Helium ion microscopy for high-resolution visualization of the articular cartilage collagen network

The articular cartilage collagen network is an important research focus because network disruption results in cartilage degeneration and patient disability. The recently introduced helium ion microscope (HIM), with its smaller probe size, longer depth of field and charge neutralization, has the potential to overcome the inherent limitations of electron microscopy for visualization of collagen network features, particularly at the nanoscale. In this study, we evaluated the capabilities of the helium ion microscope for high-resolution visualization of the articular cartilage collagen network. Images of rabbit knee cartilage were acquired with a helium ion microscope; comparison images were acquired with a field emission scanning electron microscope (FE-SEM) and a transmission electron microscope (TEM). Sharpness of example high-resolution helium ion microscope and field emission scanning electron microscope images was quantified using the 25-75% rise distance metric. The helium ion microscope was able to acquire high-resolution images with unprecedented clarity, with greater sharpness and three-dimensional-like detail of nanoscale fibril morphologies and fibril connections, in samples without conductive coatings. These nanoscale features could not be resolved by field emission scanning electron microscopy, and three-dimensional network structure could not be visualized with transmission electron microscopy. The nanoscale three-dimensional-like visualization capabilities of the helium ion microscope will enable new avenues of investigation in cartilage collagen network research.     

Anisotropic properties of bovine nasal cartilage

To investigate the structural anisotropy in bovine septal cartilage, quantitative procedures in microscopic magnetic resonance imaging (μMRI), polarized light microscopy (PLM), and mechanical indentation were used to measure the tissue in three orthogonal planes: vertical, medial, and caudocephalic. The quantitative T2 imaging experiments in μMRI found strong anisotropy in the images of both vertical and caudocephalic planes but little anisotropy in the images from the medial plane. The PLM birefringent experiments found that the retardation values in the medial section were only about 10% of these in the vertical and caudocephalic sections and that the angle values in all three sections followed the rotation of the tissue section in the microscope stage. The stress relaxation experiments in mechanical indentation showed reduced stiffness in the medial plane compared to stiffness in either the vertical or caudocephalic planes. Collectively, the results in this project coherently indicate a marked structural anisotropy in cartilage from the nasal septum, where the long axis of the collagen fibrils is oriented in parallel with the medial axis.     

Influence of anti-inflammatory administration in collagen maturation process during orthodontic tooth movement

Bone formation is essential to orthodontic tooth movement and bone is formed by collagen. To analyze the collagen maturation process on bone matrix neoformed under nonsteroidal and steroidal treatment during orthodontic tooth movement by polarized microscopy, male Wistar rats (n = 90) were randomly divided into three groups (n = 30): C (control), NSAID (potassium diclofenac) and SAID (disodic phosphate dexamethasone). The animals of the C group received 0.9% saline solution; NSAID group received 5 mg/kg potassium diclofenac (CATAFLAM®); and SAID group received 2 mg/kg phosphate dissodic dexamethasone (DEXANIL®). Animals were sacrificed 3, 7 or 14 days after the placement of orthodontic appliances and the upper first molars were processed histologically and stained with picrosirius. Bone formation was evaluated under polarized light microscopy and 4.5 Image Pro‐Plus® software calculated the percentage of immature/mature collagen present in the groups. On the third days after force application, SAID and NSAID groups showed greater proportion of immature collagen than C group. On the seventh and fourteenth days, there was a lower proportion of mature collagen only in the SAID group (P < 0.001). These data demonstrate that dexamethasone delays the collagen maturation process in established bone matrix. Microsc. Res. Tech., 2011. © 2010 Wiley‐Liss, Inc.     

