High aspect ratio In2O3 nanowires: Synthesis, mechanism and NO2 gas-sensing properties

Flexural In₂O₃ nanowires with high aspect ratios were synthesized via a hydrothermal–annealing route. The as-synthesized In₂O₃ nanowires had diameters of 30–50 nm and length up to several microns. Various reaction parameters, such as the kind of reagents, the time of hydrothermal treatment, annealing time and annealing temperature, were investigated by a series of control experiments. The as-synthesized In₂O₃ nanowires showed excellent gas-sensing properties to NO₂ in terms of sensor response and selectivity.     

NOx sensing properties of In2O3 nanoparticles prepared by metal organic chemical vapor deposition

In₂O₃ nanoparticles were deposited by low-temperature metal organic chemical vapor deposition. The response of 10-nm thick In₂O₃ particle containing layers to NO_x and O₂ gases is investigated. The lowest detectable NO_x concentration is 200 ppb and the sensor performance is strongly dependent on the gas partial pressure as well as on the operating temperature. The sensor response towards 200 ppm of NO_x is found to be above 10⁴. Furthermore, the cross-sensitivity against O₂ is very low, demonstrating that the In₂O₃ nanoparticles are very suitable for the selective NO_x detection.     

Room-temperature H2S gas sensing at ppb level by single crystal In2O3 whiskers

In₂O₃ whiskers and bipyramidal nano-crystals were prepared by a carbothermal method. These were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), photoluminescence and Raman spectroscopy. These were studied for application to sensing of H₂S gas. The single crystal whiskers were found to be sensitive to as low as 200 ppb of H₂S gas at room temperature and showed saturation in response at 10 ppm. On the other hand, the films made of bipyramids were less sensitive to H₂S gas and the response was found to be a nearly linear function of concentration in a concentration range of 10–80 ppm.     

Ga3O2-和Ga4O3-的结构及稳定性的研究

采用密度泛函理论（DFT）中的B3LYP方法和BP86方法,O原子基于6-311+G（d,p）基组,Ga原子基于Stuttgart基组,对Ga₃O₂^-/0与Ga₄O₃^-/0团簇的各种可能构型进行了几何优化,预测了各团簇的最稳定结构,并研究了Ga₃O₂^-和Ga₄O₃^-最稳定结构的成键特性、振动特性和稳定性。对比B3LYP和BP86计算结果发现得到的异构体的结构和能量顺序相同,且阴离子的基态构型与中性分子的构型相接近,都是平面C_2v型,都存在由2个Ga原子和一个O原子形成的三中心二电子（3c-2e）桥键。两结构中处于端位的"Ga-O"键的Wiberg键级数值较大,分别为0.50、0.55;振动频率分别为713.92、832.76cm-1,在红外谱图上皆对应一明显的强振动峰,表明该"Ga-O"结构单元成键稳定,是决定团簇结构稳定的重要因素。计算得到是Ga₃O₂^-和Ga₄O₃^-基态结构的LUMO与HOMO的能量之差（分别为2.75、2.84eV）,以及电子绝热剥离能（ADE）和电子垂直剥离能（VDE）,都表明两基态结构具有较好的热力学稳定性。     

Preparation and gas-sensing performance of In2O3 porous nanoplatelets

In₂O₃ porous nanoplatelets were successfully synthesized by solvothermal treatment of indium acetylacetonate, followed by calcination in air. X-ray diffraction and Raman spectrum measurements demonstrate that the products are pure cubic phase In₂O₃. Scanning electron microscopy and transmission electron microscopy analyses reveal that the In₂O₃ nanoplatelets bounded by {1 1 0} planes with thickness less than 6 nm and length about 20-50 nm are single crystalline but with porous structure. The optical absorption property of the In₂O₃ nanoplatelets was investigated by UV-vis spectroscopy, which indicates that the In₂O₃ nanoplatelets are semiconducting with a direct band gap of 3.1 eV. The gas sensing performance of the as-prepared In₂O₃ porous nanoplatelets was investigated towards a series of typical organic solvents and fuels. It was found that the In₂O₃ porous nanoplatelets show structure-induced enhancement of gas sensing performance, and especially possess high sensitivity and rapid response towards ethanol vapor.     

