution. Semiempirical AM1 method was used for theoretical calculations. The obtained results of these calculations for the compounds were found to be consistent with the experimental findings.     

Corrosion monitoring of mild steel in sulphuric acid solutions in presence of some thiazole derivatives – Molecular dynamics, chemical and electrochemical studies

The physical behavior of three selected thiazole derivatives, namely 2-Amino-4-(p-tolyl)thiazole (APT), 2-Methoxy-1,3-thiazole (MTT) and Thiazole-4-carboxaldehyde (TCA) at iron (1 1 0) surface dissolved in aqueous solution were studied via molecular dynamics (MD) simulations. From the calculated binding energies, APT showed preferred adsorption on the steel surface among the three tested thiazole derivatives. The inhibition performance of the three thiazoles on the corrosion of mild steel in 0.5 M H₂SO₄ solutions was investigated at 25 °C. Measurements were conducted under various experimental conditions using weight loss, Tafel polarization and electrochemical impedance spectroscopy. Electrochemical frequency modulation (EFM) technique was also employed here to make accurate determination of the corrosion rates and test validation of the Tafel extrapolation method for measuring corrosion rates. Polarization curves showed that the three thiazole derivatives were of mixed-type inhibitors for mild steel corrosion in 0.5 M H₂SO₄ solution. EFM results were in agreement with other traditional chemical and electrochemical techniques used in corrosion rate measurements. Chemical and electrochemical measurements are consistent with computational study that APT is the most effective inhibitor among the tested thiazoles.     

Electrochemical frequency modulation and inductively coupled plasma atomic emission spectroscopy methods for monitoring corrosion rates and inhibition of low alloy steel corrosion in HCl solutions and a test for validity of the Tafel extrapolation method

The inhibition effect of glycine (Gly) towards the corrosion of low alloy steel ASTM A213 grade T22 boiler steel was studied in aerated stagnant 0.50 M HCl solutions in the temperature range 20-60 °C using potentiodynamic polarization (Tafel polarization and linear polarization) and impedance techniques, complemented with scanning electron microscope (SEM) and energy dispersive X-ray (EDX). Electrochemical frequency modulation (EFM), a non-destructive corrosion measurement technique that can directly give values of corrosion current without prior knowledge of Tafel constants, is also presented here. Experimental corrosion rates determined by the Tafel extrapolation method are compared with corrosion rates obtained by electrochemical, namely EFM technique, and chemical (i.e., non-electrochemical) method for steel in HCl. The chemical method of confirmation of the corrosion rates involved determination of the dissolved cation, using ICP-AES (inductively coupled plasma atomic emission spectrometry) method of analysis. Corrosion rates (in mm y⁻¹) obtained from the electrochemical (Tafel extrapolation and EFM) and the chemical method, ICP, are in a good agreement. Polarization studies have shown that Gly is a good “green”, mixed-type inhibitor with cathodic predominance. The inhibition process was attributed to the formation of an adsorbed film on the metal surface that protects the metal against corrosive agents. Scanning electron microscopy (SEM) and energy dispersion X-ray (EDX) examinations of the electrode surface confirmed the existence of such an adsorbed film. The inhibition efficiency increases with increase in Gly concentration, while it decreases with solution temperature. Temkin isotherm is successfully applied to describe the adsorption process. Thermodynamic functions for the adsorption process were determined.     

A study of the inhibition of iron corrosion in HCl solutions by some amino acids

The performance of three selected amino acids, namely alanine (Ala), cysteine (Cys) and S-methyl cysteine (S-MCys) as safe corrosion inhibitors for iron in aerated stagnant 1.0 M HCl solutions was evaluated by Tafel polarization and impedance measurements. Results indicate that Ala acts mainly as a cathodic inhibitor, while Cys and S-MCys function as mixed-type inhibitors. Cys, which contains a mercapto group in its molecular structure, was the most effective among the inhibitors tested, while Ala was less effective than S-MCys. The low inhibition efficiency recorded for S-MCys compared with that of Cys was attributed to steric effects caused by the substituent methyl on the mercapto group. Electrochemical frequency modulation (EFM) technique and inductively coupled plasma atomic emission spectrometry (ICP-AES), were also applied to make accurate determination of corrosion rates. Validation of the Tafel extrapolation method for measuring corrosion rates was tested. Rates of corrosion rates (in μm y⁻¹) obtained from Tafel extrapolation method are in good agreement with those measured using EFM and ICP methods. Some theoretical studies, including molecular dynamics (MD) and density functional theory (DFT), were also employed to establish the correlation between the structure (molecular and electronic) of the three tested inhibitors and the inhibition efficiency. Adsorption via hydrogen bonding was discussed here based on some theoretical studies. Experimental and theoretical results were in good agreement.     

