Hot corrosion behaviour of plasma sprayed YSZ/LaMgAl11O19 composite coatings in molten sulfate–vanadate salt

Hot corrosion studies of thermal barrier coatings (TBCs) with different YSZ/LaMgAl₁₁O₁₉ (LaMA) composite coating top coats were conducted in 50 wt.% Na₂SO₄ + 50 wt.% V₂O₅ molten salt at 950 °C for 60 h. Results indicate that TBCs with composite coating top coats exhibit superior oxidation and hot corrosion resistances to the TBC with the traditional YSZ top coat, especially for which has a LaMA overlay. The presence of LaMA can effectively restrain the destabilization of YSZ at the expense of its own partial degradation. The hot corrosion mechanism of LaMA coating and the composite coatings have been explored.     

Hot corrosion behavior of detonation gun sprayed Cr3C2–NiCr coatings on Ni and Fe-based superalloys in Na2SO4–60% V2O5 environment at 900 °C

The present work investigates the hot corrosion resistance of detonation gun sprayed (D-gun) Cr₃C₂–NiCr coatings on Superni 75, Superni 718 and Superfer 800 H superalloys. The deposited coatings on these superalloy substrates exhibit nearly uniform, adherent and dense microstructure with porosity less than 0.8%. Thermogravimetry technique is used to study the high temperature hot corrosion behavior of bare and Cr₃C₂–NiCr coated superalloys in molten salt environment (Na₂SO₄–60% V₂O₅) at high temperature 900 °C for 100 cycles. The corrosion products of the detonation gun sprayed Cr₃C₂–NiCr coatings on superalloys are analyzed by using XRD, SEM, and FE-SEM/EDAX to reveal their microstructural and compositional features for elucidating the corrosion mechanisms. It is shown that the Cr₃C₂–NiCr coatings on Ni- and Fe-based superalloy substrates are found to be very effective in decreasing the corrosion rate in the given molten salt environment at 900 °C. Particularly, the coating deposited on Superfer 800 H showed a better hot corrosion protection as compared to Superni 75 and Superni 718. The coatings serve as an effective diffusion barrier to preclude the diffusion of oxygen from the environment into the substrate superalloys. It is concluded that the hot corrosion resistance of the D-gun sprayed Cr₃C₂–NiCr coating is due to the formation of desirable microstructural features such as very low porosity, uniform fine grains, and the flat splat structures in the coating.     

Hot corrosion of YSZ/Al2O3 dispersed NiCrAlY plasma-sprayed coatings in Na2SO4-10 wt.% NaCl melt

This study examines the effect of ytrria stabilized zirconia (YSZ) dispersion on hot corrosion behaviour of NiCrAlY bond coat. Hot corrosion studies were conducted on NiCrAlY and NiCrAlY containing 25, 50 and 75 wt.% YSZ coatings obtained through the air plasma spray technique, in Na₂SO₄ + 10 wt.% NaCl environment at 800 °C. The results show that YSZ dispersion lowers the overall hot corrosion tendency of the NiCrAlY, though it enhances the inherent hot corrosion tendency of its metallic constituent (NiCrAlY). Furthermore, there exists a threshold oxide level beyond which it adversely affects the hot corrosion of the coating.     

Evaluation of microstructural evolution of thermal barrier coatings exposed to Na2SO4 using impedance spectroscopy

Impedance spectroscopy as a non-destructive evaluation technique was employed to study the microstructural evolution of thermal barrier coatings exposed to Na₂SO₄ at 950 °C. The results showed that the resistance and capacitance of yttria-stabilized zirconia top coat increased with corrosion time. The resistance of thermally growth oxide (TGO) from 20 to 60 h decreased slowly, which indicates there is little change in the composition of TGO. The fast decrease in the resistance of TGO from 60 to 100 h may correspond to the compositional change of TGO from a-Al₂O₃ to more conductive NiO and Ni(Cr, Al)₂O₄ with corrosion time.     

Hot corrosion of a novel (Ni,Co)O/(Ni,Co)Fe2O4 composite coating thermally converted from an electrodeposited Ni–Co–Fe2O3 composite coating

Ni–Co–Fe₂O₃ composite coatings were successfully developed by sediment co-deposition. In order to improve their hot corrosion resistance, a pre-oxidation treatment was conducted at 1000 °C for 6 h. The corrosion behaviour of the oxidised composite coating was investigated at 960 °C in an atmosphere consisting of a mixture of Na₃AlF₆–AlF₃–CaF molten salts and air. They exhibited good hot corrosion resistance due to not only the pre-formed oxide scale with (Ni,Co)O and (Ni,Co)Fe₂O₄ phases after pre-oxidation, but also the formation of (Ni,Co,Fe)Al₂O₄ phases in the outer layer and a well-distributed NiFe₂O₄-enriched phase along the grain boundaries in the subscale area during the corrosion process.     

