Phase pure synthesis of BiFeO3 nanopowders using diverse precursor via co-precipitation method

Amorphous powder of BiFeO₃ (BFO) was synthesized at low-temperature (80 °C) by co-precipitation method. Optimal synthesis conditions for phase pure BFO were obtained. Powders were calcined in the temperature range from 400 to 600 °C for 1 h. Iso-statically pressed powder was sintered at 500 °C for 2 h. Differential scanning calorimetric thermo-gram guided for phase transition, crystallization and melting temperatures. X-ray diffraction confirmed the amorphous nature of as synthesized powder and phase formation of calcined powders. Calcination at temperature ≥400 °C resulted in nano crystalline powders with perovskite structure. Average crystallite size increased with the increase in calcination temperature. Scanning electron microscopic studies revealed dense granular microstructure of the sintered samples. The sintered samples exhibited high dc resistivity at room temperature which decreased with the increase in temperature. Dielectric constant, dielectric loss tangent and ac conductivity measurements were carried out in the frequency range (10 Hz to 2 MHz). The samples responded weak electric and magnetic polarization at room temperature with unsaturated and hysteresis free loops, respectively.     

Synthesis, structural and microwave dielectric properties of Al2W3−xMoxO12 (x = 0-3) ceramics

Low dielectric ceramics in the Al₂W_3−xMo_xO₁₂ (x = 0-3) system have been prepared through solid state ceramic route. The phase purity of the ceramic compositions has been studied using powder X-ray diffraction (XRD) studies. The microstructure of the sintered ceramics was evaluated by Scanning Electron Microscopy (SEM). The crystal structure of the ceramic compositions as a result of Mo substitution has been studied using Laser Raman spectroscopy. The microwave dielectric properties of the ceramics were studied by Hakki and Coleman post resonator and cavity perturbation techniques. Al₂Mo_xW_3−xO₁₂ (x = 0-3) ceramics exhibited low dielectric constant and relatively high unloaded quality factor. The temperature coefficient of resonant frequency of the compositions is found to be in the range −41 to −72 ppm/°C.     

High-dielectric-constant and low-loss microwave dielectric in the (1 − x)La(Mg0.5Ti0.5)O3-x(Ca0.8Sr0.2)TiO3 solid solution system

The microwave dielectric properties and microstructures of (1 − x)La(Mg_0.5Ti_0.5)O₃-x(Ca_0.8Sr_0.2)TiO₃ ceramics, prepared by a mixed oxide route, have been investigated. The forming of solid solutions was confirmed by the XRD patterns and the measured lattice parameters for all compositions. A near zero τ_f was achieved for samples with x = 0.5, although the dielectric properties varied with sintering temperature. The Q × f value of 0.5La(Mg_0.5Ti_0.5)O₃-0.5(Ca_0.8Sr_0.2)TiO₃ increased up to 1475 °C, after which it decreased. The decrease in dielectric properties was coincident with the onset of rapid grain growth. The optimum combination of microwave dielectric properties was achieved at 1475 °C for samples where x = 0.5 with a dielectric constant ?_r of 47.12, a Q × f value of 35,000 GHz (measured at 6.2 GHz) and a τ_f value of −4.7 ppm/°C.     

Dielectric properties of low-temperature sintered Ba0.6Sr0.4TiO3 thick films prepared by reactive sintering method

Screen printed Ba_0.6Sr_0.4TiO₃ (BST6/4) thick films were fabricated by reactive sintering at a low temperature below 900 °C. The dielectric properties in radio frequency range were measured on samples of sandwich structure MIM capacitors by impedance analyzer, while that in microwave frequency range were measured on samples of thick films without top and bottom electrodes by split-post dielectric resonator method. The thick films exhibited a low permittivity, while at the same time, maintained a high tunability. The permittivity and dielectric loss at 1 MHz were 228.8 and 0.007, respectively. The corresponding values measured at 9.9 GHz were 82.24 and 0.109, respectively. The tunability was as high as 72.4% (150 kV/cm, 10 kHz). This method provides a simple and effective route to obtain thick films with great potential in applications in Low Temperature Co-fired Ceramic (LTCC) and microwave tunable devices.     