Differentiating the extent of cartilage repair in rabbit ears using nonlinear optical microscopy

Nonlinear optical microscopy (NLOM) was used as a noninvasive and label‐free tool to detect and quantify the extent of the cartilage recovery. Two cartilage injury models were established in the outer ears of rabbits that created a different extent of cartilage recovery based on the presence or absence of the perichondrium. High‐resolution NLOM images were used to measure cartilage repair, specifically through spectral analysis and image texture. In contrast to a wound lacking a perichondrium, wounds with intact perichondria demonstrated significantly larger TPEF signals from cells and matrix, coarser texture indicating the more deposition of type I collagen. Spectral analysis of cells and matrix can reveal the matrix properties and cell growth. In addition, texture analysis of NLOM images showed significant differences in the distribution of cells and matrix of repaired tissues with or without perichondrium. Specifically, the decay length of autocorrelation coefficient based on TPEF images is 11.2 ± 1.1 in Wound 2 (with perichondrium) and 7.5 ± 2.0 in Wound 1 (without perichondrium), indicating coarser image texture and faster growth of cells in repaired tissues with perichondrium (p < 0.05). Moreover, the decay length of autocorrelation coefficient based on collagen SHG images also showed significant difference between Wound 2 and 1 (16.2 ± 1.2 vs. 12.2 ± 2.1, p < 0.05), indicating coarser image texture and faster deposition of collagen in repaired tissues with perichondrium (Wound 2). These findings suggest that NLOM is an ideal tool for studying cartilage repair, with potential applications in clinical medicine. NLOM can capture macromolecular details and distinguish between different extents of cartilage repair without the need for labelling agents.     

Immunohistochemical analysis of structural changes in collagen for the assessment of osteoarthritis

Collagen fibrillation within articular cartilage (AC) plays a key role in joint osteoarthritis (OA) progression and, therefore, studying collagen synthesis changes could be an indicator for use in the assessment of OA. Various staining techniques have been developed and used to determine the collagen network transformation under microscopy. However, because collagen and proteoglycan coexist and have the same index of refraction, conventional methods for specific visualization of collagen tissue is difficult. This study aimed to develop an advanced staining technique to distinguish collagen from proteoglycan and to determine its evolution in relation to OA progression using optical and laser scanning confocal microscopy (LSCM). A number of AC samples were obtained from sheep joints, including both healthy and abnormal joints with OA grades 1 to 3. The samples were stained using two different trichrome methods and immunohistochemistry (IHC) to stain both colourimetrically and with fluorescence. Using optical microscopy and LSCM, the present authors demonstrated that the IHC technique stains collagens only, allowing the collagen network to be separated and directly investigated. Fluorescently-stained IHC samples were also subjected to LSCM to obtain three-dimensional images of the collagen fibres. Changes in the collagen fibres were then correlated with the grade of OA in tissue. This study is the first to successfully utilize the IHC staining technique in conjunction with laser scanning confocal microscopy. This is a valuable tool for assessing changes to articular cartilage in OA.     

The interface region between articular cartilage and bone by μMRI and PLM at microscopic resolutions

This dual-modality microscopic imaging study quantifies the interface region between the noncalcified cartilage and the subchondral bone plate, which includes the deep portion of the noncalcified articular cartilage and the zone of calcified cartilage (ZCC). This interface region is typically not visible in routine MRI but becomes visible in MRI with the application of an ultra-short echo time (UTE) sequence. A number of cartilage-bone blocks from a well-documented canine humeral head were harvested for imaging by microscopic MRI (μMRI) and PLM (polarized light microscopy). In μMRI, T2 anisotropic images were acquired by 2D gradient-echo, magnetization-prepared spin-echo and UTE sequences at the 0° and 55° (the magic angle) orientations at 11.7 μm/pixel resolution. In PLM, quantitative optical retardation (nm) and collagen orientation (°) were mapped from the thin sections from the same μMRI specimens at 0.5–2 μm pixel resolutions. The orientational and organizational architecture of the collagen matrix in this interface region was quantified and correlated between the complementary imaging. The magic angle effect as seen in the noncalcified cartilage was statistically confirmed in ZCC in μMRI, which was further supported by quantitative PLM. With an enhanced understanding of the tissue properties in this important interface region, it will potentially be possible to monitor the changes of this tissue region which is instrumental to the initiation and development of osteoarthritis and other joint diseases.     