Hot corrosion resistance of high-velocity oxyfuel sprayed coatings on a nickel-base superalloy in molten salt environment

No alloy is immune to hot corrosion attack indefinitely. Coatings can extend the lives of substrate materials used at higher temperatures in corrosive environments by forming protective oxides layers that are reasonably effective for long-term applications. This article is concerned with studying the performance of high-velocity oxyfuel (HVOF) sprayed NiCrBSi, Cr₃C₂−NiCr, Ni−20Cr, and Stellite-6 coatings on a nickel-base superalloy at 900 °C in the molten salt (Na₂SO₄-60% V₂O₅) environment under cyclic oxidation conditions. The thermogravimetric technique was used to establish kinetics of corrosion. Optical microscope, x-ray diffraction, scanning electron microscopy/electron dispersive analysis by x-ray (SEM/EDAX), and electron probe microanalysis (EPMA) techniques were used to characterize the as-sprayed coatings and corrosion products. The bare superalloy suffered somewhat accelerated corrosion in the given environmental conditions. whereas hot corrosion resistance of all the coated superalloys was found to be better. Among the coating studied, Ni−20Cr coated superalloy imparted maximum hot corrosion resistance, whereas Stellite-6 coated indicated minimum resistance. The hot corrosion resistance of all the coatings may be attributed to the formation of oxides and spinels of nickel, chromium, or cobalt.     

Hot corrosion of a novel NiO/NiFe2O4 composite coating thermally converted from the electroplated Ni–Fe alloy

A novel NiO/NiFe₂O₄ composite coating thermally converted from an electroplated Ni–Fe alloy was successfully fabricated. The composite coating consisted of a NiO matrix and homogeneously distributed criss-cross intragranular and intergranular NiFe₂O₄ precipitates, with a very dense and flat structure. The composite, compared to bare Ni metal, exhibited increased hot corrosion resistance under an atmosphere of Na₃AlF₆–AlF₃–CaF molten salts and air at 960 °C, mainly because of the dense structure and well-adhered, homogeneously dispersed intragranular and intergranular NiFe₂O₄ precipitates.     

Aluminizing and boroaluminizing treatments of Mar-M247 and their effect on hot corrosion resistance in Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>−NaCl molten salt

The effect of surface modifications of Mar-M247 superalloy on hot corrosion resistance was examined in Na₂SO₄−NaCl molten salt. The Mar-M247 was aluminized and boroaluminized by pack cementation in Ar and underwent a cyclic hot corrosion test in Na₂SO₄−NaCl molten salt. The XRD results showed that a Ni₂Al₃ phase was formed between the aluminized layer and the substrate when the surface modification temperature was below 1273 K. However, a NiAl phase formed when the temperature was above 1273 K. The intensity of the XRD peak in the NiAl phase increased after post heat treatment. Hot corrosion resistance increased for the specimens containing NiAl rather than Ni₂Al₃ phase. The ductile NiAl phase suppressed the potential for crack initiation during thermal cycling. Post heat treatment increased the corrosion resistance of the aluminized layer for Mar-M247, which underwent surface modification at 1273 K and above. In the boroaluminized Mar-M247 specimens, corrosion resistance decreased as a result of the blocking of outward diffusion of Cr by boron and decreased cohesion between the oxide scale and the aluminized layer during thermal cycling.     

The structure and high temperature corrosion performance of medium-thickness aluminide coatings on nickel-based superalloy GTD-111

Simple and Si-modified aluminide coatings having medium-thickness (40-60 μm) have been applied on the superalloy GTD-111 by a slurry technique. Hot corrosion and cyclic oxidation performance of the uncoated and the coated superalloy were investigated by exposing samples to a molten film of Na₂SO₄-40 %wt NaVO₃-10%wt NaCl at 780 °C and 1 h cyclic oxidation at 1100 °C in air, respectively. The presence of silicon in the aluminide structure increased the oxidation resistance by a factor of 1.7 times. In addition, a SiO₂-containing scale, which formed on the Si-containing coating surface, was stable during of the hot corrosion testing.     