Enhanced C2H5OH sensing characteristics of nano-porous In2O3 hollow spheres prepared by sucrose-mediated hydrothermal reaction

In₂O₃ hollow spheres with shell thicknesses of ∼150 nm and ∼300 nm were prepared by the one-pot synthesis of indium-precursor-coated carbon spheres via hydrothermal reaction and subsequent removal of core carbon by heat treatment. The gas response (R_a/R_g, R_a: resistance in air, R_g: resistance in gas) of the thin hollow spheres to 100 ppm C₂H₅OH was 137.2 at 400 °C, which was 1.86 and 3.84 times higher than that of the thick hollow spheres and of the nanopowders prepared by precipitation, respectively. The gas sensing characteristics are discussed in relation to the shell configuration of the hollow spheres. The enhanced gas response of the hollow spheres was attributed to the effective diffusion of analyte gas toward the entire sensor surface via very thin and nano-porous shells.     

Thin film SnO2-based gas sensors: Film thickness influence

The influence of the thickness of SnO₂ films deposited by a spray pyrolysis method on the operating characteristics of gas sensors is analyzed in this paper. It outlines how the thickness of metal oxides is an important parameter for gas sensors in determining the main operating parameters, such as the magnitude and rate of the sensor response and the optimal operating temperature. It is also shown that the optimal film thickness of a gas sensing layer depends on the required sensor parameters.     

Temperature dependent H2S and Cl2 sensing selectivity of Cr2O3 thin films

The conductometric gas sensing characteristics of Cr₂O₃ thin films - prepared by electron-beam deposition of Cr films on quartz substrate followed by oxygen annealing - have been investigated for a host of gases (CH₄, CO, NO₂, Cl₂, NH₃ and H₂S) as a function of operating temperature (between 30 and 300 °C) and gas concentration (1-30 ppm). We demonstrate that these films are highly selective to H₂S at an operating temperature of 100 °C, while at 220 °C the films become selective to Cl₂. This result has been explained on the basis of depletion of chemisorbed oxygen from the surface of films due to temperature and/or interaction with Cl₂/H₂S, which is supported experimentally by carrying out the work function measurements using Kelvin probe method. The temperature dependent selectivity of Cr₂O₃ thin films provides a flexibility to use same film for the sensing of Cl₂ as well as H₂S.     

SnO2-based R134a gas sensor: Sensing materials preparation, gas response and sensing mechanism

Undoped SnO₂ and porous Al₂O₃ powders were obtained through a simple chemical precipitation process. SnO₂-based gas sensing materials and Al₂O₃ catalytic coating loaded with a noble metal were prepared by impregnation. The SnO₂ and Al₂O₃ powders were characterized by TEM, SEM, nitrogen adsorption-desorption experiment, FT-IR and in situ XRD. Gas responses of the SnO₂-based gas sensors were measured in a static state. The experimental results indicated that the response towards R134a of the SnO₂-based gas sensor can be significantly enhanced by loading noble metal and using catalytic coating. The sensor based on a double layer film SnO₂ (Au)/Al₂O₃ (Au) showed satisfactory results including large response, good selectivity, high long-term stability, fast response and recovery, revealing its potential application in the detection of refrigerants and the maintenance of air condition systems. Finally, a gas sensing mechanism for R134a is suggested and proved by bond energy data, FT-IR spectrum and in situ XRD.     

Hydrogen gas sensing properties of Pt/Ta2O5 Schottky diodes based on Si and SiC substrates

We developed Pt/tantalum oxide (Ta₂O₅) Schottky diodes for hydrogen sensing applications. Thin layer (4 nm) of Ta₂O₅ was deposited on silicon (Si) and silicon carbide (SiC) substrates using the radio frequency sputtering technique. We compared the performance of these sensors at different temperatures of 100 °C and 150 °C. At these operating temperatures, the sensor based on SiC exhibited a larger sensitivity, whilst the sensor based on Si exhibited a faster response toward hydrogen gas. We discussed herein, the experimental results obtained for these Pt/Ta₂O₅ based Schottky diodes exhibited that they are promising candidates for hydrogen sensing applications.     

