AlN/GaN Insulated-Gate HEMTs With 2.3 A/mm Output Current and 480 mS/mm Transconductance

High-electron mobility transistors (HEMTs) based on ultrathin AlN/GaN heterostructures with a 3.5-nm AlN barrier and a 3-nm $hbox{Al}_{2}hbox{O}_{3}$ gate dielectric have been investigated. Owing to the optimized AlN/GaN interface, very high carrier mobility $(sim!!hbox{1400} hbox{cm}^{2}/hbox{V}cdothbox{s})$ and high 2-D electron-gas density $(sim!!kern1pthbox{2.7} times hbox{10}^{13} /hbox{cm}^{2})$ resulted in a record low sheet resistance $(sim !!hbox{165} Omega/hbox{sq})$. The resultant HEMTs showed a maximum dc output current density of $simkern1pt$2.3 A/mm and a peak extrinsic transconductance $g_{m,{rm ext}} sim hbox{480} hbox{mS/mm}$ (corresponding to $g_{m,{rm int}} sim hbox{1} hbox{S/mm}$). An $f_{T}/f_{max}$ of 52/60 GHz was measured on $hbox{0.25} times hbox{60} muhbox{m}^{2}$ gate HEMTs. With further improvements of the ohmic contacts, the gate dielectric, and the lowering of the buffer leakage, the presented results suggest that, by using AlN/GaN heterojunctions, it may be possible to push the performance of nitride HEMTs to current, power, and speed levels that are currently unachievable in AlGaN/GaN technology.      

AlGaN/GaN HEMTs With Low Leakage Current and High On/Off Current Ratio

In this letter, we propose using an oxide-filled isolation structure followed by $hbox{N}_{2}/hbox{H}_{2}$ postgate annealing to reduce the leakage current in AlGaN/GaN HEMTs. An off-state drain leakage current that is smaller than $hbox{10}^{-9} hbox{A/mm}$ (minimum $hbox{5.1} times hbox{10}^{-10} hbox{A/mm}$) can be achieved, and a gate leakage current in the range of $hbox{7.8} times hbox{10}^{-10}$ to $hbox{9.2} times hbox{10}^{-11} hbox{A/mm}$ ($V_{rm GS}$ from $-$10 to 0 V and $V_{rm DS} = hbox{10} hbox{V}$) is obtained. The substantially reduced leakage current results in an excellent on/off current ratio that is up to $hbox{1.5} times hbox{10}^{8}$. An improved flicker noise characteristic is also observed in the oxide-filled devices compared with that in the traditional mesa-isolated GaN HEMTs.      

Gate-First AlGaN/GaN HEMT Technology for High-Frequency Applications

This letter describes a gate-first AlGaN/GaN high-electron mobility transistor (HEMT) with a W/high- $k$ dielectric gate stack. In this new fabrication technology, the gate stack is deposited before the ohmic contacts, and it is optimized to stand the 870 $^{circ}hbox{C}$ ohmic contact annealing. The deposition of the W/high-$k$ dielectric protects the intrinsic transistor early in the fabrication process. Three different gate stacks were studied: $hbox{W}/ hbox{HfO}_{2}$, $hbox{W}/hbox{Al}_{2}hbox{O}_{3}$ , and $hbox{W}/hbox{HfO}_{2}/hbox{Ga}_{2}hbox{O}_{3}$ . DC characterization showed transconductances of up to 215 mS/mm, maximum drain current densities of up to 960 mA/mm, and more than five orders of magnitude lower gate leakage current than in the conventional gate-last Ni/Au/Ni gate HEMTs. Capacitance–voltage measurements and pulsed-$IV$ characterization show no hysteresis for the $hbox{W}/hbox{HfO}_{2}/ hbox{Ga}_{2}hbox{O}_{3}$ capacitors and low interface traps. These W/high- $k$ dielectric gates are an enabling technology for self-aligned AlGaN/GaN HEMTs, where the gate contact acts as a hard mask to the ohmic deposition.      