Hot corrosion behaviour of plasma sprayed YSZ/Al2O3 dispersed NiCrAlY coatings on Inconel-718 superalloy

Oxide dispersed NiCrAlY bond coatings have been developed for enhancing thermal life cycles of thermal barrier coatings (TBCs). However, the role of dispersed oxides on high temperature corrosion, in particular hot corrosion, has not been sufficiently studied. Therefore, the present study aims to improve the understanding of the effect of YSZ dispersion on the hot corrosion behaviour of NiCrAlY bond coat. For this, NiCrAlY, NiCrAlY + 25 wt.% YSZ, NiCrAlY + 50 wt.% YSZ and NiCrAlY + 75 wt.% YSZ were deposited onto Inconel-718 using the air plasma spraying (APS) process. Hot corrosion studies were conducted at 800 °C on these coatings after covering them with a 1:1 weight ratio of Na₂SO₄ and V₂O₅ salt film. Hot corrosion kinetics were determined by measuring the weight gain of the specimens at regular intervals for a duration of 51 h. X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy techniques were used to determine the nature of phases formed, examine the surface attack and to carry out microanalysis of the hot corroded coatings respectively. The results show that YSZ dispersion causes enhanced hot corrosion of the NiCrAlY coating. Leaching of yttria leads not only to the formation of the YVO₄ phase but also the destabilization of the YSZ by hot corrosion. For the sake of comparison, the hot corrosion behaviour of a NiCrAlY + 25 wt.% Al₂O₃ coating was also examined. The study shows that the alumina dispersed NiCrAlY bond coat offers better hot corrosion resistance than the YSZ dispersed NiCrAlY bond coat, although it is also inferior compared to the plain NiCrAlY bond coat.     

Tribological and anti-corrosion properties of Ni-W-CeO2 coatings against molten glass

Composite plating was used to prepare Ni-W infused rare earth oxide CeO₂ composite coatings. The high temperature friction behavior and corrosion resistance of the coatings against molten glass were investigated by using a high temperature tribometer. A microhardness tester and an environmental scanning electron microscope equipped energy dispersive spectroscopy were employed to investigate the microhardness and the surface morphology of the composite coatings respectively. The results show that the brittle fracture, high temperature tribological properties and the corrosion resistance of Ni-W infused CeO₂ coatings are superior to those of a standard Ni-W coating. CeO₂ particles decrease the friction coefficient from nearly 0.5 to about 0.25 during the composite coatings sliding against the molten glass at about 973 K, and proper quantities of CeO₂ decrease the variation of the friction coefficient value. Furthermore, CeO₂ can improve the corrosion resistance of the Ni-W coatings at high temperature effectively.     

Oxidation resistance and corrosion behavior of hot-dip aluminized coatings on commercial-purity titanium

Aluminizing is an effective method to protect alloys from oxidation and corrosion. In this article, the microstructure, morphology, phase composition of the aluminized layers and the oxide films were investigated by SEM, EDS and X-ray diffraction. The high temperature oxidation resistance and electrochemical behavior of hot dip aluminizing coatings on commercial-purity titanium had been studied by cyclic oxidation test and potentiodynamic polarization technique. The results show that the reaction between the titanium and the molten aluminum leads to form an aluminum coating which almost has the composition of the aluminum bath. After diffusion annealing at 950 °C for 6 h, the aluminum coating transformed into a composite layer, which was composed of an inner layer and an outer layer. The inner layer was identified as Ti₃Al or Ti₂Al phase, and the outer layer was TiAl₃ and Al₂O₃ phase. The cyclic oxidation treatment at 1000 °C for 51 h shows that the oxidation resistance of the diffused titanium is 13 times more than the bare titanium. And the formation of TiAl₃, θ-Al₂O₃ and compact α-Al₂O₃ at the outer layer was thought to account for the improvement of the oxidation resistance at high temperature. However, the corrosion resistance of the aluminized titanium and the diffused titanium were reduced in 3.5 wt.% NaCl solution. The corrosion resistance of the aluminized titanium was only one third of bare titanium. Moreover, the corrosion resistance of the diffused titanium was far less than bare titanium.     

