Co-Cu-Ce-Fe/γ-Al_2O_3催化剂催化分解N_2O的性能

以等体积浸渍法制备γ-Al_2O_3负载的Co、Cu、Ce和Fe氧化物催化剂,利用正交试验设计实验条件,采用XRD、BET和H_2-TPR等对催化剂进行表征,并考察活性组分对催化剂催化分解N_2O活性的影响。结果表明,催化剂具有尖晶石结构,其BET比表面积随着金属氧化物负载量增加而降低。催化剂中铜的氧化物可以降低还原峰温度,进而明显提高催化活性,Co和Fe的加入对活性有一定的提高,Ce对催化活性没有明显影响。     

动物骨源羟磷灰石负载Co3O4用于N2O催化分解

通过焙烧猪骨和鸡骨获得羟磷灰石(nHAP)载体,并采用浸渍法制备Co3O4/nHAP催化剂。采用XRD、N2物理吸附-脱附、FT-IR和H2-TPR等对催化剂进行表征,在连续流动微反装置上考察催化剂催化分解N2O的性能。结果表明,相比于鸡骨源Co3O4/nHAP催化剂,以猪骨源HAP为载体的催化剂因其较大的比表面积以及较小的Co3O4粒径尺寸,提供了更多的活性位点。特别是猪骨源Co3O4/nHAP催化剂中适量的K、Na等元素促进了Co^3+到Co^2+的还原,削弱了Co-O键,使催化剂的催化活性显著提高。     

负载型钴锰复合金属氧化物催化剂催化分解N_2O

以ZrO_2为载体,采用浸渍法制备负载型钴锰复合金属氧化物催化剂,研究催化剂活性组分负载量、Co与Mn物质的量比、焙烧条件及含H_2O气氛对N_2O转化率的影响。结果表明,催化剂最佳制备条件为:活性组分Co负载质量分数3%,Co与Mn物质的量比为1∶1,焙烧升温速率2℃·min-1,焙烧温度900℃。该条件制备的负载型钴锰复合金属氧化物催化剂在反应温度850℃时,N_2O转化率达98.7%。当反应气氛中H_2O体积分数小于20%条件下,850℃时N_2O转化率高于90%,表明催化剂具有较强的抗水性能。     

M_(0.5)Co_(2.5)O_4(M=La,Ce,Pr,Nd)尖晶石型复合氧化物催化剂催化分解N_2O性能

采用共沉淀法制备了M_(0.5)Co_(2.5)O_4(M=La,Ce,Pr,Nd)钴基尖晶石型复合氧化物催化剂,运用XRD、SEM、H_2-TPR和O_2-TPD-TG等对催化剂物化性能进行表征,并在固定床微型反应器中评价催化剂催化分解N_2O性能。结果表明,稀土金属掺杂改性的钴基尖晶石型复合氧化物催化剂粒径明显减小,比表面积增加,氧化还原性能得到改善,催化分解N_2O活性提高,其中,M_(0.5)Co_(2.5)O_4催化剂催化分解N2O温度低,T10和T95分别为342℃和499℃。     

沉淀方式对沉淀法制备Co_3O_4催化N_2O直接分解性能的影响

以Co(NO_3)_2·6H_2O为钴源,K_2CO_3为沉淀剂,采用沉淀法制备Co_3O_4催化剂,用于催化N_2O直接分解反应。利用N_2~-物理吸附、XRD、FT-IR、TEM、TPR和ICP等对其进行表征,考察沉淀方式对Co_3O_4催化剂结构及其催化性能的影响。结果表明,沉淀方式对制备的Co_3O_4催化剂织构性质、物相组成和晶粒尺寸等影响不大,但显著影响其K残留量和还原性能,进而决定催化剂直接催化分解N_2O的催化性能。反加法制得的催化剂中K残留量为1.43%,明显高于正加法,同时催化剂中Co~(3+)较正加法更易还原,因而表现出更高的催化性能。在空速10 000 h~(-1)和N_2O体积分数0.1%的条件下,反加法制备的催化剂可在280℃催化N_2O完全分解,较正加法低20℃。     

