Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

Mechanical characterization of Ni1−xZnxFe2O4 prepared by non-conventional methods

The mechanical properties like hardness, H_v and compressive strength, σ of Ni_1−xZn_xFe₂O₄ (x = 0.2, 0.3, 0.4 and 0.5) prepared by the non-conventional flash combustion and citrate-gel decomposition techniques are studied and reported. It is observed that there is an increase in hardness with zinc content as well as sintering temperature. The hardness in the order of 2.0–3.63 GPa and compressive strength in the order of 150–240 MPa are obtained for Ni–Zn ferrites prepared by these non-conventional techniques. The influence of density, porosity and microstructure on hardness and compressive strength of Ni–Zn ferrites with respect to sintering temperature was studied.     

Structural and electrochemical characterization of LiMn2−δVδOy spinels

The spinel phase compounds with the composition of LiMn_2−δV_δO_y were prepared by solid reaction of the mixture of LiNO₃·H₂O, MnCO₃ and NH₄VO₃ powders. Evolution of the crystalline phases of the samples versus the vanadium content was analyzed using X-ray diffraction (XRD) technique, EPR and FT-IR spectroscopes. Cubic spinel is the predominant phase in the powders under heat treatment at 550 °C for 5 h. The valence state of manganese ion changed from +4 to +3 with vanadium substitution for charge compensation. The vanadium substitution of manganese leads the decline in capacity and cyclic behavior of the powders. The electrochemical behaviors relating to the variation of structure corresponding to the vanadium substitution were discussed.     

Structural and optical properties of (100 − x)(Li2B4O7) − x(SrO–Bi2O3–0.7Nb2O5–0.3V2O5) glasses and glass nanocrystal composites

Glasses of various compositions in the system (100 − x)(Li₂B₄O₇) − x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (10  x  60, in molar ratio) were prepared by splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as-quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X-ray powder diffraction studies. Glass composites comprising strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) nanocrystallites were obtained by controlled heat-treatment of the as-quenched glasses at 783 K for 6 h. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat-treated at 783 K/6 h) confirm the presence of rod shaped crystallites of SBVN embedded in Li₂B₄O₇ glass matrix. The optical transmission spectra of these glasses and glass nanocrystal composites of various compositions were recorded in the wavelength range 190–900 nm. Various optical parameters such as optical band gap (E_opt), Urbach energy (ΔE), refractive index (n), optical dielectric constant and ratio of carrier concentration to the effective mass (N/m^*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied.     

Interface phenomena in the Y2O3/(Al–Cu) system

Wetting behavior and the interface reaction in the Y₂O₃/(Cu–Al) system were investigated at 1423 K. A contact angle of about 130° was measured in the Y₂O₃/Cu system. Aluminum addition to copper improves wetting and the transition from non-wetting to wetting (θ ≤ 90°) was observed for the alloy with 50 at.% Al. The microstructure examination of the interface indicates that Al reacts with yttria, yttrium dissolves in the melt and a crater of AlYO₃ is formed at the substrate. The interface interaction in the Y₂O₃/(Cu–Al) system is in a good agreement with the results of a thermodynamic analysis in the Y–Al–Cu–O system. The crater depth and the macroscopic final contact angles are correlated with the Y and Al activities in the melt.     

Magnetoimpedance effect at various temperatures for manganite La0.7Ca0.3MnO3−δ

In the present work, the AC magnetoimpedance effect in La_0.7Ca_0.3MnO_3−δ at various temperatures are investigated. The peak of the metal–insulator transition occurs in the temperature dependence of impedance. Negative magnetoimpedance effect in the La_0.7Ca_0.3MnO_3−δ is obtained at frequencies f≤10 MHz. In the magnetoimpedance effect of manganites, the magnetic field not only decreases the permeability μ_t, but also reduces the resistivity ρ by aligning the local spins and varying the transfer integral t_ij. The AC magnetoimpedance participated by the DC colossal magnetoresistance (CMR) in manganites, should be connected with the combined effects of double exchange interaction, electron–phonon coupling and skin effect.     

