Structural and electrochemical properties of Cl-doped LiFePO4/C

Cl-doped LiFePO₄/C cathode materials were synthesized through a carbothermal reduction route, and the microstructure and electrochemical performances were systematically studied. Cl-doped LiFePO₄/C cathode materials presented a high discharge capacity of ∼90 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. Electrochemical impedance spectroscopy and cyclic voltamperometry indicated the optimized electrochemical reaction and Li⁺ diffusion in the bulk of LiFePO₄ due to Cl-doping. The improved Li⁺ diffusion capability is attributed to the microstructure modification of LiFePO₄ via Cl-doping.     

A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Improved electrochemical performances of 9LiFePO4·Li3V2(PO4)/C composite prepared by a simple solid-state method

9LiFePO₄·Li₃V₂(PO₄)₃/C is synthesized via a carbon thermal reaction using petroleum coke as both reduction agent and carbon source. The as-prepared material is not a simple mixture of LiFePO₄ (LFP) and Li₃V₂(PO₄)₃ (LVP), but a composite possessing two phases: one is V-doped LFP and the other is Fe-doped LVP. The typical structure enhances the electrical conductivity of the composite and improves the electrochemical performances. The first discharge capacity of 9LFP·LVP/C in 18650 type cells is 168 mAh g⁻¹ at 1 C (1 C_9LFP·LVP/C = 166 mA g⁻¹), and exhibits high reversible discharge capacity of 125 mAh g⁻¹ at 10 C even after 150 cycles. At the temperature of −20 °C, the reversible capacity of 9LFP·LVP/C can maintain 75% of that at room temperature.     

Synthesis and electrochemical characterization of carbon-coated nanocrystalline LiFePO4 prepared by polyacrylates-pyrolysis route

A carbon-coated nanocrystalline LiFePO₄ cathode material was synthesized by pyrolysis of polyacrylate precursor containing Li⁺, Fe³⁺ and PO₄⁻. The powder X-ray diffraction (XRD) and high-resolution TEM micrographs revealed that the LiFePO₄/C composite as prepared has a core-shell structure with pure olivine LiFePO₄ crystallites as cores and intimate carbon coating as a shell layer. Between the composite particulates, there exists a carbon matrix binding the nanocrystallites together into micrometer particles. The electrochemical measurements demonstrated that the LiFePO₄/C composite with an appropriate carbon content can deliver a very high discharge capacity of 157 mAh g⁻¹ (>92% of the theoretical capacity of LiFePO₄) with 95% of its initial capacity after 30 cycles. Since this preparation method uses less costly materials and operates in mild synthetic conditions, it may provide a feasible way for industrial production of the LiFePO₄/C cathode materials for the lithium-ion batteries.     

Electrochemical properties of LiFePO4 prepared via hydrothermal route

LiFePO₄ as a cathode material for rechargeable lithium batteries was prepared by hydrothermal process at 170 °C under inert atmosphere. The starting materials were LiOH, FeSO₄, and (NH₄)₂HPO₄. The particle size of the obtained LiFePO₄ was 0.5 μm. The electrochemical properties of LiFePO₄ were characterized in a mixed solvent of ethylene carbonate and diethyl carbonate (1:1 in volume) containing 1.0 mol dm⁻³ LiClO₄. The hydrothermally synthesized LiFePO₄ exhibited a discharge capacity of 130 mA h g⁻¹, which was smaller than theoretical capacity (170 mA h g⁻¹). The annealing of LiFePO₄ at 400 °C in argon atmosphere was effective in increasing the discharge capacity. The discharge capacity of the annealed LiFePO₄ was 150 mA h g⁻¹.     