新型Cu-Mn/TiO_2和Cu-Mn/γ-Al_2O_3甲醛催化氧化催化剂的研制及活性

采用浸渍法制备了Cu-Mn/γ-Al2O3、Cu-Mn/Ti O2新型催化剂,研究了在不同温度、不同气体流速下对甲醛的催化活性以及50h下催化剂的稳定性,并与Cu-Mn复合氧化物催化剂进行对比。结果表明:γ-Al2O3、Ti O2与Cu-Mn之间的协同作用提高了催化剂对甲醛的催化活性,且Cu-Mn/γ-Al2O3在150℃可以实现甲醛的完全去除,比Cu-Mn/Ti O2和Cu-Mn复合氧化物催化剂分别低80℃和140℃。3种催化剂的甲醛去除率随气速的增加而下降,且变化大小顺序为Cu-Mn/Ti O2Cu-Mn/γ-Al2O3Cu-Mn复合氧化物。50h后Cu-Mn/γ-Al2O3和Cu-Mn复合氧化物催化剂去除率仍为100%,Cu-Mn/Ti O2去除率在94%以上。采用XRD、BET和SEM-EDS等技术手段对制备的Cu-Mn/Ti O2、Cu-Mn/γ-Al2O3和Cu-Mn复合氧化物进行了表征。     

利用Fluent软件对N_2O催化分解反应器数值模拟

为了设计N_2O催化分解反应器,运用Fluent软件对整体式分子筛催化剂进行数值模拟,考察孔密度和操作条件对整体式分子筛催化剂转化率的影响。结果表明,在相同温度下,N_2O的转化率随着催化剂孔密度的减小而降低。在反应器轴向距离120 mm处,气体反应最快;提高入口温度、浓度或降低空速,均有利于在较短的轴向距离内达到较高的N_2O转化率。在固定床反应器中,比较棒状催化剂和整体式催化剂中床层温度、反应转化率及轴向压降的变化规律,为整体式分子筛催化剂工业化设计提供理论基础。     

单分散Co3O4@SiO2核壳催化剂的制备及N2O催化分解性能

N₂O是一种重要的温室气体,且对臭氧层有很大的破坏作用,而直接催化分解法是除去N₂O最经济有效的方法之一。针对目前报道较多的钴氧化物催化剂活性较差的问题,将包覆型Co₃O₄核壳材料引入N₂O直接催化分解反应,利用核壳结构的限域特性与壳层的多孔孔道使Co₃O₄分散性增加,粒径减小,金属载体相互作用与接触反应界面增强,从而提高了催化剂在N₂O直接催化分解反应中的低温活性。此外,还制备了一系列不同金属含量的Co₃O₄@SiO₂球形核壳催化剂来研究包覆结构对催化剂性能的影响,通过X射线荧光光谱（XRF）、透射电镜（TEM）、X射线衍射（XRD）、N₂物理吸附、H₂-程序升温还原（H₂-TPR）等表征,证实在保证稳定单分散核壳结构的前提下,活性Co₃O₄位点越多,催化剂反应活性越好。     

Co3O4-MMT催化剂的制备及其N2O催化分解性能

以MMT为载体,采用原位聚合-配位沉积法制备3种不同Co负载量的Co₃O₄-MMT催化剂。采用N₂物理吸附、XRD和TEM对载体和催化剂进行表征,并在连续流动微反装置上考察其N₂O催化分解性能。结果表明,与Co₃O₄催化剂相比,Co₃O₄-MMT催化剂的比表面积显著增大,且活性组分Co₃O₄具有较高的分散状态。Co₃O₄-MMT催化剂的催化活性随着Co含量的增加先升后降,其中0.015Co-MMT表现出最佳的催化活性,其活性远高于Co₃O₄催化剂,同时,该催化剂还表现出良好的催化稳定性和较好的杂质气体耐受性。     