Microwave properties of Ba(Zn1/3Ta2/3)O3 dielectric resonators

Ba(Zn_1/3Ta_2/3)O₃ (BZT) dielectric resonators were prepared by solid-state reaction. The starting materials were BaCO₃, ZnO, and Ta₂O₅ powders with high purity. The double calcined BZT pellets were sintered in air at temperatures of 1575, 1600, 1625, and 1650 °C for 4 h. The X-ray diffraction data allowed the study of the unit cell distortion degree and the presence of the secondary phases. A long-range order with a 2:1 ratio of Ta and Zn cations on the octahedral positions of the perovskite structure was observed with the increase of the sintering temperature. The dielectric constant of BZT resonators measured around 6 GHz was between 26 and 28. High values of Q × f product (120 THz) were obtained for BZT resonators sintered at 1650 °C/4 h. The temperature coefficient of the resonance frequency exhibits positive values less than 6 ppm/°C. The achieved dielectric parameters recommend BZT dielectric resonators for microwave and millimeter wave applications.     

Low-temperature synthesis of α- and β-MoSi2 powders using Na

Molybdenum disilicide powders were prepared by heating a mixture of Mo and Si powders with Na metal. The single phases of β-MoSi₂ and α-MoSi₂ powders were obtained at 873 K and 1073 K, respectively. The preparation temperature of the single phase α-MoSi₂ powder was 500 K lower than that of the conventional solid state reaction method using Mo and Si powders. The grain size of both MoSi₂ powders was less than 2 μm, and their shape was angular and irregular.     

Low-firable high-K dielectric in the Zrx(Zn1/3Nb2/3)1−xTiO4 ceramic system

Composite ceramics in the solid solution of Zr_x(Zn_1/3Nb_2/3)_1−xTiO₄ (x = 0.1-0.4) have been prepared by the mixed oxide route. Formation of solid solution was confirmed by the X-ray diffraction patterns. The microwave dielectric properties, such as dielectric constant (?_r), Q × f value and temperature coefficient of resonant frequency (τ_f) have been investigated as a function of composition and sintering temperature. With x increasing from 0.1 to 0.4, the dielectric constant decreases from 70.9 to 43.2, and the τ_f decreases from 105 to 55 ppm/°C. The Q × f value, however, increases with increasing x value to a maximum 26,600 GHz (at 6 GHz) at x = 0.3, and then decreases thereafter. For low-loss microwave applications, a new microwave dielectric material Zr_0.3(Zn_1/3Nb_2/3)_0.7TiO₄, possessing a fine combination of microwave dielectric properties with a high ?_r of 51, a high Q × f of 26,600 GHz (at 6 GHz) and a τ_f of 70 ppm/°C, is suggested.     

Preparation and microwave absorbency of Fe/epoxy and FeNi3/epoxy composites

The focus of this study was placed on the lightness of microwave absorbing effective metal/epoxy composites. For such a focus, high aspect ratio of flake iron powder and high absorbing FeNi₃ were prepared. The iron powder particle size was reduced significantly through wet milling, comparing to dry milling. The FeNi₃ alloy powders were synthesized by mechanical alloying (MA); then, the particle size was reduced through wet milling. The iron powder and FeNi₃ alloy were characterized by scanning electron microscopy (SEM) and X-ray diffraction. SEM of the metal particles showed the flake and small structure by wet milling. The microwave absorbing effectiveness of metal/epoxy composite was affected by the structure, loading and dispersion of metal materials. The polyvinylpyrrolidone (PVP) plays an important role in suspending metal powders in wet milling to reduce powder size. Besides, the PVP will be a coupling agent in inhibiting the aggregation and enhancing the interfacial interaction between metal and epoxy. Results suggested that after the above manufacturing process, the microwave absorbency was enhanced substantially. Composite films of Fe/epoxy and FeNi₃/epoxy 1.6 mm in thickness possessed a microwave absorbency above 10 dB at 9.2-15.2 GHz and 13.1-16.2 GHz, respectively.     