Synthesis of carbon-coated LiFePO4 nanoparticles with high rate performance in lithium secondary batteries

A novel preparation technique was developed for synthesizing carbon-coated LiFePO₄ nanoparticles through a combination of spray pyrolysis (SP) with wet ball milling (WBM) followed by heat treatment. Using this technique, the preparation of carbon-coated LiFePO₄ nanoparticles was investigated for a wide range of process parameters such as ball-milling time and ball-to-powder ratio. The effect of process parameters on the physical and electrochemical properties of the LiFePO₄/C composite was then discussed through the results of X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the Brunauer-Emmet-Teller (BET) method and the use of an electrochemical cell of Li|1 M LiClO₄ in EC:DEC = 1:1|LiFePO₄. The carbon-coated LiFePO₄ nanoparticles were prepared at 500 °C by SP and then milled at a rotating speed of 800 rpm, a ball-to-powder ratio of 40/0.5 and a ball-milling time of 3 h in an Ar atmosphere followed by heat treatment at 600 °C for 4 h in a N₂ + 3% H₂ atmosphere. SEM observation revealed that the particle size of LiFePO₄ was significantly affected by the process parameters. Furthermore, TEM observation revealed that the LiFePO₄ nanoparticles with a geometric mean diameter of 146 nm were coated with a thin carbon layer of several nanometers by the present method. Electrochemical measurement demonstrated that cells containing carbon-coated LiFePO₄ nanoparticles could deliver markedly improved battery performance in terms of discharge capacity, cycling stability and rate capability. The cells exhibited first discharge capacities of 165 mAh g⁻¹ at 0.1 C, 130 mAh g⁻¹ at 5 C, 105 mAh g⁻¹ at 20 C and 75 mAh g⁻¹ at 60 C with no capacity fading after 100 cycles.     

Effect of synthesis temperature on the properties of LiFePO4/C composites prepared by carbothermal reduction

LiFePO₄/C composite cathode materials were synthesized by carbothermal reduction method using inexpensive FePO₄ as raw materials and glucose as conductive additive and reducing agent. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and particle size analysis. Cyclic voltammetry (CV) and charge/discharge cycling performance were used to characterize their electrochemical properties. The results showed that the LiFePO₄/C composite synthesized at 650 °C for 9 h exhibited the most homogeneous particle size distribution. Residual carbon during processing was coated on LiFePO₄, resulting in the enhancement of the material's electronic properties. Electrochemical measurements showed that the discharge capacity first increased and then decreased with the increase of synthesis temperature. The optimal sample synthesized at 650 °C for 9 h exhibited a highest initial discharge capacity of 151.2 mA h g⁻¹ at 0.2 C rate and 144.1 mA h g⁻¹ at 1 C rate with satisfactory capacity retention rate.     

Preparation and characterization of Na-doped LiFePO4/C composites as cathode materials for lithium-ion batteries

To improve the performance of LiFePO₄, single phase Li_1−xNa_xFePO₄/C (x = 0, 0.01, 0.03, 0.05) samples are synthesized by in situ polymerization restriction-carbonthermal reduction method. The effects of Na doping are studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results indicate that doped Na ion does not destroy the lattice structure of LiFePO₄, while enlarges the lattice volume. Electrochemical test results show that the Li_0.97Na_0.03FePO₄/C sample exhibits the best electrochemical performance with initial special discharge capacity of 158 mAh g⁻¹ at 0.1 C. EIS results demonstrate that the charge transfer resistance of the sample decreases greatly by doping an appropriate amount of Na.     

Effects of roasting temperature and modification on properties of Li2FeSiO4/C cathode

Li₂FeSiO₄/C cathodes were synthesized by combination of wet-process method and solid-state reaction at high temperature, and effects of roasting temperature and modification on properties of the Li₂FeSiO₄/C cathode were investigated. The XRD patterns of the Li₂FeSiO₄/C samples indicate that all the samples are of good crystallinity, and a little Fe₃O₄ impurity was observed in them. The primary particle size rises as the roasting temperature increases from 600 to 750 °C. The Li₂FeSiO₄/C sample synthesized at 650 °C has good electrochemical performances with an initial discharge capacity of 144.9 mAh g⁻¹ and the discharge capacity remains 136.5 mAh g⁻¹ after 10 cycles. The performance of Li₂FeSiO₄/C cathode is further improved by modification of Ni substitution. The Li₂Fe_0.9Ni_0.1SiO₄/C composite cathode has an initial discharge capacity of 160.1 mAh g⁻¹, and the discharge capacity remains 153.9 mAh g⁻¹ after 10 cycles. The diffusion coefficient of lithium in Li₂FeSiO₄/C is 1.38 × 10⁻¹² cm² s⁻¹ while that in Li₂Fe_0.9Ni_0.1SiO₄/C reaches 3.34 × 10⁻¹² cm² s⁻¹.     