Fe/beta分子筛催化N2O分解

通过液相离子交换法对H-beta分子筛进行改性得到Fe/beta分子筛,并应用于催化N2O直接分解反应,考察加入HNO3后的体系pH值对Fe/beta催化性能的影响。采用N2物理吸附-脱附、XRD、IR、DR UV-Vis、NH3-TPD和ICP-OES等对Fe/beta分子筛进行分析表征。结果表明,溶液pH值降低过程中催化剂的结晶度、比表面积、孔容及Fe3+含量呈现先增加后减少。溶液pH为2.0时所制备的Fe/beta分子筛催化N2O完全分解温度明显低于pH为2.6和1.0时制备的Fe/beta催化剂,显示了较好的催化活性。     

负载型RuO_2/Me_xO_y(Me=La,Mg,Al)催化剂催化分解N_2O

采用共沉淀法制备LaMgAlO(简称Me_xO_y)复合金属氧化物,以Me-xO_y为载体,采用浸渍法制备系列负载型RuO_2/Me_xO_y催化剂,应用BET、TEM、XRF和SEM对代表性样品进行表征。结果表明,实验条件下,RuO_2负载质量分数2.0%时比较合适,在气体混合物中含有氧和少量水蒸汽条件下,催化剂具有较好的催化分解N_2O稳定性。     

N2O catalytic decomposition over various spinel-type oxides

Various spinel-type catalysts AB₂O₄ (where A = Mg, Ca, Mn, Co, Ni, Cu, Cr, Fe, Zn and B = Cr, Fe, Co) were prepared and characterized by XRD, BET, TEM and FESEM-EDS. The performance of these catalysts towards the decomposition of N₂O to N₂ and O₂ was evaluated in a temperature programmed reaction (TPR) apparatus in the absence and the presence of oxygen. Spinel-type oxides containing Co at the B site were found to provide the best activity. The half conversion temperature of nitrous oxide over the MgCo₂O₄ catalyst was 440 °C and 470 °C in the absence and presence of oxygen, respectively (GHSV = 80,000 h⁻¹).

On the grounds of temperature programmed oxygen desorption (TPD) analyses as well as of reactive runs, the prevalent activity of the MgCo₂O₄ catalyst could be explained by its higher concentration of suprafacial, weakly chemisorbed oxygen species, whose related vacancies contribute actively to nitrous oxide catalytic decomposition. This indicates the way for the development of new, more active catalysts, possibly capable of delivering at low temperatures amounts of these oxygen species even higher than those characteristic of MgCo₂O₄.     

Catalytic decomposition of N2O over CeO2 promoted Co3O4 spinel catalyst

A series of CeO₂ promoted cobalt spinel catalysts were prepared by the co-precipitation method and tested for the decomposition of nitrous oxide (N₂O). Addition of CeO₂ to Co₃O₄ led to an improvement in the catalytic activity for N₂O decomposition. The catalyst was most active when the molar ratio of Ce/Co was around 0.05. Complete N₂O conversion could be attained over the CoCe0.05 catalyst below 400 °C even in the presence of O₂, H₂O or NO. Methods of XRD, FE-SEM, BET, XPS, H₂-TPR and O₂-TPD were used to characterize these catalysts. The analytical results indicated that the addition of CeO₂ could increase the surface area of Co₃O₄, and then improve the reduction of Co³⁺ to Co²⁺ by facilitating the desorption of adsorbed oxygen species, which is the rate-determining step of the N₂O decomposition over cobalt spinel catalyst. We conclude that these effects, caused by the addition of CeO₂, are responsible for the enhancement of catalytic activity of Co₃O₄.     