High Microwave-Noise Performance of AlGaN/GaN MISHEMTs on Silicon With Gate Insulator Grown by ALD

High microwave-noise performance is realized in AlGaN/GaN metal–insulator semiconductor high-electron mobility transistors (MISHEMTs) on high-resistivity silicon substrate using atomic-layer-deposited (ALD) $hbox{Al}_{2}hbox{O}_{3}$ as gate insulator. The ALD $hbox{Al}_{2}hbox{O}_{3}/hbox{AlGaN/GaN}$ MISHEMT with a 0.25- $muhbox{m}$ gate length shows excellent microwave small signal and noise performance. A high current-gain cutoff frequency $f_{T}$ of 40 GHz and maximum oscillation frequency $f_{max}$ of 76 GHz were achieved. At 10 GHz, the device exhibits low minimum-noise figure $(hbox{NF}_{min})$ of 1.0 dB together with high associate gain $(G_{a})$ of 10.5 dB and low equivalent noise resistance $(R_{n})$ of 29.2 $Omega$. This is believed to be the first report of a 0.25-$muhbox{m}$ gate-length GaN MISHEMT on silicon with such microwave-noise performance. These results indicate that the AlGaN/GaN MISHEMT with ALD $hbox{Al}_{2}hbox{O}_{3}$ gate insulator on high-resistivity Si substrate is suitable for microwave low-noise applications.      

Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

AlGaN/GaN MOSHEMTs With Liquid-Phase-Deposited $ hbox{TiO}_{2}$ as Gate Dielectric

$hbox{TiO}_{2}$ films deposited on GaN layers at room temperature through a simple and low-cost liquid-phase deposition (LPD) method are investigated and served as gate dielectrics in AlGaN/GaN MOSHEMTs. The electrical characteristics of the MOS structure on n-doped GaN show that the leakage current is about $hbox{1.01} times hbox{10}^{-7} hbox{A/cm}^{2}$ at 1 MV/cm and that the breakdown field is more than 6.5 MV/cm. The maximum drain current density of MOSHEMTs is higher than that of conventional HEMTs, and a wider gate voltage swing can also be observed. The maximum transconductance and threshold voltage almost maintain the same characteristics, even after inserting a dielectric layer between the gate metal and the 2DEG channel by using $ hbox{TiO}_{2}$ as a gate dielectric. The gate leakage current density is significantly improved, and the bias stress measurement shows that current collapse is much suppressed for MOSHEMTs.      

30-GHz Low-Noise Performance of 100-nm-Gate-Recessed n-GaN/AlGaN/GaN HEMTs

We demonstrate a 100-nm-gate-recessed n-GaN/AlGaN/GaN high-electron mobility transistor (HEMT) with low-noise properties at 30 GHz. The recessed GaN HEMT exhibits a low ohmic-contact resistance of 0.28 $Omega cdot hbox{mm}$ and a low gate leakage current of 0.9 $muhbox{A/mm}$ when biased at $V_{rm GS} = -hbox{3} hbox{V}$ and $V_{rm DS} = hbox{10} hbox{V}$. At the same bias point, a minimum noise figure of 1.6 dB at 30 GHz and an associated gain of 5 dB were achieved. To the best of our knowledge, this is the best noise performance reported at 30 GHz for gate-recessed AlGaN/GaN HEMTs.      