Electrochemical properties of LiFe0.9Mn0.1PO4/Fe2P cathode material by mechanical alloying

LiFePO₄, olivine-type LiFe_0.9Mn_0.1PO₄/Fe₂P composite was synthesized by mechanical alloying of carbon (acetylene back), M₂O₃ (M = Fe, Mn) and LiOH·H₂O for 2 h followed by a short-time firing at 900 °C for only 30 min. By varying the carbon excess different amounts of Fe₂P second phase was achieved. The short firing time prevented grain growth, improving the high-rate charge/discharge capacity. The electrochemical performance was tested at various C/x-rate. The discharge capacity at 1C rate was increased up to 120 mAh g⁻¹ for the LiFe_0.9Mn_0.1PO₄/Fe₂P composite, while that of the unsubstituted LiFePO₄/Fe₂P and LiFePO₄ showed only 110 and 60 mAh g⁻¹, respectively. Electronic conductivity and ionic diffusion constant were measured. The LiFe_0.9Mn_0.1PO₄/Fe₂P composite showed higher conductivity and the highest diffusion coefficient (3.90 × 10⁻¹⁴ cm² s⁻¹). Thus the improvement of the electrochemical performance can be attributed to (1) higher electronic conductivity by the formation of conductive Fe₂P together with (2) an increase of Li⁺ ion mobility obtained by the substitution of Mn²⁺ for Fe²⁺.     

Hydrothermal preparation of LiFePO4 nanocrystals mediated by organic acid

Well-crystallized LiFePO₄ nanoparticles have been directly synthesized in a short time via hydrothermal process in the presence of organic acid, e.g. citric acid or ascorbic acid. These acid-mediated LiFePO₄ products exhibit a phase-pure and nanocrystal nature with size about 50-100 nm. Two critical roles that the organic acid mediator plays in hydrothermal process are recognized and a rational mechanism is explored. After a post carbon-coating treatment at 600 °C for 1 h, these mediated LiFePO₄ materials show a high electrochemical activity in terms of reversible capacity, cycling stability and rate capability. Particularly, LiFePO₄ mediated by ascorbic acid can deliver a capacity of 162 mAh g⁻¹ at 0.1 C, 154 mAh g⁻¹ at 1 C, and 122 mAh g⁻¹ at 5 C. The crystalline structure, particle morphology, and surface microstructure were characterized by high-energy synchrotron X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), and Raman spectroscopy, respectively. And the electrochemical properties were thoroughly investigated by galvanostatic test and electrochemical impedance spectroscopy (EIS).     

Optimized solid-state synthesis of LiFePO4 cathode materials using ball-milling

Olivine-type LiFePO₄ cathode materials were synthesized by a solid-state reaction method and ball-milling. The ball-milling time, heating time and heating temperature are optimized. A heating temperature higher than 700 °C resulted in the appearance of impurity phase Fe₂P and growth of large particle, which was shown by high resolution X-ray diffraction and field emission scanning electron microscopy. The impurity phase Fe₂P exhibited a considerable capacity loss at the 1st cycle and a gradual increase in discharge capacity upon cycling. Moreover, it exhibited an excellent high-rate capacity of 104 mAh g⁻¹ at 3 C in spite of the large particle size. The optimum synthesis conditions for LiFePO₄ were ball-milling for 24 h and heat-treatment at 600 °C for 3 h. LiFePO₄/Li cells showed an enhanced cycling performance and a high discharge capacity of 160 mAh g⁻¹ at 0.1 C.     

Synthesis and electrochemical properties of olivine LiFePO4 prepared by a carbothermal reduction method

LiFePO₄/C composite cathode material was prepared by carbothermal reduction method, which uses NH₄H₂PO₄, Li₂CO₃ and cheap Fe₂O₃ as starting materials, acetylene black and glucose as carbon sources. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. X-ray diffraction (XRD), scanning electron microscopy (SEM) micrographs showed that the LiFePO₄/C is olivine-type phase, and the addition of the carbon reduced the LiFePO₄ grain size. The carbon is dispersed between the grains, ensuring a good electronic contact. The products sintered at 700 °C for 8 h with glucose as carbon source possessed excellent electrochemical performance. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 159.3 mAh g⁻¹ at 0.1 C rate, and the capacity fading is only 2.2% after 30 cycles.     