N2O decomposition over wet- and solid-exchanged Fe-ZSM-5 catalysts

The N₂O decomposition activity of Fe-ZSM-5 strongly depends on the iron content and the preparation methods, including wet (WIE) and solid state ion exchanges (SSIE). The state of Fe species formed on the surface of a series of Fe-ZSM-5 catalysts containing a variety of Fe contents with respect to the preparation method and their role for N₂O decomposition activity have been systematically examined. The general trend for the decomposition activity of Fe-ZSM-5-SSIE is higher than that of Fe-ZSM-5-WIE, indicating the formation of a distinctive local structure of Fe on the catalyst surface during the course of the ion-exchange procedure. Based upon the Fourier transformed Fe K-edge EXAFS spectra for the series of Fe-ZSM-5-SSIE and -WIE catalysts, most of the Fe species on the surface of Fe-ZSM-5-SSIE with high Fe loading are well dispersed in the form of oxygen-bridged binuclear Fe species. The turnover frequency (TOF) for N₂O decomposition under dry and wet conditions has been confirmed assuming that Fe-ZSM-5-SSIE samples with Fe/Al = 0.20 and Fe/Al = 0.65 only contain mononuclear and binuclear Fe species, respectively, as active reaction species on their surface. The high performance of Fe-ZSM-5-SSIE may be mainly due to the formation of the binuclear Fe species onto its surface during the preparation of the catalyst.     

分子筛催化剂上N2O催化分解的研究进展

氧化亚氮(N2O)会造成温室效应和臭氧层破坏,N2O的控制日益引起关注。催化分解技术是控制N2O的有效手段,分别对Fe基、Cu基和Co基分子筛催化剂催化分解N2O的研究现状进行总结和评述,并展望未来发展方向。     

Superior performance of Ir-substituted hexaaluminate catalysts for N2O decomposition

Novel Ir-substituted hexaaluminate catalysts were developed for the first time and used for catalytic decomposition of high concentration of N₂O. The catalysts were prepared by one-pot precipitation and characterized by X-ray diffraction (XRD), N₂-adsorption, scanning electronic microscopy (SEM) and temperature-programmed reduction (H₂-TPR). The XRD results showed that only a limited amount of iridium was incorporated into the hexaaluminate lattice by substituting Al³⁺ to form BaIr_xFe_1−xAl₁₁O₁₉ after being calcined at 1200 °C, while the other part of iridium existed as IrO₂ phase. The activity tests for high concentration (30%, v/v) of N₂O decomposition demonstrated that the BaIr_xFe_1−xAl₁₁O₁₉ hexaaluminates exhibited much higher activities and stabilities than the Ir/Al₂O₃-1200, and the pre-reduction with H₂ was essential for activating the catalysts. By comparing BaIr_xFe_1−xAl₁₁O₁₉ with BaIr_xAl_12−xO₁₉ (x = 0–0.8), it was found that iridium was the active component in the N₂O decomposition and the framework iridium was more active than the large IrO₂ particles. On the other hand, Fe facilitated the formation of hexaaluminate as well as the incorporation of iridium into the framework.     

Catalytic decomposition of N2O over supported Rh catalysts: effects of supports and Rh dispersion

The study of catalytic decomposition of nitrous oxide to nitrogen and oxygen over Rh catalysts supported on various supports (USY, NaY, Al₂O₃, ZrO₂, FSM-16, CeO₂, La₂O₃) showed that the activities of Rh/Al₂O₃ and Rh/USY (ultrastable Y zeolite) catalysts were comparable to or higher than the other catalysts reported in the literatures. The catalytic activity of N₂O decomposition was sensitive not only to the Rh dispersion but also to the preparation variables such as the Rh precursors and the supports used. A pulsed N₂O experiment over a Rh/USY catalyst suggested that the catalytic N₂O decomposition occurs on oxygen-covered surface and that O₂ may be freed on collision of N₂O molecules with the adsorbed oxygen atoms.