Dissolution of Y2BaCuO5 through the peritectic reaction rim formed at the front of growing YBa2Cu3O7−y crystal

Microstructure related to the peritectic reaction was investigated in melt-textured Y-Ba-Cu-O. It was found that Y₂BaCuO₅ particles dissolved in the peritectic reaction rim formed at the interface between YBa₂Cu₃O_7−y, crystal and Ba-Cu-O liquid phase. Y₂BaCuO₅ morphology was a blocky shape in the liquid phase while it was changed to a round shape in the textured YBa₂Cu₃O_7−y crystal through an irregular shape due to inhomogeneous dissolution of Y₂BaCuO₅ particles. By way of dissolution, one Y₂BaCuO₅ particle was divided into several particles. The refinement process of Y₂BaCuO₅ is discussed in terms of the dissolution process of Y₂BaCuO₅ and its morphology.     

YNixMn1−xO3 thin films by pulsed laser deposition: Structure and magnetic properties

Highly oriented YNi_xMn_1−xO₃ thin films on SrTiO₃ (100) substrates were achieved by using pulsed laser deposition for x = 0.33 and x = 0.50. We used a combination of X-ray diffraction, scanning electron microscopy, atomic force microscopy, and magnetic-property measurements. The magnetic transition temperatures (T_c) of the as-grown films are higher than the corresponding bulk values (typically 85 K instead of 80 K, for x = 0.5, and 60 K instead of 50 K, for x = 0.33). Our magnetic measurements also suggest a spin-glass characteristic in the x = 0.33 films, while a cluster glasslike behavior is observed for the films with x = 0.5, which is quite different from that of the bulk samples. Finally, the influence of post-deposition heat treatment on the magnetic properties of the as-grown films is discussed.     

Preparation and photoelectrochemical properties of Ti1−xVxO2 solid solution thin film photoelectrodes with gradient bandgap

A design of a gradient bandgap Ti_1−xV_xO₂ thin film electrode for wet-type solar cells is provided. The gradient bandgap film electrodes were prepared by heating stacked layers of varying V/Ti ratios using the sol-gel method. A composition gradient was observed for some of the samples by X-ray photoelectron spectroscopy although it was not very large. For the Ti_1−xV_xO₂ film electrodes, conspicuous visible light photoresponse and photoelectrochemical stability were observed. The photocurrent increased with increasing bias potential. However, the photocurrent onset potentials of the Ti_1−xV_xO₂ film electrodes were more positive than those of TiO₂ film electrodes, probably owing to the high surface state density introduced by the diffusion of vanadium ions.     

In situ co-precipitation synthesis and photoluminescence of YxGd1−xVO4:Tm microcrystalline phosphors by hybrid precursors

Y_xGd_1−xVO₄:Tm³⁺ (5 mol%) phosphors were prepared by in situ co-precipitation technology with the different content ratio of Y/Gd (x = 0.2, 0.3, 0.4, 0.5, 0.6, 0.8, respectively). During the process, rare earth coordination polymers with o-hydroxylbenzoate were used as precursors, composing with polyethylene glycol (PEG) as dispersing media. After heat-treatment of the resulting multicomponent hybrid precursors at 900 °C, the samples were obtained. SEM indicated the particles present good crystalline state, whose crystalline grain sizes were about 0.2–2 μm. Under the excitation of 257 nm, all the materials show the characteristic emission of Tm³⁺ which is the strong blue emission centered at 475 nm originating from ¹G₄ → ³H₆ of Tm³⁺. Besides this, concentration quenching appears in the system of YVO₄:Tm³⁺ and GdVO₄:Tm³⁺. And when x reaches 0.5, the system of Y_xGd_1−xVO₄:Tm³⁺ shows the strongest blue emission.     

Pyroelectric properties of BST/PLT composite thick films with addition of xPbO–(1 − x)B2O3 glass

The Ba_xSr_1−xTiO₃ (BST)/Pb_1−xLa_xTiO₃ (PLT) composite thick films (20 μm) with 12 mol% amount of xPbO–(1 − x)B₂O₃ glass additives (x = 0.2, 0.35, 0.5, 0.65 and 0.8) have been prepared by screen-printing the paste onto the alumina substrates with silver bottom electrode. X-ray diffraction (XRD), scanning electron microscope (SEM) and an impedance analyzer and an electrometer were used to analyze the phase structures, morphologies and dielectric and pyroelectric properties of the composite thick films, respectively. The wetting and infiltration of the liquid phase on the particles results in the densification of the composite thick films sintered at 750 °C. Nice porous structure formed in the composite thick films with xPbO–(1 − x)B₂O₃ glass as the PbO content (x) is 0.5 ≥ x ≥ 0.35, while dense structure formed in these thick films as the PbO content (x) is 0.8 ≥ x ≥ 0.65. The volatilization of the PbO in PLT and the interdiffusion between the PLT and the glass lead to the reduction of the c-axis of the PLT phase. The operating temperature range of our composite thick films is 0–200 °C. At room temperature (20 °C), the BST/PLT composite thick films with 0.35PbO–0.65B₂O₃ glass additives provided low heat capacity and good pyroelectric figure-of-merit because of their porous structure. The pyroelectric coefficient and figure-of-merit F_D are 364 μC/(m² K) and 14.3 μPa^−1/2, respectively. These good pyroelectric properties as well as being able to produce low-cost devices make this kind of thick films a promising candidate for high-performance pyroelectric applications.     