Basic molten salt process—A new route for synthesis of nanocrystalline Li4Ti5O12-TiO2 anode material for Li-ion batteries using eutectic mixture of LiNO3-LiOH-Li2O2

A nanocrystalline Li₄Ti₅O₁₂-TiO₂ duplex phase has been synthesized by a simple basic molten salt process (BMSP) using an eutectic mixture of LiNO₃-LiOH-Li₂O₂ at 400-500 °C. The microstructure and morphology of the Li₄Ti₅O₁₂-TiO₂ product are characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The sample prepared by heat-treating at 300 °C for 3 h (S-1) reveals dense agglomerates of ultra-fine nanocrystalline Li₄Ti₅O₁₂; with heat treatment at 400 °C for 3 h (S-2), there is a duplex crystallite size (fine < 10 nm, and coarse > 20 nm) of Li₄Ti₅O₁₂-TiO₂; at 500 °C for 3 h (S-3), a much coarser and less-dense distribution of lithium titanate (crystallite size ∼15-30 nm) is observed. According to the results of electrochemical testing, the S-2 sample shows initial discharge capacities of 193 mAh g⁻¹ at 0.2 C, 168 mAh g⁻¹ at 0.5 C, 146 mAh g⁻¹ at 1 C, 135 mAh g⁻¹ at 2 C, and 117 mAh g⁻¹ at 5 C. After 100 cycles, the discharge capacity is 138 mAh g⁻¹ at 1 C with a capacity retention of 95%. The S-2 sample yields the best electrochemical performance in terms of charge-discharge capacity and rate capability compared with other samples. Its superior electrochemical performance can be mainly attributed to the duplex crystallite structure, composed of fine (<10 nm) and coarse (>20) nm nanoparticles, where lithium ions can be stored within the grain boundary interfaces between the spinel Li₄Ti₅O₁₂ and the anatase TiO₂.     

Effects of Fe2P and Li3PO4 additives on the cycling performance of LiFePO4/C composite cathode materials

In this study, a solution method was employed to synthesize LiFePO₄-based powders with Li₃PO₄ and Fe₂P additives. The composition, crystalline structure, and morphology of the synthesized powders were investigated by using ICP-OES, XRD, TEM, and SEM, respectively. The electrochemical properties of the powders were investigated with cyclic voltammetric and capacity retention studies. The capacity retention studies were carried out with LiFePO₄/Li cells and LiFePO₄/MCMB cells comprised LiFePO₄-based materials prepared at various temperatures from a stoichiometric precursor. Among all of the synthesized powders, the samples synthesized at 750 and 775 °C demonstrate the most promising cycling performance with C/10, C/5, C/2, and 1C rates. The sample synthesized at 775 °C shows initial discharge capacity of 155 mAh g⁻¹ at 30 °C with C/10 rate. From the results of the cycling performance of LiFePO₄/MCMB cells, it is found that 800 °C sample exhibited higher polarization growth rate than 700 °C sample, though it shows lower capacity fading rate than 700 °C sample. For Fe₂P containing samples, the diffusion coefficient of Li⁺ ion increases with increasing amount of Fe₂P, however, the sample synthesized at 900 °C shows much lower Li⁺ ion diffusion coefficient due to the hindrance of Fe₂P layer on the surface of LiFePO₄ particles.     

Preparation and electrochemical properties of carbon-doped TiO2 nanotubes as an anode material for lithium-ion batteries

Carbon-doped TiO₂ nanotubes were synthesized through a sol–gel and subsequent hydrothermal process. Transmission electron microscopy and X-ray diffraction showed that the products are uniformly straight tubes with the diameter around 10 nm in anatase-type. The electrochemical performances of the nanotubes were tested by constant current discharge/charge, cyclic voltammetry, and electrochemical impedance spectroscopy. The initial discharge capacity reaches 291.7 mAh g⁻¹ with a coulombic efficiency of 91.7% at a current density of 70 mA g⁻¹. There is a distinct potential plateau near 1.75 and 1.89 V (versus Li⁺/Li) in the lithium intercalation and extraction processes, respectively, and the lithium insertion capacity is about 204 mAh g⁻¹ over the plateau of 1.75 V region in the first cycle. From the 2nd to the 30th cycles, the average reversible capacity loss is less than 1.73 mAh g⁻¹ per cycle. After 30 cycles, the reversible capacity still remains 211 mAh g⁻¹ with a coulombic efficiency larger than 99.7%, implying a perfect reversibility and cycling stability.     