Comparative evaluation of vegetable matter involved lesions with oral parasitic infections in the oral cavity

The current research aims to perform a comparative evaluation of vegetable matter involved lesions with oral parasitic infections found in oral mucosa, presenting histochemical methods to differentiate their microscopic similarities. Eight cases were selected out of a sample of 1.975 reports from a single Oral and Maxillofacial Pathology Service of the author's institution from 2012 to 2019. Specimens were examined by hematoxylin and eosin staining (HE), periodic acid-Schiff (PAS) staining, Gomori–Grocott staining, Ziehl–Neelsen staining, Giemsa, and mucicarmine staining. Microscopic analysis included fluorescence, polarized light, and confocal microscopy. Microscopically, in HE coloration, hookworm eggs showed as eosinophilic. Inflammatory multinucleated giant cells and lymphocytes, were usually related to the nematode eggs, forming an intense inflammatory infiltrate. Biofluorescent properties of eggs and larvae revealed to be sensitive in the detection of parasitic structures contrasting with the inflamed connective tissue. Vegetable presence was confirmed by polarized light microscopy and it was found to be associated with microbial biofilms. Confocal microscopy has showed to be an excellent method for morphotype differentiation of parasitic eggs. Parasitic infection and vegetable matter displayed similarities in the inflammatory response, but the latter can rot and agglomerate biofilms. The microscopic diagnosis of such infections requires the interpretation of challenging morphological features since the parasites are usually sectioned and mixed with an inflammatory reaction. These histochemical approaches proved to be excellent to distinguish both lesions.     

The application of heat‐deproteinization to the morphological study of cortical bone: A contribution to the knowledge of the osteonal structure

Observation of heat‐deproteinized cortical bone specimens in incident light enabled the high definition documentation of the osteonal pattern of diaphyseal Haversian bone. This prompted a study to compare these images with those revealed by polarized light microscopy, carried out either on decalcified or thin, undecalcified, resin‐embedded sections. Different bone processing methods can reveal structural aspects of the intercellular matrix, depending on the light diffraction mode: birefringency in decalcified sections can be ascribed to the collagen fibrils orientation alone; in undecalcified sections, to both the ordered layout of collagen and the inorganic phase; in the heat‐deproteinized samples, exclusively to the hydroxyapatite crystals aggregation mode. The elemental chemical analysis documented low content of carbon and hydrogen, no detectable levels of nitrogen and significantly higher content of calcium and phosphorus in heat‐deproteinized samples, as compared with dehydrated controls. In both samples, the X‐ray diffraction (XRD) pattern did not show any significant difference in pattern of hydroxyapatite, with no peaks of any possible decomposition phases. Scanning electron microscopic (SEM) morphology of heat‐deproteinized samples could be documented with the fracturing technique facilitated by the bone brittleness. The structure of crystal aggregates, oriented in parallel and with marks of time periods, was documented. Comparative study of deproteinized and undecalcified samples showed that the matrix inorganic phase did not undergo a coarse grain thermal conversion until it reached 500°C, maintaining the original crystals structure and orientation. Incident light stereomicroscopy, combined with SEM analysis of deproteinized bone fractured surfaces, is a new enforceable technique which can be used in morphometric studies to improve the understanding of the osteonal dynamics. Microsc. Res. Tech. 79:691–699, 2016. © 2016 Wiley Periodicals, Inc.     