Synthesis of (Bi0.5Na0.5)TiO3 (BNT) and Pr doped BNT using the soft combustion technique and its properties

In this work, bismuth sodium titanate (Bi_0.5Na_0.5)TiO₃ (BNT) and praseodymium (Pr)-doped BNT were successfully produced using the soft combustion technique. The effects of Pr doping on stoichiometry, microstructure, density and dielectric properties were studied. Pure Pr-doped BNT was obtained in all samples containing 5, 10 and 20 mol% Pr after calcination at 800 °C for 3 h. The produced powders were then pressed into pellets and sintered at 1100 °C for 3 h. The very similar ionic radii of Pr³⁺ with Bi³⁺ and Na⁺ made it possible to substitute both Bi and Na. The crystallite size and grain size decreased with increasing Pr amount because Pr acted as grain growth inhibitor, both for calcined powders and for sintered pellets. Maximum density was obtained in 5 mol% Pr-doped BNT, beyond which density decreased. The maximum dielectric constant of 756 was obtained in 5 mol% Pr-doped BNT and decreased at higher levels of Pr doping. Pr doped into BNT also caused a decrease in dielectric loss.     

Low temperature sintering and microwave dielectric properties of (Mg0.7Zn0.3)0.95Co0.05TiO3 ceramics with BaCu(B2O5) additions

The effects of BaCu(B₂O₅) additives on the sintering temperature and microwave dielectric properties of (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were investigated. The (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were not able to be sintered below 1000 °C. However, when BaCu(B₂O₅) were added, they were sintered below 1000 °C and had the good microwave dielectric properties. It was suggested that a liquid phase with the composition of BaCu(B₂O₅) was formed during the sintering and assisted the densification of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics at low temperature. BaCu(B₂O₅) powders were produced and used to reduce the sintering temperature of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics. Good microwave dielectric properties of Q × f = 35,000 GHz, ?_r = 18.5.0 and τ_f = −51 ppm/°C were obtained for the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics containing 7 wt.% mol% BaCu(B₂O₅) sintered at 950 °C for 4 h.     

Microwave dielectric properties of temperature stable Li2ZnxCo1−xTi3O8 ceramics

The Li₂Zn_xCo_1−xTi₃O₈ (x = 0.2-0.8) solid solution system has been synthesized by the conventional solid-state ceramic route and the effect of Zn substitution for Co on microwave dielectric properties of Li₂CoTi₃O₈ ceramics has also been investigated. The microwave dielectric properties of these ceramics show a linear variation between the end members for all compositions. The optimized sintering temperatures of Li₂Zn_xCo_1−xTi₃O₈ ceramics increase with increasing content of Zn. The specimen with x = 0.4 sintered at 1050 °C/2 h exhibits an excellent combination of microwave dielectric properties with ?_r = 27.7, Q_u × f = 57,100 GHz and τ_f = −1.0 ppm/°C.     

Enhanced magnetoelectric properties in Bi0.95Ho0.05FeO3 polycrystalline ceramics

Polycrystalline samples of Ho doped BiFeO₃ were prepared by solid state reaction method and effect of partial substitution of Ho on dielectric, magnetic and ferroelectric properties was studied. High temperature dielectric results show two dielectric anomalies both in ? and tan δ, out of which, anomaly at higher temperature (∼400 °C) could be ascribed to antiferromagnetic Néel temperature which, is a signature of magnetoelectric coupling. The magnetic moment is greatly improved and the maximum magnetization was found to be 0.736 emu/g. Saturated ferroelectric hysteresis loops were observed for Bi_0.95Ho_0.05FeO₃ with remnant polarization (P_r) = 1.59 μC/cm², maximum polarization (P_max) = 2.56 μC/cm² and coercivity (E_c) = 5.45 kV/cm. We have conducted comprehensive magnetoelectric and magnetodielectric properties at room temperature. Magnetic field induced ferroelectric hysteresis loop observed in Bi_0.95Ho_0.05FeO₃ is of prime importance.     