Optical and electrical properties of p-type AgInSnxS2−x (x = 0–0.04) thin films prepared by spray pyrolysis

AgInSn_xS_2−x (x = 0–0.2) polycrystalline thin films were prepared by the spray pyrolysis technique. The samples were deposited on glass substrates at temperatures of 375 and 400 °C from alcoholic solutions comprising silver acetate, indium chloride, thiourea and tin chloride. All deposited films crystallized in the chalcopyrite structure of AgInS₂. A p-type conductivity was detected in the Sn-doped samples deposited at 375 °C, otherwise they are n-type. The optical properties of AgInSn_xS_2−x (x < 0.2) resemble those of chalcopyrite AgInS₂. Low-temperature PL measurements revealed that Sn occupying an S-site could be the responsible defect for the p-type conductivity observed in AgInSn_xS_2−x (x < 2) thin films.     

Dielectric and piezoelectric properties of sol–gel derived Ca doped PbTiO3

Synthesis of Ca doped PbTiO₃ powder by a chemically derived sol–gel process is described. Crystallization characteristics of different compositions Pb_1−xCa_xTiO₃ (PCT) with varying calcium (Ca) content in the range x = 0–0.45 has been investigated by DTA/TGA, X-ray diffraction and scanning electron microscopy. The crystallization temperature is found to decrease with increasing calcium content. X-ray diffraction reveals a tetragonal structure for PCT compositions with x ≤ 0.35, and a cubic structure for x = 0.45. Dielectric properties on sintered ceramics prepared with fine sol–gel derived powders have been measured. The dielectric constant is found to increase with increasing Ca content, and the dielectric loss decreases continuously. Sol–gel derived Pb_1−xCa_xTiO₃ ceramics with x = 0.45 after poling exhibit infinite electromechanical anisotropy (k_t/k_p) with a high d₃₃ = 80 pC/N, ′ = 298 and low dielectric loss (tan δ = 0.0041).     

Effect of PWVA/Sb2O3 complex inhibitor on the corrosion behavior of carbon steel in 55%LiBr solution

The inhibition performance of PWVA/Sb₂O₃ complex inhibitor on carbon steel was studied in 55%LiBr + 0.07 mol L⁻¹ LiOH solution. Results indicated that the complex inhibitor decreased both anodic and cathodic polarization current density and widened the passive potential region of carbon steel in test solution and can be classified as mixed inhibitor. The complex inhibitor exhibited excellent inhibition performance on carbon steel when the concentrations of PWVA and Sb₂O₃ were 300 and 200 mg L⁻¹, respectively. With the solution temperature increasing from 145 to 240 °C, the corrosion rates of carbon steel increased from 4.71 to 120.66 μm y⁻¹. In solution containing the complex inhibitor, the relationship between relative coverage ratio of inhibitor on carbon steel surface and inhibition efficiency at 145 °C was obtained as the equation μ = 0.94η, it was a direct proportion. This result proved that the complex inhibitor inhibited the corrosion of carbon steel by geometric blocking effect. When solution temperature was 160 °C, the adsorption Gibbs free energy of PWVA and Sb₂O₃ on carbon steel were −49.59 and −44.29 kJ mol⁻¹, respectively. It indicated that the adsorption processes of PWVA and Sb₂O₃ on carbon steel surface were spontaneous processes. As a strong oxidant, PWVA facilitated the compact passive film comprising of FeO, Fe₂O₃ and Fe₃O₄ forming on the surface and itself was reduced to heteropoly blue. Sb₂O₃ adsorbed on carbon steel surface formed an adsorption film. PWVA and Sb₂O₃ behaved synergistic effect. The corrosion resistance performance of carbon steel in 55%LiBr + 0.07 mol L⁻¹ LiOH solution was improved by PWVA/Sb₂O₃ complex inhibitor.     