Comparative measurement of collagen bundle orientation by Fourier analysis and semiquantitative evaluation: reliability and agreement in Masson's trichrome,Picrosirius red and confocal microscopy techniques

Measurement of collagen bundle orientation in histopathological samples is a widely used and useful technique in many research and clinical scenarios. Fourier analysis is the preferred method for performing this measurement, but the most appropriate staining and microscopy technique remains unclear. Some authors advocate the use of Haematoxylin‐Eosin (H&E) and confocal microscopy, but there are no studies comparing this technique with other classical collagen stainings. In our study, 46 human skin samples were collected, processed for histological analysis and stained with Masson's trichrome, Picrosirius red and H&E. Five microphotographs of the reticular dermis were taken with a 200× magnification with light microscopy, polarized microscopy and confocal microscopy, respectively. Two independent observers measured collagen bundle orientation with semiautomated Fourier analysis with the Image‐Pro Plus 7.0 software and three independent observers performed a semiquantitative evaluation of the same parameter. The average orientation for each case was calculated with the values of the five pictures. We analyzed the interrater reliability, the consistency between Fourier analysis and average semiquantitative evaluation and the consistency between measurements in Masson's trichrome, Picrosirius red and H&E‐confocal. Statistical analysis for reliability and agreement was performed with the SPSS 22.0 software and consisted of intraclass correlation coefficient (ICC), Bland‐Altman plots and limits of agreement and coefficient of variation. Interrater reliability was almost perfect (ICC > 0.8) with all three histological and microscopy techniques and always superior in Fourier analysis than in average semiquantitative evaluation. Measurements were consistent between Fourier analysis by one observer and average semiquantitative evaluation by three observers, with an almost perfect agreement with Masson's trichrome and Picrosirius red techniques (ICC > 0.8) and a strong agreement with H&E‐confocal (0.7 < ICC < 0.8). Comparison of measurements between the three techniques for the same observer showed an almost perfect agreement (ICC > 0.8), better with Fourier analysis than with semiquantitative evaluation (single and average). These results in nonpathological skin samples were also confirmed in a preliminary analysis in eight scleroderma skin samples. Our results show that Masson's trichrome and Picrosirius red are consistent with H&E‐confocal for measuring collagen bundle orientation in histological samples and could thus be used indistinctly for this purpose. Fourier analysis is superior to average semiquantitative evaluation and should keep being used as the preferred method.     

Quantification of the graphical details of collagen fibrils in transmission electron micrographs

A novel 2D image analysis technique is demonstrated. Using the digitized images of articular cartilage from transmission electron microscopy (TEM), this technique performs a localized 'vector' analysis at each region that is large enough to include several or tens of collagen fibrils but small enough to provide a fine resolution for the whole tissue. For each small and localized region, the morphology of the collagen fibrils can be characterized by three quantities essential to the nature of the tissue: the concentration of the fibrils, the overall orientation of the fibrils, and the anisotropy of the fibrils. This technique is capable of providing new insight to the existing technology by assigning quantitative attributes to the qualitative graphics. The assigned quantities are sensitive to the fine structure of the collagen matrix and meaningful in the architectural nature of the collagen matrix. These quantities could provide a critical linkage between the ultrastructure of the tissue and the macroscopic behaviours of the material. In addition, coarse-graining the microscopic resolution of EM without compromising the essential features of the tissue's structure provides a direct view of the tissue's morphology and permits direct correlations and comparisons among interdisciplinary techniques.     

Correlation between friction of articular cartilage and reflectance intensity from superficial images

The lubrication mechanism of articular cartilage is characterized by an efficient performance. In this work, friction of articular cartilage was evaluated with in-site images of articular surface. The images were captured with the laser light reflected at the interface between a prism and articular cartilage. The attenuation of reflectance was associated with the increase of the contact of collagen network of articular cartilage. The light reflectance and friction coefficient for short sliding presented a significant positive correlation. Friction tests were also carried out for short (30 s) and long (300 s) preloading times. The results indicate that depletion of fluid film is responsible for the increase of friction and the recovery of the fluid film was observed for the long preloading after the early stage of sliding.     