Studies on the gas sensing behaviour of nanosized CuNb2O6 towards ammonia, hydrogen and liquefied petroleum gas

Appreciable changes in resistance of polycrystalline nanosized CuNb₂O₆ upon exposure to reducing gases like hydrogen, liquefied petroleum gas (LPG) and ammonia in ambient atmosphere recognize the material as a gas sensor. Nanosized CuNb₂O₆ synthesized by thermal decomposition of an aqueous precursor solution containing copper nitrate, niobium tartrate and tri-ethanol amine (TEA), followed by calcination at 700 °C for 2 h, has been characterized using X-ray diffraction (XRD) study, transmission electron microscopy (TEM), field-emission scanning electron microscope (FESEM), energy dispersive X-ray (EDX) analysis and Brunauer–Emmett–Teller (BET) surface area measurement. The synthesized CuNb₂O₆ exhibits monoclinic structure with crystallite size of 25 nm, average particle size of 25–40 nm and specific surface area of 55 m² g⁻¹.     

Synthesis of nearly monodisperse Co3O4 nanocubes via a microwave-assisted solvothermal process and their gas sensing properties

Nearly monodisperse Co₃O₄ nanocubes have been prepared by a microwave-assisted solvothermal (MS) method at 180 °C for 20 min. The samples are characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD pattern and TEM images of the products illustrated that Co₃O₄ nanocubes had a cubic phase with a lateral size of ∼20 nm. The gas response of the Co₃O₄ nanocubes was studied to several typical organic gases. The Co₃O₄ nanocubes showed good gas sensing performance towards xylene and ethanol vapors with rapid and high responses at a low-operating temperature. The results showed that the Co₃O₄ nanocubes can be used to fabricate high performance gas sensors.     

铁掺杂In2O3纳米粉体及其气敏性能研究

对 In2O3 粉体进行 Fe 掺杂,采用水热法合成了In2O3 粉体.通过 X 射线衍射(XRD),扫描电镜(SEM),透射电子显微镜(TEM)等手段对粉体的物相、形貌、粒度等进行表征.TEM 图表明:质量分数为7 %Fe 掺杂的样品为均匀排列的棒,长度约为 300～500nm,宽度约 20 nm.对样品进行气敏性能...     

Controlled synthesis and gas-sensing properties of hollow sea urchin-like α-Fe2O3 nanostructures and α-Fe2O3 nanocubes

Hollow sea urchin-like α-Fe₂O₃ nanostructures were successfully synthesized by a hydrothermal approach using FeCl₃ and Na₂SO₄ as raw materials, and subsequent annealing in air at 600 °C for 2 h. The hollow sea urchin-like α-Fe₂O₃ nanostructures with the diameters of 2–4.5 μm consist of well-aligned α-Fe₂O₃ nanorods with an average length of about 1 μm growing radially from the centers of the nanostructures, have a hollow interior with a diameter of about 2 μm. α-Fe₂O₃ nanocubes with a diameter of 700–900 nm were directly obtained by a hydrothermal reaction of FeCl₃ at 140 °C for 12 h. The response S_r (S_r = R_a/R_g) of the hollow sea urchin-like α-Fe₂O₃ nanostructures reached 2.4, 7.5, 5.9, 14.0 and 7.5 to 56 ppm ammonia, 32 ppm formaldehyde, 18 ppm triethylamine, 34 ppm acetone, and 42 ppm ethanol, respectively, which was excess twice that of the α-Fe₂O₃ nanocubes and the nanoparticle aggregations. Our results demonstrated that the hollow sea urchin-like α-Fe₂O₃ nanostructures were very promising for gas sensors for the detection of flammable and/or toxic gases with good-sensing characteristics.     