Synthesis and microwave absorbing properties of polyaniline/MnFe2O4 nanocomposite

Conductive polyaniline (PANi)-manganese ferrite (MnFe₂O₄) nanocomposites with core-shell structure were synthesized by in situ polymerization in the presence of dodecyl benzene sulfonic acid (DBSA) as the surfactant and dopant and ammonium persulfate (APS) as the oxidant. The structure and magnetic properties of manganese ferrite nanoparticles were measured by using powder X-ray diffraction (XRD) and vibrating sample magnetometer (VSM), respectively. Its morphology, microstructure and DC conductivity of the nanocomposite were characterized by scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR) and four-wire-technique, respectively. The microwave absorbing properties of the nanocomposite powders dispersing in resin acrylic coating with the coating thickness of 1_.4 mm were investigated by using vector network analyzers in the frequency range of 8-12 GHz. A minimum reflection loss of −15.3 dB was observed at 10.4 GHz.     

Microwave dielectric properties and its compatibility with silver electrode of Li2MgTi3O8 ceramics

The effects of BaCu(B₂O₅) (BCB) additions on the sintering temperature and microwave dielectric properties of Li₂MgTi₃O₈ ceramic have been investigated. The pure Li₂MgTi₃O₈ ceramic shows a relative high sintering temperature (∼1000 °C) and good microwave dielectric properties as Q × f of 40,000 GHz, ?_r of 27.2, τ_f of 2.6 ppm/°C. It was found that the addition of a small amount of BCB can effectively lower the sintering temperature of Li₂MgTi₃O₈ ceramics from 1025 to 900 °C and induce no obvious degradation of the microwave dielectric properties. Typically, the 0.5 wt% BCB added Li₂MgTi₃O₈ ceramic sintered at 900 °C for 2 h exhibited good microwave dielectric properties of Q × f = 36,200 GHz (f = 7.31 GHz), ?_r = 26 and τ_f = −2 ppm/°C. Compatibility with Ag electrode indicates this material can be applied to low temperature-cofired ceramics (LTCC) devices.     

Dielectric and microwave properties of ZrO2 doped CaO-SiO2-B2O3 ceramic matrix composites

The behavior of dielectric and microwave properties against sintering temperature has been carried out on CaO-SiO₂-B₂O₃ ceramic matrix composites with ZrO₂ addition. The results indicated that ZrO₂ addition was advantageous to improve the dielectric and microwave properties. X-ray diffraction (XRD) patterns show that the major crystalline β-CaSiO₃ and a little SiO₂ phase existed at the temperature ranging from 950 °C to 1050 °C. At 0.5 wt% ZrO₂, CaO-SiO₂-B₂O₃ ceramic matrix composites sintered at 1000 °C possess good dielectric properties: ?_r = 5.85, tan δ = 1.59 × 10⁻⁴ (1 MHz) and excellent microwave properties: ?_r = 5.52, Q · f = 28,487 GHz (11.11 GHz). The permittivity of Zr-doped CaO-SiO₂-B₂O₃ ceramic matrix composites exhibited very little temperature dependence, which was less than ±2% over the temperature range of −50 to 150 °C. Moreover, the ZrO₂-doped CaO-SiO₂-B₂O₃ ceramic matrix composites have low permittivity below 5.5 over a wide frequency range from 20 Hz to 1 MHz.     

Low-loss microwave dielectrics using rock salt oxide Li2MgTiO4

Rock-salt-structured Li₂MgTiO₄ ceramic was prepared by the conventional mixed oxide route and its microwave dielectric properties were investigated. The microstructures of the ceramics were characterized by SEM. The dielectric properties of the ceramics exhibited a significant dependence on the sintering condition and crystal structure. A new microwave dielectric material, Li₂MgTiO₄ sintered at 1360 °C has a dielectric constant (?_r) of ∼17.25, a Q × f of ∼97,300 GHz (where f = 9.86 GHz, is the resonant frequency) and a τ_f of ∼-27.2 ppm/°C. The microwave dielectric properties of the ceramic are reported for the first time.     