Breakdown Enhancement of AlGaN/GaN HEMTs on 4-in Silicon by Improving the GaN Quality on Thick Buffer Layers

We have achieved a 9- $muhbox{m}$-thick AlGaN/GaN high-electron mobility transistor (HEMT) epilayer on silicon using thick buffer layers with reduced dislocation density $(D_{D})$. The crack-free 9- $muhbox{m}$-thick epilayer included 2- $muhbox{m}$ i-GaN and 7- $ muhbox{m}$ buffer. The HEMTs fabricated on these devices showed a maximum drain–current density of 625 mA/mm, transconductance of 190 mS/mm, and a high three-terminal OFF breakdown of 403 V for device dimensions of $L_{g}/W_{g}/L_{rm gd} = hbox{1.5/15/3} muhbox{m}$ . Without using a gate field plate, this is the highest $BV$ reported on an AlGaN/GaN HEMT on silicon for a short $L_{rm gd}$ of 3 $muhbox{m}$. A very high $BV$ of 1813 V across 10- $mu hbox{m}$ ohmic gap was achieved for i-GaN grown on thick buffers. As the thickness of buffer layers increased, the decreased $D_{D}$ of GaN and increased resistance between surface electrode and substrate yielded a high breakdown.      

Localized Damage in AlGaN/GaN HEMTs Induced by Reverse-Bias Testing

Reverse-bias testing in AlGaN/GaN HEMTs at high (negative) gate voltage is found to induce a catastrophic increase in gate leakage current $I_{G}$, with only a slight degradation of drain current $I_{D}$. Electroluminescence (EL) microscopy demonstrates that leakage current injection is localized within “hot spots” at the gate edges, possibly corresponding to defects in the semiconductor material or at the metal–semiconductor interface. The density of “hot spots” increases during tests and is correlated with the increase of $I_{G}$ and electroluminescence intensity and with an enhancement of trapping effects such as current collapse.      

High-Performance 0.1-$muhbox{m}$ Gate AlGaN/GaN HEMTs on Silicon With Low-Noise Figure at 20 GHz

The realization of high-performance 0.1-$muhbox{m}$ gate AlGaN/GaN high-electron mobility transistors (HEMTs) grown on high-resistivity silicon substrates is reported. Our devices feature cutoff frequencies as high as $f_{T} = hbox{75} hbox{GHz}$ and $f_{rm MAX} = hbox{125} hbox{GHz}$, the highest values reported so far for AlGaN/GaN HEMTs on silicon. The microwave noise performance is competitive with results achieved on other substrate types, such as sapphire and silicon carbide, with a noise figure $F = hbox{1.2}{-}hbox{1.3} hbox{dB}$ and an associated gain $G_{rm ass} = hbox{8.0}{-}hbox{9.5} hbox{dB}$ at 20 GHz. This performance demonstrates that GaN-on-silicon technology is a viable alternative for low-cost millimeter-wave applications.      

High-Performance Poly-Silicon TFTs Using a High-$k$ $hbox{PrTiO}_{3}$ Gate Dielectric

In this letter, a polycrystalline-silicon thin-film transistor (poly-Si TFT) with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is proposed for the first time. Compared to TFTs with a $hbox{Pr}_{2}hbox{O}_{3}$ gate dielectric, the electrical characteristics of poly-Si TFTs with a $hbox{PrTiO}_{3}$ gate dielectric can be significantly improved, such as lower threshold voltage, smaller subthreshold swing, higher $I_{rm on}/I_{rm off}$ current ratio, and larger field-effect mobility, even without any hydrogenation treatment. These improvements can be attributed to the high gate capacitance density and low grain-boundary trap state. All of these results suggest that the poly-Si TFT with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is a good candidate for high-speed and low-power display driving circuit applications in flat-panel displays.      

First Internal Spacers' Introduction in Record High $I_{rm ON}/I_{rm OFF} hbox{TiN/HfO}_{2}$ Gate Multichannel MOSFET Satisfying Both High-Performance and Low Standby Power Requirements

For the first time, internal spacers have been introduced in multichannel CMOSFET (MCFET) structures, featuring a decrease of the intrinsic $CV/I$ delay by 39%. The process steps introduced for this new MCFET technological option are studied and optimized in order to achieve excellent $I_{rm ON}/I_{rm OFF}$ characteristics (NMOS: 2.33 $hbox{mA}/muhbox{m}$ at 27 $hbox{pA}/muhbox{m}$ and PMOS: 1.52 $hbox{mA}/muhbox{m}$ at 38 $hbox{pA}/muhbox{m}$). A gate capacitance $C_{rm gg}$ reduction of 32% is measured, thanks to $S$-parameter extraction. Moreover, a significant improvement of the analogical figure of merit is measured compared with optimized fully depleted silicon-on-insulator planar reference; the voltage gain $A_{rm VI}(= g_{m}/g_{rm ds})$ is improved by 92%.      