Corrosion behavior of alumina ceramics in aqueous HCl and H2SO4 solutions

The corrosion behavior of cold isostatically pressed (CIP) high purity alumina ceramics in aqueous HCl and H₂SO₄ solutions with various concentrations has been studied simultaneously at room temperature (25 °C). Corrosion tests were also performed with 0.65 mol/l HCl and 0.37 mol/l H₂SO₄ solutions at 40, 55 and 70 °C for 48 h. Chemical stability was monitored by determining the amount of Al³⁺, Mg²⁺, Ca²⁺, Na⁺ Si⁴⁺ and Fe³⁺ ions eluted in different concentrations of HCl and H₂SO₄ solutions by means of atomic absorption spectrometry (AAS). By increasing the concentration from 0.37 to 6.5 mol/l, it was notified that the corrosion susceptibility in HCl and H₂SO₄ solutions for the CIP alumina specimens at room temperature decreases.     

Corrosion of niobium in sulphuric and hydrochloric acid solutions at 75 and 95 °C

New Pourbaix diagrams were calculated at 25, 75 and 95 °C for the Nb-H₂O system. The species and were considered. Potentiodynamic polarization and mass loss experiments (14 days) were conducted in concentrated H₂SO₄ (20, 40 and 80 wt%) and HCl (20 and 38 wt%) solutions at 75 and 95 °C. Nb forms a metastable pentoxide (Nb₂O₅) in H₂SO₄ and HCl solutions which dissolves as . Corrosion rates decrease between the 40% and the 80% H₂SO₄ solutions. SEM micrographs show generalized pitting in the 20% and 40% H₂SO₄ solutions. Mass loss corrosion rates did not exceed 306 μm/yr. Corrosion rates estimated by Tafel extrapolation were within two orders of magnitude of those measured by mass loss and it is shown that this finding is consistent with the thickening of the oxide.     

Inhibition effect of 6-benzylaminopurine on the corrosion of cold rolled steel in H2SO4 solution

The inhibition effect of 6-benzylaminopurine (BAP) on the corrosion of cold rolled steel (CRS) in 1.0-7.0 M H₂SO₄ at 25-50 °C was studied by weight loss and potentiodynamic polarization methods. Fourier transform infrared spectroscopy (FTIR) and atomic force microscope (AFM) were used to characterize the CRS surface. The results showed that BAP was a good inhibitor in 1.0 M H₂SO₄, and the adsorption of BAP obeyed the Temkin adsorption isotherm. Polarization curves showed that BAP acted as a mixed-type inhibitor in sulfuric acid. Depending on the results, the inhibitive mechanism was proposed.     

Effects of dithionite ion on corrosion of type 304 stainless steel in sulphuric acid solution

Corrosion behaviour of type 304 stainless steel was investigated, with particular attention to additive effects of hydrosulphite (Na₂S₂O₄) on corrosion in 0.1 mol/l H₂SO₄ solution with various amounts of Na₂S₂O₄ up to 60 mmol/l.Corrosion of SUS304 occurred below pH 3.0 at 30 °C in a 0.1 mol/l H₂SO₄ solution in which Na₂S₂O₄ was added to 0.1-20 mmol/l. The maximum corrosion rate at 30 °C was measured as 7.2 g/m² h (7.9 mm/y) in 0.1 mol/l H₂SO₄-10 mmol/l Na₂S₂O₄ at pH 1.2. Microscopic surface observation revealed that active dissolution was accompanied by intergranular corrosion at the metal surface.The SUS304 was easily passivated in 0.1 mol/l H₂SO₄ solution with more than 30 mmol/l Na₂S₂O₄. NiS was detected in the passivated film.     

Numerical simulation of corrosion process with two-step charge transfer mechanism in the Cu/CuSO4 + H2SO4 system

The corrosion process in the Cu/CuSO₄ + H₂SO₄ system is considered as the sum of two coupled single-electron electrochemical reactions that occur simultaneously and independently on the surface of the copper electrode. Our numerical model incorporates diffusion and migration of solution species including cuprous ions, as well as the chemical equilibria for copper sulphate and sulphuric acid dissociation. Numerical simulations are compared with the trends discovered during experimental investigation of copper corrosion in similar systems.     

