Effect of rapid solidification on the microstructure and corrosion behaviour of Al-Zn-Mg based material

The corrosion behaviour of Al-5Zn-3Mg-0.6Cu-0.8Zr-0.25Cr-0.15Ni-0.15Ti alloys, produced by traditional and powder technologies, with similar thermo-mechanical treatments, in 3% sodium chloride solution, has been examined by electrochemical methods, scanning electron microscopy, transmission electron microscopy and X-ray microanalysis. The alloys reveal similar precipitation but of different shape, size and distribution; further, both alloys experience localized corrosion. Copper-rich precipitates initiate the dissolution of surrounding particles, enriched in Zn and Mg. As a result, the surface is enriched with other alloying elements after a full polarisation run. Cast material has lower corrosion properties because of the higher heterogeneity of the structure. The structure heterogeneity of the cast material involves a more non-uniform distribution of the precipitates, larger Zn- and Mg-rich particles, and depletion of the matrix and areas around the precipitates by alloying elements compared with the powder material.     

Effect of plasma electrolytic oxidation coating on the stress corrosion cracking behaviour of wrought AZ61 magnesium alloy

An attempt was made to understand the effect of silicate based plasma electrolytic oxidation (PEO) coating on the stress corrosion cracking (SCC) behaviour of an AZ61 wrought magnesium alloy. The SCC behaviour of untreated and PEO coated specimens was assessed using slow strain rate tensile tests at two different nominal strain rates, viz. 1 × 10⁻⁶ s⁻¹ and 1 × 10⁻⁷ s⁻¹, in ASTM D1384 test solution at ambient conditions. The PEO coating was found to improve the general corrosion resistance to a significant extent; however, the improvement in the resistance to stress corrosion cracking was only marginal.     

The effect of molybdenum on the corrosion behaviour of the high-entropy alloys Co1.5CrFeNi1.5Ti0.5Mox in aqueous environments

The purpose of this study is to investigate the electrochemical properties of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x high-entropy alloys in three aqueous environments which simulate acidic, marine, and basic environments at ambient temperature (∼25 °C). The potentiodynamic polarisation curves of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x alloys, obtained in aqueous solutions of H₂SO₄ and NaOH, clearly revealed that the corrosion resistance of the Mo-free alloy was superior to that of the Mo-containing alloys. On the other hand, the lack of hysteresis in cyclic polarisation tests and SEM micrographs confirmed that the Mo-containing alloys are not susceptible to pitting corrosion in NaCl solution.     

Effect of grain size and twins on corrosion behaviour of AZ31B magnesium alloy

Grain refining is a promising approach to improve mechanical properties of magnesium alloys, but how grain size and twins affect corrosion behaviour is not well understood. In this work, corrosion resistance of AZ31B alloy with different grain sizes is studied in 3.5% NaCl solution using immersion testing, evolved hydrogen gas measurement and potentiodynamic polarisation measurement. Intra-granular corrosion was predominant and the existence of twins further accelerated the corrosion. The effect of grain size was more pronounced in the corrosion of the untwinned microstructure. The corrosion rate significantly increased as the average grain size increased from 65 to 250 μm.     

Effect of heat treatment on corrosion behaviour of magnesium alloy AZ91D in simulated body fluid

The research explored ways of improving corrosion behaviour of AZ91D magnesium alloy through heat treatment for degradable biocompatible implant application. Corrosion resistance of heat-treated samples is studied in simulated body fluid at 37 °C using immersion and electrochemical testing. Heat treatment significantly affected microgalvanic corrosion behaviour between cathodic β-Mg₁₇Al₁₂ phase and anodic α-Mg matrix. In T4 microstructure, dissolution of the β-Mg₁₇Al₁₂ phase decreased the cathode-to-anode area ratio, leading to accelerated corrosion of α-Mg matrix. Fine β-Mg₁₇Al₁₂ precipitates in T6 microstructure facilitated intergranular corrosion and pitting, but the rate of corrosion was less than those of as-cast and T4 microstructures.     

The effect of impurity inclusions on the pitting corrosion behaviour of beryllium

An electrochemical polarisation study has been conducted to determine the effect of impurity inclusions on the pitting corrosion behaviour of beryllium. Three grades of commercial beryllium differing in impurity levels were used. This work showed a strong relationship between the pitting potential of the beryllium and the level of impurity inclusions, the grade with the least number of overall inclusions being the most resistant to pitting corrosion. The work also revealed the preferred sites for pit initiation, with most corrosion pits initiating at intermetallic Fe/Al/Be inclusions, and to a smaller extent at inclusion sites containing either elemental silicon or carbides.     