Spectroscopic ellipsometry analysis of GaAs1 − xNx layers grown by molecular beam epitaxy

In this work, we present the effect of nitrogen incorporation on the dielectric function of GaAsN samples, grown by molecular beam epitaxy (MBE) followed by a rapid thermal annealing (for 90 s at 680 °C). The GaAs_1 − xN_x samples with N content up to 1.5% (x = 0.0%, 0.1%, 0.5%, 1.5%), are investigated using room temperature spectroscopic ellipsometry (SE). The optical transitions in the spectral region around 3 eV are analyzed by fitting analytical critical point line shapes to the second derivative of the dielectric function. It was found that the features associated with E₁ and E₁ + Δ₁ transitions are blue-shifted and become less sharp with increasing nitrogen incorporation, in contrast to the case of E₀ transition energy in GaAs_1 − xN_x. An increase of the split-off Δ₁ energy with nitrogen content was also obtained, in agreement to results found with MOVPE GaAs_1 − xN_x grown samples.     

Structure and conducting properties of La0.5Sr0.5CoO3−δ films on YSZ

La_0.5Sr_0.5CoO_3−δ (LSCO) thin films were deposited on yttria stabilized zirconia (YSZ) substrates by pulsed laser deposition (PLD) for application to thin film solid oxide fuel cell electrodes. During the deposition, the substrate temperature was varied from 450 to 750°C, and the oxygen pressure in the chamber was varied from 80 to 310 mTorr. Films deposited at 650°C and an oxygen background pressure of 150 mTorr were mostly (100) oriented. Deposition at higher temperatures or under lower oxygen pressures lead to mostly (110) oriented films. Films with low electrical resistivity of 10⁻³ Ω·cm were obtained.     

High-resolution and analytical transmission electron microscopy of epitaxial YBa2Cu3O7−x thin films and YBa2Cu3O7/PrBa2Cu3O7 superlattices

Transmission electron microscopy (TEM) studies of epitaxial YBa₂Cu₃O_7−x thin films and YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices are summarized. High-resolution imaging of cross-sections and plan views and energy-dispersive X-ray microanalysis and electron energy loss spectroscopy in the transmission electron microscope were the methods applied. In the first section results on YBa₂Cu₃O_7−x thin films With varying oxygen stoichiometry deposited onto SrTiO₃ are discussed. Then, YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices deposited onto SrTiO₃ and MgO are investigated. Finally, an interface analysis of high-quality YBa₂Cu₃O_7−x thin films deposited onto sapphire with yttrium-stabilized zirconia buffer layers is presented.     

Epitaxial grown K1−xRbxTiOPO4 films with extremely flat surfaces for waveguiding

We report on epitaxial {1 0 0} K_1−xRb_xTiOPO₄ waveguide films for the visible spectral range grown on KTiOPO₄ substrates by liquid phase epitaxy. Using the m-line technique a refractive index increase of Δn_x≈0.007 and Δn_z≈0.004 for TM and TE polarisation has been determined for a K_0.78Rb_0.22TiOPO₄ film. Optical transmission and nearfield distribution are comparable to conventional ion-exchanged waveguides. Typical attenuation of about 1 dB/cm for both TM and TE polarisation was obtained at λ=532 and 1064 nm. Energy-dispersive X-ray spectrometry reveals solid-solution films with graded rubidium composition profiles. X-ray rocking curve analyses confirm the epitaxial growth process and indicate perfect and relaxed K_1−xRb_xTiOPO₄ films. Atomic force microscopy investigations reveal regular step structures with step heights Δh<1.3 nm resulting in rms-roughness values of ≈0.4 nm.     

Effect of B-doping on the structural, magnetotransport and magnetocaloric properties of La0.67Ca0.33MnO3 compounds

In this study, the effect of Mn site substitution of B on the structural, electrical and magnetocaloric properties of manganites was investigated. Polycrystalline manganites with the chemical composition La_0.67Ca_0.33Mn_1−xB_xO₃ (x = 0, 0.1, 0.2 and 0.3) were prepared by the standard solid-state process. It was found that the magnetisation, the Curie temperature and the maximum value of the magnetic entropy change |ΔS_m| decrease with increasing concentration of B.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.