Synthesis of novel SnO2/ZnSnO3 core-shell microspheres and their gas sensing properities

Large-scale novel core-shell structural SnO₂/ZnSnO₃ microspheres were successfully synthesized by a simple hydrothermal method with the help of the surfactant poly(vinyl pyrrolidone) PVP. The as-synthesized samples were characterized using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). The results indicate that the shell was formed by single crystalline ZnSnO₃ nanorods and the core was formed by aggregated SnO₂ nanoparticles. The effects of PVP and hydrothermal time on the morphology of SnO₂/ZnSnO₃ were investigated. A possible formation mechanism of these hierarchical structures was discussed. Moreover, the sensor performance of the prepared core-shell SnO₂/ZnSnO₃ nanostructures to ethanol was studied. The results indicate that the as-synthesized samples exhibited high response and quick response-recovery to ethanol.     

ZnFe2O4 tubes: Synthesis and application to gas sensors with high sensitivity and low-energy consumption

ZnFe₂O₄ tubes with mesoscale dimensions were synthesized by pyrolysis of polyvinyl alcohol (PVA)-mediated xerogel using porous alumina as a template. The product formation was analyzed by X-ray powder diffraction (XRD), Fourier transformation infrared spectroscopy (FT-IR), thermogravimetry and differential thermal analysis (TG–DTA), scanning electronic microscopy (SEM), transmission electron microscopy (TEM) and high-resolution TEM (HRTEM). This synthetic method yielded open-ended ZnFe₂O₄ tubes with a typical length of several micrometers, an outer diameter of about 200 nm, and an average thin wall of 20 nm composed of small nanocrystals. Application of the ZnFe₂O₄ tubes as gas sensor materials displayed low-energy consumption and high sensitivity to organics such as ethanol and acetone, due to the unique interconnected channel structure and small crystal size of the tubes, showing their potential application in sensor areas.     

Enhancing performance of FSP SnO2-based gas sensors through Sb-doping and Pd-functionalization

Via flame spray pyrolysis (FSP), SnO₂ gas sensing layers have been doped with 0.01-4 wt% Sb as well as 0.01 wt% Pd in combination with 1 wt% Sb. Characterization of these materials through X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface analysis, and transmission electron microscopy (TEM) revealed particle grain sizes and crystallinity unchanged by the presence of Sb and/or Pd. The addition of Sb to SnO₂ resulted in the significant decrease in baseline resistance; up to two orders of magnitude in dry air at 300 °C and three orders of magnitude in humid air at 300 °C, which is significant for FSP-prepared gas sensors with high porosity and low particle coordination number since they typically suffer from high baseline resistance. While the baseline resistance was improved with Sb-doping, the sensor signal (R₀/R_gas) remained constant over all concentrations explored. Moreover, regarding the surface functionalization of SnO₂ with Pd in combination with Sb-doping, the reduction of baseline resistance was preserved without influencing sensor signal.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

介孔SnO2气敏性能研究

为了改善传感器的气敏性能,采用溶胶-凝胶法合成了介孔SnO2,并研究了其气敏性能.研究表明:与纳米SnO2相比,介孔SnO2气体传感器具有较高的酒精、二甲苯响应,在100～150℃对甲醛的响应也大大提升.在100～ 150℃,干扰气体为甲苯和二甲苯时,介孔SnO2表现远远优越于纳米SnO2的酒精选择性.在100,150,350℃,干扰气体为甲苯时,介孔SnO2也具有优越的甲醛选择性.介孔SnO2的响应时间较短,但恢复时间较长.     

Au-doped WO3-based sensor for NO2 detection at low operating temperature

Pure and Au-doped WO₃ powders for NO₂ gas detection were prepared by a colloidal chemical method, and characterized via X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The NO₂ sensing properties of the sensors based on pure and Au-doped WO₃ powders were investigated by HW-30A gas sensing measurement. The results showed that the gas sensing properties of the doped WO₃ sensors were superior to those of the undoped one. Especially, the 1.0 wt% Au-doped WO₃ sensor possessed larger response, better selectivity, faster response/recovery and better longer term stability to NO₂ than the others at relatively low operating temperature (150 °C).