Heat-transfer corrosion behaviour of cast Al alloy

Heat-transfer corrosion behaviour of an ISO 2379 cast Al alloy was studied in antifreeze radiator coolant under heat-rejecting condition. Extensive analyses of microstructures and corroded surfaces were carried out under the optical microscope, scanning electron microscope equipped with energy dispersive spectroscopy and X-ray diffractometer. Heat-rejecting condition led to a cavitation process and cavities were observed within the α-Al matrix. Crevice corrosion was predominant at oxygen depleted regions in heat-transfer corrosion cell. Al₂Cu, Al₁₅(Fe,Mn)₃Si₂ dendrites, Al₄Cu₂Mg₈Si₇ and Si phases served as the effective cathodes resulting microgalvanic corrosion at the anodic site of α-Al matrix.     

Effect of antimony, bismuth and calcium addition on corrosion and electrochemical behaviour of AZ91 magnesium alloy

This study investigated the effect of antimony, bismuth and calcium addition on the corrosion and electrochemical behaviour of AZ91 magnesium alloy in 3.5% NaCl solution. Techniques including constant immersion, electrochemical potentiodynamic polarisation, scanning electron microscopy (SEM), energy dispersed spectroscopy (EDS) and X-ray diffraction (XRD) were used to characterise electrochemical and corrosion properties and surface topography. It was found that corrosion attack occurred preferentially on Mg₃Bi₂ and Mg₃Sb₂ particles while Mg₁₇Al₈Ca_0.5 and Mg₂Ca phases showed no detrimental effect on corrosion. Combined addition of small amounts of bismuth and antimony to the AZ91 alloy resulted in significant increase in corrosion rate.     

Influence of alloyed Nd content on the corrosion of an Al–5Mg alloy

The influence of neodymium (Nd) additions from 0 to 0.17 wt.% on the electrochemical response, corrosion, and hardness of a model 5xxx alloy (Al–5Mg) was studied. The combination of SEM, polarisation, constant immersion and nitric acid mass loss testing, followed by optical profilometry, revealed that Nd had no significant effect on pitting or general corrosion of Al–5Mg; however with Nd additions the extent of intergranular corrosion following sensitisation was decreased substantially. Nd additions also increased alloy hardness and thus microalloying with Nd was shown to improve the properties of Al–5Mg.     

Corrosion of heat treated magnesium alloy ZE41

This paper investigates the effect of heat treatment upon the corrosion morphology and mechanism of ZE41 alloy. The results of optical and scanning electron microscopy (SEM) together with potentiodynamic polarisation reveal the importance of the microstructure in the initiation and propagation of corrosion in an aqueous environment. The corrosion of the heat-treated alloy is significantly altered due to changes in the microstructure, specifically the Zr-rich regions and the grain boundary T-phase.     

Effect of alternating voltage treatment on the microstructure and corrosion resistance of stannate conversion coating on AZ91D alloy

A new stannate conversion coating (CC) on AZ91D alloy was synthesized by the application of alternative voltage (AV) treatment technique. By using AV technique, the formation process of CC can be controlled. SEM results indicated that a continuous and compact dual-layer CC was formed on alloy surface after AV treatment. TEM results revealed that the inner layer consists of magnesium–aluminum–stannum nano-crystals and amorphous, meanwhile, the outer layer is primarily a mixture of magnesium–stannum hydroxides and oxides with amorphous structure. The electrochemical experimental results revealed that AV treatment significantly improved the corrosion resistance of CC, which attributed to the distinguishing microstructure of AV-CC.     

Effect of tin modification on corrosion of AM70 magnesium alloy

In this study, AM70 magnesium alloys with and without 2 wt.% Sn addition are compared for their corrosion performance. They are found to have similar corrosion rates in the first 70 h in 5 wt.% NaCl solution, but in extended immersion test the Sn modified AM70 exhibits accelerated overall corrosion. Nevertheless, Sn modification significantly decreases the susceptibility of the alloy to localized corrosion attack. Polarization curve measurements further indicate that the Sn modified AM70 is likely to have worse galvanic corrosion than AM70 in terms of the loss of metal, but again the Sn modification makes the galvanic corrosion less localized, which is an improvement aspect of the galvanic corrosion performance. The effect of Sn addition on the corrosion behavior appears to be associated with the presence of Sn-containing particles and the solute Sn in the matrix phase, which may change the electrochemical anodic and cathodic polarization behavior of the alloy.     