Antibacterial activities and corrosion behavior of novel PEO/nanostructured ZrO2 coating on Mg alloy

Plasma electrolytic oxidation (PEO) was developed as a bond coat for air plasma sprayed (APS) nanostructure ZrO₂ as top coat to enhance the corrosion resistance and antibacterial activity of Mg alloy. Corrosion behavior and antibacterial activities of coated and uncoated samples were assessed by electrochemical tests and agar diffusion method toward Escherichia coli (E. coli) bacterial pathogens, respectively. The lowest corrosion current density and the highest charge transfer resistance, phase angle and impedance modulus were observed for PEO/nano-ZrO₂ coated sample compared with those of PEO coated and bare Mg alloys. Nano-ZrO₂ top coat which has completely sealed PEO bond coat is able to considerably delay aggressive ions transportation towards Mg alloy surface and significantly enhances corrosion resistance of Mg alloy in simulated body fluid (SBF) solution. Moreover, higher antibacterial activity was also observed in PEO/nano-ZrO₂ coating against bacterial strains than that of the PEO coated and bare Mg alloys. This observation was attributed to the presence of ZrO₂ nanoparticles which decelerate E. coli growth as a result of E. coli membranes.     

Performance of high-velocity oxyfuel-sprayed coatings on an Fe-based superalloy in Na2SO4-60%V2O5 environment at 900 °C part II: Hot corrosion behavior of the coatings

NiCrBSi, Cr₃C₂-NiCr, Ni-20Cr, and Stellite-6 coatings were deposited on an Fe-based superalloy by the high-velocity oxyfuel (HVOF) thermal spray process. The hot corrosion behavior of the coatings in an aggressive environment of Na₂SO₄-60%V₂O₅ at 900 °C under cyclic conditions was studied. The thermogravimetric technique was used to establish the kinetics of corrosion. X-ray diffraction, scanning electron microscopy/energy-dispersive x-ray and electron probe microanalysis techniques were used to analyze the corrosion products. Hot corrosion resistances of all the coatings were found to be better than the uncoated superalloy. The Ni-20Cr coating was found to be the most protective, followed by Cr₃C₂-NiCr coatings. The Ni-20Cr coating had reduced the mass gain by 90% of that gained by the uncoated superalloy. The hot corrosion resistance shown by the Cr₃C₂-NiCr coating was slightly better compared with the NiCrBSi coating; however, both of the coatings performed better than the Stellite-6 coating. The Stellite-6 coating was the least effective among the coatings studied, but it was still successful in decreasing the mass gain to about one fourth compared with the uncoated superalloy. The formation of oxides and spinels of nickel, chromium, or cobalt may be contributing to the development of hot corrosion resistance in the coatings. This article focuses on the hot corrosion behavior of HVOF coatings. The characterization of these coatings has been presented in part I included in this issue.     

Degradation behaviour of ZrO2-Ni/Al gradient coatings in molten Zn

In order to improve the corrosion resistance of metallic materials in molten zinc, ZrO₂-Ni/Al gradient coatings were sprayed on the surface of the Fe-0.35-0.44 wt.% C steel. The corrosion behaviour and corrosion mechanism of the ZrO₂-Ni/Al gradient coatings in molten zinc were studied. The ZrO₂-Ni/Al gradient coatings on the surface of steels prolonged the lifetime of samples and changed the corrosion behaviour of the samples in molten zinc. The lifetime of the ZrO₂-Ni/Al gradient coatings immersed in molten zinc at 620 °C is 28 days, which is 4 times as long as that of the general ZrO₂ coatings. The ZrO₂-Ni/Al gradient coatings were corroded in molten zinc at 620 °C, which was caused by zinc atom diffusing along the crystal boundary and pores of the ZrO₂-Ni/Al gradient coatings, and reacting with Ni/Al particle in the ZrO₂-Ni/Al gradient coatings. The corrosion mechanism of the coatings in molten zinc at 620 °C was crystal boundary corrosion, pitting corrosion and reaction corrosion.     

Effects of bond coat preoxidation on the properties of ZrO2-8wt.% Y2O3/Ni-22Cr-10Al-1Y thermal-barrier coatings

Plasma-sprayed thermal barrier coatings (TBCs) consist of an intermediate MCrAlY bond coat to protect the substrate superalloy from oxidation/hot corrosion and a thermal insulating zirconia-based ceramic top coat. This system is developed for advanced turbine-engine, hot-section components. In this study the as-sprayed Ni-22Cr-10Al-1Y bond coat was subjected to preoxidation treatment at 1000° C for 1, 50, 100, and 200 hr, also at 1100°C, 1200°C and 1300°C for 1 hr to form an oxide scale before subsequent deposition of a ZrO₂-8wt.% Y₂O₃ top coat. The oxidation kinetics were measured, and the phase constitution and morphology of pregrown oxides on the Ni-22Cr-1Y bond coat were analyzed by x-ray diffractometer and SEM/EDS to elucidate the improvement and degradation mechanisms of the new system. The results of the experiments in this study showed that the tentative ZrO₂-8wt.% Y₂O₃ TBC specimens with preoxidized Ni-22Cr-10Al-1Y bond coat, when properly processed, exhibited lower oxidation rates and generally longer lifetime compared with traditional TBC specimens.     