Structural arrangement of the cardiac collagen fibers of healthy and diabetic dogs

The heart is composed by a specialized muscle, whose form and function are essentials for an adequate work and shows an amount of connective tissue which support and provide insertion for this muscle, whose collagen fibers are responsible for determination of tissue feature. Our objective was to identify the structural arrangement of the heart collagen fibers in dogs. The hearts of the dogs were submitted to the process of the controlled digestion with NaOH solution and observed by scanning electron microscope. Our results showed that the collagen fibers of the endomysial wall have structural arrangement composed by an irregular network with one layer in normal dogs but in diabetic dogs the network acquires a greater amount of the fibers and layers, looking like a "rug" of fibers modifying the relationships of the stress/strain of the tissue. Ahead of the observed results we are able to conclude that exist increase in the amount and thickness of cardiac collagen fibers, beyond the increase of layers and architectural disarrangement in the endomysial wall in the diabetic dogs.     

Analysis of biphasic lubrication of articular cartilage loaded by cylindrical indenter

Combination of theoretical biphasic analyses and corresponding experimental measurements for articular cartilage has successfully revealed the fundamental material properties and time-depending mechanical behaviors of articular cartilage containing plenty of water. The insight of load partitioning between solid and fluid phases advanced the prediction of the frictional behavior of articular cartilage. One of the recent concerns about biphasic finite element (FE) analysis seems to be a dynamic and physiological condition in terms of mechanical functionality as a load-bearing for articular joint system beyond material testing, which has mainly focused on time-dependent reaction force and deformation in relatively small and low speed compression. Recently, the biphasic FE model for reciprocating sliding motion was applied to confirm the frictional effect on the migrating contact area. The results indicated that the model of a cylindrical indenter sliding over the cartilage surface remarkably sustained the higher proportion of fluid load support than a condition without migrating contact area, but the effectiveness of constitutive material properties has not been sufficiently evaluated for sliding motion. In our present study, at the first stage, the compressive response of the articular cartilage was examined by high precision testing machine. Material properties for the biphasic FE model, which included inhomogeneous apparent Young's modulus of solid phase along depth, strain-dependent permeability and collagen reinforcement in tensile strain, were estimated in cylindrical indentation tests by the curve fitting between the experimental time-dependent behavior and FE model simulation. Then, the biphasic lubrication mechanism of the articular cartilage including migrating contact area was simulated to elucidate functionality as a load-bearing material. The results showed that the compaction effect on permeability of solid phase was functional particularly in the condition without the migrating contact area, whereas in sliding condition the compaction effect did not clearly show its role in terms of the proportion of fluid load support. The reinforcement of solid phase, which represented the collagen network in the tissue, improved the proportion of fluid load support especially in the sliding condition. Thus, a functional integration of constitutive mechanical properties as a load-bearing was evaluated by FE model simulation in this study.     

Confocal scanning optical microscopy of a 3‐million‐year‐old Australopithecus afarensis femur

Portable confocal scanning optical microscopy (PCSOM) has been specifically developed for the noncontact and nondestructive imaging of early human fossil hard tissues, which here we describe and apply to a 3‐million‐year‐old femur from the celebrated Ethiopian skeleton, “Lucy,” referred to Australopithecus afarensis. We examine two bone tissue parameters that demonstrate the potential of this technology. First, subsurface reflection images from intact bone reveal bone cell spaces, the osteocyte lacunae, whose density is demonstrated to scale negatively with body size, reflecting aspects of metabolism and organismal life history. Second, images of a naturally fractured cross section near to Lucy's femoral mid‐shaft, which match in sign those of transmitted circularly polarized light, reveal relative collagen fiber orientation patterns that are an important indicator of femoral biomechanical efficacy. Preliminary results indicate that Lucy was characterized by metabolic constraints typical for a primate her body size and that in her femur she was adapted to habitual bipedalism. Limitations imposed by the transport and invasive histology of unique or rare fossils motivated development of the PCSOM so that specimens may be examined wherever and whenever nondestructive imaging is required. SCANNING 31: 1–10, 2009. © 2009 Wiley Periodicals, Inc.     

Extracellular matrix of ostrich articular cartilage.