Synergistic effect of iodide ion and polyacrylic acid on corrosion inhibition of iron in H2SO4 investigated by electrochemical techniques

Corrosion inhibition of iron in H₂SO₄ by polyacrylic acid (PAA) was investigated using electrochemical techniques at 30 °C. Results obtained indicate that PAA inhibited the corrosion of iron in the acid medium. Inhibition efficiency increases with increase in PAA concentration and synergistically enhanced on addition of iodide ions. Potentiodynamic polarization results suggest that PAA functions as a modest cathodic inhibitor. The adsorption of PAA onto the iron surface followed Temkin adsorption isotherm. FTIR analysis revealed that the synergistic effect due to co-adsorption of iodide ions and PAA is co-operative in nature.     

Al2O3-ZrO2 mixed oxide composite incorporated aluminium rich zinc coatings for high wear resistance

Corrosion resistance and wear resistance are the two important parameters for high performance of zinc galvanic coating. In the present work, the improvement of these two characteristics was achieved by the incorporation of Al₂O₃-ZrO₂ mixed oxide composite in the coating. Al₂O₃-ZrO₂ mixed oxide composite was synthesized from ZrOCl₂·8H₂O. Aluminium rich zinc coatings with high sliding wear resistance was developed from a galvanic bath containing the mixed oxide. Based on the performance of the coating during physicochemical and electrochemical characterization, the concentration of mixed oxide composite in the bath was optimized as 0.50 wt% Al₂O₃-0.50 wt% ZrO₂. While rich in Al-metal content in the coating caused high corrosion resistance, the incorporation of the mixed oxide improved structural characteristics of the coating resulting in high wear resistance also. The coating was nonporous in nature and even the interior layers had high stability. The coatings have potential scope for high industrial utility.     

Synergism between red tetrazolium and uracil on the corrosion of cold rolled steel in H2SO4 solution

The synergism between red tetrazolium (RT) and uracil (Ur) on the corrosion of cold rolled steel (CRS) in H₂SO₄ solution is first investigated by weight loss, potentiodynamic polarization, and atomic force microscope (AFM). Effects of inhibitor concentration (25-500 mg l⁻¹), temperature (20-50 °C), and acid concentration (1.0-5.0 M) on synergism are discussed systematically. The results reveal that RT has a moderate inhibitive effect, and its adsorption obeys the Freundlich adsorption isotherm. For Ur, it has a poor effect. However, incorporation of RT with Ur significantly improves the inhibition performance, and produces synergistic inhibition effect.     

Synergistic effect of halide ions on improving corrosion inhibition behaviour of benzisothiozole-3-piperizine hydrochloride on mild steel in 0.5 M H2SO4 medium

The synergistic effect of iodide ions and benzisothiozole-3-piperizine hydrochloride (BITP) on corrosion inhibition of mild steel in 0.5 M H₂SO₄ solution has been studied by both chemical and electrochemical methods. The corrosion performance of BITP in 1.0 M HCl and 0.5 M H₂SO₄ media was examined and compared. The adsorption of BITP and its combination with iodide ions on mild steel surface followed Langmuir adsorption isotherm via chemisorption mechanism. The calculated values of synergism parameter (S_θ) were found to be greater than unity. This result clearly showed the existence of synergism between iodide ions and BITP molecules.     

Inhibitory effect of some amino acids on corrosion of Pb-Ca-Sn alloy in sulfuric acid solution

The present article describes the inhibition effect of amino acids cysteine (Cys), methionine (Met) and alanine (Ala), towards the corrosion of lead-alloy (Pb-Ca-Sn) in H₂SO₄ solution by potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), weight loss measurement and scanning electron microscopy (SEM) methods. The influence of inhibitor concentration, temperature and time on inhibitory behavior of the amino acids was investigated. The corrosion data including corrosion current density (I_corr), corrosion potential (E_corr) and charge transfer resistance (R_ct) were determined from Tafel plots and EIS. Recording impedance spectra showed that the charge transfer resistance is increased by increasing adsorption time. The SEM micrographs revealed that the corroded surface area is decreased in the presence of amino acids. Meanwhile, the inhibition efficiency (IE) was found to be depending on the type of amino acid and its concentration. The IE for 0.1 M Cys in 0.5 M H₂SO₄ is greater than 96%. Adsorption isotherms were fitted by Langmuir isotherm.     

Corrosion study of HK-40m alloy exposed to molten sulfate/vanadate mixtures using the electrochemical noise technique

Corrosion performance of HK-40m alloy obtained from electrochemical noise technique and polarization curves during 24 h of exposure in high sulfate (80 mol% Na₂SO₄-20 mol% V₂O₅) and high vanadate (80 mol% V₂O₅-20 mol% Na₂SO₄) molten salts at 700 °C are reported. Electrochemical noise signals were analyzed in the time and frequency domain. A statistical analysis obtaining the resistance noise, the current standard deviation and the localization index are presented as well as the determination of corrosion rates. Corrosion rates were supported by X-ray diffraction analysis of corrosion products and scanning electron microscopy analysis of corroded samples. Results from optical microscope examination of the corroded samples showed that HK-40m alloy suffered inter-granular corrosion when was exposed to the high vanadate salt, whereas exposed to the high sulfate salt, HK-40m corroded through a mixed corrosion process. A corrosion mechanism of HK-40m alloy was obtained together with the corrosion rate, showing the different behavior when exposing the alloy to a high vanadate and high sulfate molten salts.     