Crystal structure and microwave dielectric properties of ZnTi(Nb1−xTax)2O8 ceramics

The crystal structure and microwave dielectric properties of ZnTi(Nb_1−xTa_x)₂O₈ (0 ≤ x ≤ 1) ceramics sintered at 1200 °C for 2 h were investigated. For x < 0.5, solid solution phases with the α-PbO₂ structure, typical of ZnTiNb₂O₈, were obtained, whereas for 0.5 ≤ x < 1, mixtures of two solid solutions each respectively based on the α-PbO₂ structure and a trirutile structure, were obtained. The relative amount of the trirutile-structured phases increased as the Ta content increased in a given region, and the end member ZnTiTa₂O₈ formed a single phase with the trirutile structure. The microwave dielectric properties were closely related to the crystal structures. A material with a near zero temperature coefficient of resonant frequency could be obtained for x = 0.8, and its dielectric constant and quality factor (Q × f) were 40.5 and 41,000 GHz, respectively.     

Properties of praseodymium-doped bismuth potassium titanate (Bi0.5K0.5TiO3) synthesised using the soft combustion technique

Bismuth potassium titanate (Bi_0.5K_0.5TiO₃; BKT) and praseodymium-doped BKT (Bi_0.5(1−x)Pr_xK_0.5TiO₃; BPKT) powders were synthesised using the soft combustion technique. Fine particles of 10-100 nm of BKT and BPKT were produced. A single phase BKT was obtained with a minimum of 0.5 mol of glycine. Various compounds of Bi_0.5(1−x)Pr_xK_0.5TiO₃ where x = 0.01, 0.03, 0.05, 0.10, 0.15 and 0.20 were prepared. Pure BKT and BPKT powders were obtained after calcination at 800 °C for 3 h. After sintering at 1050 °C for 5 h, pure BKT and BPKT pellets were obtained for x = 0 and 0.01. However, for BPKT with x = 0.03, 0.05, 0.10, 0.15 and 0.20, a minor amount of Bi₄Ti₃O₁₂ (BIT) secondary phase was present after sintering at 1050 °C for 5 h. The crystallite size and grain size of all the samples followed similar trends, first increasing from x = 0 (undoped BKT) to x = 0.05 and then decreasing above x = 0.05. Among the undoped and doped samples, BPKT with x = 0.05 had the highest dielectric properties (?_r = 713.87) due to its large crystallite size (68.66 nm), large grain size (∼435 nm) and high relative density (93.39%).     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

Characterization of paramagnetic KHo(WO4)2 nanocrystals: Synthesized by polymeric mixed-metal precursor sol-gel method

Nanocrystalline KHo(WO₄)₂ (KHW) particles were successfully synthesized via conventional Pechini sol-gel method. Prepared precursor gel was calcined at 250, 550, 600, 650 and 700 °C, and the resulting samples were analyzed with TG-DTA, powder X-ray diffraction, FT-IR, Raman, FESEM, TEM, UV-Vis-NIR (diffuse reflectance spectrum (DRS)), fluorescence and vibrating sample magnetometer (VSM). Thermal degradation of derived gel was observed up to 400 °C and phase formation starts from 550 °C. The product phase formation at higher annealing temperature was investigated by means of powder XRD. Organic liberation in the samples with respect to temperature was analyzed using FT-IR spectrum. Raman spectrum reveals the formation of tungsten ribbons as well as the quality of the samples while increasing the calcination temperature. The nano size of the synthesized particles was confirmed with FESEM and TEM micrographs. Reflectance and emission studies reveal the corresponding absorption and emission properties of trivalent state holmium ion. Paramagnetic behavior of the derived KHW was confirmed with VSM results.