Pitting corrosion of spray formed Al-Li-Mg alloys

The pitting corrosion behaviour of two new spray formed alloys, designated OX24 and OX27, has been compared with spray formed AA7034 and more corrosion resistant AA5083 by polarisation tests. The new alloys have been designed for use in the aerospace industry where good corrosion resistance and specific mechanical properties are required. OX24 and AA5083 had good corrosion resistance; OX27 pitted immediately showing poor corrosion resistance. However, both OX24 and OX27 show better corrosion resistance than AA7034. Scanning electron microscopy showed that corrosion was associated with intermetallic particles, except in OX24 where initiation appeared not to be associated with the Zr-rich intermetallics.     

An investigation on corrosion behaviour of pressure infiltrated Al-Mg alloy/SiCp composites

In this study, effect of Mg alloying addition (2-8 wt.%) on corrosion behaviour of Al matrix composites, in 3.5 wt.% NaCl environment, has been investigated. Composites were produced by pressure infiltration technique at 750 °C and had a SiC particle (SiC_p) volume fraction of ∼60%. Results were evaluated by using potentiodynamic polarisation measurements, immersion tests, SEM, EDS and XRD analysis. Compared to the pure Al matrix, mass loss of the composites decreased with increasing Mg content. Experimental results revealed that intermetallics as a result of reaction between Al-Mg alloy and SiC particle has beneficial effect on corrosion resistance of the composites due to interruption of the continuity of the matrix channels within the pressure infiltrated composites.     

Comparison of the corrosion behaviour of bulk and thin film magnesium alloys

The corrosion behaviour of bulk and thin film specimens consisting of commercial magnesium alloys AZ31 and AZ80 was investigated by electrochemical tests in 3.5 wt.% NaCl solution and in phosphate buffered saline solution (PBS) at room temperature. Corrosion tests indicated that the corrosion rates are nearly equal, but localized attack was more pronounced for the bulk specimens than for the thin film samples. XRD analyses showed that this behaviour can be attributed to the fact that the as-deposited thin film specimens do not contain any precipitates, which are present in the bulk samples and are considered to enhance localized corrosion.     

Effect of carbon nanotubes on corrosion of Mg-CNT composites

Carbon nanotubes (CNTs) may be added to Mg matrix to produce composites of better mechanical properties, but their effect on the corrosion behaviour is not well understood. The corrosion resistance of pure Mg and its composites reinforced with 0.3 and 1.3 wt.% CNTs was studied in 3.5 wt.% NaCl solution using immersion testing and electrochemical measurements. It was found that the corrosion rate was increased considerably by the presence of CNTs because of microgalvanic action between the cathodic CNTs and the anodic Mg matrix.     

Corrosion-resistant ZSM-5 zeolite coatings formed on Mg–Li alloy by hot-pressing

Here we report a novel approach of hot-pressing, adapted to assembly ZSM-5 (Zeolite Socony Mobile-Five) coatings on Mg–Li alloy. X-ray diffraction (XRD) patterns and scanning electron microscopy (SEM) images show that ZSM-5 coatings are uniform and compact. The ZSM-5 exhibits a pure MFI structure. The corrosion behaviors of Mg–Li alloy and ZSM-5 coatings are investigated by electrochemical and immersion tests. The results indicate that ZSM-5 coatings improved the corrosion resistance of Mg–Li alloy, which is related to templates blocking the pores of ZSM-5. The concept of hot-pressing introduced here may be helpful to assemble uniform coatings on other substrates.     

Effect of solution treatment on the corrosion behaviour of aluminium alloy AA7150: Optimisation for corrosion resistance

Studies for Al-alloys normally employ specimens subject to a fixed solution heat treatment (SHT), and hence the specific role of solutionising is overlooked. It is revealed that SHT has a major role in corrosion of AA7150 as judged by electrochemical, microscopic and profilometry studies. SHT dictates the constituent particle type and population remaining in the alloy for subsequent processing, and is thus not only a principal factor in corrosion, but a factor that can be engineered in developing more damage tolerant AA7150. Effect of an optimised SHT minimising the residual MgZn₂ and Al₂MgCu content on corrosion resistance is demonstrated.     

The role of silicon in the corrosion of AA6061 aluminium alloy laser weldments

The galvanic corrosion temporal increase observed on examination of the weld fusion zone (WFZ) of AA6061 laser weldments in 3.5 wt.% NaCl solution cannot be attributed to electron tunnelling as the surface oxide layer is too thick, or the presence of Cl⁻ within the surface layer as this element was not found to be present. Aluminium alloy and WFZ galvanic and surface analyses indicate that the cathodic WFZ corrosion characteristics are due to increases in silicate concentrations in the surface oxide layer, leading to increased ionic and/or p-type semi-conductor conductivity, intermetallic concentrations and surface area.