The EIS investigation of powder polyester coatings on phosphated low carbon steel: The effect of NaNO2 in the phosphating bath

The effect of different type of iron-phosphate coatings on corrosion stability and adhesion characteristic of top powder polyester coating on steel was investigated. Iron-phosphate coatings were deposited on steel in the novel phosphating bath with or without NaNO₂ as an accelerator. The corrosion stability of the powder polyester coating was evaluated by electrochemical impedance spectroscopy (EIS), adhesion by pull-off and NMP test, while surface morphology of phosphate coatings were investigated by atomic force microscopy (AFM).The adhesion and corrosion stability of powder polyester coatings were improved with pretreatment based on iron-phosphate coating deposited from NaNO₂-free bath.     

Hot corrosion behaviour of Yb2Zr2O7 ceramic coated with V2O5 at temperatures of 600-800 °C in air

To better understand the hot corrosion behaviour of Yb₂Zr₂O₇ ceramic in molten V₂O₅, hot corrosion experiments were performed in a temperature range of 600-800 °C in air. Different reaction products of ZrV₂O₇, YbVO₄ and m-ZrO₂ were identified depending upon the hot corrosion conditions, for example, ZrV₂O₇ and YbVO₄ at 600 °C for 2 h and 8 h; ZrV₂O₇, m-ZrO₂ and YbVO₄ at 700 °C for 2 h; m-ZrO₂ and YbVO₄ either at 800 °C for 2 h or at 700-800 °C for 8 h. The hot corrosion reaction mechanisms were further discussed based on the thermal instability of ZrV₂O₇ at elevated temperatures.     

Investigations on role of HVOF sprayed Co and Ni based coatings to combat hot corrosion

Abstract

This paper aims to investigate the hot corrosion resistance of high velocity oxy-fuel (HVOF) sprayed cobalt based (Stellite-6) and nickel based (Ni–20Cr) coatings deposited on the superalloy Superni-718 (Ni–19Cr–18˙5Fe–5˙13Ta–3˙05Mo–0˙9Ti–0˙5AI–0˙18Mn–0˙18Si–0˙15Cu–0˙04C) in the Na₂SO₄–60%V₂O₅ salt environment at 900°C under cyclic conditions. The X-ray diffractometry, scanning electron microscopy/energy dispersive analysis and electron probe microanalyser techniques were used to study the corrosion products with respect to their morphology, phase composition and element concentration. The thermogravimetric technique was used to establish the kinetics of corrosion. The bare alloy underwent severe hot corrosion attack. The Ni–20Cr coating shows excellent hot corrosion resistance with negligible spallation, whereas Stellite-6 coating reveals less hot corrosion resistance and more spallation. The hot corrosion resistance of Ni–20Cr coating has been attributed to the formation of oxides of chromium, nickel and spinel of nickel chromium. The oxides of silicon, chromium, cobalt and spinels of cobalt–chromium and nickel–chromium have contributed for hot corrosion resistance of Stellite-6 coatings.     

高温防护涂层的熔盐热腐蚀研究进展

高温热腐蚀是热元件主要失效形式之一,Na₂SO₄和NaCl熔盐会加速高温下的热腐蚀,甚至导致灾难性事故发生。本文就Na₂SO₄和/或NaCl熔盐引起的热腐蚀进行了讨论,其中Na₂SO₄是主要的腐蚀反应物,详细介绍了2种典型的热腐蚀行为和性能特点。重点介绍了几种热腐蚀模型和机理,以及Na₂SO₄、NaCl、Na₂SO₄+NaCl熔盐的反应公式和腐蚀机理。根据目前的研究状况来看,制备防护涂层是缓解热腐蚀的最佳途径,总结了近年来MCrAlY涂层、NiAl涂层、热障涂层和新型涂层的发展情况,并探讨了进一步提高涂层耐腐蚀性能的方法。最后,展望了防护涂层的未来发展方向。