Multi-Channel Field-Effect Transistor (MCFET)—Part I: Electrical Performance and Current Gain Analysis

Multi-Channel Field-Effect Transistor (MCFET) structures with ultralow $I_{ rm OFF}$ (16 $hbox{pA}/muhbox{m}$) and high $I_{rm ON}$ (N: 2.27 $ hbox{mA}/muhbox{m}$ and P: 1.32 $hbox{mA}/muhbox{m}$ ) currents are obtained on silicon on insulator (SOI) with a high-$ kappa$/metal gate stack, satisfying both low-standby-power and high-performance requirements. The experimental current gain of the MCFET structure is compared with that of an optimized planar FD-SOI reference with the same high-$kappa$/metal gate stack and is quantitatively explained by an analytical model. Transport properties are investigated, and the specific MCFET electrostatic properties are evidenced, in particular a higher $V_{rm Dsat}$ for MCFETs compared with the planar reference. Finally, through 3-D numerical simulations correlated with specific characterizations, the influence of the channel width on the electrical performance is analyzed. For narrow devices, the parasitic bottom channel increases the total drain current of the MCFET structure without degrading the electrostatic integrity.      

Increase of Breakdown Voltage on AlGaN/GaN HEMTs by Employing Proton Implantation

The breakdown voltage of new AlGaN/GaN high electron mobility transistors (HEMTs) was increased considerably without sacrificing any other electrical characteristics by proton implantation. The breakdown voltage of proton-implanted AlGaN/GaN HEMTs with 150 KeV $hbox{1}times hbox{10}^{14} hbox{-}hbox{cm}^{-2}$ fluence after thermal annealing at 400 $^{circ}hbox{C}$ for 5 min under $hbox{N}_{2}$ ambient was 719 V, while that of conventional device was 416 V. The increase of the breakdown voltage is attributed to the expansion of the depletion region under the 2-D electron gas (2-DEG) channel. The depletion region expanded downward into the GaN buffer layer because implanted protons acted as positive ions and attracted electrons in the 2-DEG channel.      

Low-Voltage Organic Field-Effect Transistor With PMMA/$ hbox{ZrO}_{2}$ Bilayer Dielectric

This paper reports on the application of a bilayer polymethylmethacrylate (PMMA)/ $hbox{ZrO}_{2}$ dielectric in copper phthalocyanine (CuPc) organic field-effect transistors (OFETs). By depositing a PMMA layer on $hbox{ZrO}_{2}$, the leakage of the dielectric is reduced by one order of magnitude compared to single-layer $hbox{ZrO}_{2}$. A high-quality interface is obtained between the organic semiconductor and the combined insulators. By integrating the advantages of polymer and high- $k$ dielectrics, the device achieves both high mobility and low threshold voltage. The typical field-effect mobility, threshold voltage, on/off current ratio, and subthreshold slope of OFETs with bilayer dielectric are $hbox{5.6}timeshbox{10}^{-2} hbox{cm}^{2}/hbox{V} cdot hbox{s}$, 0.8 V, $hbox{1.2} times hbox{10}^{3}$, and 2.1 V/dec, respectively. By using the bilayer dielectrics, the hysteresis observed in the devices with single-layer $hbox{ZrO}_{2}$ is no longer present.      