The composition and organization of the extracellular matrix of ostrich articular cartilage was investigated, using samples from the proximal and distal surfaces of the tarsometatarsus. For morphological analysis, sections were stained with toluidine blue and analyzed by polarized light microscopy. For biochemical analysis, extracellular matrix components were extracted with 4 M guanidinium chloride, fractionated on DEAE-Sephacel and analyzed by SDS-PAGE. Glycosaminoglycans were analyzed by electrophoresis in agarose gels. Structural analysis showed that the fibrils were arranged in different directions, especially on the distal surface. The protein and glycosaminoglycan contents of this region were higher than in the other regions. SDS-PAGE showed the presence of proteins with molecular masses ranging from 17 to 121 kDa and polydisperse components of 67, 80-100, and 250-300 kDa in all regions. The analysis of glycosaminoglycans in agarose-propylene diamine gels revealed the presence of only chondroitin-sulfate. The electrophoretic band corresponding to putative decorin was a small proteoglycan containing chondroitin-sufate and not dermatan-sulfate, unlike other cartilages. The higher amounts of proteins and glycosaminoglycans and the multidirectional arrangement of fibrils seen in the distal region may be correlated with the higher compression normally exerted on this region.     

Influence of pitch air-blowing and thermal treatment on the microstructure and mechanical properties of carbon/carbon composites

This paper discusses the optimization of pitch properties as a matrix precursor of C/C composites by subjecting the pitches to different pretreatments to promote polymerization of the molecular components of pitch, which could improve carbon yield and density of the resultant carbon materials. Two series of pitches were prepared by air-blowing of impregnating coal-tar pitches at temperatures between 523 and 573 K, and thermal treatment at temperatures between 673 and 703 K, in an inert atmosphere. Effects of pitch treatments on resultant coke texture and porosity were monitored by polarized light microscopy. Unidirectional laminar composites were prepared using the original and treated pitches and commercial PAN-based carbon fibres. Effects of pitch treatments on the main microstructural features of composites are determined by scanning electron microscopy and polarized light microscopy, and related to the mechanical properties of composites. Results show an improvement of the mechanical properties of composites in both series, particularly for pitch treatments at 523 K/air in the air-blown series, and at 698 K–5 h in the thermally treated one.     

Second Harmonic Generation in 3‐D Uniform Arrangement of Type I Collagen on Nonlinear Optics Microscopy

Second harmonic microscopic imaging and spectroscopy technology has become a powerful tool for biomedical studies, especially in fibrosis‐related diseases research. And type I collagen is the major risk factors for fibrotic diseases. In this study, model for three‐dimensional (3‐D) uniform arrangement type I collagen is set up for researching the second harmonic generation (SHG) on nonlinear optics microscopy. Based on this model, we discuss the influence of different length and size collagen in 3‐D arrangement type I collagen. Results can guide us to neatly judge the size, length, and molecules density effect on SHG. For practical application, this theoretical approach can lead us to analyze different severity of collagen diseases. SCANNING 35:12‐16, 2013. © 2012 Wiley Periodicals, Inc.     

Visualization of the nanoscale assembly of type I collagen on PLA by AFM

Collagen adsorption and the morphology of its assemblies at polymer surface play an important role in improving the biocompatibility of materials. In this study, the nanoscale organization of type I collagen on Polylactide (PLA) was observed directly by high‐resolution atomic force microscopy. The results show that the supramolecular structure of adsorbed collagen was affected by the concentration of collagen solution, appropriate pH and electrolyte composition of the buffer. On PLA substrate, network structures formed in high humidity atmosphere. In addition, collagen formed well‐oriented nano‐patterns at nearly neutral pH and appropriate electrolyte composition. Particularly, the typical 65 nm D‐periodicity of collagen fibers was observed in the presence of potassium ions. Our investigation provides useful insights into the regulation of collagen assembly by substrates and environmental conditions, which is important for understanding the mechanism of collagen adsorption and assembly on polymer surfaces. It also offers a potential way to create surfaces of bio‐functioned and nano‐patterned materials for biotechnological and biomedical applications. SCANNING 32: 104–111, 2010. © 2010 Wiley Periodicals, Inc.