Synthesises,characterizations and electrochemical properties of spherical-like LiFePO4 by hydrothermal method

Spherical-like LiFePO₄ was synthesized by hydrothermal synthesis method using Phenanthroline as a complexing-agent to avoid the Fe(II) ions from oxidation and control the growth of the crystal. Structural, electron valence state, morphology and particle size were investigated by X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), Mössbauer spectra, scanning electron microscopy (SEM) and laser particle sizer. Charge–discharge cycling performances were used to characterize its electrochemical properties. The sample possesses uniformly distributed spherical-like particles with an average size of 0.5–1 μm. Test shows that the reversible capacity of spherical-like LiFePO₄ is about 140 mAh g⁻¹ at 0.1 C. The capacity fading is neglectable.     

Synthesis of LiFePO4/C composite with high-rate performance by starch sol assisted rheological phase method

LiFePO₄/C composite was synthesized at 600 °C in an Ar atmosphere by a soluble starch sol assisted rheological phase method using home-made amorphous nano-FePO₄ as the iron source. XRD, SEM and TEM observations show that the LiFePO₄/C composite has good crystallinity, ultrafine sphere-like particles of 100-200 nm size and in situ carbon. The synthesized LiFePO₄ could inherit the morphology of FePO₄ precursor. The electrochemical performance of the LiFePO₄ by galvanostatic cycling studies demonstrates excellent high-rate cycle stability. The Li/LiFePO₄ cell displays a high initial discharge capacity of more than 157 mAh g⁻¹ at 0.2C and a little discharge capacity decreases from the first to the 80th cycle (>98.3%). Remarkably, even at a high current density of 30C, the cell still presents good cycle retention.     

A novel method for synthesis of layered LiNi1/3Mn1/3Co1/3O2 as cathode material for lithium-ion battery

The layered LiNi_1/3Mn_1/3Co_1/3O₂ materials with good crystalline are synthesized by a novel method of hydrothermal method followed by a short calcination process. The crystalline structure and morphology of the synthesized materials are characterized by XRD, SEM. Their electrochemical performances are evaluated by CV, EIS and galvonostatic charge/discharge tests. The material synthesized at 850 °C for 6 h shows the highest initial discharge capacity of 187.7 mAh g⁻¹ at 20 mA g⁻¹. And the capacity retention of 97.9% is maintained at the end of 40 cycles at 1.0 C. CV test reveals almost no shift of anodic and cathodic peaks after first cycle, which indicates good reversible deintercalation and intercalation of Li⁺ ions.     

Morphology and electrical properties of carbon coated LiFePO4 cathode materials

Core-shell LiFePO₄@C composites were synthesized successfully from FePO₄/C precursor using the polyvinyl alcohol (PVA) as the reducing agent, followed by a chemical vapor deposition (CVD) assisted solid-state reaction in the presence of Li₂CO₃. Some physical and chemical properties of the products were characterized by X-ray powder diffraction (XRD), Raman, SEM, TEM techniques. The effect of morphology and electrochemical properties of the composites were thoroughly investigated. XRD patterns showed that LiFePO₄ has an order olivine structure with space group of Pnma. TEM micrographs exhibited that the LiFePO₄ particles encapsulated with 3-nm thick carbon shells. The powders were homogeneous with grain size of about 0.8 μm. Compared with those synthesized by traditional organic carbon source mixed method, LiFePO₄@C composite synthesized by CVD method exhibited better discharge capacity at initial 155.4 and 135.8 mAh g⁻¹ at 0.1C and 1C rate, respectively. It is revealed that the carbon layer coated on the surface of LiFePO₄ and the amorphous carbon wrapping and connecting the particles enhanced the electronic conductivity and rate performances of the cathode materials.