Dopant-Segregated Schottky Silicon-Nanowire MOSFETs With Gate-All-Around Channels

In this letter, we demonstrated dopant-segregated Schottky (DSS) p-MOSFET with gate-all-around silicon-nanowire (SiNW) channel of 10 nm in diameter. The DSS transistor shows improved performance as compared to a reference Schottky barrier (SB) transistor without dopant segregation. The DSS transistor shows $I_{rm ON}$ of 319 $mu hbox{A}/muhbox{m}$ at a low gate overdrive of $-$ 0.6 V, high $I_{rm ON}/I_{rm OFF}$ ratio $(sim!hbox{10}^{5})$, and short-channel performance with subthreshold slope $sim$90 mV/dec down to 100-nm gate length with relatively thick (6 nm) deposited gate oxide. The DSS transistor also shows significant reduction ( $sim!hbox{40}times$ lower) in the series resistance as compared to the SB transistor. The origin of the improved performance of the DSS is the thin dopant layer segregated at the nickel monosilicide/SiNW point contact which results in the enhanced hole injection at the source side and the suppressed electron injection at the drain side.      

Gate-Recessed InAlN/GaN HEMTs on SiC Substrate With $ hbox{Al}_{2}hbox{O}_{3}$ Passivation

We studied submicrometer $(L_{G} = hbox{0.15} {-} hbox{0.25} mu hbox{m})$ gate-recessed InAlN/AlN/GaN high-electron mobility transistors (HEMTs) on SiC substrates with 25-nm $hbox{Al}_{2}hbox{O}_{3}$ passivation. The combination of a low-damage gate-recess technology and the low sheet resistance of the InAlN/AlN/GaN structure resulted in HEMTs with a maximum dc output current density of $I_{{rm DS}, max} = hbox{1.5} hbox{A/mm}$ and a record peak extrinsic transconductance of $g_{m, {rm ext}} = hbox{675} hbox{mS/mm}$. The thin $hbox{Al}_{2}hbox{O}_{3}$ passivation improved the sheet resistance and the transconductance of these devices by 15% and 25%, respectively, at the same time that it effectively suppressed current collapse.      

Impacts of $hbox{N}_{2}$ and $hbox{NH}_{3}$ Plasma Surface Treatments on High-Performance LTPS-TFT With High-$kappa$ Gate Dielectric

Low-temperature polycrystalline-silicon thin-film transistors (LTPS-TFTs) with high- $kappa$ gate dielectrics and plasma surface treatments are demonstrated for the first time. Significant field-effect mobility $mu_{rm FE}$ improvements of $sim$86.0% and 112.5% are observed for LTPS-TFTs with $hbox{HfO}_{2}$ gate dielectric after $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments, respectively. In addition, the $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments can also reduce surface roughness scattering to enhance the field-effect mobility $mu_{rm FE}$ at high gate bias voltage $V_{G}$, resulting in 217.0% and 219.6% improvements in driving current, respectively. As a result, high-performance LTPS-TFT with low threshold voltage $V_{rm TH} sim hbox{0.33} hbox{V}$, excellent subthreshold swing S.S. $sim$0.156 V/decade, and high field-effect mobility $mu_{rm FE} sim hbox{62.02} hbox{cm}^{2}/hbox{V} cdot hbox{s}$ would be suitable for the application of system-on-panel.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

Microwave ZnO Thin-Film Transistors

We have developed ZnO thin-film transistor design and fabrication techniques to demonstrate microwave frequency operation with 2-$muhbox{m}$ gate length devices produced on GaAs substrates. Using $hbox{SiO}_{2}$ gate insulator and pulsed laser deposited ZnO active layers, a drain–current on/off ratio of $hbox{10}^{12}$, a drain–current density of 400 mA/mm, a field-effect mobility of $hbox{110} hbox{cm}^{2}!/ hbox{V}!cdothbox{s}$, and a subthreshold gate voltage swing of 109 mV/dec were achieved. Devices with Ti-gate metal had current and power gain cutoff frequencies of 500 and 400 MHz, respectively.