Testing validity of the Tafel extrapolation method for monitoring corrosion of cold rolled steel in HCl solutions - Experimental and theoretical studies

The protection influence of glycine (Gly) and a one of its derivatives, namely 2-(bis(2-aminoethyl)amino) acetic acid, designated here as GlyD; where GlyD stands for “glycine derivative”, against cold rolled steel (CRS) corrosion was studied in aerated stagnant 1.0 M HCl solutions at 25 °C. Measurements were conducted under various experimental conditions using Tafel polarization, linear polarization and impedance techniques. These studies have shown that Gly and GlyD are very good “green”, mixed-type inhibitors. GlyD is more effective than Gly itself in inhibiting the acid corrosion of CRS. Electrochemical frequency modulation (EFM) and inductively coupled plasma-atomic emission spectroscopy (ICP-AES) method of analysis are also presented here for monitoring corrosion. Corrosion rates obtained from both EFM and ICP-AES methods are comparable with those recorded using Tafel extrapolation method, confirming validation of corrosion rates measured by the latter. Adsorption via H-bond is discussed here, based on the presence of oxide film on the electrode surface as well as the number of NH linkages in the inhibitor molecule. Quantum chemical method was also employed to explore the relationship between the inhibitor molecular properties and its protection efficiency. The density function theory (DFT) is used to study the structural properties of Gly and GlyD in aqueous phase in an attempt to understand their inhibition mechanism. The protection efficiencies of these compounds showed a certain relationship to highest occupied molecular orbital (HOMO) energy, Mulliken atomic charges and Fukui indices.     

High temperature corrosion properties of ionic liquids

The corrosion behaviour of several metals and metal alloys (copper, nickel, AISI 1018 steel, brass, Inconel 600) exposed to a typical ionic liquid, the 1-butyl-3-methyl-imidazolium bis-(trifluoromethanesulfonyl) imide, ([C₄mim][Tf₂N]), has been investigated by electrochemical and weight-loss methods. Corrosion current densities have been determined by extrapolation from Tafel plots and by polarization resistance measurements and 48 h immersion tests were performed at 150, 250, 275 and 325 °C. Room temperature results show low corrosion current densities (0.1-1.2 μA/cm²) for all the metals and alloys investigated. At 70 °C, the corrosion current for copper dramatically increases showing a strongly dependence on temperature. At 150 °C copper shows significant weight-loss while nickel, AISI 1018, brass and Inconel do not. At higher temperatures (?275 °C), the copper sample crumbles and localized corrosion occurs for the other metals and alloys.     

Poly(N-methylaniline) coatings on stainless steel by electropolymerization

Poly(N-methylaniline) (PNMA) coatings have been electropolymerized on 304 stainless steel alloy by potentiodynamic, galvanostatic and potentiostatic synthesis techniques from aqueous solutions of 0.1 M N-methylaniline (NMA) and 0.3 M oxalic acid. Characterization of PNMA coatings was carried out by cyclic voltammetry, UV-Vis and FTIR spectroscopy techniques. Corrosion behavior of PNMA coated stainless steel electrodes was investigated using linear anodic potentiodynamic polarization, Tafel test, chronoamperometry and electrochemical impedance spectroscopy (EIS) techniques in 0.5 M aqueous HCl solutions. Corrosion test results showed that PNMA coatings possessed protection to uncoated stainless steel against corrosion.     

Discontinuous oxidation and erosion-oxidation of a CeO2-dispersion-strengthened chromium coating

A CeO₂-dispersion-strengthened chromium coating was developed on a carbon steel using a two-step process: prior electrodeposition of a Ni-CeO₂ nanocomposite film and subsequent chromization using a conventional pack cementation method. Compared to the CeO₂-free coatings prepared on the carbon steel without and with pre-electrodeposition of a pure Ni film, the CeO₂ dispersed chromium coating offered profoundly improved discontinuous oxidation resistance at 900 °C in 5% O₂ + N₂ and in 5% O₂ + 1000 ppm SO₂ + N₂, and erosion-oxidation resistance in a laboratory-scale fluidized-bed combustor (FBC), mainly because of the development of a denser, less wrinkled and more adherent chromia scale.